Search Documents

By Y. M. Jiang, D. W. Park

Longwall faces can move at high advancing rates, but many geological variations can cause unexpected instabilities and production losses. The rapid movement makes it necessary to evaluate different geologic conditions in the rock mass as fast as possible to assess their effects on the longwall face and shields. It is believed that prompt awareness of geologic conditions is the key to preventing instability at a longwall face. This paper introduces the application of fuzzy set theory for characterizing and evaluating roof conditions. Real-time monitored data coupled with fuzzy set analysis provides valuable information, such as shield leg pressure, developing load on shields, intervals of periodic weighting and the ratio of developing loads during periodic to normal times.

Jan 1, 1998

By Robert J. Timko, Lincoln Derick

This work is a follow-up to previous research that attempted to predict the location of spontaneous heating episodes in underground coal mine pillars. The objective of the original work was to see if the data obtained by commonly used detection methods could accurately predict spontaneous combustion episodes in coal pillars. Data accumulation during the study was enhanced when a spontaneously generated fire occurred within one of the pillars being examined. The fire provided researchers with realistic data that could be used to determine if fire prediction was possible. Results from the initial study found that the atmospheric status equations that were used provided little advance notice that combustion would occur where it did. This study reevaluated the accumulated data by applying it to recently developed equations and compared these results with previously obtained information to determine if a combination of these techniques could more effectively predict impending combustion.

Jan 1, 1995

By Eleanora I. Robbins, Motoaki Sato

Many problems associated with acid mine drainage (AMD) are caused by the complex way molecular oxygen (O2) oxidizes reduced matter at surface temperatures. In aqueous solution, O2 kinetically "prefers" to go through the formation of hydrogen peroxide (H2O2) as an intermediate. Being innately unstable, H2O2 is quickly decomposed back to water and oxygen in the presence of dissolved Fe and Mn, both catalysts for the decomposition. Direct addition of H2O2 to AMD produced similar results. Ozone (O3) is a much faster and stronger oxidizer than either O2 or H2O2. In the laboratory, O3 rapidly precipitated Mn, Fe, Ni, Co, Pb, and Ag even in acidic solutions. The experiments indicate that AMD can probably be processed with ozone and metal oxides/hydroxide recovered in flow systems using only septic-tank-size reactors and small sedimentation ponds.

Jan 1, 2000

By M. Jaramillo

The expanded west pit of the 15 Mta (13.6 stpy) El Cerrejon mine will eventually reach a maximum depth of 270 m (890 ft). Slope-stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization calls for anchoring the footwall by the installation of 9- to 33-m- (30- to 108 ft-) long multistrand steel cable bolts. For each of the 15-m- (50-ft-) high mining benches, a row of bolts is installed with variable horizontal spacing, depending on the dip magnitude. Cable bolting is now standard operating practice, and an estimated 11,800 bolts will be installed during the life of the mine. Results to date have been satisfactory in terms of the stability condition of the bolted slopes.

Jan 1, 1997

By Edward F. Fries

Computerized, real -time monitoring had its beginning in the U.S. coal industry in the early 1970's. Over the last 10 years, developments in technology have made systems available that are capable of monitoring and controlling many mine parameters that can increase safety and production. However, situations currently exist where computerized monitoring systems are not being utilized to their fullest capability. They produce reams of printed output that are not sorted in a useful format, and human operators are not able to react fast enough in emergency situations tn tile large amount of information that the systems generate. A solution is the application of an expert system as the interface with real-time monitoring. An expert system would use an extensive knowledge base and human-type reasoning ability to make decisions on optimum strategies. Expert systems have been applied successfully to problems in other industries, and could provide significant benefits to mine information management systems. The use of an expert system with real-time mine monitoring is discussed in this paper.

Jan 1, 1986

By Jiqing Zhang, Jon C. Yingling, Andrzej M. Wala, Richard Ray

The purpose of this paper is to present how Computational Fluid Dynamics (CFD) simulations can be used to study the flow across the main airways of a mine ventilation system. in particular, the flow through the transition zone between the upcast shaft and main fan ductwork was investigated. These studies consider potential design modifications of this transition zone to reduce the energy cost. Although CFD has many advantages, it does not completely eliminate the need for experiments, which are still needed to validate numerical solutions. For this reason, data collected during actual mine tests and CFD simulations are compared in this pa- per. This comparison allows a better understanding of the flow phenomena. Moreover, once the numerical solutions have been validated, CFD can be used with better confidence to predict the effect of changes in ductwork configurations on energy losses. CFD reduces the number and cost of tedious experiments, while enabling a broader scope of design comparisons.

