Search Documents

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed. The work input is given by the following equation: [111W = 1 Owi( FP FF(1)] where W is the The energy input to the mill, (kWh/st); F is the Feed size based on 80% passed, (µm); P is the Product size based on 80% passed, (µm); and W; is the Work Index, (kWh/st) Methods to determine the Bond Work Index Various methods have been proposed by Bond to determine the Work Index. There are some problems with the Standard Bond Grindability Test: •Requiring a special mill. •Requiring a relatively large amount of sample. •Being relatively time consuming and tedious. [ ] During the recent years, numerous attempts have been made to install faster and easier methods to determine the Work Index. A complete description of these methods is presented by Yap et al. (1982). Determining the Bond Work Index by a new size ball mill During the recent years, researchers at the University of Tehran determined the Bond Work Index, using the Anaconda simplified methods by its Denver 305- x 127-mm (12 x 5-in.) laboratory wet ball mill. The equation used to calculate the Work Index for the above mill containing 16.12 kg (35.5 lbs) of steel balls is as follow: [1 _ 1-1W;=0.54x [P [)(2)] In addition, an attempt has been made to determine the Bond Work Index similar to standard Bond ball mill procedure but by a different ball mill, smaller and in consequent portable and less laborious than the Bond ball mill. Method description Just as the standard Bond grindability test, this method is a locked-cycle dry grinding and screening process that is carried out until steady state condition is reached. Test equipment The test is conducted in a special ball mill, called the New Size Ball Mill (NSBM). The mill is scaled down with a coefficient of two-thirds from the standard Bond ball mill. It measures 200 x 200 mm (8- x 8-in.) inside (instead of 300 x 300 mm or 12 x 12 in. in Bond ball mill). Just like the Bond

Jan 1, 1995

By John L. Bolles

The mineral processing engineer must have some knowledge of mineral identification, and the greater his knowledge in this field, the greater will be his potential to do his own specialty well. Most metal-bearing ores and industrial minerals require processing of some kind to produce a salable product or a material suitable for further processing. The types of treatment are many, but each one is aimed at separating a mineral or family of minerals from others. Obviously, then, it is basic to all mineral processing to identify the minerals present in the raw material and in intermediate and final products resulting from processing. Very often the mineral processing engineer will enter planning while exploration of a mineral prospect is going on. He will examine hand specimens, drill cores and cuttings, bulk samples, and materials in place. He must identify the valuable minerals, their occurrence and associations with other minerals, and the identity of diluents or host rock. An exact and detailed knowledge of the raw material will usually suggest the treatment processes that should be investigated in the development of the most suitable scheme for that particular raw material in that particular location. Physical properties of a mineral often lead directly to a process for separating that mineral from others. Some well-known examples of these are: magnetic separations for such minerals as magnetite, rutile, ilmenite; gravity separations for gold, silver, galena. cassiterite; flotation separation for most sulfides; distillation of mercury from cinnabar; and selective dissolution in specific solvents such as halite or sylvite in water, gold and silver in cyanide solutions, copper oxides, carbonates, sulfates and silicates in dilute sulfuric acid. These processes and many others are described in detail elsewhere in the Hand¬book and so it is not appropriate to give details here, except to emphasize that processing is aided greatly by complete mineral identi¬fication. Developing a treatment scheme for a new mineral discovery is an exciting assignment fag the mineral processing engineer, but much more of the usual work relates to quality control in existing plants. Here too, mineral identification is important. Some processing is aimed toward producing an end product which will meet exacting specifica¬tions regarding purity or allowable diluents. In this situation it is vital that contaminants be identified so that the process can be adjusted

Jan 1, 1985

By Joseph Alexis

Humphreys Engineering Co. has been associated with mining and milling since the turn of the century, but its greatest contribution to the industry was development of the Humphreys spiral concentrator in 1943. Few devices in the history of mineral beneficiation have been so uncomplicated. The spiral concentrator has no moving parts and requires no power except that needed to deliver slurry to the feed box, a requirement common to all concentrating devices. Although Humphreys Engineering Co. produces several models of spiral concentrators, the one -commonly used for coal cleaning is Model 24C-6 which has a flatter pitch than most other models. The spiral concentrator consists of a spiral conduit with a modified semicircular cross section. A slurry containing 20-35% solids by weight is fed to the feed box at the top of the spiral and flows downward. The heavier refuse particles concentrate along the inner side of the slurry stream and the lighter coal moves to the outside. The coal spiral has six complete turns-each turn consists of three 120°-sections and each section has a refuse port at the lowest point of the channel. The Humphreys spiral concentrator separates minerals in accordance with their physical properties (primarily specific gravity and particle shape). Aside from pumping slurry to the distributor, no energy is required to produce clean coal since the separating action is controlled by gravity. As slurry flows down the spiral channel, each particle is subjected to a centrifugal force, tangential to the channel. This force piles slurry on the outer rim of the spiral until the flowing stream reaches an equilibrium between outward centrifugal force and downward gravitational force. Once established, the stream position is relatively constant. In any flowing stream, differential velocities are present within that stream (the slowest fluid levels nearest the channel surface and the fastest layers at the center). As the channel curves, the lower slurry levels, retarded by friction, have much less centrifugal force and tend to move sideways toward the inner radius of the channel. As the bottom layers move inward along the bottom of the channel, the upper layers must move outward to maintain equilibrium. This cross sectional rotation separates the minerals and moves those of highest specific gravity toward the inner radius where they drop through refuse ports (see figure on following page). The simplicity of the spiral concentrator is apparent in operation. After tonnage, slurry volume, and percent solids of the feed have been determined-generally with laboratory testing-the operator's main concern is simple adjustment of the splitters located in the refuse ports. These splitters control the amount of refuse collected and, generally, once properly set they need little attention unless grade conditions drastically change or trash builds up and hinders laminar flow. Spiral concentrators are not overly sensitive to changes in pulp densities, variances in grade, or parti¬cle size and shapes. All these conditions may fluctuate over fairly wide ranges without adversely affecting recovery and product grade. In certain applications, desliming may improve recovery.

