Search Documents

By Davidtz. John C.

INTRODUCTION The effectiveness of collector type on sulfide mineral flotation is generally determined by the amount and type of functional groups of collector molecules that interact with surface and water at the mineral/collector/water/gas interface. The final interfacial state when bubble contact takes place is preceded by chemical and physical reactions that involve these gas/liquid/solid interactions. These interactions differ not only for different minerals, solution and gas composition, but also for different collector molecules. The purpose of this paper is primarily to summarize the developments and status of short (C2-C6) and long (C12) chain, aliphatic collectors that contain three sulfur atoms in their polar function. These are trithiocarbonates (TT'Cs). For purposes of comparison, similarities in molecules containing 0, N and S are compared. Mostly short chain ionic collectors molecules of dithiocarbonates (DTCs) and TT'Cs were compared. The studies, largely bench scale flotation and plant testing, were carried out on ores containing Cu, Ni, Au, and PGM's. Studies of long chain 'ITC collectors are reported on Ni, PGM and auriferous pyrite ores containing uranium. Under starvation dosage conditions, surface activity coefficients of short chain collector molecules and interacting water were calculated. Based on the UNIFAC group contribution method of activity coefficient calculations, the Gibbs Excess Free Energy

Jan 1, 2005

By D. L. Purcell, B. T. McClure, J. McDonald

The U.S. Bureau of Mines has completed a laboratory evaluation of exhaust emissions from a diesel engine using an oxygenated diesel fuel. The fuels tested were soy methyl esters in a neat (100%) form and low sulfur, petroleum number 2 diesel fuel (D2). The engine tested was a Caterpillar 3304, indirect injection, naturally aspirated, 75 kW, diesel engine that is typical of engines used in underground mining applications. The objective was to determine the extent to which oxygenated fuels, such as methyl esters, reduce diesel particulate matter (DPM), and their influence on upon gaseous emissions such as total hydrocarbons, CO, NOx, NO2, formaldehyde, and other exhaust emissions. Heavy- and light-duty transient tests were used to simulate load cycles typical of mine applications. The soy methyl ester fuel produced greater amounts of volatile DPM (organic material) but much less nonvolatile DPM (carbon soot) for overall DPM reductions. A diesel oxidation catalyst (DOC) typical of the type commonly used in metal and nonmetal mines was tested with both fuels. The DOC further reduced the volatile and total DPM when used with the soy methyl esters, but increased the total DPM for D2 due to sulfate formation. The soy methyl ester fuel reduced CO and hydrocarbon, and NOx emissions. The DOC further reduced CO and hydrocarbon emissions.

Jan 1, 1995

By F. W. Brackebusch

Paste backfill is a pumpable, flowable, non-Newtonian fluid consisting generally of mine tailings and cement. Paste is prepared from dilute slurries of tailings. This is done by dewatering the slurries with conventional thickening or filtering. Backfill with a paste consistency is prepared by mixing dewatered tailings with cement and water to obtain the desired consistency of medium slump concrete. The paste is pumped with concrete pumps over relatively long (1 km or 0.6 mile) horizontal distances. More commonly, though, it flows by gravity down a mine shaft and then horizontally to the void being filled. Alternatively, cement can be added near the end of the pipeline. A certain proportion of fine particles <20 µm (<625 mesh) must be present in pastes but particles of aggregate can be added without significantly affecting the flow characteristics. Detailed testwork is necessary to design a system to prepare and place paste backfill. Testwork must determine dewatering characteristics, strength of mixes and friction in pipelines. Plants must be well engineered and controlled with PLCs because high quality control is necessary to prevent plugged pipelines and excessive pressures. Relatively small amounts of cement (3% to 5%) produce stiff backfill material 1.5 to 3.5 MPa (217 to 507 psi). The advantages of paste backfill in a mining operation include reduced mine dewatering, labor and materials savings, reduced tailings impoundment requirements, good support properties and reduced spills underground. In certain cases where more than 30% of the weight of the ore is sold as a product, the entire tailings stream can be placed underground. Paste technology can he used for surface or underground placement of tailings.

