Search Documents

Commodities statistics and other information are available through the following three systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack. Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

By R. E. Heithecker, Van A. Mills

"Crude oils are capable of dissolving quantities of gas under pressure. This fact has been known for some time, but questions have arisen as to the effects of gas in solution upon the characteristics of the oil. Previous investigations4 show that gas in solution in an oil affects the viscosity and surface tension of the oil, but the effects on the volume and A. P. I. gravity of the oil have not been known. The results given in this report show that there is a decided change both in volume and in the A. P. I. gravity of the oil due to the solution of the gas in the oil under pressure. As gas is dissolved, the volume of the oil and the A. P. I. gravity increase. The converse of this phenomenon is also true: if the gas is released from a saturated oil, there is a shrinkage in volume and a decrease in A.P.I. gravity due to the release of gas from solution. However, various oils show marked tendencies to retain a portion of the dissolved gas upon releasing the pressure to that of the atmosphere. This retained gas has an appreciable effect on the volume and A. P. I. gravity of the oil because the oil does not resume its initial volume or gravity while it retains dissolved gas. In a sense the oil has been ""freshened"" and will not return to its original or weathered volume until it loses some of the lighter fractions. Wiggins5 has shown that a fresh oil decreases both in volume and in gravity because of the weathering of the lighter fractions while the oil is standing in storage tanks.This paper includes data attained during the determination of volume and gravity correction factors to be applied in the oil recovery investigations of the Bureau of Mines. Three oils having a wide range in gravity were used in determining the correction factors. These oils were from the Bartlesville-Dewey field, Oklahoma, the Seminole field, Oklahoma, and the Inglewood field, California. The same gas that was used in the oil recovery experiments was used throughout this investigation. Determinations were made of the volume and A.P.I. gravity increases resulting from the gas going into solution at 200, 400, 600, 800, and 1,000 pounds pressure; also the increases in the volume and gravity of the oil due to retained gas were determined after the dissolved gas was liberated from solution by releasing the pressure to that of the atmosphere.Samples of residual and liberated gas were taken throughout the investigation in order to study the selective absorption and selective retention by the oil of the various constituents of the gas. The analyses of these gas samples showed that there was selective absorption and selective retention of the constituents of the gas. The tests on Inglewood crude gave the most pronounced example of selective absorption and selective retention of the gas.All of the tests were conducted at a constant temperature of 709F."

Oct 1, 1928

By G. R. Hopkins, E. W. COCHRANE

According to reports received by the United States Bureau of Mines , Department of Commerce , as of January 1 , 1930 , there were 412 completed refineries in the United States with a daily crude oil capacity of 3,755,585 barrels . This compares with 413 refineries of 3,509,540 barrels capacity on January 1 , 1929 , which indicates that whereas the number of refineries was practically unchanged , the total capacity increased 8 per cent during the past year . Of the completed plants as of January 1 , 1930 , 358 plants , of 3,634,825 barrels total capacity , were operating and 54 , with a capacity of 130,760 barrels , were shut down . Compared with a year ago , this indicates a decline in the percentage of the total refinery capacity that is inoperative . There has been a decided decrease in the number of shut-down plants since 1924 and 1925 , when one plant in every three was inoperative . Many of the inoperative plants of 1924 and 1925 were constructed soon after the boom times of 1920. Some of these were operated for a time but were unable to show a profit during 1923 and 1924 , when an overproduction of crude petroleum was accompanied by demoralized markets for refined products . Prices for refined products improved in 1925 and 1926 , but only a comparatively few of the shut -down plants , then partly obsolete , were able to obtain or renew their crude connections and compete successfully with the larger , more firmly established refineries . After five years or more of continuous idleness , a refinery would be rendered practically useless through corrosion and obsolescence . Consequently , most plants now being carried as " shut -down " have operated intermittently since 1923 . struction . A material change occurred in 1929 in the matter of plants under con- On January 1 , 1929 , there were 14 plants under construction , with a potential capacity of 99,000 barrels per day , whereas on January 1 , 1930 , there were only eight plants of 37,200 barrels capacity being built . This decline was due to the fact that the construction program in west Texas , which was at or near its height on January 1 , 1929 , was completed prior to January 1 , 1930 .

Apr 1, 1930

By A. S. Peck

This report presents the results of a cooperative study between the Bureau of Mines and the University of Utah to define the mechanism involved in the adsorption of oleic acid and sodium oleate on fluorite, calcite, and barite, using an infrared spectrophotometer for identifying and measuring the adsorbed reagents and reaction products. Fluorite, calcite, and barite react with oleic acid and sodium oleate in a water system, forming chemisorbed and solution products. The chemisorbed species is a surface mineral cation-collector anion salt, Chemical analysis of solution resulting from the adsorption reaction indicates that the adsorption process causes displacement of mineral anions, namely, fluoride, carbon ate, and sulfate from the surface of these minerals.