Jan 8, 1980

By Adrian Smith, Debra W. Struhsacker

13.1 INTRODUCTION Cyanide is, a generic term indicating the presence of the cyanide ion (CN-). Cyanide is a very common, naturally occurring compound produced by many biochemical reactions. Many plant species synthesize organic compounds which contain cyanide in the form of cyanogenic glycosides (Knowles, 1976). For example, trace amounts of cyanide are present in the seeds and leaves of many members of the Rosaceae (rose) family (Kingsbury, 1964). Many common items such as lettuce, maize, sweet potatoes, kidney beans, (Oke, 1969) almonds, and cigarette smoke contain cyanide. As examples, a recent chemical analysis of chocolate-covered almonds measured a total cyanide content of about two ppm (Steffen Robertson and Kirsten, 1987); and the U.S. Surgeon General (U.S. Department of Health, 1964) has shown that cigarette smoke contains up to 1,600 ppm total cyanide. The chemistry of cyanide solutions is complicated because the cyanide ion forms compounds and complexes with many elements. Some cyanide species are highly toxic whereas others are relatively inert and harmless. Molecular hydrogen cyanide (HCN) is the most toxic form of cyanide. Under most conditions, HCN exists as a gas which readily dissipates or reacts with the environment to form less toxic or nontoxic forms of cyanide. Thus HCN is an ephemeral toxin, and many naturally occurring geochemical processes reduce the HCN concentration of a heap system with time. As discussed below, free cyanide includes the two species, ionic cyanide (CN-) and molecular hydrogen cyanide. Free-cyanide toxicity in man, mammal s, and aquatic species is we1 1 documented (Doudoroff, 1976; Ecological Analysts, 1979; Towill et al., 1978). The lethal doses reported for human adults vary with the type of exposure as follows: • One to three mg/kg body weight if ingested; • One hundred to 300 ppm if inhaled; and • One hundred mg/kg of body weight if absorbed. Acute toxicity of free cyanide to freshwater invertebrates ranges from 0.028 to 2.295 mg/l, depending on species and test conditions. Generally, free-cyanide concentrations greater than 0.1 mg/l are expected to kill sensitive species in freshwater or marine environments (Doudoroff, 1976;

Jan 1, 1988

By Paul L. Russell

Numbers, arithmetic, mathematics. Where did it all come from? Who needs it? We all do, but many school children would not agree. Engineers, physicists, accountants, tax collectors, and most of the general public are well aware that modern society in large part is founded on mathematics and could not exist without it. Mathematics developed over thousands of years as part of the everyday life of man. No one area, tribe, or race can claim discovery. In fact, from the records that do exist, it is evident that many facets of mathematics were discovered independently of others who made similar discoveries. While proof may be lacking, the earliest concepts of mathematics may be some 250,000 to 300,000 years old. The first use of numbers as written records is unknown. However, a bone of a young wolf deeply cut with 55 notches-arranged in two rows, one of 25 notches, the other of 30-was found in Czechoslovakia. Dated to be about 30,000 years old, it is perhaps an early record of some kind of counting system. It is assumed that mathematics was developed as an answer to man's practical needs, but anthropological studies suggest that the art of counting may have developed in connection with the needs of primitive religious ceremonial rites. Fingers probably were first used to designate sets of from one to five objects. Using both hands, up to 10 items could be indicated. As civilization developed, so did the need for more flexible systems to record items of trade, measure land, and figure taxes. Aristotle noted that the development of the decimal system comes from the fact that most people are born with 10 fingers and 10 toes. In spite of this obvious fact many early civilizations used binary, ternary, and quinary systems while vigesimal systems (with 20 as a base) and even sexagesimal systems (with 60 as a base) were used by others. A form of writing was in use in both the Mesopotamian and Nile valleys as early as 3000 to 4500 B.C. In Mesopotamia, wedge-shaped marks were impressed upon soft clay tablets that were hardened in ovens or by the sun. Many thousands of such tablets have survived. When the tablets were finally deciphered, some were found to be records of items shipped in trade, inventories, tax accounts, and mathematics exercises for teaching. Mesopotamia is also the source of an interesting board game dating back to about 2500 B.C. Its buttonlike men and triangular dice were apparently used with squares of shell, inlaid with lapis lazuli and red sandstone. Unfortunately, rules of play were not found. In Egypt, record preservation was somewhat better. Discovery of the Rosetta Stone in 1799 eventually led to deciphering the Egyptian hieroglyphics that included a numbering system at least 5,000 years old. These records show a competence in counting and numbering. A calendar of good accuracy may have been in existence as early as 4,200 years ago. Mathematics, as practiced today, developed when the Greeks added logic and proof to arithme-