Jan 1, 1995

By K. Biswas, S. S. Peng

The stability of pillars in old mined-out districts is greatly dependent on the weathering action caused by moisture penetration into the pillar structure. Field observations in old mining districts indicated that this weathering action becomes critical in terms of the stability of the pillar if the coal seam contains parting or binder (layers of claystone or mudstone). The weathering action caused by moisture penetration over a long period of time degrades both parting and coal. However, it has been observed that the structural deterioration is more severe in parting. Moisture-penetration rates in parting and coal are different. The extent of the weathered zone in various layers of the pillar is primarily time dependent. This paper investigates, both in the laboratory and in the field, the effects of weathering action on coal and parting. In the laboratory, slake durability indices and uniaxial compressive strength tests for dry and saturated specimens are compared for coal. In the field, the in situ strength profiles for coal and parting layers are obtained, and the effect of time (in terms of the pillar age) on the strength profiles is studied An attempt was also made to establish formulae for time-dependent strengths of coal and parting.

Jan 1, 2000

By Robert J. Timko, Edward D. Thimons, Robert L. Derick

In early June, 1986, a fire of unknown origin erupted in one of several main entries of a coal mine located in southwestern Colorado. The fire was aggressively fought with high- expansion foam. As a result of several strategic decisions, the fire appeared to be held in check. Unfortunately, sufficient quantities of foam were unavailable and as soon as the foam was depleted, control of the fire was lost. To prevent further damage and the possibility of an explosion, all entries to the mine were sealed. This paper recounts activities from the discovery of the fire to the initial reentry of the sealed mine including location of the fire, the decisions made to best combat it, and the steps taken to rapidly and securely seal the mine when this became necessary. The mine operator requested the Bureau&apos;s assistance in obtaining and analyzing mine fire gases taken from sampling ports placed through the mine seals. This report describes how samples were taken and what gases were analyzed. In addition, this work describes the initial exploration of the sealed mine by personnel using oxygen breathing apparatus.

Jan 1, 1987

By B. T. Stanley

The basic geological data, derived from boreholes, exploratory test pits, drivages, and mine development, include information on parameters such as ore thicknesses, grades, depths below surface, structural attitudes of beds, rock types, and lithology of beds overlying and underlying the deposit. These data are usually supplemented by analytical information obtained from more detailed chemical, physical, and structural investigations of the various horizons. Even then, the relatively small number of sample points in the ore body and the sparsity of the sample volume make it necessary that the available information be interpolated between sample points and extrapolated into areas beyond the limits of the sample points. Such interpolation and extrapolation are usually done by making suitable assumptions about the parameter&apos;s continuity in the ore body and by building a suitable mathematical model. The mathematical model provides the values for chosen parameters at the nodes of superimposed conceptual grids of any desired dimensions such as a grid cell equal to the size of a mining block or any other criterion. This network of values, for any parameter, can then be used for mine planning, designing, and controlling functions. Additionally, these data can also be used to calculate ore reserve and quality in total and/or for any required block. Figs. 1 and 2 broadly illustrate the scope of work that may be involved in a geological ore-body modeling study for a coal deposit. Figs. 3 through 6 describe the scope of a commercially avail- able computerized system (MEDSYSTEM of MINTEC, Inc.) for creating drill-hole data base, mineral inventories, and for planning coal and uranium projects. The application of MEDSYSTEM to calculate reserves and to long-range planning in steeply pitching coal deposits is described in subsection 3.4, Chapter 4.

