Search Documents

By E. Karampinos, P. Morissette

"INTRODUCTION Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting both appropriate systems and the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation. Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights on the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement over the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is not often available at mine sites. Even when the expertise is available it requires a major time and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support. Rock reinforcement is an integral part of all ground support systems used in underground mines. Long flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This paper focuses on the optimization of the cable bolting strategy in squeezing conditions at the LaRonde Mine by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 1, 2018

By Sandeep Upadhya, Marc Morgan, Baljinder Bassi, James Fletcher, Mike Deevy, Nishant Nayan

"In order to protect public safety in the event of a deliberate fire attack, underground rail authorities are increasingly considering the need to design for arson-initiated fire scenarios. Where typical design fires for modern rolling stock mean a peak fire size is reached after 12 minutes, an arson-initiated fire reaches its peak within 2-3 minutes. We present the innovations required to successfully incorporate this requirement on a recent design-build project. In stations 3D modelling is used to optimise smoke reservoir designs, smoke chimneys, station boxes and tunnel geometry to allow coordination with structural requirements. In tunnels, novel coupling of one dimensional network modelling and 3D Computational Fluid Dynamics (CFD) is used to improve assessment of complex fire scenarios. Finally, the impact on tunnel structures is assessed through comparison with standard time-temperature curves and risk of explosive spalling. INTRODUCTION An increasing regulatory environment and the appreciable influence that terrorist incidents have had on public safety policy have motivated the need to protect against large arson fires, especially in civil structures and public transport systems. With a greater reliance of a growing urban population on underground subway systems, design of such infrastructure is continually being reassessed and developed worldwide. Underground rail authorities are paying increased consideration to the design of fires - with properties beyond the upper regions of growth and intensity - amongst arson fire studies. Use of fire hardened materials on modern rolling stock means fires caused accidentally can be expected to develop relative slowly. However, recent experiments involving large initiating fires (as would result from an arson attack) have shown rapid fire growth rates and flashover leading to greater maximum heat release rates, Hadjisophocleous (2012), White (2010), and Lönnermark, et al. (2015). This paper describes the challenges and innovations required to complete a detailed design to control smoke from such aggressive super-fast growing fires. Computational modelling is used to demonstrate the required smoke control design by configuring the mechanical exhaust system combined with careful coordination with the architectural and structural design. The design objectives are to provide tenable egress paths in accordance with NFPA 130 (2014) and fire-fighting access. Finally, analysis of the design fire is used to inform the tunnel lining design, reducing the risk of explosive spalling, protecting the asset in the event of a severe fire."

Jan 1, 2016

By Sukumar Bandopadhyay

In recent years, research in the field of artificial intelligence (AI) has had many important successes. Among the most significant of these has been the development of powerful new computer software known as the "expert systems". Expert system programs designed to provide expert-level consultative advice in mineral exploration (Duda et al, 1981), scientific (Feigenbaum, Buchanan and Lederburg, 1971) and medical (Shortliffe, 1976) problem solving are generally acknowledged to be among the forerunners of this research. As the decision makers virtually in all fields face a more complex and involved world within which to operate, the need for some decision support is also becoming urgent. Thus applications of expert systems continue to spread out reaching problems that, because of their dimensions or particular aspects, set more demand on the decision methodologies. To meet these new requirements, many activities which were performed in the past by the domain expert or engineer must become automated. Furthermore, previous research (Dawes and Corrigan, 1974; Dawes, 1979) has shown that automating an expert's decision rules often provide better decision than the expert does. For large systems it would be very useful (or even necessary) to have formal tools, allowing one for example, to automatically discover inconsistencies, contradictions or redundancies, or to identify the possibilities of wrong lines of reasoning in the decision process.

Jan 1, 1990

By R. J. Piniazkiewicz

Talc orebodies are mined in Asia, Australia, Europe, North America, and South America. Operators in North America must be efficient quality suppliers to thrive in a talc market in which many overseas suppliers have advantages such as lower hourly wages, shorter distances to ports, and less government regulation and intervention. Continuous improvement through teamwork and innovation is needed in the following areas to thrive amidst worldwide competition: 1) Maximization of the in-place value of ore. 2) Research and development to yield new processes and products. 3) Safe productivity. 4) Involvement in legislative processes. 5) Wellness programs to lower health care costs.