Jan 12, 1982

By Louis J. Sousa, Elizabeth H. Yaremchuk, Annette P. Graham

Introduction Responding to Congressional inquiries regarding the purchase of a number of major domestic mining and metals companies by foreign firms, the US Bureau of Mines examined trends in foreign direct investment in the US. mining and mineral processing industries1. "Foreign Direct Investment in the US Minerals Industry" analyzes the extent of foreign investment in several major mineral commodity industries. It identified the countries of origin of foreign investment in US mineral assets. The study also described several reasons for the growth of foreign investment in US minerals and discussed some potential implications of this activity. Foreign investment trends in the economy and minerals For the economy as a whole, between 1977 and 1985 the number of US affiliates of foreign investors more than doubled - from 4046 to 9824 - as did employment at these affiliates - from 1.2 million workers to 2.9 million (Table 1)2. During this same time period, the total value of assets of all US affiliates throughout the economy rose from $239 billion to $736 billion (1985 constant dollars). In the domestic minerals industry, foreign investment also grew substantially during that same time as the number of US minerals-related affiliates increased by 74% - from 125 to 217 - between 1977 and 19853. During the same period, employment at all foreign-owned affiliate mineral operations in this country increased by 78% and totaled 198,000 workers at the end of 1985. Parallelling the growth in the number of and employment at foreign-owned US mineral and metal operations, the total value of US mineral assets owned by foreign firms (or individuals) has nearly doubled since 1977 and amounted to $30.9 billion at the end of 1985. The rate of increase in foreign investment in US mineral assets was slightly higher in the metals industries than in the nonmetallic groups. Foreign investment more prevalent in minerals Perhaps a more useful way of evaluating the growth in foreign investment is to analyze growth in the "intensity" of foreign investment - the proportion of total US industry assets held by foreign investors. Although insufficient data on total industry assets prevented the development of such a measure, employment data provide an indication of relative differences in the intensity of foreign investment among the mineral industries and other industries. For example, as noted in Fig. 1, the 198,000 minerals industry workers employed at US-affiliate companies in 1985 represented 12.7% of total employment in this sector of the economy. In comparison, for the mining and manufacturing sectors of the economy as a whole, 7.8% of all workers were employed at US-affiliate firms in 1985. For the total economy, 2.7% of the entire civilian employed workforce worked at US-affiliate firms that year. Using employment as an indicator, foreign investment has been more prevalent in the minerals industry than in most other industries. About one worker in eight in the minerals sector was employed at a US-affiliate firm in 1985. In comparison, for the goods producing sectors of the economy - all mining, petroleum, and manufacturing industries - about one worker in 13 was employed at a

Jan 8, 1988

By James F. Archibald, Ferri Hassani, Jacques Nantel, David O. DeGagné

Operators depend upon the success of backfilling programs to ensure that mine activities run continuously (Archibald et al, 1993) where backfilling is an integral part of the mining cycle. In order to ensure that the backfill is prepared and delivered to the stope possessing the required engineering properties, as designed, and that the backfilling process is safe, mine operators at all stages of the backfilling system must be adequately trained for their tasks and be aware of how their work affects other backfilling stages, both up- and down-stream of their station. Mine operator training is primarily based on learning on-the-job from experienced supervisors or training personnel. Classroom training and the availability of reference manuals are less common. While in use by many industries for some time now, computer-based training (CBT) is becoming more readily accepted by the mining industry for a wide variety of training. It is not intended to replace on-the-job training, but to augment it. CBT offers many advantages to enhance operator learning by utilizing multimedia presentations, interactions and on-line testing to teach complex concepts and relationships. Discussions with many operations revealed that there is an industry need for a backfill guide for frontline operator training and as a reference manual for operators and mine engineers. Sponsored by the mining industry and the CIM, "Mine Backfill, An Operator's Guide" has been developed by the Departments of Mining Engineering at Queen's University and McGill University to fulfil this need. "Mine Backfill, An Operator's Guide" is an interactive multimedia package that incorporates high quality colour images, animations, sound, and video with text to review the main backfill methods employed in Canada, including hydraulic/slurry, paste and rock fill. The Guide is divided into training and reference primer sections. When in training mode, the operator is guided through a presentation of common mining and backfill practices and technologies so that he/she may become more familiar with different aspects of backfill processes. To ensure that key concepts have been learned during training, the operator will be tested after each section using a series of multiple choice and true/false questions. When in reference mode, alternatively, the operator may browse through the information in a more detailed and independent fashion through a series of interactive menus. The Guide focuses on the following main topics: resources, surface preparation, distribution, stope activities, health and safety, and quality control. Special features included in the Operator's Guide are a Buyer's Guide, a Trouble Shooting Guide, and an interactive glossary of backfill and mining terms. Concepts in interactive and computer-based learning are also reviewed in this paper.

Jan 1, 2001

By Surendra K. Mishra

The increasing volume of wastes being generated by industry is a legacy of the industrial revolution and subsequent industrial growth. Social and regulatory pressures have been mounting on industry to improve its waste management practices. In many industrial sectors, waste disposal has been the only method of waste management. Land farming, underground burial, deep wells and incineration are still practiced. Often, concentration and volume reduction of waste streams are also practiced to reduce the waste management costs. In the recent years, there has been emphasis on waste minimization. Since the 19th century, industry has practiced recycling of usable resources as a way of handling unwanted byproducts. The mining industry has recovered or extracted economic minerals from tailings for decades. For example, during the gold rush period of 1970s, extraction of gold from tailings dams became economically attractive. Similarly, when it was economical, coal and shale fractions have also been recovered from tailings and refuge materials for commercial uses. In the steel industry, with the development of new furnace technology, recycling of flue dust and scrap iron was practiced as early as in the 19th century. Before 1900, there was little incentive for the industry to reduce the waste volumes. Manufacturers, however, did see a rationale for adopting profit-increasing techniques. They made an effort to recover and recycle economic materials from waste sources. One of the pioneering examples of resource recovery is the coke making industry. As the industry was market driven, products recycled from coke batteries included ammonia for use in fertilizers, gas for power generation and heating, and tar for road construction, wood preservation and roofing. Tar had been avery troublesome waste byproduct. But it quickly became a valuable chemical raw material, providing the foundation for Germany's dominance of the world's dye and medicine markets before World War I. Similar trends evolved in the chemical industry. In the context of current environmental regulations and escalating mining and processing costs, recycling of re- [ ] sources is becoming economically more attractive. Solid and liquid wastes generated by industries contain a range of inorganic and organic contaminants. Among these contaminants, metals and hydrocarbons form major groups. Treatment of these wastes is essential to meet regulatory disposal requirements. In the recent years, based on the principles of chemical and mineral process engineering, processes have been developed to treat these industrial wastes. This article reviews some of the processes that have made impacts and have proven to be effective at commercial scales.