Jan 1, 1979

By Eric Forssberg, Mats Hallin

INTRODUCTION Evaluation and optimization of mineral processes has been going on since the the first plant started hundreds of years ago. A huge mass of knowledge has been collected since then. The main problem with this type of empirical knowledge of complex processes is that it is very difficult to formulate and document. The methods used for collecting the knowledge is not consistent but-varies with "he person" that does it. In the late 60&apos;s and early 70&apos;s efforts were made to use computer based techniques to evaluate process performance and to formulate process models for mineral processes. Models were developed, such as the flotation model by R. P. King (1973) which is still used to simulate flotation circuit behaviour. During the 70&apos;s. a number of mass balancing packages were developed together with process simulation packages. The industrial sector also made great efforts to develop and utilize computer based systems for process control and evaluation. The expert system that BOLIDEN created in 1974 at the Kristineberg plant was a remarkable achievement considering the hardware (CDC 3600) and the software tools (FORTRAN) available at that time. The main obstacle to successfully implement optimizing computer control of mineral processes was and still is the limited knowledge about the dynamics of complex processes. There are, however. many activities going on in this area today and it seems that the technology is very near a break through. Process evaluation is the most important tool to improve and maintain the optimal performance of a process. Today dedicated computer based techniques are used for fast and reliable screening of the processes. The stages in process evaluation consist of three basic steps: - Data acquisition, manually or by data logging. - Data refining, mass balancing and parameter calculation. - Data evaluation. The refined data can then be used for model construction/calibration and subsequently for process simulation. This paper describes two studies where the techniques mentioned above are used to evaluate and simulate

Jan 1, 1991

By Euler De Souza, Jason Chew, Aldrich Philip Dirige

Sillmats are structural elements upon which the safety and economics of underfill mining or sill pillar recovery in stopes of moderate width with steeply dipping ore zones, depend. The traditional stability design of cemented sillmats appears to have developed from experience and from standard static physical model tests such as uniaxial and triaxial compression. Such standard static physical model testing approach arrives at some approximate parameters, normally used to describe or predict the behaviour of sillmats in analytical or numerical models. This approach offers inherent limitations and generally results in conservative designs. Centrifuge modeling studies are combined with numerical modeling in this paper to provide insights into sillmat strength behaviour. The results of both modeling techniques suggest that, in stopes with smooth rock wall conditions, sillmat failure is driven by the fill self-weight and has minimum dependency on the fill binder content. In stopes with rough rock wall conditions, however, the wall roughness contributes significantly to the stability of the sillmat during underfill mining. This study indicates that the stability of paste fill sillmats can be designed with confidence using centrifuge physical modeling in combination with numerical modeling.

Jan 1, 2001

By Robert H. Marshall

The application of simulation to production planning at a large, complex open-pit mining operation proved to be challenging and enlightening. The mine is divided into two separate pits and several dump areas which are served by the same truck fleet. The operating system consisted of shovels of two different sizes, wheel loaders, and a fleet of three different truck types moving material from seven source locations to ten dumping sites. The interconnecting haulroad network included many common segments. There were operating constraints unique to the system, such as: traffic rules; manpower limitations; shovel, material-type, and destination priorities and production limitations; and a unique, non-centralized dispatching method for truck distribution. The truck distribution was further constrained by the matching of trucks to shovels, loaders, and destinations by truck type. The gathering and transformation of input data as well as the evaluation of results and validation of the model were also challenging. Despite a high level of sophistication in production reporting, some input data were neither readily available nor backed by field observation. As a result, many innovative techniques had to be used to develop realistic input data and to validate the simulation results. Nevertheless, this case study definitely proved the feasibility of applying computer simulation techniques to short and long range mine planning and budgeting at a large, complex mining operation.

