Search Documents

By J. Talja

Keywords: drying, steam drying, concentrates, copper, lead During the past twenty years steam drying has become a prominent technology for drying of non-ferrous metals concentrate. This is mainly because of its low energy consumption and very low emissions. The first applications of significant capacity were stationary steam dryers, which however, faced severe challenges in maintenance costs and availability. That technology was soon replaced by Kumera?s rotary steam drying technology, which has been the dominant technology in new dryer installations world-wide for the past ten years, ever since the first installation in Hamburg in 1999. There are ten Kumera steam dryers in operation today and five more to be commissioned during 2011. Practically every dryer is different owing to continuous development, new innovations and operational experience with continuous feedback from the operators. Most significant improvements relate to capacity increase with the Kumera steam-dryer family, new feeder systems at the wet end, a completely new design of the dry material discharge with increased availability, heating element design and material selection, and control systems. This paper discusses the modifications and improvements introduced which have enabled the Kumera steam dryer to become the global leader in new dryer installations.

Jan 1, 2011

By Merete Tangstad, Kai Tang

The primary aim of the present investigation is to develop a model which permits to calculate/predict the viscosities of ferromanganese slags, typically focus on the MnO-SiO2-Al2O3-CaO-MgO-FeO multicomponent system. The present viscosity model emphasizes the ability of prediction, i.e. using the binary parameters to extrapolate the viscosities in ternary and higher order systems. To this end, a physical sound model is essential. Temperature dependence of viscosity is described by the Eyring?s formalism. The well-known cell model is used to define the SiO44- tetrahedra in the silicate melts. Composition dependence is expressed in term of viscous activation energy, which is characterized by the binary structural units. The viscosities in ternary and higher order systems are hence predicted using the binary activation parameters. The model has been used to calculate the viscosities in the whole liquid composition range of ferromanganese slag.

Jan 1, 2007

A number of impending and actual pit wall failures have been observed and documented, which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

By R. Pickering

The purpose of this paper is to explore the application of technology to stoping systems. Technology, because for the past 100 years the South African narrow reef mining industry has battled to control working costs in a labour-intensive industry. Stoping systems, because it is the stoping method and methodology which is at the heart of the mining system. Introduce a more efficient stoping system and the mining system will look after itself. The technology applied to stoping over the past 100 years can be categorized as follows: ?The introduction of pneumatic rockdrills early this century, the cumbersome rig mounted units being replaced by smaller, lighter hand-held units which were then made easier to use with the addition of an air leg ?Scraper winches to replace gravity and shovels to move rock both in the face and the gullies were first introduced in the late 1920s ?Hydraulic props as a support method arrived in the1960s ?Some people argue that tungsten carbide inserts were equally important. There have been a number of attempts to introduce different technologies into stoping, the most recent being trackless equipment. Where the stoping layout suits the technology it has been successful. There have been too many instances where a technology has been installed because it is fashionable. At the end of the day the outcome from change in the stoping systems has to be safer and more profitable mining systems. It is the contention of the author that change is only likely to be effective if it is supported by the introduction and application of appropriate technology.

Jan 1, 1999

By J. F. Curtis

In the synopsis, the author concludes that ?high levels of seismicity do not coincide with high rockburst rates?. Implicit to an appreciation of this statement is the necessity of a common understanding of what is understood by the terms: ?high level of seismicity? and ?high rockburst rates?. With respect to the former term there is no difficulty in that the level of seismicity is traditionally measured in terms of the Richter Scale. The latter term however presents a problem in that the author defines it as a particular sort of seismic event?viz: ?Rockburst? is understood as a seismic event that causes damage to an underground excavation with subsequent injury, loss of material/equipment or production shifts? (p. 322). No scale is given of the amount of: ?excavation damage ?level of injury ?material/equipment loss ?production shifts lost whether separate or cumulative, for a particular seismic event to be classified as a rockburst. A further difficulty arises in that in common usage the words ?rockburst?, ?seismic event? and ?earthquake? are all used to describe the same event.

