Search Documents

By W. O. Ortlepp

This note considers the most fundamental concepts of support design for deep underground openings and discusses them briefly in the context of tabular stoping and deep hard-rock tunnelling. It concludes that the conventional re-bar, mesh, and lacing methods that have been widely used in deep gold mines are quite inappropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit.

Jan 1, 1995

By H. Wagner

The paper points out that bord-and-pillar mining is the most important method of coal extraction in South African underground coal mines, and advocates that pillar design procedures should be refined to make more rational allowance for the differences in strength properties between various coal seams and roof and floor strata. However, any deviations from well-established design procedures must be based on sound engineering principles and reliable data on the strength properties of the seams and strata concerned. Recent information indicates that practices for the protection of surface structures against underground mining should be revised.

Jan 1, 1980

By J. D. Wells

An account is given of the planning required for the rehabilitation of land that is to be disturbed by opencast mining, and of the preparation of rehabilitation of land that is to the Inspector of Mines. The plans Include the provisions that are to be made to allow for climatic conditions, land use, vegetation and wildlife, surface-water resources, geology and ground water, soils, land capability, rehabilitation method, location of discard dumps and slurry ponds, pollution control, and costs. . . Monitoring of the operation is the only way that the rehabilitation plan can be improved, and both monitoring and planning are essential when provision is being made for the closure of a mine.

Jan 1, 1986

By D. R. Hardman

Coal mining has been practised in South Africa for over one hundred years. The total production increased gradually in the early pat of the twentieth century, but over the past twenty years the rate of growth has been considerable. Although opencast mining has contributed largely to this increase in production in recent years, underground bordand- pillar operations still contribute slightly less than 50 per cent of the total production. The paper highlights problems arising from old bord-and-pillar workings, and an indication is given of how some of the problems have been addressed.

Jan 1, 1990

The paper discusses some theoretical aspects of Gy's sampling theory and provides reasons as to why it has found limited use in the mining industry, particularly for ores with low concentrations of values such as gold. These types of ores are referred to as low grade ores in the paper. It is shown that the misuse of the a priori liberation factor proposed by Gy is the main reason for the implementation limitation of Gy's model for low-grade ores. In addition, results of a case study done at the Gencor Geostatistics Department based On the new implementation of Gy's theory are provided.

Jan 1, 1996

By K. E. Mantell

1. TRACKLESS MINING AT OAMITES by K. E. MANTELL Oamites Mine, brought into production in late 1971, is located 50 km south of Windhoek, South West Africa, on the northern boundary of and just outside the Rehoboth Gebied. Oamites was known as a possible mining proposition at the turn of the century when Hanseatische Minen Gesellschaft was adit mining on the adjacent farm Kamzwas. Rand Mines Limited carried out a small amount of prospecting in the early 1960s, Falconbridge Explorations Limited later taking over the prospect. Approximately 4600 m of diamond drilling was carried out between 1965 and 1967.

By M. J. Daly

Historically, engineers and scientists, particularly those involved in the coal-mining industry, have been slow to adopt statistical methods. However, the need to obtain the maximum information .from expensive exploration and development programmes, and the current focus on total quality management, have led to a change in perceptions if classical statistical and geostatistical methods and their application as planning tools. Some if the underlying issues associated with the generally poor communications between statisticians and engineers/physical scientists, which contribute to some if the misconceptions relating to statistical methods, are discussed The potentially profitable application if a number if statistical techniques in the fields if geological evaluation and mine planning! development is also reviewed, with specific reference to the coal industry.

Jan 1, 1995

By D. A. Fenton

The structural design of large grinding mills, with reference to shell-mounted bearings by D. A. FENTON*, P. Eng. (Visitor) The paper outlines the advantages of shell-mounted grinding mills over mills having a conventional trunnionsupported shell. The growing use of larger mills in the past decade has led to a significant number of mechanical and structural failures, the most common being those at the junction of the head and the shell. Larger mill diameters favour the use of shell-mounted bearings. The elimination of castings, which have an inherent weakness to fracture, makes the shell-supported mill lighter and stronger than a conventional mill of the same shell thickness.

Jan 9, 1976

The increasing transportation of solids by pipeline, in South Africa and internationally, replacing the conventional transportation methods of rail, road, and conveyors, has resulted in much research into this area of solids transportation. Pipeline wear continues to be an area of specific concern, since it constitutes a major cost during the life of a pipeline installation. Wear data from an accelerated wear test and actual pipeline tests are presented. Trends in the performance of the pipeline materials tested are discussed, and possible solutions to the problem of pipeline wear are presented.

Jan 1, 1992

By L. Woollacott, R. P. King

Although several models for the carbon-in-pulp (CIP) or carbon-in-leach (CIL) processes have been published, most of these models do not consider in detail the way in which the carbon phase flows on large-scale plants. This paper illustrates the importance of these details if the CIP or CIL process is to be modeled correctly. An appropriate model, based on population-balance techniques, is then derived. Suitable mathematical techniques for the solution of the model equations are also described. Finally, a method for estimating the model parameters for a full-scale plant is described.