Jan 1, 1982

By Joel Nonnweiler, Galen Samuelson Nagle

The Sacramento Regional County Sanitation District (SRCSD) has undertaken an interceptor expansion program to meet future wastewater needs associated with projected growth over the next 20 years. The Lower Northwest Interceptor (LNWI) will include over 17 miles (27 kilometers) of pipeline including 14 miles (23 kilometers) of dual force main ranging in size from 54- to 60-inch (137- to 152-centimeter) diameter and 3 miles (5 kilometers) of 120-inch (305-centimeter) diameter gravity pipeline. The estimated capital cost for the program is $331 million, with approximately $236 million in construction cost (as of November 2002). The project includes 4,700 feet (1,433meters) of tunnel including 2 crossings of the Sacramento River and one crossing of the Barge Canal, and 11 other smaller tunnel crossings beneath various creeks, sloughs, highways, and railroads. Preliminary design of the tunnels for the LNWI are discussed in this paper. The overall purpose of the preliminary design was to sufficiently define the project to allow planning level cost and schedule estimates to be performed. There have been changes to the project during final design including pipe sizes and configurations, tunnel and pipeline lengths and anticipated flows. This paper addresses only the preliminary design of the LNWI tunnels. Final design issues and changes made since completion of preliminary design are not addressed in this paper.

Jan 1, 2003

By A. F. McKown, P. E. Sperry, W. L. Fourney, D. E. Thompson

INTRODUCTION Underground drill and blast excavation is usually accomplished with small diameter holes loaded with high energy explosives. The detonation pressures are extremely high and an extensive amount of energy is dissipated in the process; however, very little of this energy is used to create the specified fracture planes required for excavation. The available energy is expended in producing radially outgoing stress waves, in crushing the adjacent rock, and in producing a dense, randomly oriented radial crack pattern about the holes. This causes several undesirable effects: 1. Overbreak at the perimeter, which results in more muck to remove and extra concrete or shotcrete to fill the voids. 2. Damage to or loosening of the remaining rock at the perimeter which may result in the need for additional support measures. 3. Ground vibrations and/or airblast, which could result in damage to nearby structures and complaints by people living or working in the area. Several steps may be taken to minimize these effects. Where control of the perimeter is desired, smooth blasting techniques are generally employed in which the spacing and burden of perimeter holes are reduced and lighter, decoupled charges are used. Where vibration damage to structures is feared, control is generally exercised by limiting the charge weight per delay period so that the ground vibrations at the nearest structure do not exceed a peak particle velocity of two inches per second. Where blasting complaints may be a problem, con-

Jan 1, 1979

By J. F. T. Agapito, C. E. Brechtel, C. J. Gilbert, T. R. Kelly, R. C. Karlson

A multi-lift benching cut-and-fill mining method was adopted at Asamera Minerals (U. S.), Inc.&apos;s Cannon Mine to balance the goals of high productivity and near 100 percent recovery with the need to minimize subsidence. High strength backfill was required to provide effective long-term overburden support and safe working conditions during the pillar recovery operations. Operational designs were evaluated using numerical modeling to predict global mine stability and backfill strength requirements. These models incorporated sequential mining of primary stopes, backfilling of primary stopes and recovery of pillars, and have been transferred to the mine operations group for use in evaluating different production sequences. The modeling has provided a better understanding of the structural response of the mine to excavation of the primary stopes and removal of the pillars. Predictions about the transfer of overburden weight to the abutments, pillars and cemented fill pillars have provided a criterion to evaluate mining plans and production sequence. Comparison of these predictions with actual mine structural performance has developed confidence in the design of the mining method and in the geomechanical design methods being employed. Primary mining of the B-North zone is nearly complete, and the stopes have been generally stable, as projected in the original design. Some exceptions have occurred where locally stope pillars have failed due to the presence of adversely oriented sheared beds. Recovery of the pillars between the