Jan 1, 1999

Recently, work was carried out by the Shotcrete Working Group to study anisotropy in steel fibre reinforced shotcrete using strain-controlled, compressive strength testing methods. The shotcrete materials used and specimen preparation procedures as well as testing methods are described. The test results are discussed and it is concluded that, because of the anisotropic nature of fibre reinforced shotcrete, it may be worthwhile investigating the degree of such anisotropy in practice using strain-controlled, strength testing techniques.

Jan 1, 2001

By B. M. Nyombolo

The interest shown in our paper by Drs Schaekers and Dew, and their favourable comments, are appreciated. However, some of their remarks require a response. Stability testing procedures Regarding the issue of stability-testing procedures, we concur that no long-term procedure has been accepted by either environmentalists or the mining/processing industry as a valid method to test the long-term stability of solid wastes. We agree that the method we used is no exception, and we certainly did not claim that it should be recognized as such. What we did attempt to portray was that we had designed the test procedure in an attempt to simulate, at a very small scale, a tailings dam environment.

Jan 1, 2001

By C. Sensogut

The phenomenon of spontaneous combustion is one of the major hazards encountered in underground coal mines both from the safety aspects and on economic grounds. Every occurrence, however small, if not tackled effectively in the early stages can develop into open fire, or explosion of gas or coal dust. In terms of economy, even dealing with small incidents may be costly in terms of labour and materials, and in case of a sealing off of a district being necessitated, the loss of face equipment and sterilization of reserves is potentially great. Therefore, expense and effort in prevention and detection of such heating, together with a high state of readiness for dealing with likely event, is completely justified and may be considered as a sound investment. In order to achieve this investment, it may be worth to pinpoint the centre of the fire occurring due to autogenously heating which is supposed to be great assistance to inert it at a least cost and time. Therefore, it is the aim of this work to model the spontaneous combustion in the goaf.

Jan 1, 2002

Outsourcing of specialist and non-continuous services is common practice in international mining operations. There is an increasing trend towards this practice in South Africa as a result of the major organisational changes that have taken place in the industry, and as lower revenues and production cost pressures have reduced profit margins. Many specialist functions have been outsourced in the industry for a long time, an example being shaft sinking, which is undertaken by specialist shaft sinking contractors. In the professional services area, some activities have been outsourced, for example the design and construction supervision of tailings dams, but mining related activities such as geology, mine planning and scheduling, engineering, ventilation, and rock engineering, have traditionally been carried out by in-house staff. In this paper some of the industry problems which have led to an increase in outsourcing of professional services are considered. Then the pros and cons of outsourcing are dealt with before outlining the factors which should be taken into account in choosing an outsourcing partner.

Jan 1, 1999

By A. Haines, O. Varaud, I. Baidoo

Abosso Goldfields Limited (AGL) is in the process of developing an expansion of their Damang Open Pit gold mine in Ghana. AGL acquired the Damang mine in January 2002, with SRK participating in the geotechnical investigation and design for the project since 2001. A deep resource drilling program, completed during 2004, intersected an extension of the orebody below the then planned final pit floor. A feasibility study has been completed to determine the economic extraction of this deep ore with an expanded pit shell. The Damang mine is in a stockwork sulphide deposit at the culmination of the Damang anticline. The deposit occurs as hydrothermal mineralisation associated with dominantly east dipping thrusts and sub-horizontal quartz veins. Primary gold mineralisation also occurs in the conglomerates of the Tarkwaian Formation. The geological units consist of steep easterly dipping dolerite, sandstone, siltstone and phyllite beds, with the weathering profile comprising saprolites overlying a relatively thin joint oxidized horizon. It is planned to deepen the current open pit to a final depth of up to 270 m, primarily by the development of a push-back of the eastern and western walls. The edge of the Eastern Tailings Storage Facility (ETSF) is currently located within 80 to 100 m of the crest of the existing pit. The geotechnical design focused on the optimization of the bench face angle and finally recommended a ?Steep Slope Strategy?, involving 24m high near vertical benches. Limiting bench stack heights of 96m at a maximum of 66° were derived from the influence of major structures and the variation in rock mass conditions. The overall slope angles in each pit sector were developed around the requirement for haulage ramps. One of the main design challenges was to optimise the standoff distance between the final pit crest and the ETSF. This process had to consider maximum access to the resource without undue influence on or from the nearby tailings dam. A planned increase to the height of the dam wall was an additional factor in the design. Dewatering of the pit walls was also a major consideration in this tropical environment.

