Search Documents

By K. Kabezya

A study on slag dispersion in a model of bottom-blown bath smelting converter was undertaken at room temperature. The aim was to investigate the behaviour of the dispersed slag phase at various operating conditions with very high gas flow rates in low slag volume (10%) systems. For simulation purposes water, paraffin-oil, and air were used to represent the bulk steel, molten slag, and gases respectively in a one-fifth cold model of the commercial 100 t Creusot-Loire-Uddeholm (CLU) converter used in the manufacture of stainless steel in South Africa. Dimensional analysis was done to correlate mathematically the dispersed phase holdup with the operating conditions and the modified Froude number. The overall expression of the holdup revealed that the dispersed slag phase decreased with the vertical distance from the original interface between the liquid phases. The dispersed phase also decreased with the radial distance in the water plume zone toward the sidewall. The holdup was apparently much higher on the side of the reactor where there were no tuyeres. The modified Froude number ensured the correlation between the model and the prototype.

Jan 1, 2014

By A. G. Ramsay, P. G. Kahles, L. E. Kun

A method for the clarification of uranium pregnant solutions using a high-rate floc blanket was developed from laboratory scale through pilot-plant testing to full-scale production by the Anglo American Research laboratories. A two-stage clarification process (hopper plus leaf) was commissioned at the Western Deep levels uranium plant in October 1980. The high efficiency of the hopper clarification permitted its use on its own. The leaf clarifiers were therefore taken out of service in September 1981, since when the secondary clarification is achieved by further unaided gravity settling in the semi-clarified and clarified pregnant-solution storage tanks. As a result, a daily 12000 to 17000 t of countercurrent-decantation overflow with a suspended-solids concentration of 500 to 600 mg/I is continuously clarified to a suspended-solids concentration of less than 30 mg/I. Secondary gravity settling reduces the suspendedsolids concentration to under 20 mg/I. The cost of the single-stage hopper-clarification process is RO,O020per ton of liquid treated. The removal of the leaf clarifiers from the circuit resulted in an approximate visible saving of RI00000 per annum.

Jan 1, 1983

1. Book review The geology of some northern Nigerian anorogenic ring complexes, by J.N. Bennet, D.C. Turner, E.C. Ike, and P. Bowden. The British Geological Survey: Overseas Geology and Mineral Resources, no. 61. London, HMSO, 1984. 66 pp. Reviewer: R.H. Ingram 2. Mintek reports Report M226 The separation of tungsten and molybdenum by the formation of sulphide complexes and extraction into a weak-base resin. Report M228 The solvent extraction of zinc, iron, and indium from chloride solutions by neutral organophosphorus compounds. Report M230 Shear flocculation of fines for improved flotation. Report M239 A mineralogical study of residue from the column leaching of a low-grade nickel-copper sulphide ore.3. Recent publication Driger Review, special edition, act. 1985. 48 pp. (Copies obtainable from Roly Nyman, HAMPO PMIE Division, P.O. Box 170, Joham1esburg 2000.) Black Mountain's achievement The 13 689 t consignment of metal concentrate that was loaded aboard the bulk carrier 'George' and shipped out of Saldanha Bay early in December brought the number of tons exported from Black Mountain via the Sishen-Saldanha railway and harbour system to one million.

Jan 1, 1986

Book new a Book reviews Economics of the mineral industries. 4th Edition. Society of Mining Engineers (Caler No. D, Litleton, CO 80127, U.S.A.). 660 pp. Reviewer: M.A. Ford Foundry technology, by P.R. Beeley. Durban, Buterworth Scientific, 1982. R124 + GST. Reviewer: A.P. van Wyk Underground Transport Symposium. Johannesburg, The South African Institute of Mining and Metallurgy Special Publication SP 1. 300 pp. R65 (Non-Member), R55 (Member), + GST. Reviewer: C.L. Workman-navies A summary of the Project DevelopmentSymposium as presented by The Australasian Institute of Mining and Metalurgy. $A 25.00. Reviewer: D.J. van Niekerk Geology of uranium deposits. Proceedings of the CIM-SEG Uranium Symposium, September 1981, edited by T. I. I. Sibbald and W. Petruk. Quebec, The Canadian Institute of Mining and Metallurgy, Special Volume 32, 1985.268 pp. Canadian $40 members, $50 non-members (plus $3 for postage and packaging). Reviewer: M.S. Toros Crushing and grinding process handbook. Chichester (England), Wiley, 1986. £49. Reviewer: M.P. Hay O'okiep's 50th birthday The 0'okiep Copper Company Limited, situated at Nababeep s,ome 35 km from Springbok, recently celebrated its fiftieth anniversary.