Jan 1, 1993

By C. F. Kaiser

The Broken Hill proprietary company Limited grate kiln pellet plant (1) located at Whyalla in South Australia commenced production on May 13, 1968. During commissioning, about 25,000 long tons of fluxed pellets were produced. Plant performance was satisfactory and acceptable under the plant guarantee. For production reasons, it was necessary to curtail the fluxed pellet run and revert to the production of acid pellets. In 1970, some 250,000 long tons of fluxed pellets were produced under varying operating conditions to determine the requirements for optimum quality pellets at acceptable production rates. In excess of 180,000 long tons of these fluxed pellets were exported to Japan. Problems experienced in production of the fluxed pellets are detailed, and the quality of the fluxed pellets compared to that of normal acid pellets produced at Whyalla. Brief Plant Details Run of mine ore treated was predominantly soft and friable and contained an average of 66 per cent Fe, 1.7 per cent Si02 and 1.8 per cent Al203. The main iron mineral in the ore was hematite with some martite also present. Plant feed was ground dry in ball mills 11 ft in diameter by 29 ft long to a Blaine surface area of 1600 sq.cm/g and the ground ore was wetted in a pug mill. Balling was carried out in balling drums 10 ft in diameter by 32 ft long. Induration equipment included an eighteen windbox grate 12 ft 2 in. wide by 164 ft 1 in. long, a rotary kiln 18 ft 6 in. diameter by 118 ft 8 in. long and an annular cooler 50 ft mean diameter by 7 it wide.

Jan 1, 1972

By E Marambio, R Brändle, G Fischer, G von Rickenbach, L Burgos, R Luis Fonseca

Ground support systems must provide safe and effective designs for underground excavations under high stress conditions. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the arrangement, measurement, results, and the preliminary analysis of a single impact dynamic test performed during 2021 of a ground support system with a high-tensile steel wire mesh MINAX 80-4.6 is presented.

Apr 26, 2022

By Thomas Schwind, Elmar Feigl, Gerald Skalla, Angelos Gakis

Cedarvale station was constructed as part of the Eglinton Crosstown Light Rail Line, under the operational Yonge-University Line Subway box of Toronto Transit Commission (TTC). The station was constructed as an open-cut, which necessitated the underpinning of the existing TTC box to minimize the impact on the Subway and allow its unhindered operation. Six mined galleries, 4 m wide by 2.75 m high, were excavated sequentially (SEM) immediately under the existing box, to provide the required space for the installation of the main underpinning beams. This novel solution was executed successfully providing quick access for the main excavation works to commence.

Dec 1, 2022

By M. Shahsavar, J. Sattarvand, J. Gomez

Mining can be categorized as a hazardous activity, considering some factors such as environmental conditions with a considerable presence of humidity, suspended particles, or falling rocks have affected the severity and number of accidents compared with other economic sectors. The industry analyzes incident reports to narrow the rate of severe injuries and fatalities, conducting root cause analysis and identifying leading indicators. As the International Council on Mining and Metals noted, the vast trove of incident data is not analyzed as much as possible due to a lack of analytics expertise at mine sites. However, machine learning could solve the problem of analyzing all the incident data in a no-timeconsuming way, considering the abundant data, and without using expert personnel in data science. Thus, a Convolutional Neural Network and a Naïve Bayes model were introduced to perform classification in the MSHA database. The database from 2020 consists of 60 fields to describe safety incidents; these fields include mine I.D., accident date, subunit (mill, surface), material extracted, and other metadata.

Jun 25, 2023

By Y. T. M. Ocsa, V. O. Tenorio

This research is the result of a geotechnical study carried out in a natural slope in an Open Pit mine in Southern Peru, highlighting earthquakes as an important cause of instability within the case study presented. This leads to analyze the stability of a slope, according to the safety factor and thus consider a future construction in its environment according to the identified requirements. There are known disasters at national and international level that involve human lives because of the lack of analysis of slope stability conditions, which based on the results will allow to control and to take adequate corrective measures. These mass movements are classified whether they are soils or rocks, considering the mechanism and type of rupture, as well as the presence of water, the speed and magnitude of the movement. The movement problems are due to factors of inherent nature and constitute a reason to perform a calculation study to analyze and estimate the safety factor of each of the evaluated cases

Mar 2, 2022

By Thomas Fiest, Helmut Wannenmacher, Wulf Schubert, Manuel Entfellner

Mining and tunneling in so-called “squeezing ground conditions” at high in-situ stress can result in substantial and enduring ground deformations. The magnitude of deformations is closely tied to the applied excavation- and support concept, though typically, they can reach tens of centimeters. The yielding principle is based on the idea, that the need for support capacity decreases as deformation increases. To enable controlled ground deformation and safe working conditions, yielding elements as a part of the shotcrete lining are implemented. These types of elements avoid an overstressing of the shotcrete lining. During the deformation process, the support pressure of the yielding elements and lining increases, thus stabilizing the ground. Furthermore, long-term creep deformations of the rock mass can be absorbed with such a system. This economic support technique represents the state-of-the-art infrastructure tunneling practice in squeezing ground condition. A novel yielding element of High-Strength Expanded Polystyrene (HS-EPS) was invented, which overcomes existing systems’ drawbacks. This innovative system is lightweight and allows for safe and rapid installation. Furthermore, the modular setup of the element enables an easy on-site adaption to react to in-situ deformation patterns and changing ground conditions. Recent experiences from applications in Alpine base tunnels in squeezing ground are presented.