Jan 1, 2006

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004

By F. Peer

In most coal preparation processes, water is a necessary medium, but the presence of water in coal after it has been cleaned has a negative impact on transportation costs, handling and specific energy values. The utilization of super absorbent polymers (SAP) in the nappy application is well known. The concept of utilizing these polymers was investigated for the purposes of dewatering coal and other fines, generated by preparation processes such as flotation. SAPs are granular highly cross-linked synthetic copolymers with excellent water-absorbing properties. The dewatering process is characterized by three main stages: (a) contact of super absorbent polymer with high-moisture fine coal; (b) separation of dewatered fine coal from super absorbent polymer; and (c) regeneration of used super absorbent polymer, by exploiting its response to changes in conditions such as pH or temperature. Preliminary tests showed the separation step to be very difficult. The novel idea of encasing a given amount of polymer in a water permeable cloth solved this problem (of separating the swollen polymer from the dewatered coal). Preliminary tests investigating the effectiveness of the sachets of polymer showed a drastic decrease in the moisture contents of slurries. Furthermore, it was shown that it was possible to regenerate the polymer (still within the sachets) through thermal drying. A full-scale experimental programme was then followed to accurately determine the feasibility of using sachets of SAP. The experimental variables were initial slurry moisture content and polymer dosage. It was observed that the sachets seemed to work fastest and most effectively at high moistures and also at higher dosages of SAP. Regeneration of the polymer was also investigated, using two methods: thermal regeneration and pH-induced regeneration. The experimental variables, for investigating the regeneration process, were method of regeneration and grade of water used. Thermal regeneration at 70°C seemed to work successfully. Although the cost of using thermal energy is still a problem, the safety aspect (fire hazards) has been addressed since the polymer does not ignite when heated, unlike fine coal particles that may do so. The alternative method of regeneration, which exploits the pH-sensitivity of the polymer, was less successful, and further work needs to be conducted.

Jan 1, 2003

By E. Snyders

The upgrading process of an inferior grade of zircon to a superior opacifier for ceramic applications was investigated. A calcining process in the presence of mineralizers was used to produce the product in a conventional muffle furnace. A pre-milled inferior grade zircon concentrate, with a relatively high iron and alumina content generally not suitable for high quality ceramic applications, was used in this study. The influence of the upgrading process on the opacifying properties of the zircon material was compared to that of commercially available prime grade zircon opacifier products currently being produced in South Africa. The influence of a calcining step in the presence of mineralizers with regard to the milling characteristics of the treated zircon material was also evaluated in this study. The morphology of the treated and untreated zircon opacifier samples were investigated by SEM micrographs and the colours of zircon samples were characterized on the grounds of the Commission Internationale de l`Eclairage (CIE) standard procedure (CIE L* a* b* measurements) after application on a bisque ceramic tile. It was found that the treatment improved both the milling as well as the opacifying properties of the treated inferior grade zircon concentrate and renders it equivalent to or better than prime grade zircon opacacifiers currently produced. Keywords: ZrSiO4; opacifier; colour; milling; calcining.