Jan 1, 1999

By Robert D. Brown, Charles A. Sorrell

The decade of the 1980's saw "advanced materials" become a key factor among the industrialized nations, with the United States, Japan, and the European Economic Community being the major competitors. All three have identified communications technology, advanced materials, and biotechnology as the keys to future industrial leadership and the closing decade of the 20th Century is expected to be an era of rapid development and restructuring. The progress of EC'92, the effort to develop uniform standards and remove trade barriers in Europe; the determination of Japan to commercialize advanced structural ceramics, alloys, composites, and superconductors; and the emergence of less developed countries as major supplies of commodity materials pose enormous challenges to the position of the United States as an industrial and financial leader. A consensus is developing that the industries that are first to commercialize the large array of new structural materials and electronic, optical, and magnetic materials and devices will be those who determine the structure of national and world economics. Many technical, economic, legal, political, social, and cultural factors are important determinants in the race to commercialize new materials. Millions of words have been written about these factors and their interdependence; yet the sheer complexity of the problems, the rate at which changes are taking place, and the economic risks involved are so great that government policy makers and industrial decision makers find adequate understanding to be very difficult. Of the many factors involved in advanced materials, the Bureau of Mines has the statutory responsibility to provide information on where materials can be found and how they are mined, extracted, purified, combined, and recycled. It is obvious that minerals availability is essential to implementation of any new technology just as there can be no commodity metals industry if the ores are not available. Because "minerals availability" for commercialization of advanced materials and devices is more complex than for commodity materials and a new mix of materials and processes is emerging, the Information and Analysis Directorate of the Bureau of Mines is redirecting resources to provide reliable information for policy and decision making. The Office of Advanced Materials Coordination (OAMC) was established as a staff operation in July 1987 to assist the efforts of the divisions and branches. The key issues and problems were defined and the role of the Bureau was outlined (Sorrell, 1987, 1988). In February 1990, the functions of OAMC were transferred to the new Branch of Advanced Materials, a line organization parallel with the Branches of Ferrous, Nonferrous, and Industrial Minerals, and was given the responsibility for developing new methods to acquire, analyze, and disseminate information about new materials. The purpose of this paper is to provide definitions, a summary of major issues and problems, an overview of minerals and processing availability problems, and a perspective of the ways in which the mining and materials industries can help to ensure domestic availability of raw and processed materials.

Jan 1, 1990

By William J. Taylor

Strictly defined, a stull is an inclined or horizontal timber support; a vertically placed timber is defined as a prop. Common usage allows the catchall term "stull" to refer to all such uniaxial mine support, regardless of orientation. Typically a stull is a round wooden column that is wedged in place to provide short-term auxiliary support between sill and back, or between hanging wall and footwall. Stulls may be used exclusively or in con- junction with other support systems such as roof bolts, shotcrete, or cribbing. Stulls are used both as local temporary support in stoping operations and for uniform systematic support installations. Where stoping areas are to be abandoned soon after excavation, stulls may be used to provide temporary support during mining operations. Where controlled caving and subsidence is required, stull supports are designed to fail in a systematic, predictable manner. Wood type is selected on the basis of availability, price, and load carrying characteristics. Coniferous woods are typically used, especially to carry heavy ground loads. Brittle woods are generally avoided because of their tendency to fail suddenly. Gradual yielding failure is preferable to sudden, unexpected failure of the support. Some usage of wood from deciduous trees such as cottonwood and other poplars has been reported in Grants, NM. These stulls reportedly mushroomed as the ground load increased but continued to maintain their structural integrity. Stulls fabricated from structural steel are used in special applications. Adjustable lengths are commercially available in mechanical, hydraulic, and pneumatic designs. The high cost of mechanical stulls limits their use to mining systems where recovery and reuse is possible. End blocking, also called headboards or footboards, uses wood blocks that are placed between the stull end and the ground they are supporting. The blocks are typically 50.8 to 101.6 mm (2 to 4 in.) thick, 203.2 to 304.8 mm (8 to 12 in.) wide, and 381 to 609.6 mm (15 to 24 in.) long. End blocking serves to distribute the support over wider back area. Compression of the end blocking gives visual indication of wall movement prior to failure of the stull. A common application of the stull is in flat-bedded uranium mining during pillar extraction. Many western US uranium mines use a pillar pattern development to delineate the irregular ore pods. After development of an appropriate sized pillar, the ore pillars are then sequentially mined out, leaving the undercut hanging wall or back to cave. Where thickness of the ore is less than 4.3 m (14 ft), stulls are generally used to provide ground control as the pillar is removed in slices. Experience dictates the density of stull placement. In general, the number and size of stulls should be sufficient to resist ground closure and to provide support for drilling and loading operations adjacent to the pillar. Stulls next to the mining face are often lagged 0.9 to 1.2 m (3 or 4 ft) up from the floor (or sill) to confine the blasted ore to a passage next to the pillar. Mucking is simplified by this confinement. Experience dictates whether back control along a mining face requires removal of stulls to allow con- trolled subsidence of the back or hanging wall. Without caving or closure, abutment pressure can create poor ground conditions near the pillar.

