Search Documents

By B. Geelhoed

Gy's formula for the variance of the fundamental sampling error (FSE) is based on a model that assumes independent selections of particles. A generalization of this model, which can theoretically lead to more realistic representation of actual sampling processes, was, for the first time, experimentally verified by repeated sampling from a well-mixed batch consisting of particles of zirconium silicate of two different sizes. The predictions for the sampling variance made in Gy?s theory and in the more general model were compared with the experimentally observed sampling variance. During the experiment performed here, the variance prediction made in the theory of Gy ranges from 0.96 × 10?7(g2/g2) to 0.95 × 10?7(g2/g2), which is approximately a factor 60 lower than the experimentally observed variance (5.76 × 10?6(g2/g2)). The difference between the Gy prediction and the experimentally observed variance cannot be fully explained by the uncertainty in the experimentally obtained variance due to the finite number of degrees of freedom. Therefore, the difference is likely to be a significant effect. This shows that, under the experimental conditions, Gy?s formula for the variance of the FSE probably undervalues the sampling variance, unless an empirical correction factor for grouping and segregation is applied in the theory of Gy. The new theory resulted in a variance prediction of 6.00 × 10?6(g2/g2), which is much closer to the observed variance than the Gy prediction. This indicates that the generalization of Gy?s theory offers an outlook for providing a better variance prediction than the Gy predictor in the case of dependencies between particle selections. The results are discussed. Keywords: sampling, variance, parameter for the dependent selection of particles, Gy, experiment.

Jan 1, 2009

By M. Verri

The paper describes the design options available for the simultaneous production of liquid sulphur dioxide, via cryogenic condensation, and sulphuric acid in a sulphur-burning sulphuric acid plant. The impact of the operating conditions of the cryogenic condensation on plant capital and operating costs are discussed, with the main focus on the optimization of the most important economic and operative drivers of the non-ferrous mining industry, such as energy efficiency, reliability, and availability. A case history relevant to an integrated sulphurburning plant producing liquid sulphur dioxide and sulphuric acid, recently started up in the Democratic Republic of Congo, is described. Keywords sulphur burning, sulphuric acid, liquid SO2, cryogenic SO2 condensation, liquid sulphur dioxide, sulphur dioxide.

Aug 1, 2013

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery ? Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery ? Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2012

By T. Szendrei, S. Tose

The fracturing and movement of rock that occurs in the vicinity of a stemmed borehole charge in open pit mining operations are described by examining the effects of the emitted stress waves – shock and elastic – and the expansion of high-pressure detonation product gases. Three principal modes of momentum transfer to fractured rock are identified, all linked to gas expansion work. This work can be delivered radially (burden), axially (stemming), and in the collar zone (cratering). Flyrock is generated under unusual combinations of blast parameters and rock properties. Although infrequent and seldom predictable, the generation of flyrock can nonetheless be interpreted and modelled in terms of the principal mechanisms of rock projection described in this study. The physical processes underlying these principal mechanisms are identified and will permit the development of predictive models for flyrock velocities.

Dec 13, 2023

By J. Loubser

The concept of caring is in most cases confused with material needs and not psychological needs. By giving employees a job, most managers think that employees should be grateful and return the favour by being loyal, productive and working safely. Other managers hold the view that employees can be lucky to have a job. To show and demonstrate that management are caring for the safety of the workforce requires involvement, dedication and commitment. Obtaining the trust and respect of the workforce should be the main thrust of any organization because within trust and respect lie the secret of optimal safety performance. In the last 70 years, all the fatalities and serious injuries that occurred in the mining industry can be traced back to one thing, non-caring. The same safety non-compliances are still observed, reported and planned against as 70 years ago, and strange as it may sound, the same injuries occur the same way. The question could be asked: Does the mining industry need more risk assessments? More codes of conduct? More engineering. Or does the mining industry need more caring?