Jan 1, 2005

By K D. Wilkes

The WEMCO Heavy Media Drum Separator was first introduced by WEMCO in California in the 1940`s, initially from their base in San Francisco and later when the company moved to Sacramento. The WEMCO Company became a part of EIMCO Process Equipment in 1985, and in 2002 EIMCO became a part of the GL&V Group when Dorr-Oliver EIMCO was created. Throughout this period of time the WEMCO Drum has been installed on a variety of different applications and is now operating at the heart of many of the world?s largest Minerals and Coal Processing Plants, as well as being used by many smaller producers and metal re-cycling operations. This paper looks at the practical aspects of using WEMCO Drums in a representative range of processing applications.

Jan 1, 2006

By W. Pulles

Mining can adversely affect water quality and poses a significant risk to South Africa?s water resources. Proactive management of environmental impacts is required from the outset of mining activities in order to reduce this risk. Major strides have been made over the last 7 to 8 years, by both the Department of Water Affairs & Forestry (DWAF) and the mining industry, in developing strategies and management plans for the effective management of water within the industry. This has largely been achieved through the development of joint structures where problems have been discussed and addressed through cooperation. This process, which was started around 1991, has continued through to the present time. The mining sector management strategy has been developed at a number of different levels as follows: ?A detailed Management Plan, that sets out strategic objectives, broad strategies and functional and organizational arrangements. ?Operational Guidelines, that define and document specific operational procedures. ?Technical Guidelines, that define and document best practices for pollution prevention and impact minimization from mining operations. The Technical Guidelines consist of Best Practice Guidelines (BPGs) and Regulations.

Jan 1, 1999

By N. Mphathiwa

When slope angles are designed during open pit optimization, there is a risk factor applied in steepening the slopes. The steepening of slope angles has implications for the safety and economics of the mining operation. The steeper the slope angles, the greater the probability of slope failure. Although a slope failure will result in added costs, the challenge is to compile an accurate cost-benefit exercise optimizing the economic benefits of the project without exposing mine workers and equipment to unacceptable risk of rockfalls. A balance between the safety of the operation and the economics of the investment is therefore required. The ideal situation is to have a slope monitoring system that will predict slope failure by detecting any ground movement before the actual failure occurs. This early warning will allow the risk factor to be applied with a high degree of confidence, knowing that the risk will be adequately mitigated. The objective of this paper is to provide guidelines on how to design an optimal survey slope monitoring system. It is the authors? view that for a survey monitoring system to yield desirable results, it should adhere to survey principles such as working from the whole to part and consistently cross-checking. The case study used is Jwaneng Mine, and the design strategy outlined can be used as a guideline for developing a new slope monitoring system or to optimize an existing one.

Jan 1, 2014

By G. V. R. Landman

In the early days of underground coal mining, the use of explosives to break coal resulted in a large number of disastrous methane and coal dust explosions and consequential loss of life. Research by the British, French, US authorities, amongst others, introduced many practices that significantly reduced the occurrence of such incidences. The use of explosives designed to be safe in a methane atmosphere, plus the creation of a second free face were two such practices which became commonly used in coal mines all over the world including southern Africa. With its associated coal cutting equipment and labour, the cost of creating a second free face is significant and this, together with the constant drive to reduce mining costs in a competitive market, causes mine management to regularly question the need for the second free face. Also, the safety and nature of permitted explosives has changed considerably since the days of black powder and nitroglycerine-based explosives with the introduction of water-based explosives. In southern Africa mining regulations pertaining to the blasting of coal has its origins in British research which was largely done in the first half of the twentieth century. More recent research by the US Bureau of Mine has resulted in a deeper understanding of some of the mechanisms of methane ignition by explosives and suggests that some of the earlier regulations can be relaxed to a certain extent without compromising safety. This paper gives an overview of the original research done in Europe and the more recent work in the USA, to give mine management and regulatory authorities a deeper understanding of the important safety issues when using explosives in a methane atmosphere. It also suggests that blasting off the solid is no less safe than using a second free face providing certain safety procedures are followed.