Jan 1, 1982

By M. Measures, W. A. Napier, C. Pomroy, J. M. Jardine

INTRODUCTION In most uranium mines the concentration of uranium in the ore is low enough that inhalation of dust does not present a radiological problem. Conversely in the mills there is a potential inhalation hazard from inhaled uranium in concentrated form, namely "yellowcake" and other compounds intermediate between the ore and the final product of the mill. It was generally assumed that the solubility of yellowcake placed it in the category of Class D materials. This plus the fact that the uranium is non-enriched led health physicists to assume that the potential health hazards were a result of the uranium's chemical properties rather than its radiological properties. Bioassay programs have thus been limited to routine urine sampling at a weekly or monthly frequency. In most cases when a high reading was obtained, subsequent sampling within one or two days showed a rapid return to low levels, therefore tending to confirm the class D nature of the material. Two developments over the last few years have however suggested that modifications to this simple bioassay program may be necessary and practical. Firstly, a number of studies on the solubility of uranium mill products, from ore to yellow cake, in simulated lung fluid (Eidson A.F., Mewhinney J.A., 1980) have shown that some of the material is not class D, but class W or even Y. This raised the possibility that, while the urine levels rapidly decreased, indicating rapid excretion of the class D component, the W and Y components remained in the lung. Thus an unsuspected lung burden could have been accumulated. The second development, the ready availability of [in vivo] counting facilities with which to make direct measurements of uranium lung burdens, offered a means of confirming the hypothesis of unsuspected lung burdens. A study was therefore initiated to correlate lung burdens with urinary excretion. METHOD A total of 79 subjects from 3 uranium mills participated in the study. They were brought to the Ottawa laboratories of the Radiation Protection Bureau in groups of 4 or 6, over a period of several months. In Ottawa, [in vivo] thorax measurements were performed, and a urine sample collected. Each subject also brought with him a urine sample that had been collected the previous day. All samples were split, for analysis by both R.P.B. and the mill laboratory. [Concentrations of Uranium Dust] Results obtained by mills A, B and C for concentrations of uranium in air at various locations are given in table 1. Samples taken at mill B were obtained using continuous sampling with a midget impinger over a six hour period. Samples taken at mills A and C were 5-minute gravimetric samples. [Subject Selection] The subjects were selected to represent a wide range of work history in terms of both length of employment and type and location of job, as shown in table 2.

Jan 1, 1981

By Nora M. Hutt, Kevin A. Morin

The Sobek humidity cell has been in use with minor modification for more than 30 years to determine bulk primary-mineral reaction rates. As a result, it has become a key tool for predicting the bulk rate of sulphide oxidation, the Carbonate Mole Ratio (CMR) of neutralization-potential (NP) consumption to sulphide oxidation, and the rates of metal leaching. Most humidity cells are operated for less than a year, with the resulting rates extrapolated into the future for years or decades. The validity of these extrapolations was tested by examining longer trends from cells that have operated for three to seven years, as found in the International Kinetic Database (IKD). Additionally, large batches of cells for two minesites in the IKD (45 and 46 cells each) were examined to determine if regular, predictable trends were obtained across ranges of geochemistry at a minesite. The long-term cells show that the rates of sulphide oxidation and acid generation, based on sulphate production, have a 50% chance of stabilizing within one year, with the remainder fluctuating significantly throughout their test periods. Despite the fluctuations, the CMR, which is critical for defining site-specific or rock-unit-specific ABA criteria, remains relatively steady in many cases between 1.0 and 2.0 as expected from principles of aqueous geochemistry. However, if the sulphate-production rate falls below 10-30 mg/kg/wk, the CMR value can increase significantly. At and below these low rates, physical factors like flow rates of surface waters and groundwaters will determine the rate of NP consumption, rather than geochemical factors. Also, if weekly rinse pH falls to acidic values, the CMR will decrease below 1 .O, reflecting the exhaustion of fast- neutralizing minerals. The two batches of multiple cells also confirm these trends across arange of geochemistry. The long-term cells show that copper leaching often stabilizes within a narrow range as long as rinse pH remains relatively constant. Also, there is no strong dependence of leaching on the sulphate rate. However, the rate of copper production often increases sharply if rinse pH falls to acidic values. This suggests the measured copper-production rate in some cases is not a true primary rate, but a lower secondary rate after secondary- mineral precipitation within Sobek cells. As with the long-term cells, the batches of multiple cells show that copper production often increases gradually with decreasing rinse pH, with no clear dependence on sulphate production. However, high rates can also occur at near-neutral pH, so secondary-mineral precipitation of copper is not necessarily common.