Jan 1, 2010

By D. H. Diering

Definition of mineral resources and reserves forms the basis for effective mine planning and reliable public reporting of mineral assets. Historically, the mineral resource and reserves declaration process has been the domain of the geology and surveying disciplines, with the declaration of the reserves by the surveyor being based on the application of modifying factors to the declared resources available for mining. As part of an ongoing process to improve efficiency, reliability, and reproducibility of results, this approach has been revised and enhanced through the introduction of a revised process and reconciliation tools. The revised approach to reserve definition is based on the definition of scheduled resources, at an appropriate confidence estimate in the context of an approved business plan, over the anticipated life of the mineral asset being applied to define reserves. This planning and scheduling is developed, during the annual business planning process, by the mine planning department using tools such as CADSMine?. The scheduled area together with the application of revised modifying factors is tabulated in the BME (basic mine equation) and reflects the mine production plan over time. Simplification of the modifying factors to dilution and losses underpins the simple yet robust approach to improved definition of reserves in this process and in the basic resource to reserve equation (BR2RE). Dilution intrinsically affects grade but not metal content, whereas the losses reflect both the efficiency of mining and planning and are reflected in metal losses, area losses, or both. Reconciliation of the derived 'resource converted to reserve' area (which is based on the business plan from CADSMine?) versus the 'resource available for mining' (which is derived from Datamine?) underpins the robustness and auditability of the reserves declaration. This R&R accounting and reconciliation approach is transparent and facilitates interrogation of the logic and rationale of long-term business planning and project strategy. These numbers are processed and reported in the logic of the basic resource equation (BRE), which also addresses aspects such as white areas (future and historic), tail management, and partial extraction (non-scheduled pillars, etc.) in compliance with SAMREC definitions. Areas that do not have the necessary confidence and data support to be declared as resources find their space as pre-resource (outside the domain of public reporting), outlining existing potential for future extraction and reporting. Use of the BRE leads ultimately to a complete, refined accounting and reconciliation-oriented approach for all production entities. The revised resource and reserve process includes the discipline of mine planning as intrinsic to the definition and declaration of resources and reserves. Subsequent to the change in process, the resources and reserves have truly become the domain of the mineral resource management discipline. This paper defines the logic of the basic resource equations and outlines their application in the definition and reconciliation of mineral resources and reserves at Anglo American Platinum Limited.

Jan 1, 2013

By M. Nicolle

The Tati Activox® Project will be the first full-scale implementation of the patented Activox® process (The Tati Activox® project was deferred in 2008. Please refer to the Norilsk Nickel press issue on the topic for more info). The process was developed by Norilsk Process Technology and has been tested on Tati mine sulphide concentrates in laboratory, pilot and demonstration plant scales and demonstrated its viability. There are inherent risks to the final scale-up of the process from the demo plant and one of them will be investigated in this paper. Compartment 1 is designed to leach approximately 77% of the total nickel leached. For this reason agitation requirements in the first compartment of the autoclave are reviewed. An attempt is made to minimize the process and mechanical risks associated in achieving oxygen mass transfer into the slurry solution. The agitator powers for oxygen mass transfer are calculated using empirical correlations and compared to demonstration plant testwork. The resulting gassed power per unit volume (P/V) is higher than most commercial autoclaves and raises uncertainty on the viability of using such high unit power inputs. Additionally, there is concern about the ability of the autoclave shell to withstand and support the higher loading of large agitators. An alternative solution to designing for the increased P/V is assessed in which the number of compartments within the autoclave is reduced from 5 to 4 by removing the compartment wall separating compartments 1 and 2. This results in an enlarged first compartment containing 3 agitators instead of 2. Therefore the compartment 1 oxygen demand is supplied through 3 agitators, which lowers the P/V per agitator. The reduction in the number of autoclave compartments raises the potential for short-circuiting the mean flow pattern by slurry particles. Short-circuiting and low velocity zones could result in a lower recovery of metal and localized hot spots, respectively. A computational fluid dynamic (CFD) analysis was conducted to quantify these concerns and also to evaluate further design considerations. The results indicate that the proposed design change to 4 compartments affects short-circuiting. The impact of increased short-circuiting on the overall autoclave recoveries is not quantified, however; it is expected to be negligible based on testwork done in the Tati Demonstration Plant and similar modifications made to another operating autoclave. The CFD analysis also suggests that there will be no low velocity zones within the compartment.