Jan 1, 2000

By R. C. D. Phillis

Conventional stoping in hard rock mining is largely considered an operational environment. This paper suggests that stoping falls within the realm of a project management environment typified by uncertainty, variation, and large numbers of interdependencies. Stoping was then equated to a micro-project with many simultaneous activities that had to be executed accurately using finite resources within limited shift durations in order to reach specific goals. Critical chain project management (CCPM) principles were applied to the stoping activities, and the results showed that the number of blasts per panel can be significantly increased by successfully moving the distribution of work as close as possible to the start of shift. Critical chain principles also assisted in facilitating re-focusing and teamwork among stoping crews as well as between day- and night-shift crews. The main recorded success was in managing inherent protective capacities/local contingencies/fat/buffers that are found in all projects. The impact on mine health and safety (MHS) was significant as individual operators and crews became convinced that they could perform all stoping tasks (activities) without compromising accuracy or speed.

Jan 1, 2011

By G. B. Quaye

The deep level gold mining environment is characterized by high stresses that give rise to intense mining induced fracturing of the rock mass surrounding the stopes. In a geologically disturbed region where the intensity of mining induced stress fracturing is high, the degree of faulting and/or the frequency of other geological features such as joints may pose serious strata control problems. Unfavourable intersection of these discontinuities namely, faults, joints and mining induced stress fractures tend to divide the immediate hangingwall into unstable keyblocks which, if not supported, may result in extensive falls of ground. Effective support strategies therefore demand detailed investigation of the predominant inclinations and orientations of these discontinuities. The orientations and inclinations of these discontinuities surrounding a deep level stope have been measured. The results are projected onto the lower hemisphere of a stereographic net to determine the factors that contribute to the falls of ground in the stope. The analyses reveal that unfavourable intersection of these discontinuities divides the immediate hangingwall into unstable wedges that may become dislodged between support units.

Jan 1, 1998

By K. Osburn

South Deep Gold Mine, owned by Gold Fields Ltd., is situated near Westonaria in the Gauteng Province of South Africa and mines the conglomerate bands of the Upper Elsburg reefs (Mondeor Conglomerate Formation) of the Witwatersrand Supergroup and the Ventersdorp Contact Reef (VCR) of the Ventersdorp Supergroup. The stoping and underground developments are mechanized. The Upper Elsburg reefs are mined by a variety of mining methods, including mechanized drift and fill, modified drift and bench, longhole stoping, and low-profile mining. Optimal mine design and scheduling for deep-level mechanized mining are complex, and success is highly dependent on detailed, robust, and accurate geological and geostatistical models. Geological structures significantly influence the sedimentological characteristics, distribution, and preservation of the Upper Elsburg reefs and VCR. Accordingly, particular emphasis is placed on the generation of a mine-scale structural model that accommodates the relationships between the older north-trending fault systems (West Rand and Panvlakte faults) and younger east-trending dextral wrench faults. Results from underground mapping, borehole intersections, and highresolution three-dimensional seismic data have been integrated to produce coherent three-dimensional geological models. The Upper Elsburg reefs suboutcrop against the VCR and comprise an easterly diverging clastic wedge, thickening from the suboutcrop position, to approximately 130 m at the mine?s eastern boundary. The Upper Elsburg reefs are characterized by conglomerate and quartzite bands forming multiple, stacked, upward-fining unconformity-bounded couplets. Palaeocurrent directions are dominantly from west-northwest to east-southeast, indicating that the more proximal deposits are preserved close to the suboutcrop, with distal facies to the east. Sedimentological modelling is applied to individual stratigraphic units and caters for facies definition. This is achieved through channel width (CW) kriging and fitting of type sections to borehole and mapping data. Homogenous geological geozones for each stratigraphic unit are thus defined within individual structural blocks on the basis of those sedimentological parameters that have been found to have a positive spatial correlation to gold concentration. These geozones then serve as constraints to the evaluation of the orebody. This contribution presents a summary of the modelling processes that are currently applied in the development of high-confidence, timeously produced geological models that are essential input for mineral resource estimation and mechanized mine planning and scheduling.

Jan 1, 2014