Jan 1, 1990

By R. C. Urquhart, W. P. Channon, D. D. Howat

Discussion: The mode of current transfer between electrode and slag in the submBerged-arc furnace by w. P. CHANNON, R. C. URQUHART, and D. D. HOWAT J. MEINTJES I have read the paper with much interest, and I should like to make a few observations. (I) The experimental work deals with resistance heating by an electrode immersed in a slag... AUTHORS' REPLY We thank Mr Meintjes for his critical analysis and helpful comments arising out of his study of our paper. Possibly we should emphasize at the outset that our experiments all related to the conditions in which the lower portion of the electrode was immersed in molten slag. We believe, however,

Jan 12, 1974

Measurements of the rates of penetration at various throttle air pressures are presented as a function of thrust for three different rockdrills when drilling quartzites with strengths of 45 000 lb/in2 and 39 000 lb/in2, The rate of penetration at optimum thrust is shown to agree well with the predictions of theory and curves of air consumption as a function of throttle air pressure are presented. Man-held machines are shown to be under-thrusted at throttle air pressures above 40 lb/in2g. Measurements of bit wear as a function of distance drilled are presented graphically and discussed in terms of the theory developed in Part 1.

By G. P. N. Venter

A method of evaluating the possible effect of an industry on the environment is presented, and the method is illustrated by its application to a hypothetical problem. An analysis is offered based on an actual survey of four industrial sites in the Lydenburg area of the eastern Transvaal. The survey showed that there is a high incidence of potentially unfavourable conditions, and there is a distinct possibility that a topographically induced eddying motion will extend over the town and the industrial sites. This moving air could entrap air pollutants, resulting in high concentrations of pollutants over the town. It is concluded that none of the sites is suitable for industries that pollute the atmosphere.

Jan 1, 1978

By J. A. C. Diering

The determination of stresses and displacements close to tabular excavations is of considerable importance in the planning of tunnels and of remnant and pillar layouts. This paper gives a description of a simple yet effective method for the achievement of improved values from an analogue or MINSIM type of analysis. Essentially, closures and rides (the movement of hanging-wall relative to footwall) in mined-out areas are assumed to vary in a piecewise linear fashion as opposed to a piecewise constant fashion. As the former fashion more closely resembles the true variation, it is possible for the stresses and displacements at points close to the excavations to be calculated with much better accuracy.

Jan 1, 1980

By J. L. Taylor, E. N. Lawson, Hulse. G. A.

It is generally recognized that a large proportion of the gold remaining in the residues from metallurgical plants on the Witwatersrand is occluded in pyrite. The conventional flotation-roasting process typically recovers approximately 40 per cent of this gold. The process described here is an unconventional route involving bacterial oxidation, which can achieve a gold recovery of approximately80 per cent. The paper describes tests carried out in the laboratory, as well as on a slimes dam. The results show that recovery of gold can be noticeably enhanced through the use of bacteria under conditions of controlled pH, moisture, and aeration. Biological oxidation of the pyrite releases the occluded gold, which then becomes amenable cyanidation.

Jan 1, 1990

By G. Matheron

This paper discusses important aspects, both psychological and methodological, which have delayed the introduction of geostatistics in practice. The evolution of geostatistics is traced through three 'generations', and in conclusion some important questions are raised on the current status of the subject and possible areas of future research.

Jan 1, 1987

By J. A. Ryder, M. U. Ozbay

An ERR-based methodology is presented for use in the re-assessment of the performance of stabilizing pillars, taking into account the effects of fracturing that can occur in pillar foundations under conditions of high stress. It is shown that the damage in the foundations of under-designed pillars can cause up to 30 per cent increases in ERR compared with the ERR for pillars with unfractured foundations. Despite this reduction in assessed performance, stabilizing pillars are still generally found to result in substantially lower ERR levels than alternative methods of reducing ERR, such as the use of stiff backfill or backfill ribs.

Jan 1, 1990

By M. B. Cortie, J. H. Potgieter

An account is given of the production of three types of experimental high-chromium duplex stainless steel. The alloys had chromium contents of 22, 29, and 35 per cent. The partitioning of the main alloying elements between the austenite and ferite phases was determined, and the effect of the alloying elements chromium, nickel, and molybdenum on the mechanical properties and corrosion resistance of the duplex stainless steels is summarized. The phase compositions of the different duplex stainless steels were measured by different techniques, and the values obtained were correlated. The cracking occasionally observed during the thermo mechanical processing of these alloys was studied, and is explained as being the result of known embritlement processes.

Jan 1, 1990

By R. A. Plumbridge

I am deeply honoured by your invitation to address your great Institute on this centenary occasion. Mining is a cyclic industry that continuously faces enormous challenges as it wrests the treasures of the earth from an often reluctant mother nature. Throughout the ages, those challenges have demanded great skill from mining men and women, who are required to blend a mixture of robust determination with art and science. Pioneer Miners and Scientists It is not surprising therefore that the first blush of euphoria surrounding the discovery of gold on the Witwatersrand quickly gave way to consternation about the need to increase the metallurgical recovery of gold from the then readily identifiable conglomerate. The rugged pioneer miners had to turn to scientists for their salvation.

Jan 1, 1994

By M. Reuter

This paper gives an overview of some criteria for the selection of processes for the recovery of lead and zinc from various raw materials and/or intermediate products. A glossary of possible processes and process variants, is presented and discussed, as well as the way in which these are interlinked. Recent developments in metallurgical process synthesis are also discussed, and the results produced by an eco-techno-.economic synthesis procedure for process routes in zinc metallurgy are given briefly. The way in which such a synthesis can complement a life-cycle assessment (LCA) of zinc-producing technologies is also described.

Jan 1, 1997