Jan 1, 1997

By Raymond S. Shrode

Limestone and dolomite production is of significant importance to the Baltimore and Ohio Railroad. Except for coal, more tons of limestone and dolomite are moved by the Railroad than any other mineral raw material. In the territory served by the Railroad, these materials are produced from every geologic system from Cambrian through Pennsylvanian. Some of the operations produce premium stone acceptable for high-specification steel and chemical use; at others, the stone finds application as aggregate materials and for cement manufacture. The Railroad is interested in seeing continued production from the operations it now serves, and in serving operations in a way mutually beneficial to the Railroad and to the producer. In working with producers, the importance of geologic knowledge in prospecting and development of deposits has been clearly recognized. In turn, knowledge of the economic and technological facets of production and consumption is needed for the geologists to participate with maximum efficiency.

Jan 1, 1966

By Don Rose

I. INTRODUCTION The Atlanta Research Chamber is an UMTA-sponsored applied research facility studying tunnel design, excavation and support systems. It is located directly below Peachtree Street in downtown Atlanta, Georgia. It is included in the CN-120 contract to build the Peachtree Center subway station, a part of the Metropolitan Atlanta Rapid Transit Authority (MARTA) multi-billion dollar "Phase A" 53-mile transit project, which is 80 percent funded by UMTA with 20 percent provided by local authorities in Atlanta and Fulton and DeKalb counties (Figure 1). The Research Chamber is located immediately south of the main Peachtree Center Station cavern, and is in part an enlargement of the pre-existing Pilot Tunnel excavated to provide bidders on the CN-120 contract a view of the rock conditions (Figure 2). The Research Chamber lies some 3 meters above, and is approximately parallel to, the twin Running Tunnels. The Research Chamber is 18 meters long and has the same 5.5 meter diameter horseshoe shape design dimensions as the twin Running Tunnels.

Jan 1, 1979

By H. Lyn Bourne

This is the 10th annual tabulation of US mineral royalties published in MINING ENGINEERING. The first year, 1982, the author solicited information about royalties and the cost of reserves. That column contained only a few royalties - not enough to tabulate. Since then, the response has been sporadic but the entries have grown to more than 300. Some have been deleted. Some of the older information has been deleted to make room for new entries. All indications suggest that the readers enjoy and use the information. But more information is needed. Russian practice In 1989, this column gave a brief history of mineral leasing and royalty payments as the concept applies to mining in the United States. This year's narrative deals with information about the mineral ownership in Russia. That country is in political and economic turmoil, including administrative systems and methods. And many laws are likely to change. What follows describes the Russian system of mineral ownership as of early 1992, according to Kirill Kavun. He begins "All the subsurface space of the Russian Federation with minerals contained belongs exclusively to the state. This forms the Common State Mineral Fund. Land parcels may be state, municipal, public or private property. They may be let to be owned and used by individuals, juridical persons, national/territorial or administrative/ territorial formations." This seems to apply to surface rights, as known in the US.

Jan 1, 1992

By David R. Baughman, John C. Gathje, K. C. Oberg, Gary L. Simmons

Santa Fe Pacific Gold Corp. conducted pressure-oxidation pilot plant studies on refractory carbonaceous gold ores from the Twin Creeks Mine in Nevada. The tests were conducted at Hazen Research Inc., Golden, CO, during 1993 and 1994. Laboratory investigations using CIL cyanidation after batch pressure oxidation demonstrated gold recoveries of 90% to 95%. However, pilot plant testing showed that several of the same ore types responded very poorly, with gold extractions of only 45% to 75%. Plant testing was suspended for approximately four months while extensive research was conducted to determine why these ores responded poorly and to identify potential solutions. This paper describes the batch and pilot plant test results, the extensive research activities that eventually identified the cause of the gold recovery problem and the final semicontinuous and continuous pilot plant operations that confirmed possible solutions. Final pilot plant results showed gold recoveries that were consistently greater than 90%.