Jan 1, 2009

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Safety and health can be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard is called AziSA, which means ?to inform? in isiZulu. AziSA provides an architecture that allows for connection of any type of sensor and that is particularly suited to wireless sensing. On the safety side, the CSIR is developing a suite of sensors specifically around the risk of rockfalls. Sensors such as an electronic replacement for the barring tool, or a thermal sensor that can detect loose rock, can already be used to identify potential hazards in the hangingwall. When these sensors are combined with location and time information in a single database, it becomes possible to build maps of risk and to extrapolate risk into unmined areas. It is also easy to confirm that routine safety procedures like barring are actually taking place. In the future, it is proposed that entry inspections will be made using remote techniques that will not place an individual miner at risk. While miners will still be required to bar or place support, they will do so with a clear idea of which portions of the hangingwall are safe, and which present risk. On the health side, if a network such as AziSA is deployed in the stope, it becomes much easier to monitor the condition of individual miners. The work strain experienced by miners can be monitored through heart-rate sensors, and their core body temperature can be monitored using various novel techniques discussed in the paper. Additional sensors can be added to quantify worker exposure to hazards such as noise or dust. Individual sensors allow for people who are at an unacceptably high risk of developing heat disorders to be treated timeously, and they also allow for team management based on objective measures. Over a longer period, position sensing and environment monitors, or personal dosimetry, provide a powerful management tool to prevent workers from being overexposed to hazards, and to confirm that management instructions are being followed. Cost-effective sensing in the stope is a major challenge, but one that can be overcome through technology like that used in AziSA. Sensing provides opportunities both to make immediate interventions when workers are exposed to unacceptable risk, and to manage the long-term exposure of workers to hazard.

Jan 1, 2010

By D. Mjonono, S. T. L. Harrison, N. Maliela, A. Kotsiopoulos

The improvement of coal waste management practices, through the co-disposal of waste rock with sulphur-lean fine waste tailings (<1 mm in size), can potentially mitigate acid rock drainage (ARD). On exposure to natural oxidants, the sulphide compounds present in mine discards generate acidity, creating a cyclical oxidation process intensified by iron and sulphur oxidising microorganisms. To inhibit the emergence of ARD, a stable mine dump may be constructed that is structurally stable and incompressible through the mixing of complementary waste fractions that reduce voids and access to acid generating surfaces. However, large voids manifest as scale increases, due to decreased particle interlock, enabling the unrestricted access of oxidants leading to the early onset of ARD. To avoid this phenomenon, enhanced packing approaches based on geochemical and geotechnical characterisation tests were employed to improve bed stability. These were assessed for long-term prevention using aggressive oxidative conditions typical of heap leaching applications. Favourable results were obtained for both blended and multi-layered systems. However, long-term success was most notable in beds with alternating layers of waste rock and fine waste tailings with co-mingled systems being more susceptible to failure. Deconstructed co-disposed beds provided valuable insight into post-leach structural transformations. Results indicated that relative changes in initial coarse discards to fine waste ratios were most notable in blended systems. Mass fractions of the comparatively more mobile fine wastes increased axially down these test columns that ultimately resulted in increased contact of oxidants with the acid generating waste discards. Conversely, more consistent ratios were observed in multi-layered configurations. In these systems, near impervious hardpans were created by the moisture retaining fine tailings, forming stable structures with neutralising barriers sustained at each alternating layer. Consistent with post-leach geotechnical characteristics, static acid-base accounting tests showed that the uppermost sections of blended systems were more susceptible to oxidation due to structural failure with fine particles migration, while the more stable multi-layered configuration evenly maintained neutralising capacity. Keywords: Acid rock drainage (ARD), bed structure, mobility of fine particles