Jan 1, 1963

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By H. J. Heinen

This report summarizes preliminary research studies by the Bureau of Mines in electrowinning molybdenum directly from pure or impure molybdenum trioxide (MoO3) by fused-bath electrolysis in an open graphite cell without need of a protective inert atmosphere. A formulated electrolyte of the tertiary system containing 41.6 percent sodium pyrophosphate, 16.7 percent sodium tetraborat, 33.3 percent sodium chloride, and 8,4 percent molybdenum trioxide, by weight, electrolyzed at 1,000° C,, gave excellent results. Current density studies were made over a range from 20 to 260 amperes per square decimeter. Current efficiencies of 80 to 90 percent were obtained over the entire range. Yields up to 500 grams of molybdenum per kilowatt-hour were obtained. Higher current densities, however, reduced yields and produced a finer grained metal. The two most important facets in electrowinning molybdenum from MoO3, in an open cell, are temperature and electrode spacing to minimize or eliminate the formation of the suboxide MoO2, the major source of oxygen contamination. At temperatures of 1,000° C. and higher, together with the proper spacing of the electrodes, formation of oxides are practically eliminated. Molybdenum metal electrowon from pure MoO3 was 99.9 percent pure and contained 0,056 percent oxygen and 0,007 percent carbon. This metal, when arc-melted, had a Vickers hardness number of 175 and contained 50 parts per million oxygen and less than 10 parts per million carbon. Molybdenum metal electrowon directly from an impure MoO3 containing 90 percent MoO3 resulted in a metal of 99.8 percent purity.

Jan 1, 1961

By C. A. Herbert

In summer, when hot, moisture-laden air enters a coal mine in the region east of the Mississippi River, the moisture is likely to condense on the roof and ribs because the incoming air is cooled below its dew point upon contact with the roof, ribs, and floor of the mine passageways. When the roof and ribs become wet owing to this condensation they are said to "sweat." In many mines, as soon as this sweating begins, shale or slate roof that appears solid and strong in winter begins to cut and fall. For a long time most mining men believed (many still believe) that the roof trouble was due to this sweating. However, from observation of conditions in one mine the operators concluded that the trouble was caused by expansion and contraction of the roof due to changes of temperature. This opinion was confirmed by experiments at several mines in cooling the air as it entered the mines. Methods used in these mines for cooling the air are described in this circular. MINE A At mine A the roof gave considerable trouble in the summer, and it was observed that where a spray of water from a leaking dam kept the roof wet and at a uniform temperature no difficulty was experienced with the roof, although it had cut and fallen on either side of that point. From this fact the company officials concluded that changes of temperature in the air rather than moisture caused the trouble and that if the incoming air were cooled to approximately normal strata temperature much of the additional roof trouble experienced during the summer would be overcome.

Jan 1, 1940

By Seth C. Schaefer

The Bureau of Mines has determined the standard Gibbs energies (AGf°) of CoS1.035 (cobalt sulfide) and Ni2.515S2 (nickel sulfide) with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, CoS1.035, CoO, S02(g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt, with the overall cell reaction C0S1.035(c) + 1.535 02(g, 0.0114 atm) = CoO(c) + 1.035 S02(g)¬ These results, combined with the best available data for ?Gf° of CoO and S02 from the literature, give the standard Gibbs energy of formation of CoS1.035 for the reaction Co(c) + 0 5175 S2(g) = CoS1.035(c) ?Gf° = -38.890 + 18.87 x 10-3T ± 0.185 kcal/mole (866.0 - 1,104.9 K), where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, N12.515S2, NiO, S02(g, 1 atm)//Zr02//02(g, 0.0122 atm), Pt, with the overall cell reaction Ni2.515S2(c) + 3.2575 02(g, 0.0122 atm) = 2.515 NiO(c) + 2 S02(g). Combination of these results with data for ?Gfo of NiO and S02 from the literature yields the standard Gibbs energy of formation of Ni2.515S2 for the reaction 2.515 Ni(c) + S2(g) = Ni2.S1SS2(c) ?Gf° -65.377 + 24.67 x 10-3T ± 0.541 kcal/mole (968.6 -1,053.7 K).

Jan 1, 1981

By Ted A. Lewtas

The effectiveness of induction fans in ventilating dead headings was studied in the laboratory and underground. The following fan attachments were evaluated: a. Aerodynamic nozzle b. Various lengths of vent tube c. Honeycomb airflow straightener. Various fan locations were also tested. The following conclusions were reached: a. A nozzle on a fan located against the drift wall gives the greatest jet penetration distance. b. Air straighteners are ineffective in increasing jet penetration. c. Induction fans are ineffective in removing contaminants from dead headings without sufficient main ventilation flow.