Jan 1, 1987

By Z. T. Bieniawski

Estimating the strength of rock materials by Z. T. BIENIAWSKI, Pr.Eng., D.Sc.(Eng.) (Visitor) A practical approach for estimating the strength behaviour of rock materials is presented. The demand for data on rock properties in engineering design is considered, and it is shown that, based on the trends observed in the South African mining industry during the last twenty years, simple and easy-touse methods for the estimation of the uniaxial and triaxial strength of rock materials are needed. It is shown that the uniaxial compressive strength of rock can be conveniently determined from the pointload strength index, which is obtained underground on unprepared rock cores. The triaxial strength of rock can be estimated for most practical purposes from empirical strength criteria. Two such criteria are proposed that allow estimation of the triaxial strength for rock materials to about 10 per cent. The only input required for these criteria is the uniaxial compressive strength. The validity of the practical approach outlined in this paper is confirmed from the experimental tests conducted on some 700 rock specimens representing five rock types. A practical example for the prediction of rock strength is given.

Jan 3, 1974

By S. M. Brabyn

The wear in mild steel pipelines used to convey rod-milled waste backfill was determined and then compared with that obtained using a laboratory rig designed to simulate the wear condition in slurry pipelines. The relative importance of corrosion and abrasion was investigated under various conditions of water quality and particle size distribution. The laboratory rig was then used to evaluate other possible materials of construction for backfill pipelines. A preliminary assessment of the economic viability of pipelines made of alternative materials is included.

Jan 1, 1988

By J. P. Beukes

South Africa holds approximately three-quarters of the world?s viable chromite ore resources and dominates the global production of ferrochrome. Albeit completely unintended, small amounts of Cr(VI) are formed during ferrochrome production. Certain Cr(VI)species are regarded as carcinogenic, hence making the treatment of some ferrochrome waste materials necessary. In this paper, the Cr(VI) treatment strategies currently employed by the South African ferrochrome producers are investigated by means of a literature review and a questionnaire survey. From the discussion, it is evident that various treatment strategies are available to deal with Cr(VI)-containing waste in the ferrochrome industry. However, by far the most commonly applied treatment strategy remains the aqueous reduction of Cr(VI) with ferrous iron. The advantages and the correct application of this strategy, together with the disadvantages and pitfalls, are argued. Innovative improvements on historic practices are also discussed

Jan 1, 2012

By E. Bakhtavar

There are many near-surface deposits with considerable vertical extent that have the potential to be mined by a combined method of open-pit and underground methods. In this regard, there is often a point called ?transition depth? where a decision has to be made whether to continue deepening the pit or change to underground methods. Recently, optimization of the transition from open-pit to underground operation has become an important challenge in mining engineering. Optimally, to model the transition problem on the basis of maximization of the profit from open-pit and underground mining, (0-1) integer programming has been used. In this method, block economic values of open-pit and underground methods should be imported to the transition model. A hypothetical example is presented in order to assess the model in detail.

Jan 1, 2012

EMMES Sampling Conference BACKGROUND & INTRODUCTION ?Impala acquires toll material to supplement production from ROM ?Toll material consists of filter cake, slurry and catalysts ?Samples are collected to determine the commercial values of the lots ?Slurry deliveries projected to remain relatively constant at 120tons dry solids per month, whereas filter cake deliveries set to increase five-fold to 800 tons dry solids per month ?Due to projected increase in toll material, new sampling and offloading facility presently under construction at Impala ?Presentation will cover two projects aimed at reducing the uncertainty associated with sampling of toll deliveries ?i.e. slurries and filter cake.