Jan 1, 2000

By Thomas A. Boyce

Introduction Although innovative coal extraction technology can be approached from many angles, this paper focuses on three: innovation in response to rising costs, to changing mining conditions, and to regulatory issues. Before exploring these three subjects, however, a basic question needs to be raised. Why Innovation? Coal is widely heralded, and quite correctly so, as the United States' "ace in the hole." It has been said that the U.S. is to coal what the Arabs are to oil. The implication is that we have nearly inexhaustible reserves - that coal is cheap, plentiful, and easy to extract. Indeed, because our current productive capacity is estimated to be 15-20% greater than demand, we have been given a false sense of security about the ease of future coal extraction. Therefore, innovative measures are being concentrated on developing technologies for the demand side of coal, including power generation, synthetic fuels, and industrial applications. What is often forgotten is that the unit cost of producing energy from these new technologies depends critically on the cost of the coal feedstock -in some cases the coal consumed accounts for more than one-third the total cost. Thus, while the developers of the end-use technologies struggle to improve the overall thermal efficiency of their process by one or two per¬centage points to make the energy produced competitive in the marketplace, they often are unaware of the risk of a 3 to 6% increase in coal costs wiping out the expensive, hard-earned results of their research. Energy planners are just beginning to realize that coal is not a uniform commodity available at low cost in infinite quantities. Coal is a heterogeneous material whose cost and quality vary widely with local conditions. To produce the massive amounts of projected coal-based energy at reasonable costs, we urgently need devel¬opments in extraction technology, as well as in end-use technology. Thus, coal extraction, coal conversion and utilization, and end -use energy consumption must be viewed as highly interdependent parts of an energy supply network (Fig. 1). And current emphasis on conversion and utilization must be balanced by more emphasis on upstream technologies, including coal extraction. Even more important, the impacts of innovation (or the lack thereof) in any one technology area in the energy supply network need to be discussed and understood by those working in each of the other areas. Why innovation in coal ex¬traction technology? Figuratively, we are all in the "coal boat" together - geologists, miners, transporters, processors, power producers, distributors, and consumers. Innovation is required from each of these sectors to overcome the obstacles that prevent greater use of our most abundant national energy resource. All other links in the coal energy supply network depend on large volumes of coal produced at reasonable costs. Declines in productivity, therefore, must be reversed; the more difficult mining conditions that will be encountered call for new methods and equipment, and regulatory issues must be resolved if the coal ex¬traction link is to be a strength rather than a weakness in the planned U.S. transition to an economy based more on coal and less on imported petroleum. Innovation Tailored to Regional Conditions Once the importance and urgency of innovative coal extraction technology has been grasped, the next step - implementing a research program - becomes quite

Jan 1, 1980

By Andrew J. Regis

The methods of evaluation of industrial minerals occurring on Federal lands have different meanings if the evaluations are done by a company rather than a government agency. For example, when the Bureau of Land Management (BLM) conducts an examination of mining claims, this is commonly referred to as a "validity examination," whereas it is an "economic evaluation" when performed by a company. Not only is there a difference in nomenclature in these evaluations, but there is a general lack of expertise in the Federal government on industrial minerals in general. A metallic mentality still prevails in the U.S. Forest Service (USFS) and the BLM. Because of this, many validity exams on industrial-mineral deposits commonly just skim the surface concerning economics and marketability. The BLM and USFS place a high amount of emphasis on past administrative case law pertaining to the validity of industrial minerals under the 1872 Mining Law and, rightly so, on marketability, which also is heavily addressed in case law. When the BLM considers marketability, only the marketability of a particular industrial mineral for only the primary use for which it was located is considered and any value-added markets cannot be included. The BLM defines marketability based only on the value of the mineral material in its in situ or raw state, rather than value-added through processing. Another difference in the evaluation of industrial minerals by government and industry is the question of by-products. When a company evaluates a mineral material it looks at all the markets. The BLM looks only at that market for that locatable mineral for which the claim was located. In other words, sales from non-locatable by-products cannot be used to support marketability or the prudent-man rule (i.e., oversize silica sand from a glass-sand claim being sold for construction sand, road base, fill, etc.). The question of reserves also can present conflicts. An industrial-mineral company will often try to identify all the reserves available for a possible future development. They must do this for financial backing and support from upper management. The BLM, however, will limit their validity examination only to those reserves that meet the prudent-man rule and marketability tests. The BLM will validate reserves sufficient to last 25-30 years, based on available market. The development of industrial minerals on Federal lands is a difficult process, and, if the 1872 Mining Law is changed, it could become not only more challenging but also more costly. The industry must become more tolerant of the mineral specialists in the BLM and the USFS. On the other hand, the government mineral examiners must become more aware of the importance of industrial minerals in everyday living, and the economic evaluation of these materials.

Jan 1, 1999

With the rapidly growing use of hydraulics in mining equipment, maintenance personnel should be familiar with the various components in hydraulic systems. Hydraulic systems do wear out - the fluids they transport are hot and turbulent, the equipment they power often imposes tremendous pressure pulsations and bending stresses, and the working environment is harsh. Therefore, even though hydraulic hoses are made of remarkably trouble-free components, they do need to be replaced periodically. There must be coupling methods that allow hoses to be replaced without disturbing other components. Couplings must also provide a variety of leak-resistant connections between hoses and other components in the hydraulic circuitry. Threaded Connection and Seals Hydraulic coupling thread ends and sealing arrangements are standardized, with many types available. Their outward appearance varies, but coupling configurations are recognizable by examining threads and seals and comparing them to the examples provided here. Iron Pipe Thread There are two kinds of iron pipe threads normally used in mining equipment circuitry - National Pipe Tapered Thread for Fuels (NPTF) and National Pipe Straight Thread Mechanical Joint (NPSM). The NPTF seal is the engagement of the coupling threads, called thread interference. When tightened, the tapered thread of the male fitting binds into that tapered thread of the female fitting to form a relatively leakproof seal (Fig. 1). In the NPSM seal, there is a 30° angle seat machined into the end of the male NPTF fitting. This seat engages with a mating 30° angle cone on the inside of the female fitting. Female NPSM fittings have straight threads, as opposed to the tapered threads of the NPTF fittings. However, most NPTF solid male fittings also have a 30° angle seat enabling them to be used with NPSM female fittings (Fig. 2). JIC and SAE Fittings Joint Industry Conference (JIC) and Society of Automotive Engineers (SAE) seals are formed by joining two mating, conical metal surfaces. The coupling threads are used to bring and hold these surfaces together to form a leak-resistant seal. A JIC connection is a solid male threaded end, with a 37° machined male nose, mating with a 37° female flare seat. When connected, the mating surfaces are held together by the threads, but the threads do not form the seal. The female seat is created by flaring a tube end or machining the interior surface of a stem to 37°. A female JIC has a swivel nut, allowing the sealing surfaces to be joined together without twisting a hose or twisting the seats against each other (Fig. 3). JIC couplings are frequently used on low, medium, or high pressure hydraulic circuits on mining equipment and machinery. The SAE connection is similar in appearance and sealing characteristics to the JIC system, except the angle of the machined male nose and female flare seat is 45° (Fig. 4). "O" Ring Fittings Seals for "O" ring fittings are formed by compressing an "O" ring against an exposed machined surface on a mounting block or hydraulic component part. The "O" ring must be compatible with the type of hydraulic fluid used (Fig. 5). An "O" ring boss connection is made of a male straight thread