Jan 1, 1980

By J. G. Kirby

The total number of petroleum refineries in the United States decreased during 1951, while the total crude-oil charging capacity continued to increase. There were 350 refineries as of January 1, 1952, compared with 357 a year earlier, according to the annual Bureau of Mines capacity survey. A gain of 369,241 barrels in daily refinery crude through-put capacity during 1951 brings the total to 7,332,885 barrels daily. The capacity of the average refinery to process crude-oil was 20,951 barrels daily, an increase of 1,445 barrels daily over the previous year. Capacity added in the Texas Gulf district accounted for 36 percent of the total increase; the Indiana-Illinois-Kentucky district, 23 percent; the East Coast district, 19 percent; the Oklahoma-Kansas district, 12 percent; and the Texas Inland district, 11 percent. The California district was the only one reporting a decline in crude-oil refining capacity, the total being 14,200 barrels daily below the previous year. Reported as under construction January 1, 1952, was an additional crude-oil capacity of 282,680 barrels daily, an increase of 77 percent over the January 1, 1951, total of 160,100 barrels. The capacity now building is for the expansion of existing facilities, since no new plants had been begun as of the first of the year. Three or four companies have plans to build refineries in the Williston Basin area of North Dakota, but no definite locations or dates when construction will begin have been announced.

Jan 1, 1952

By Jack G. Croeni

A study was made by the Bureau of Mines to determine the influence of high energy-rate deformation on the structures and properties of low-carbon steel, stainless steel, titanium, titanium-6 percent aluminum-4 percent vanadium, beryllium, molybdenum, and tungsten. The purpose of this study was to determine relative formability, the effect of energy and temperature on metalworking parameters and resulting structures, and the properties of materials formed by this technique. Forming techniques were limited to upset forging and direct extrusion on pneumatic-mechanical forming machines. Results show that considerable grain refinement can be achieved by careful control of deformation and forming temperature by high energy-rate techniques. Significant improvements in strength were observed as a result of this refined structure. Approximate deformation resistance as a function of temperature was determined for a variety of materials.

Jan 1, 1966

By Fred N. Kissell

Air recirculation caused by dust scrubbers at coal mine working faces was examined by the Federal Bureau of Mines with regard to the potential hazards caused by a possible buildup of methane gas. A theoretical analysis indicated that there was no apriori way to predict the effect of scrubber recirculation on methane concentration levels. Experiments conducted in a full-scale model of a working face area indicated that methane levels were dependent to a great extent on the location of the scrubber exhaust, but that the scrubber recirculation did not substantially increase the methane concentration above those levels that would have prevailed were the scrubber not in operation. An analysis of two underground scrubber trials showed that the scrubbers had no significant effect on methane levels, and a review of explosions attributed to recirculation showed that these were characterized by a lack of fresh air as well as recirculation. It was concluded that high methane levels are due more to a lack of fresh air than to recirculation.

Jan 1, 1975

By W. E. Anable

The Bureau of Mines studied the purification of commercially available yttrium by melting it in a 100-kw electron-beam furnace. Button-scale melts were made to determine the ultimate purification that could be attained by melting yttrium at 1,733° to 1,770° C at low pressure (0.05 to 0.1 micron) for 1 to 120 minutes. In addition, numerous melts were made to study the effect of doping yttrium with carbon, 17 selected metallic additions, and 3 compounds. Except for nickel and zirconium, the metallic impurities in yttrium were lowered significantly on extended treatment; silicon was lowered only slightly. The nonmetallic impurities} oxygen, nitrogen, and carbon, were not lowered except on short exposures. In isolated instances, the oxygen content was lowered from 5,860 ppm to about 5,000 ppm. In most instances the carbon con-tent was lowered from 545 to about 220 ppm in 20 minutes and then increased again. It was concluded that yttrium cannot be purified by direct heating or by the doping technique employed.

Jan 1, 1965

By William C. McLaughlin

In the deep vein mines of the Coeur d'Alene mining district, rock bursts are a potential hazard to the mine structure and underground personnel. Damage repair costs are estimated by one company to exceed $1 per ton of ore mined. The Bureau of Mines, in cooperation with the mining companies, has conducted research intermittently over the past 10 years to help reduce bursts. Onsite inspections of major rock bursts were conducted, and reports were submitted to mine management; these included the geology and geometry of the affected area. The paper discusses the development and improvement of microseismic and surface monitoring equipment. The underground microseismic network, when operated on a regular basis and the results plotted daily, is capable of detecting stress concentration in certain areas. The surface seismographs record rock bursts, blasts, earthquakes, etc., throughout the district and show approximate location, time, and relative intensity of the event.