Jan 1, 1987

By J. W. Mahar, E. J. Cording

INTRODUCTION In exploration for rock tunnels, the geology should not only be described, but its effect on excavation and support assessed. It is not an easy task to correlate exploration results with support and excavation requirements, even when the exploration program is detailed and geologic conditions are relatively well known. Many of the significant geologic features are subtle and their effect is difficult to interpret from exploration results. However, in similar geologic settings, there are specific geologic features which will cause recurring support problems. Such features should be actively sought out when exploring in a given geologic setting. In blocky and seamy rock, the primary features controlling performance are the joints, shears, and shear zones. This paper describes the effect of such features on the formation and movement of rock wedges in tunnels driven in foliated metamorphic rocks in Washington, D. C. and New York City. In both areas the foliation commonly forms a N-S striking plane of weakness along which major shear zones, shears, and joints have formed. In addition, the structural history of the two areas has been similar, so that there are similarities in the orientation and character of the other major joint sets and shear zones in the rock mass. The observations were made in tunnels ranging from 10 to 70 ft in width and excavated at depths ranging from 80 to 800 ft. Most of the tunnels described were deep enough to be located in unweathered rock, or in rock only slightly weathered along joints and shears. Variations in the planarity, filling, spacing, and attitude of joints, shears, and shear zones accounted for significant differences in the

Jan 1, 1974

By L. Alan Weakly

The purpose of this paper is to present a viable method of reinforcing rock pillars by utilizing fully grouted reinforcing steel and a cement - fly ash mortar. Although the fully bonded bolt concept is not new, as exemplified by the present widespread use of resin bolts within United States mines and by the use of cement grouted reinforcing used as back pins in the Kiruna Iron Ore Mine in northern Sweden, (1) (2) the method of stabilizing mine pillars with fully bonded reinforcing is new. This method, called the "grout-rebar system", was first incorporated at St. Joe Minerals Corporation’s Fletcher Mine in December of 1972. The system was used on an emergency basis before extensive research on the mechanics of the system could be completed. Since December of 1972, however, approximately 206 pillars have been reinforced at Fletcher and the system is currently being used on a regular basis at two other St. Joe mines and at two competitor mines in the area. Basically, this paper is a case study of the efforts, research and results of utilizing the grout-rebar system, on a selective basis, at the Fletcher Mine. In addition to information about the system, this paper will explain in detail the three rock mechanics instruments developed by St. Joe and used to measure and monitor rock movement to validate the grout- rebar system.

Jan 1, 1977

By A. Venkatachalam

Spinel ferrites, like NiFe2-2x Znx Ti4 O4 Fe CO1.5 Ge0.5 Tix O4, Ga1-x Fex Ni CO O4, Nil-x Fex Mn2 O4 have been prepared using the respective metal oxides in Stoichiometric quantities, by the ceramic method. The oxides were homogenized in acetone medium, pelletifed by using poly vinyl acetate as the binder. They were fired at 1000°C for 100 hours for compound formation. Chalcogenide spinels such as Zn1-x Cux Cr2 Se4 where 0=x=l and Cu1-x Fex Cr2 Se4 where 0=x=0.3 have been prepared by using 99.99% pure elements and then fired at 1000°C in quartz ampoules under vacuum conditions. X-ray diffraction studies of these compounds indicated a single cubic spinel phase. DC resistivity studies of the compounds were taken between 300-700K using LCR bridge by two probe technique. Thermo-electric power measurements were taken between 300-500K for all the compounds. Initial susceptibility studies have been carried out using a low field (0.506) and from which the nature of magnetic dimains and Curie temperatures were determined. Magnetic hysteresis measurements were carried out at 300K and at 80K, using alternating current hysteresis loop tracer, at 2K02 field. Mossbauer spectral measurements were carried out using Co57 source embedded in a copper matrix and an absorber containing 0.3 mg/cm2 of the sample. The spectra has been fitted by Mossfit Program. The catalytic effect of the spinel ferrites NiFe2-2x Znx Tix O4 where 0=x=1 has been studied by using the model reaction of decomposition of H2O2 at temperatures from 40°C to 70°C. It was found that the spinel oxides were found to possess poor catalytic activity.

Jan 1, 1990

By R. V. Ramani, J. Qin

During the mining process, the in-situ material is broken into different size ranges, from very large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable dust is associated with health and safety of the miners. The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined. The amount of respirable dust airborne is on the average only 0.016% of the respirable dust generated. On the average, 61% of the total airborne dust measured is in the respirable size range. The amount of respirable airborne is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (=0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of the airborne propensity of respirable dusts in mine atmospheres.