Jan 1, 2005

By Karl-H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes be-come available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60 %-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as un-economic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid.

Jan 1, 2009

By J. J. Taute, G. Chisakuta, P. Bwando, G. Mitshabu

"BASF Mining Solutions have developed a new generation of copper solvent-extraction reagents that offer significant benefits over the existing reagents available to the industry today. Initial laboratory studies and pilot-plant trials have shown that these new reagents offer the benefits of a dramatic increase in resistance to degradation and are nitration-proof. This paper details a recent pilot-plant campaign at a commercial solvent-extraction plant. The main focus was to evaluate the copper/iron selectivity, copper recovery and net transfer of the new reagent compared with the conventional oxime reagents. The new reagent displays similar copper recovery and net transfer capabilities from typical agitation leach solutions. The pilot-plant results show a step change improvement in copper/iron selectivity in comparison with the existing modified and non-modified hydroxyoxime reagents used on the commercial plant. INTRODUCTION Copper solvent extraction (SX) from an acidic aqueous solution is typically accomplished using a hydroxyoxime extractant (Jergensen, 1999; Kordosky, 2000; Szymanowski, 1993). There are three hydroxyoximes from which all standard formulations are derived: 5-nonyl salicylaldoxime (NSAO), 5-dodecyl salicylaldoxime (DSAO) and 2-hydroxy-5-nonyl acetophenone oxime (HNAO). In the case of NSAO, it is necessary to use equilibrium modifiers in order to increase the copper stripped from the extractant (Kordosky & Virnig, 2003). Blends of DSAO, NSAO and HNAO are used to cover a wide spectrum of conditions (Kordosky, 2008). Use of modified aldoximes and reagent blends over the last 30 years has influenced the way copper producers and equipment manufacturers have approached the operation of copper plants. Existing solvent-extraction reagents cater for typical pregnant leach solutions (PLS) of copper mining systems which do not have significant effects on the reagent. Table I illustrates the range of copper concentration, pH values, temperature and iron concentrations for different leaching operations. As conditions become increasingly aggressive (i.e., higher PLS temperatures in primary sulfide leach or high iron content), current reagents become less capable of functioning according to expectations. One example is the effect of high iron (Fe3+) concentration in PLS and operating SX to achieve high copper recoveries. The ferric is partially chemically extracted and is transferred to elctrowinning (EW) during the stripping stage. To avoid a build-up of iron in electrolyte, which negatively affects current efficiency, a bleed of electrolyte is required. This bleed leads to excessive consumption of reagents, such as cobalt added to the EW process, and thus increases operational cost."