Jan 10, 1983

By George McArthur

GEOLOGY One of the largest copper resources in North America occurs in the Bingham mining district, located 40 km (25 miles) southwest of Salt Lake City, UT. Anaconda's present contribution to the development of this resource is the Carr Fork mine. (Fig. 1, Bingham district plan map.) The Carr Fork story began about 300 million years ago when a thick sequence of sedimentary quartzite and limestone was deposited in the Oquirrh Basin. Subsequent earth stresses formed a series of west-northwest-trending overturned anticlines and synclines that were later offset by northwest-striking thrust faults and northeast-trending normal faults. (Fig. 2, Bingham district cross section.) About 38 million years ago the Bingham stock was intruded into some of the folds, resulting in the formation of porphyry ore in the intrusive, and fissure, replacement, and skarn ore deposits in the sediments. The Carr Fork skarns were formed preferentially in two limestone units, called the Yampa and Highland Boy, which average about 46 m (150 ft) in thickness, separated by about 76 m (250 ft) of quartzite. Copper mineralization consists almost entirely of chalcopyrite associated with pyrite and molybdenite in a gangue of garnet, diopside, magnetite, quartz, and carbonate. Molybdenum, gold, and silver are economic byproducts. (Figs. 3 and 4, indicated ore in plan and section.) EXPLORATION HISTORY The West Mountain mining district, of which Carr Fork is a part, was organized in 1863, after leaf-silver ore was discovered in the Carr Fork of Bingham Canyon. However, it was not until 1873, when the Bingham and Camp Floyd railroad to the town of Bingham was completed, that the mining camp flourished. Many small mining companies in the district were reduced, often through consolidation. By 1937 only the National Tunnel and Mines Co. was active in the Carr Fork area. In 1948 it declared bankruptcy, and was later purchased by The Anaconda Co. Anaconda conducted geologic investigations in the Bingham district until 1968, when a concerted diamond drilling program was initiated to fully evaluate the geologic potential of the Carr Fork area. The exploration program commenced with one diamond drill, but was enlarged to three drills following discovery of the first major ore intercept. Near completion of the exploration effort, large oil well rotary drills were used to drill to depths of 762 to 914 m (2500 to 3000 ft), after which the holes were completed by standard diamond drilling techniques. All holes were collared vertically, but considerable deviation occurred because of structure and rock conditions. Wedging and directional drilling were used to keep the holes on target and to provide multiple ore intercepts in the deeper holes. Geophysical surveys, in-

Jan 1, 1982

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumed metabolic rate of 325 W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ΔTgi and ΔHR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ΔTgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

Aquifer. A formation, group of formations, or part of a formation that contains sufficient satu rated permeable material to yield significant quan tities of water to wells and springs. Artesian. Synonymous with confined; see ground water, confined. Capillary fringe. The zone immediately above the water table in which all or some of the interstices are filled with water that is under less than atmospheric pressure and that is continuous with the water below the water table. Conceptual model. A conceptualization of a field hydrogeologic framework that facilitates the development of analytical field testing procedures. The results of the test(s) may force changes in the initial conceptual model. Conductivity, hydraulic. Replaces the term "field coefficient of permeability." The volume of water at the existing kinematic viscosity that will move in unit time under a unit hydraulic gradient through a unit area measured at right angles to the direction of flow, if the porous medium is isotropic and the fluid homogeneous. Confining bed. A body of "impermeable" material stratigraphically adjacent to one or more aquifers; its hydraulic conductivity may range from nearly zero to some value distinctly lower than that of the aquifer. Flow, steady. Any point where the magnitude and direction of the specific discharge are constant in time. Flow, uniform. At every point the specific discharge has the same magnitude and direction. Flow, unsteady. At any point the magnitude or direction of the specific discharge changes with time. Fluid potential. The mechanical energy per unit mass of a fluid at any given point in space and time with respect to an arbitrary state and datum; the fluid potential is proportional to the head. Ground water, confined. Ground water under pressure significantly greater than atmospheric; its upper limit is the bottom of a bed of distinctly lower hydraulic conductivity than that of the material in which the confined water occurs. Ground water, perched. Unconfined ground water separated from an underlying body of ground water by an unsaturated zone. Ground water, unconfined. Water in an aquifer that has a water table. Head, static. Height above a standard datum of the surface of a column of water (or other liquid) that can be supported by the static pressure at a given point. Homogeneity. Hydrogeologic properties are identical everywhere. Hydraulic gradient. Change in static head per unit of distance in a given direction. Hydrostratigraphic unit. A body of material having considerable lateral extent and comprising a geologic framework for a reasonably distinct hydrogeologic system. Isotropy. Condition in which all significant properties are independent of direction. Porosity. Property of containing interstices or voids; may be expressed quantitatively as the ratio of the volume of its interstices to its total volume. Porosity, effective. Interconnected pore space available for fluid transmission; expressed as a percentage of the total volume occupied by the interconnecting interstices. Potentiometric surface. A surface that represents the static head along a particular specified surface or stratum. Specific retention. Ratio of the volume of water that the rock or soil, after being saturated, will retain against the pull of gravity to the volume of the rock or soil. Specific yield. Ratio of the volume of water that the rock or soil, after being saturated, will yield by gravity to the volume of the rock or soil. Storage, specific. The volume of water released from or taken into storage per unit volume of the porous medium per unit change in head.