Jan 1, 1989

By Garland R. Dever

Extensive deposits of high-calcium limestone occur in the Upper Mississippian Warsaw and Ste. Genevieve Limestones in the region of the lower Cumberland, Tennessee, and Ohio Rivers in western Kentucky. Analyses of foot-by-foot samples from 20 quarries and cores in 8 counties show variations between the chemical composition of high-calcium deposits in the 2 formations. Knowledge of probable variations in composition should aid in prospecting for high-calcium stone for a specific use and in evaluating potential deposits. High-calcium strata in the Warsaw consist of bryozoan- and crinoid-rich bioclastic limestones, and in the Ste. Genevieve, predominantly oolitic limestones. Values used for comparison were obtained by averaging the foot-by-foot analyses of each high-calcium deposit, 10 in the Warsaw and 15 in the Ste. Genevieve. Average MgCO3 and Fe2O3 contents are generally lower in the Warsaw than in the Ste. Genevieve. Average SO2, S, and P contents are- generally higher in the Warsaw. No characteristic differences are apparent between the average CaCO3 and A1203 contents of the two formations. The higher S and P contents of the Warsaw are believed attributable to the predominance of biogenic material in these limestones. Within the Warsaw Limestone, higher average S and A1203 contents and lower average Fe2O3 contents were found in deposits in the northern half of the region. In the Ste. Genevieve, vertical variations in composition occur within individual high-calcium deposits containing oolitic and nonoolitic limestones. Lower average CaCO3 contents and higher average contents for the other constituents were found in the nonoolitic intervals.

Jan 1, 1972

By G. Triantafillou

The aim of this paper is to present the progress of the plan of the Greek Public Power Corporation S.A. (PPC S.A.) at the Lignite Centre of Megalopolis in Peloponnesus (southern Greece) to manage impacts on local communities in areas affected by its activities during the lignite mining operation and post-closure. The reclamation works in the waste dump areas of the mines that constitute the Megalopolis Lignite Centre, concerning the utilization of waste dumps for infrastructure community projects constructions are discussed. Moreover, selected environmental indicators concerning land use and closure and rehabilitation are presented.

Jan 1, 2008

By S. K. Das

A detailed strata-mechanics investigation and examination was carried out in the E2 Panel (ML-II/7) of the XVI Bottom coal seam, which is located in the Moonidih Colliery of B.C.C.L., Jharia coalfield, India. Above this panel, the XVI Top coal seam was previously worked out by a longwall panel. Based on intensive field study and on experiments in a number of longwall panels located within various Indian coal mines, the actual behavior of the coal roof strata was evaluated and new strata-mechanics concepts around the longwall panels were developed. These concepts resulted in new methodologies concerning the behavior of roof rocks, caving characteristics, etc. within longwall panels and in the area of strata mechanics. Based on these new strata-mechanics concepts, a very simple, but realistic, model was developed to determine the optimum capacity of the powered supports. This model considered the combined loads resulting from the detachment of strata and composite layer blocks from the face and, also, loads due to the deflection of strata and composite layers situated above the detached roof rockmass. This formula, along with the other related formulas by the author, prompted the determination of the optimum capacity requirement for the powered supports to be used in the XVI Bottom coal seam, located under the worked out area. This new concept in strata mechanics and capacity requirements of the powered supports in a longwall face may be an aid to Mining Engineers.

Jan 1, 1997

By Bruce Kennedy, Dan Nilsson

Mining means drilling and blasting in order to break down the rock, loading and transport, and often also crushing the ore down to a suitable size. These operations can be done in open pits or in underground mines, and also, to a lesser extent, in marine mining. The same operations are also used in various types of construction, i.e., for roads, water power stations, etc. Before beginning a detailed economic analysis of the factors which enter into deciding whether to mine by open-pit or underground mining, and at what point a change should be made from open-pit to underground mining, or vice versa, it is of interest to consider some general factors.

Jan 1, 1982