Jan 1, 2015

By L. Linzer, J. Oelofse, T. Rangasamy

Extraction of isolated blocks of ground with elevated levels of stress and/or seismicity is a common occurrence in South African gold mines. Isolated blocks of ground that are divorced from the main orebody and are bound by complex, dip and strike parallel, non-persistent geological structures dominate the Klerksdorp gold fields. No quantifiable methods exist to assess the risk associated with mining these and other classes of remnants. A case history, from a gold mine that planned to extract three remnant blocks hosted in a large complex fault system, is used to illustrate the decision making process based on a combination of underground observations, numerical and seismic techniques. Simple risk estimation matrices were developed and used to estimate remnant-mining risk and finally to quantify the decision on which of the three remnant blocks could be extracted at the lowest possible geo-mechanical risk. Il est courant dans les mines aurifères sud-africaines d’extraire des blocs de terrain isolés qui possèdent des niveaux élevés de contraintes et/ou sismicité. Les régions aurifères de Klerksdorp sont dominées par des blocs de terrain isolés qui sont séparés du gisement principal et qui sont retenus par des structures géologiques non continues, à parallèle de pendage et direction, et complexes. Il n’existe pas de méthodes quantifiables pour évaluer le risque associé à l’extraction de ce genre et autres genres de résidus. Une observation de cas, celle d’une mine d’or qui avait l’intention d’extraire trois blocs de résidus qui se trouvaient dans un grand système complexe de faille, est utilisée pour illustrer le processus décisionnel basé sur une combinaison d’observations souterraines, et de techniques numériques et sismiques. Des matrices simples d’estimation de risque furent développées et utilisées pour estimer le risque lié à l’extraction des résidus et finalement pour quantifier la décision sur lequel des trois blocs de résidus pouvait être exploité au moindre risque géo-mécanique. Die Extraktion isolierter Gesteinsblöcke mit erhöhtem Spannugsniveau oder Seismizität ist in südafrikanischen Goldminen üblich. Isolierte Gesteinsblöcke, die von der Haupterzader getrennt und durch komplexe, parallele abfallende und horizontale nicht persistent geologische Strukturen gebunden sind, beherrschen das Klerksdorp Goldfeld. Es gibt keine quantifizierbare Methoden die das Risiko welches mit dem Abbau dieser und anderer Klassen verbunden ist beschreiben. Eine Fallstudie einer Goldmine, welche die Extraktion von drei in einem großem komplexen Verwerfungssystem eingelagerten Einschlußblöcken plante, wird verwendet um den Entscheidungsprozeß zu illustrieren, der auf einer Kombination von Untertag Beobachtungen und numerischen und seismischen Techniken basiert. Einfache Gefahreinschätzungsmatrizen wurden entwickelt und angewendet um das Abbaurestrisiko abzuschätzen und letztendlich die Entscheidung zu quantifizieren, welcher der drei Einschlußblöcke unter dem niedrigst möglichen geo-mechanischen Risiko extrahiert werden konnte .

Jan 1, 2003

By C. K. Chabedi

"This paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield. The resources occur at a depth greater than 250 m and the thickness of the coal is roughly 110 m, but the top 50 m comprises coal intercalated with shale and the bottom 60 m contains five seams with sandstone and shale partings. Various factors affecting multiple seam mining at these great depths are discussed with reference to lessons learned from local and international experience on multi-seam mining. Field geological and geotechnical data was utilized to assess the stability of the roof of the seams. There is no specific rock mass rating for the Waterberg area, therefore approximate coal mine roof rating (CMRR) values were used to propose appropriate support strategies. Analysis of Multiple Seam Stability (AMSS) was used to analyse the strength of the parting or interburden between the various seams, the mining sequence, and the interaction between the various seams.The research indicated that it is possible to mine seams with a low CMRR at high mining rates using longwall mining, although support for gateroads is expected to be expensive, time-consuming and onerous to install, and will impact gateroad development rates. It will not be possible to simultaneously mine zones in close proximity and failure of the interburden is predicted, thus dangerous mining conditions are anticipated. However, it will be possible to mine just two of the eleven zones using longwall mining. IntroductionThis paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield using bord and pillar and longwall mining. Figure 1 illustrates the location of the Waterberg coalfield relative to other coalfields in South Africa, while Figure 2 shows the areas containing deep and shallow resources. The Waterberg resources are expected to contribute to South Africa’s future energy requirements, and are currently exploited at the Grootegeluk open pit mine. Grootegeluk produces coal mainly for a power station, with the higher quality product supplied as metallurgical coal. The deposit is technically unique and challenging, being a multi-seam coal deposit with a total of 12 seams over a thickness of 110 m as shown in Figure 3, including Zone 5. There is currently limited knowledge on the multi-seam mining of the deep Waterberg resources. Multi-seam mining utilizing the bord and pillar method has been practised in South Africa before, but at a depth of less than 100 m in the Witbank coalfields. Multi-seam mining in thin seams has also been performed in the Natal coalfields at a depth of less than 160 m, but mostly using bord and pillar mining and secondary mining (partial pillar extraction)."