Jan 1, 1986

By D. W. Gentry

Introduction Until recently, there were many jobs for mineral engineering graduates. Traditionally, minerals-related career paths available to university graduates stem from rather standard offerings in the disciplines of mining, metallurgy, petroleum, geology, geophysical engineering, and mineral economics. Within each discipline, there exists many career opportunities. In fact, until fairly recently, the most difficult decision for most graduates was choosing among all the available alternatives. Unfortunately, this relative state of euphoria changed quickly and dramatically within the minerals sector. Within two or three years, graduates from minerals-related engineering disciplines found it exceedingly difficult - and then almost impossible - to secure employment in the minerals sector upon graduation. At the same time, there were dramatic reductions in production requirements and, ultimately, mine closings. This resulted in massive layoffs and often termination of professional personnel possessing significant and valuable industrial experience. Obviously, this worsened an already bad employment picture for those hoping to begin a career in minerals. Certainly, there is no universal agreement on what the future offers for the US minerals industry or the career opportunities associated with it. However, there are a number of considerations that deserve study by students, faculty, administrators, and industrial personnel before minerals-related career paths are chosen. Where Will the Jobs Be and How Many? Everyone is aware that the minerals industry is very cyclic. It is not surprising then that job opportunities for new graduates also fluctuate. Typically, there is a two-to-four year lag between industry's engineering manpower needs and the academic community's ability to produce this talent. Due to the response lag, there will necessarily be years when supply and demand do not match. Employment Projections It is extremely difficult to anticipate what the key career paths might be within the next few years. Considerable speculation remains with respect to whether activity in the US minerals sector over the short-, intermediate-, and long-term will improve, remain status quo, or further deteriorate. However, some information pertaining to the prospects for career opportunities in mining engineering was offered by Tingley and Ghose (ME, Sept. 1983, p. 1274) from a study performed by Fenvessy and Schwab. Results from this industry-sponsored survey suggest that the US will experience 700 more mining engineers than needed in 1985, 1300 in 1990, and 1800 in the year 2000. These conclusions were based on the assumptions that future graduate levels remain flat and demand increases 3.6% annually. Educators quickly argued that depressed job markets, coupled with university student mobility, would negate the assumption of flat mining graduate levels in the immediate future. Student Mobility Student mobility from one engineering discipline to another is high. This is perhaps best demonstrated by the tremendous growth in programs such as computer engineering and computer science at the expense of enrollments in the more traditional engineering programs. The ability and willingness of students to quickly change engineering disciplines in response to existing and perceived job market demands have created significant student, faculty, and resource dislocations within universities nationwide. This has resulted in problems for university faculty and administrators responsible for effective use of

Jan 2, 1985

By G. A. Swanquist

INTRODUCTION This article describes the yellow cake drying, packaging and dust collection circuit of the United Nuclear Church Rock Mill. It also describes the layout and floor plan of this section as well as the operation and performance of the various equipment. In order to place the yellow cake section in perspective of the mill as a whole, the mill circuit is described briefly. CHURCH ROCK MILL GENERAL DESCRIPTION The Church Rock Mill contains six operating sections shown in Figure 1 in block diagram form. The grinding section consists of a semi-autogenous mill in closed circuit with a hydrocyclone. The slurry is then routed to the leaching tanks. Sulfuric acid and sodium chlorate is added to dissolve the uranium. The pulp is transferred from the leach tanks to the thickeners where the uranium bearing liquid is separated from the barren solids. The uranium bearing solution is then filtered and pumped to the solvent extraction section. [ ] In the solvent extraction section, the uranium bearing aqueous solution is brought into contact with an organic solution composed of kerosene, amine and isodecanol. The amine extracts the uranium from the aqueous solution. This organic solution is then routed to the stripping section, where the uranium is removed from the organic solution with an ammonium sulfate aqueous solution. The pregnant stripping solution now concentrated to 30 gpl U308 is routed to the precipitation tanks where ammonia is added to precipitate the uranium. The yellow cake is then washed in a counter current circuit of two thickeners and one centrifuge to remove impurities, mainly sulfates in order to meet specifications. The centrifuge centrate is routed to the second wash thickener for forward wash. The centrifuge cake at approximately 50% solids consistency is transferred to the yellow cake dryer via a screw conveyor. YELLOW CAKE DRYING, PACKAGING AND DUST COLLECTION Figure 2 shows the flowsheet of the integrated circuit of drying, packaging and dust collection. This section of course centers around the yellow cake dryer as the main equipment. The other main units are the dust collectors for the dryer and packaging respectively, a yellow cake storage bin and the yellow cake packaging facilities. Physically, all of this equipment occupies four floors, beginning at the top floor: 1. Both dust collector fans, the centrifuge and the screw conveyor to transport the yellow cake to the dryer. 2. The dryer, fire box and both dust collectors occupy the third floor. Figure 3 shows the floor plan of the third and fourth floors. 3. The yellow cake storage bin and dryer dust collector sump are located on the second floor. 4. The ground floor houses the loading facilities consisting of two load out ports from the bin to barrels, a roller conveyor loop, drum weighing scale, and change room facilities. Figure 4 shows the ground floor plan. Figure 5 is an elevation view of this section showing the overall equipment arrangement.

Jan 1, 1981