Jan 1, 1999

By P. T. Brown

Denison Mines Limited, Canada's largest uranium producer located in Northern Ontario recently embarked upon an extensive development program that would allow them to substantially increase production and also meet the more stringent air quality standards established by the ministry of Natural Resources. To proceed with this program it was essential that the fresh air supply be greatly increased to the underground workings. A major portion of the mining area is located under Quirke Lake on the north limb of a syncline termed the Quirke Lake trough. The Denison engineers determined the most practical size and location for a proposed new fresh air shaft, eventually deciding to drive a 25 foot diameter shaft, 490 square feet in section for 1,800 feet long vertically. The shaft collar would be located on Roman Island, an island in Quirke Lake. A test hole was drilled from Roman Island to determine the ground through which the ventilation shaft would pass. This drill hole confirmed the location of the Quirke Lake over-thrust fault, a highly fractured water bearing zone 165 feet thick, approximately 800 feet below surface. Plans were made by Denison Mines Limited to seal and consolidate this ground when it was encountered by the shaft.

Jan 1, 1974

By I. E. Lewis, W. R. Hopkins

Flowsheet improvements, such as series/parallel SX plant configurations, discontinuation of plant sumps and improved filter pumping concepts, the use of in-settler baffle systems, and the Krebs and combined mixer-settler designs offer opportunities to reduce SX plant cost. Today's plants employ permanent cathodes and mechanical stripping, and the increased capital cost can be offset by labor savings and higher current densities. The wider use of HDPE and new cell construction materials also reduce capital cost. The "Portelex" type of relocatable design embodies such new, cost-saving measures in a simple basic plant. Organic inventory and losses are reduced by new, fast-settling, hybrid organic reagents with improved kinetics and selectivity.

Jan 1, 1991

On longwall coal faces in some Japanese coal mines more than half of the air coming from the intake gate road flows into the caved goaf and the air heated by the hot waste rocks in the goaf comes out through the latter half of the face. This still constitutes a major heat problem in spite of the introduction of gate and face air coolers. Therefore, in order to establish effective measures to improve the environ- mental conditions, it is essential to obtain information pertaining to the air flow pattern on the face as affected by the goaf conditions and the air flow regulating measures taken at the intake side of the face. Experiments for this purpose were carried out using a coal face model. The model was reduced to a scale of 1110th of the real face measuring 100 m long and 2.2 m high, equipped with self-advancing supports. The model design was also conceived to accomodate eventual modifications of the space of the caved goaf as imposed by the actual conditions.

Jan 1, 1980

By Peter J. Tarkoy

The art of predicting rock excavating machine performance has become increasingly detailed and refined. Researchers using laboratory experiments and machine manufacturers using field observations have identified and defined mechanisms of failure, rock and tool interaction, and relevant design principles affecting them. Concurrently, practitioners have developed index tests which reflect rock properties relevant to machine performance. Empirical relationships between index properties and machine performance (penetration rate, cutter consumption, and machine utilization) have been established from past experience and are currently used throughout the industry. Contractors have used such relationships for estimating throughout the world. The detail in which geological, geotechnical, test, and project data, empirical relationships, and construction experience are utilized, is limited by time constraints imposed by the bidding period. To fully utilize all available data, methods of analysis, and construction experience, a simple computer program was developed for a microcomputer costing less than $7500. As a result, 1. machine performance predictions are detailed & reliable, 2. construction alternatives may be examined, 3. anticipated conditions & performance are graphically, documented & easily comparable to those encountered, and 4. results include a listing of assumptions & results of performance analyses & a graphic performance summary.

Jan 1, 1979

By Julie Mitchell

The U.S. Bureau of Mines is conducting research on the application of expert sys tens technology to mining equipment diagnostics and predictive maintenance, to increase mining productivity and efficiency. One of the greatest hindrances to mining productivity is the breakdown of equipment, causing lengthy and costly delays. A diagnostic maintenance expert system (DIMES) is being developed for the hydraulic system of a continuous coal mining machine. Through the use of such a system, the frequency of equipment failures and repair time should be significantly reduced. This paper describes the application domain, the functional requirements, and the problem approach for DIMES, the design and implement at i on of the knowledge- based system, the sensor work involved with the project, and the future plans for the continued development of this and other expert systems.

Jan 1, 1989

By D. W. Ashman

Today the electrolytic zinc industry is facing unprecedented environmental pressure and low metal prices. Zinc plants have to decide how they will dispose of iron residues in an environmentally friendly way without major capital expenditures. Only low-cost producers will survive, so companies must continuously improve to stay competitive. Therefore, the challenge of the process engineer is to find innovative solutions to the industry's problems. This paper reviews the status of electrolytic zinc processing and provides some insight into how the industry will respond to the pressures facing it