Jan 1, 2016

The Barrick North Mara Mine and the Advanced Systems Group at SGS Minerals collaborated on the implementation of a grinding expert system for the control and optimisation of a single semi autogenous (SAG) mill. Over the last 5 years, grinding expert control has gained wide acceptance by mineral processors. In this paper, two key factors for success are highlighted: the adaptability of the software tools and the interaction with site personnel. Created with SGS?s MET expert console (MEC) toolkit, and running on Gensym?s G2 real time inference software, the North Mara expert logic has been set up to keep a steady and on spec leaching feed slurry while striving to maximize throughput. Leach feed stability was achieved by standardizing operating practices across shifts; a result of successful collaboration with site personnel in developing a consistent control strategy. The strategy maintains the SAG load and power draw in an optimised range by manipulating SAG feed rates and inlet water flow. The project life-cycle was slightly longer than average due to site specific constraints. One of these was the high turnover rate of site?s workforce during the project, coupled with the availability of key staff on site due to the fly in fly out work roster. These constraints called for different, and innovative ways of project commissioning and hand-over. This paper describes details of the control solution, its implementation as well as results and conclusions.

Jan 1, 2009

By Ernst-Ulrich Reuther, Alexander Donmen

Mine ventilation in the German coal mining industry is concerned mainly with problems of thermal environment arising from greater depths and with increasing emission of methane gas. The development of computer techniques over the past ten years for solving these and ancillary problems is reviewed. The emphasis from a planning and control point of view falls mainly on ventilation network calculations, temperature predictions and advance estimates of methane emission.

Jan 1, 2014

By W. J. Whiten

"Models of cone crushers and vibrating screens are described. These models have been constructed from actual plant data using a systematic model-building technique. Included in this technique is regression analysis using multi-dimensional spline functions.The models have been used to simulate complete crushing plants and hence to design and evaluate a control system for crushing plants."

Jan 1, 2014

By M. J. Nicol, R. P. Colborn

An investigation into the kinetics and mechanism of the oxidation of iron (11) by oxygen in aqueous chloride solutions By R. P. COLBORN Pr. Eng., Ph.D. (Natal) and M. J. NICOLt B.Sc. Hons., Ph.D. (Rand) A reaction mechanism for the oxidation of ferrous chloride by molecular oxygen is developed. and the appropriate constants are evaluated. The effect of a number of cations and anions on the rate of oxidation has been tested.

By C Smit

SYNOPSIS A prototype collimated radiometric face scanner was tested in the Harmony Gold Mine. The results obtained during the pilot study indicate that in situ radiometric uranium assays are statistically indistinguishable from those obtained conventionally from channel chip samples. In addition, the study demonstrated that reasonably reliable gold estimates can be deduced from the radiometric measurements, by use of the ratio of gold to uranium within a mine. The instrumentation, calibration procedures, and background determination are described briefly.

Jan 1, 1985

By H. Ruthert

An understanding of wear in systems conveying solids is extremely important from the standpoints of design and economics. The lifetime of any bulk solids-handling system depends on the type of solids present and the operating parameters of the transportation system. The relationship between wear in backfill pipelines on South African gold mines and the transportation system's operating parameters is well understood. However, the effect of the transported solids on the pipe wear is less well understood, because of an inability to characterize particle sharpness. The sharpness of the particles, together with their size and hardness, is responsible for the aggressivity of particles, or their ability to cause damage and wear. This paper presents a novel method for the characterization of particle sharpness. The results presented rank particles according to the sharpness of their surfaces.

Jan 1, 1993

By F. H. Deist, H. D. Small, J. D. Austin, L. F. Duvel

The development and application of a Computer System to aid in the planning of production in mines By F. H. Deist, L. F. Duvel, J. D. Austin, H. D. Small A computer system to aid in the planning of production in mines and its application to a complex colliery are descrIbed, The system consists of three phases, the data base maintenance program the 'production simulator' and the report generation facility, In the first part of the paper the categories of information kept on the data base and the functions of the simulator are described in general terms. The application of the system to a multi-product colliery operating a variety of mining methods in a number of superimposed seams is described m the second part. In conclusion some comments are made on further applications and intended future developments.