Jan 1, 2020

By H. Möller, M. Tshibalanganda, C. Taute, A. du Plessis, M. Leary

Additive manufacturing can be used to produce complex and custom geometries, consolidating different parts into one, which in turn reduces the required number of assemblies and allows distributed manufacturing with short lead times. Defects, such as porosity and surface roughness, associated with parts manufactured by laser powder bed fusion, can severely limit industrial application. The effect these defects have on corrosion and hence long-term structural integrity must also be taken into consideration. The aim of this paper is to report on the characterization of porosity in samples produced by laser powder bed fusion, with the differences in porosity induced by changes in the process parameters. The alloy used in this investigation is AlSi10Mg, which is widely used in the aerospace and automotive industries. The sample characteristics, obtained by X-ray tomography, are reported. The design and production of additively manufactured parts can be improved when these defects are better understood.

Apr 1, 2021

By D. Hanekom

Over the past couple of years, Anglo Platinum has made extensive use of technology within the core disciplines (geology, evaluation, survey, and planning) that collectively form part of mineral resource management (MRM). While these technologies were primarily developed to enable geology, evaluation, survey, and planning to carry out their daily tasks, with the main objective of supporting the mine?s production effort, they have also enhanced the disciplines? ability to produce the required outputs within the annual business planning cycle. Anglo Platinum has developed a very comprehensive business planning process, and these technologies play a vital role in enabling both the quality and quantity of inputs into the process, and also the value-add of the final product. This prompted a question regarding the practical application of the CADSMine software. If we changed our thinking in how we applied the software, would it be possible to further improve on the time taken to deliver a business plan? In changing the current planning approach, would we be able to further simplify the process? Is there a way to reduce the data generated in order to enhance the time taken to do reporting, as the CADSMine software is totally network dependent? Less data should equal faster reporting. This paper focuses on the practical application of the CADSMine software, and demonstrates the value-add to the business planning process that can be gained if the mine design methodology is changed from individual panels to bigger blocks representing a raise line.

Jan 1, 2012

By S. W. Jacobsz, E. P. Kearsley, N. K. Schoeman

A physical modelling approach was adopted to simulate the process of cave mining propagation at various horizontal to vertical stress state ratios, and image data was captured and used to characterize the resulting failure mechanisms. Image processing was integrated into the study to determine minor principal strains in models to identify where critical extensional strains had been exceeded relative to crack propagation. The study exhibited a scale factor magnitude of 119 using a calculated critical extensional strain value of 0.014% for the modelling material used. It was perceived that cave propagation occurred through successive parallel extensional ‘fracture bands’ in all cases, as noticed in models of prior studies, deviating from that described by the Duplancic model. Cracks tended to bisect regions of minor principal strain equal to the critical extensional strain, which suggests ‘fracture banding’ is an acceptable failure mode for brittle, rock-like materials. Moreover, it was found that models with lower horizontal to vertical stress ratios (K ratios) showed a greater degree of vertical development of the caving mechanism (at similar vertical stresses), while the vertical extent of the cave was suppressed in models with higher K ratios. Models subjected to larger vertical stresses experienced slower cave formation in latter time-steps. These models exhibited larger two-dimensional caved perimeters and areas, respectively.