Jan 1, 1993

By Keith Whiting

The Van Stone zinc-lead mine is located in northeastern Washing- ton in Stevens County. It is about 24 km (15 miles) south of the Canadian border and 48 km (30 miles) west of the Idaho line. The deposits occur in late Cambrian age limestones and dolomites of the Metaline Formation. The bedding controls the trend of the zones containing the lenses of zinc-lead mineralization. The Van Stone property and vicinity is almost entirely covered with glacial drift averaging perhaps 6 m (20 ft) in thickness. Outcrops are very sparse. Outcropping gossan with zinc mineralization was first discovered by George Van Stone in 19 13, in what is now known as the South Ore Zone. Only minor trenching was done at that time. The property was idle until the mid- 1920s when Hecla Mining Co. drove several short adits and performed minor diamond drilling. In 1938, Willow Creek Mines of Nevada Inc. acquired the Van Stone plus adjacent parcels and commenced drilling on the known South Ore Zone. In the course of an expanded drilling program, the nonoutcropping North Ore Zone was discovered and was drilled out along a N30°E strike for about 305 m (1000 ft), beyond which point no mineralization was intersected.

Jan 1, 1991

By William R. Nash

The scope of work for the fast track construction of the Weeks Island Replacement Facility, Weeks Island, Louisiana included the design and construction of two salt mines. Mine #1 - An interim underground mining level consisting of a 975 m (3200 ft) incline and 3520 m of 5.5 m x 7.3 m (11560 ft of 18 ft x 24 ft) drill and blast excavation; raise boring; core drilling; roadheader excavation; complete bulk material handling facilities utilizing an existing production shaft. Mine #2 - Simultaneous with the interim mine construction a new one million ton per year underground salt mine was constructed consisting of: two 5.5 m diameter x 381 m (18 ft diameter x 1250 ft) deep shafts; 76450 cu m (100,000 cu yd) of drill and blast bottom excavation; surface and undergound bulk material handling systems (conveyors, skip loaders, shaft equipment, hoisting); ground freezing for water control for both the production and service shafts; the design of the first underground doublewall slipform installation of a dynamic bitumen shaft lining system; the emergency grouting of both the existing production shaft and the interim mining level in the salt dome; 227 mt x 64 m (250 ton x 210 ft) high structural steel production headframe; 2.2 MW (3000 hp) double drum mine hoist; service shaft headframe; and service buildings.

Jan 1, 1987

By I. S. Parrish

Reserve audits have increased in recent years as more companies, especially juniors, enter the ranks of producers. Corporate and individual investors are seeking corroboration of stated reserves. The reserve audit satisfies this need. An audit assures investors that the reserves, as presented, are a reasonable and accurate approximation of the quantity and grade of the economically viable material present. The reserve audit verifies that there are no fundamental errors in logic, style or the data base, and that the reserves, as given, may be used for mine planning or economic forecasting. Reserves that pass an audit may be used with confidence in preparing cash flow projections and in deriving net present value or internal rate of return on any given project. This article describes what a consultant does while performing the reserve audit. In performing an audit there are four general areas of concern that must be checked: definitions, parameters, data and procedures. In each of these, the auditor must convince himself that the reserve study has complied with governmental regulations and guidelines, professional standards and industrial practices. Any deviation from these norms must be identified and its effect upon the appropriateness of the reserves evaluated. By concluding that a reserve study passes his audit, the reviewer is stating that there are no fundamental errors in logic or style and that spot checks have revealed no substantive errors in procedure or mechanics. The responsibility for the reserves remains with the entity that compiled the original study.

Jan 1, 1990

By A. Sfougaris

A study on fauna distribution and abundance is being conducted in the Giona Mountain, in central Greece, area of bauxite mining. The specific aims of the study are: a) to estimate and map the distribution of mammals, and especially of the Balkan chamois, b) to estimate and map the distribution and abundance of breeding birds, c) to count the bird species using the area during spring and autumn migration and winter, d) to update the list of mammal and bird species of the mountain, with emphasis on rare and endangered ones, according to 79/409, 92/43 EU Directives and other relevant conventions, e) to compare the bauxite mining areas and species distribution and assess the possible overlap and compatibility of mining activities - species conservation, f) to assess the possible habitat loss due to planned mining activities. All estimations of mammal species distribution and abundance are being carried out by fieldwork using spotlight during the night along selected routes. Especially for chamois, line transects and vantage points with the aid of telescopes and binoculars are being used. Birds are being counted with the point count method in randomly selected plots distributed in all available habitat types and altitudes. The species distribution and mining areas will appear on thematic maps with the aid of a geographical information system (GIS). Finally, solutions for environmentally compatible mining activity in the area will be proposed.

Jan 1, 2007