Jan 1, 1976

By E. A. Pelczarski

Initially, the objective of this contract was to develop a PWSCSR that could meet proposed criteria (that were different from 30 CFR 11(Title 30 of the Code of Federal Regulation part II) and that would be less than twice the size and weight of a filter self rescuer. This objective was met. Consequently, the original contract was extended to develop a PWSCSR that would meet existing CFR-30 criteria within the same size and weight constraints. This resulted in the development of a PWSCSR (the SR-100) that received NIOSH/MSHA approval (TC-239). This report presents a historical discussion of the design and development of the SR-100 as developed by CSE Corporation under Bureau of Mines contract number H0368013. The technical parameters and the test results of NIOSH/MSHA 30 CFR 11 certification are also presented.

Jan 1, 1990

By Frank J. Wiebelt

In its efforts to maintain production of tungsten during the recent war period, the Bureau of Mines explored certain parts of the properties of the Atolia Mining Co. in San Bernardino County, Calif., by diamond drilling. Owing to past production record and other available data, the area was considered attractive for possible development of new ore bodies. Scheelite occurs in narrow veins ranging in width from a fraction of an inch to several feet. The veins are in quartz monzonite in a zone 2 miles long and 500 feet wide. Production from the district was reported to have been over 1,000,000 units of W03. Twelve diamond-drill holes, totaling 5,056 feet, were drilled by the Bureau of Mines in the vicinity of the Papoose, Papoose No. 5, Amity, and Union mines, the tailings pond, and the "Old Spud Patch." The work began in August 1943 and was completed in June 1944. This publication briefly describes the history and deposits of the district and gives full details of the work performed by the Bureau.

Jan 1, 1950

By T. R. Rehak

Blasting operations are an essential element in the recovery of our Nation?s mineral resources. The mining industry uses billions of pounds of explosives annually. The majority of blasting occurs in surface mining operations. Blasting results in the fragmentation and often the projection of rocks. Frequently, the rocks are thrown beyond the expected limits. Flyrock and failure to secure the blasting area dominate blasting-related accidents in mining, especially in surface mining. Blasting accidents in the mining industry tend to result in critical injuries or fatalities. Accident reports and information collected from the Mine Safety and Health Administration (MSHA) and other government agencies provide supporting evidence. According to the data collected, blasting-related accidents (in mining) were 11 times more severe than all other types of mining accidents. Blasting accidents are not unique to mining operations - the same situation exists in the construction field. In this paper the authors have compiled a list of the primary causes of flyrock and the failure to secure the blast area. In the next phase of this project, typical blasting scenarios will be reviewed which will highlight the main reasons flyrock and/or lack of blast area security occur. This will alert miners and construction workers to the current problems/hazards associated with blasting and to identify other safety measures to protect personnel.

Jan 1, 2000

By R. R. May

A preliminary examination of the Houston strip-coal mine, situated on the Alaska Railroad at milepost 175 (61 rail miles north of Anchorage, Alaska) and a review of all available information resulting from early coal exploration activities in the area resulted in plans to investigate the coal-bearing formations at depth by means of diamond core drilling to indicate the existence of additional reserves of coal in close proximity to railroad transportation, where it would be quickly available to meet rapidly expanding military and civilian fuel requirements. From the date of mobilization of equipment, August 28, 1951, until date of suspension, August 18, 1952, 2,010 feet of diamond drilling was completed. Ten definable coal beds were cut, of which 2 appear to be persistent and minable over an area of approximately 1/2 square mile. Within this area the 2 minable beds contain approximately 5,000,000 tons of coal in place. Of the remaining beds, at least two others may be minable to the eastward near their projected outcrops; however, these and deeper beds (at least in the vicinity of the drill holes) lie beneath a zone of pressurized gas and brackish water. From a practical standpoint, continued development and utilization of the coal in this vicinity will depend on the operators' ingenuity in developing cheap mining methods and on diligent prospecting for strippable coal under the comparatively light glacial cover.

Jan 1, 1957

By S. P. Howell

"Technical statistical study has been made of accidents in the anthracite region of Pennsylvania in which explosives were involved. The data have been taken from the accident reports in the files of the department of mines of Pennsylvania, supplemented by inquiries in the field.This study has disclosed a wealth of information regarding the nature and the cause of accidents that occurred where different means of firing shots of explosives were employed. In the anthracite region shots are fired with fuse, with squibs, and with electricity,Many of the salient features of this accident experience are illustrated in this report of investigations, and a number of recommendations are made to reduce the hazards of each of these three methods of shot firing.Experience seems to demonstrate that, under conditions in the anthracite region, electric firing of shots is substantially the safest method; that accidents wherein fuse is employed are more frequent than accidents in which electric firing is employed; and that the number of accidents when squibs are employed far exceeds those in which either fuse or electric firing is used."

Mar 1, 1930