Nov 30, 2022

By R. V. Ramani

Managers need quality information for effective decision making. This demand, at the present time, is being fulfilled by the increased use of computers via information systems, decision support systems and management information systems. The idea of incorporating intelligence into computers to aid decision-makers has been evolving for over two decades. In recent years, significant progress is reported on applications to business and sciences. In engineering functions, the Artificial Intelligence approach that seems to have great potential is the application of Knowledge Based Systems. The primary objective of this paper is to identify domains in mining engineering where application of knowledge based systems could be beneficial. In- corporation of the expertise required during the analysis and interpretation stages of an engineering design problem through knowledge based systems is recognized as an area of significant benefit. To this end, the components of knowledge based systems for mine ventilation and strata control design are described. The potential applications and limitations of knowledge based systems are outlined.

Jan 1, 1987

By K. Moxham, B. McKeown

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular orebodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross-cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focused on the haulages and cross-cuts.

Jan 1, 2006

By G. R. Addie

The Hydraulic Institute has completed the task of developing a new ANSI/HI standard 12.1-12.6 (2005) for rotodynamic (centrifugal) slurry pumps covering nomenclature, definitions, applications, and operation. The standard provides examples of the different slurry pump types and contains an extensive section on pump and slurry definitions. The effect of slurry on pump performance is covered along with the pumping of froth. Reference is also made to ANSI/HI standard 9.6.7 (2004), which contains a new method for pump performance correction when handling viscous fluids. Classification of slurry services is established and then is used to determine limitations on velocities and total head per pump in order to obtain acceptable wear performance. The new service class, head per stage and other limits are directly related to capital and other cost considerations that will affect solids transport system economics. The writers review the contents of the new standard, highlight the main points, and discuss the reason for the slurry classification, corresponding limits and expected implications, particularly with respect to operating costs of the pumps in solids transport systems.

Jan 1, 2007

By C. Rodrigues

This investigation compares the gas adsorption behaviour and capacity of three bituminous coals from South Africa, of similar rank, by assessing the characteristics of the raw coal, as well as the resulting float and sink fractions (at 1.80 cm3/g) obtained by density separation of crushed coal samples. Calculations were also made to obtain the raw coal gas storage capacity from the weighted contribution of both float and sink fractions results, thereby permitting comparison with the analysed results of the raw coal. The study demonstrated that the clean fraction of a coal has the highest capacity to retain gas in the sorbed state, followed by raw coal, and lastly the sink fraction, and re?confirmed previous investigations that showed minerals to be inhibitors of gas adsorption and retention.

Jan 1, 2008

By B. Mulcahy, M. Valenta

"The purpose of executing a project in a stagewise fashion is to evaluate all potential options in a cost-effective manner and develop an understanding of the project drivers, thereby minimizing overall project risk to the client. Among the more valuable tools for this exercise are production and financial models that can be used to quantify the sensitivity of the project to the critical parameters.The mine and concentrator used in this case study are located on the Kalahari Copper Belt, which extends from Zambia through northern Botswana into Namibia. This area of Africa has seen very little industrial development and the project will create much-needed employment and development in the region.The success of this project thus far can be attributed to the close cooperation between the geological, mining, and metallurgical disciplines. Regular updates of projected capital and operating cost estimates coupled with project outputs guided the teams in optimizing their various discipline models, ultimately delivering a compelling argument for the execution of the project. Key to the success was the development of a geometallurgical model for the prediction of concentrate tonnage, grade, and recovery for the life of the mine from the mining plan.This paper summarizes the metallurgical findings and the outcome of the various project stages. The development of the model is discussed, as are the challenges faced in developing a suitable metallurgical process route. IntroductionThe Kalahari Copper BeltThe Kalahari Copperbelt, which extends from Zambia across northwest Botswana into Namibia, is considered to be a broad time equivalent of the Central African Copperbelt, with a similar style of mineralization. However, at shallower depths (<25 m), chrysocolla and malachite exist in significant proportions in certain geological areas. As illustrated in Figure 1, the project is located in the Ghanzi-Chobe Fold Belt which forms part of the Kalahari Copper Belt. The Ghanzi Group, which overlies the lowest stratigraphic unit (the Kwebe Formation), consists of three formations, namely the Ngwako Pan, the D’Kar, and the Mamuno Formation (Hall, 2012)."