Jun 25, 2024

By Jackson G. Jenkins

Magma Copper Company's San Manuel SX-EW facility has operated since May, 1986. The original facility had a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solution from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing in-situ leach solutions. This paper focuses primarily on the heap leaching area with regard to exploration, testing, feasibility, permitting, design and construction, and operating practices. Research utilizing surfactant leaching aids to enhance copper recovery is also discussed.

Jan 1, 1993

By Kal V. S. Sastry

Mathematical and expert system models are being used extensively for mineral process engineering. There exist no standardized methodologies for their computer implementation. In meeting this need, this paper introduces the concept of a process software model, or simply a software model and presents a two-step methodology for its development involving software model specification and development. The software model specification is to be performed after extensive discussions with the ultimate users of process software based on which the software model is developed. These software models provide a formal basis for the design and construction of software objects corresponding to the real world process objects.

Jan 1, 1994

By Britta Schoesser, Zdenek Zizka, Markus Thewes

"The support pressure of a slurry shield corresponds to the in situ earth and groundwater pressure to ensure the stability of the tunnel face. The support fluid (bentonite suspension) penetrates from the excavation chamber into the pore space and transfers the support pressure to the granular structure of the soil within this zone. At the same time, the cutting tools rotate periodically with the cutting wheel and remove the penetrated soil up to a certain cutting depth at the face. Shortly after the tool passing, the penetration process starts again. Both, the support pressure and the soil excavation, act in the same direction at the tunnel face, but they are subject to different cyclic intervals. This relationship between the time needed for the transient penetration process and the interval of the cyclic passage of the cutting tools at a local point at the face is examined and the impact onto the global face stability is discussed. INTRODUCTION Slurry shields are usually deployed for excavations in soft ground. The main application range is in non-cohesive soils (DAUB Recommendations 2010). In non-cohesive granular soils, the tunnel face stability is one of the key design issues. The slurry shields make use of pressurized bentonite suspension (slurry) to support the unstable tunnel face. To support the tunnel face effectively, the slurry pressure has not only to counter the groundwater pressure, but also has to be transferred into an effective stress to support the soil grains. In general, the pressure transfer can be achieved in two ways: (1) with a thin flexible membrane or (2) a penetration zone. The membrane (1), called filter cake, creates a thin impermeable layer from bentonite particles directly on the tunnel face, and enables a transformation of excess slurry pressure into effective stress. In case of penetration zone formation (2), the excess slurry pressure is transferred onto the soil skeleton along the entire penetration depth by shear stresses between slurry and soil grains. These theories, presently applied to assess the pressure transfer on the grains within slurry shield tunnelling, are originating from diaphragm wall technology, e.g. Müller-Kirchenbauer (1977), Kilchert and Karstedt (1984). They assume that the support pressure transfer mechanism is built-up instantaneously on the whole tunnel face and is not damaged or influenced by the interaction with excavation tools. These assumptions are valid for conditions during the excavation of diaphragm wall trenches whose bottom is excavated and the walls of the trench are supported. At the tunnel face of a slurry shield, the support suspension acts on the same area as the soil excavation. Hence, the conditions on the tunnel face are transient (time dependent) due to the time period needed for the penetration process of the slurry and the periodical damage of the pressure transfer mechanism by excavation tools (Fig. 1a)."

Jan 1, 2016

By D. M. Fritz

Environmental experts face large and rapidly-increasing volumes of raw data obtained from environmental monitoring stations. These professionals must compile and analyze the data in a systematic manner to cost-effectively understand and minimize the impacts of mining. The shift toward desktop computing, combined with the downsizing of company staffs, has now more than ever created a demand for a modern, PC-based application for the storage, retrieval, analysis and presentation of environmental data. This paper discusses the general requirements of such a system, and points out specific ways in which such industry-specific software can provide convenient and useful access to the data. The software used to illustrate these features is the HydroDat program, developed by Western Water Consultants, Inc.