Jan 1, 2016

By C. I. Ware

The phrase ?back to basics? is used to describe the fundamental principles and philosophies on which a successful mining operation is based. At Richards Bay Minerals (RBM), ?back-to-basics? (BTB) has been implemented as a continuous process to probe operational functions with a view to increase production without capital expenditure. It also ensures that the fundamentals of dredge mining are understood and adhered to. BTB is based on the principle that people drive organizations, necessitating an interactive implementation approach. At the RBM mine this entails a three-pronged approach, namely practical training, teamwork initiatives and the use of lean Six Sigma methodology. It is the latter on which this paper will focus. The lean Six Sigma methodology is successful in identifying, managing and documenting BTB projects, while team work initiatives are integral to successful project implementation. This paper describes two examples of how the Six Sigma methodology can be applied to a dredge mining operation. The first example focuses on the improvement of Mining Pond Echo (MPE) plant throughput by reducing the lost opportunity (non-production) due to tails downtime. The project was successful in increasing plant throughput by 4.5%. This was achieved by increasing the tails disposal system availability by running MPE as a four tails lines operation and focusing on causes of tails production downtime. Subsequently, the tails system at MPE is no longer the production bottleneck. Second, the Six Sigma methodology was successfully applied at Mining Pond Charlie (MPC) to increase the primary dredger throughput by 4.6% through focusing on the dredging technique and maintenance issues. This project highlighted the need for trend analyses to ensure an effective dredging technique, coupled with simple production documentation, which also ensures a focus on maintenance. Keywords: Back to basics, Six Sigma, training, teamwork, throughput improvement, tails, dredger.

Jan 1, 2007

By A. Ndibalema

Blasting is one of the primary functions in any mining operation. Despite the fact that it generally constitutes between 30% to 40% of the mining cost, blasting also affects the cost-effectiveness of down steam activities such as load and haul, safety, tyre life for haul trucks, crushing and milling. Over the past three decades, significant progress has been made in the development of new technology in an attempt to reduce costs and increase efficiencies and productivities of blasting activities. Mine to mill project concepts have paved the way for such developments. Other advancements have included sophisticated computer modelling technologies for blast design and performance analysis. There are many factors that affect the cost of blasting. These can be divided into two categories; controllable and uncontrollable. The latter includes costs related to depreciation, exchange rates and government legislation with the former category including contractor versus owner blasting costs, efficiency and productivity issues and product quality. Controllable factors have one common denominator which can determine their outcome; direct site management influence. Excavator digging rates and final floor conditions give a good measure of blasting performance, and alternatively cost effectiveness. This paper is aimed at benchmarking against a blast optimisation database, understanding the relationship between costs and identifying opportunities for improvement. Understanding the cost drivers allowed a typical cost model to be developed for the current mining operation at Geita and this was used to drive continuous improvement with emphasis on closing the information loop.

Jan 1, 2008

By S. Kahraman

The prediction of rock properties from indirect testing methods is important, particularly for preliminary investigations since indirect tests are easier and cheaper than the direct tests. In this study, we investigate the predictability of the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of rocks from the indentation hardness index (IHI) obtained using point load apparatus. Forty-six different rock types, 14 of which were igneous, 15 were metamorphic, and 17 were sedimentary were tested in the laboratory. The UCS and BTS values were correlated with the corresponding IHI values and the results were statistically analysed. The influence of rock classes on the relationships was also investigated. A strong correlation between UCS and IHI was found for all data. The correlation between BTS and IHI is not as strong as the correlation between UCS and IHI, However, it is in the acceptable limits. When the regression analyses were repeated for igneous, metamorphic, and sedimentary rocks, the correlation coefficients were generally increased. The results show the UCS and BTS can be estimated from IHI, In addition, the effect of rock classes on the relationships between IHI and both UCS and BTS is important.

Jan 1, 2012