Jan 1, 1996

By J. Bacho

The modern drilling fluids industry is a dynamic, evolutionary environment. It is continuously striving to satisfy and anticipate the ever-changing needs of the oil and gas industry. The predominant driving forces in the industry over the past decade have changed dramatically. Health and environmental issues, coupled with economic and performance requirements, demand innovation and change from the drilling fluids industry. Emerging drilling fluid technologies will demand environmental considerations from mined components with additional emphasis on cost and performance criteria. Drilling fluids providers continue to search for and identify environmentally sensitive components which meet or exceed the performance of their more toxic predecessors. These changes have and will impact the components of drilling fluids that are mined.

Jan 1, 1994

By G. T. Homce

Most electric motor predictive maintenance methods have drawbacks that limit their effectiveness in the mining environment. The U.S. Bureau of Mines is developing an alternative approach to detect winding insulation breakdown in advance of complete motor failure. In order to evaluate the analysis algorithms necessary for this approach, the USBM has designed and installed a system to monitor 120 electric motors in a coal preparation plant. The computer-based experimental system continuously gathers, stores, and analyzes electrical parameters for each motor. The results are then correlated to data from conventional motor-maintenance methods and in-service failures to determine if the analysis algorithms can detect signs of insulation deterioration and impending failure. This paper describes system design and implementation. At this writing, however, installation is still underway, and field data analysis results are not yet available.

Jan 1, 1994

This United States Bureau of Mines study is based on a review of U.S. mine fire accidents that occurred from 1970 through 1989. Information on these accidents was obtained through investigative reports written by Mine Safety and Health Administration personnel. For this study, 260 mine fire accident reports were examined. A previous Bureau research effort established that fires causing fatalities were more likely to occur in haulage entries than at any other underground location. This study has found that the most prolific source of haulage entry fires was the inadvertent grounding of trolley wires. The largest segment (15 out of 40 trolley wire fires) resulted from not maintaining adequate clearance between the trolley wire and the vehicle. Several novel fire prevention and control ideas have evolved in response to frequently occurring fire-related problems. These included; discriminating power isolation devices, wire cutting devices, more accessible fire extinguishers, vehicle overcurrent protection, and vehicle fire suppression.

Jan 1, 1994

By S. B. Hildebrand

One of the highest costs associated with insitu leaching of copper is electric power. The ReGeneration Project addressed this cost issue with a research and development project for BHP Copper. The project involved the installation of a reverse pump/turbine for the removal of excessive fluid pressure and the production of useful electric power. The motivation for the project was that a reverse pump/turbine unit could not only remove the excess hydraulic pressure, but when connected to an induction .generator, would produce electric power, which could be easily connected to the local power gird, thus reducing operating costs. The project was successful in removing excess fluid pressure and producing electricity. The unit is operating today, producing useful 2,300 volt power at a rate of approximately 128 kilowatts.

Jan 1, 1998

The past decade has seen remarkable progress by the railroads both in equipment and concepts in the handling of dry bulk. materials. While such shipments have always been an important part of the traffic handled by the railroads I little was done to improve the efficiency of handling or toward attempted optimization of equipment design before 1960. Several developments at about that time turned attention to this important segment of railroad traffic. One was the construction of a successful coal slurry pipe-line. Another was the promise of substantial economy in electric power transmission by ultrahigh voltage systems and finally, came the growing technological and economic feasibility of nuclear fuel electric generating plants. Each of these developments was a threat to the coal traffic of the railroads --the most important single commodity they handled in terms of revenue and tonnage. By the mid-1950's I Southern Railway management had become most concerned with its growing investment in freight car equipment and the declining revenue productivity of the capital employed. Additionally I there was substantial concern with the loss of business and potential losses in the area of the railroad's greatest economic advantage --bulk commodity movements. In 1958 a small team was established to study this problem. They arrived at two conclusions. The first conclusion was that within limits of maximum gross allowable weight on rail the lowest unit net capacity cost of investment came at maximum allowable gross weight per car unit. The second conclusion was that with a high degree of utilization costs per weight unit transported could be reduced to the pOint where

Jan 1, 1971

By G. Buchan

This paper discusses the design of long panels for longwall mining at Twentymile Coal Company (TCC) from conception to implementation. The case study of the long panels at Twentymile includes extensive mine plan reengineering in the early 1990's to world record production months in 1996 and 1997. The obstacles of subsidence engineering, environmental regulations, conveyance, ventilation, equipment design, and continuous miner (CM) development timing had to be overcome to successfully begin longwall production within a 4 year time frame. The background and some detail for each of these areas listed will be discussed to show how the coordination of many facets must be pulled together to implement a successful long panel mine plan.

Jan 1, 1998