Search Documents

The speed and internal accuracy of today's electronic calculators can be utilized to write an efficient slurry calculation program. The calculator's input/output printing feature offers additional benefits for data organizing and record keeping. This program allows slurry calculations to be performed without the urgency of immediately transferring a calculated result onto a process flowsheet or specification sheet. The number of flowsheets required for some hvdrometallurgical processes means the number of process stream blocks or ladder diagram entries can become substantial. Slurry calculations for such projects tend to become repetitious and tedious, and the chances for errors increase both in calculation and data entry onto process documents. Using this program has minimized both types of errors. Checking process flowsheets is particularly expedient with the program because you may "walk" through the flowsheet on a weight basis, i.e., solids rate and solids density, and have the program verify and/or correct the volume entries, gallons, and specific gravities. The program was initially used on a beneficiation project to check some 500 data entry values on ladder diagrams covering seven process flowsheets. Numerous hand calculation errors were determined and corrected, and the time for completely checking and correcting the flowsheet ladder diagrams was substantially reduced.

Jan 4, 1981

By E. Bakhtavar

All parameters influencing the decision for selection of a suitable extraction method were first selected as the base of this study. Then these parameters were categorized in two main groups. The first group of the parameters includes ?geomechanical and inherent characteristics of the dimension stones? such as hardness, RQD, compressive strength, joints plane orientation and spacing, and water content. The second group was named ?technical and economical parameters associated with the investor?s objectives? like for example extraction capacity (production rate), blocks recovery, mechanization, capital investment and operational costs. Finally, the influences of all mentioned parameters on the selection of the most applicable extraction methods have been assessed and discussed.

Jan 1, 2012

By M. E. Gershon

I would like to congratulate Professor Gershon on an idea that is obviously valuable and is certainly new to me. It has, however, to be further developed, in that one can get fallacious results by limiting oneself to positional weights. In the example problem, the positional weight of one block was 8.6 (the 8.0 value in the paper was incorrect) for 36 units in the cone, for a mean block value of 0.239. The positional weight of the second block was 4.4 for 15 units, for a mean block value of 0.293. Surely one would expect the second block to be rated higher. Additionally, the time value of money adjustment cannot be determined by depth, because the time that a block is mined is determined by the mining sequence, not depth. Figure 1 shows a slightly altered version of Professor Gershon’s pit. The overall value of the pit is the same, as are the total values under each of his blocks. The values in the right-hand cone have been reversed top to bottom, and the values in the rest of the pit adjusted to keep the central cone total unchanged. All values have been multiplied by 10. Figure 2 shows the sequence of mining, at three blocks per year, for Professor Gershon’s pit, and Fig. 3, the sequence for a pit under the other block. Table 1 shows the value and discounted value (157. ) of Professor Gershon’s pit, and Table 2 shows similar values for the second pit. It is apparent that the second pit schedule is more valuable than the first.

Jan 12, 1987

Talk some about your background. Mining, particularly coal, runs in the family. I come from a mining family, one generation re-moved. Both of my grandfathers worked in the coal mines. My mother?s father had worked as a coal miner in the South Hills area of Pittsburgh after coming to America from Croatia. My father?s father (who died of black lung long before I was born) had been born in America and worked as a mine foreman and superintendent in mines just outside the Pittsburgh area. My father often talked about when, as a child, he accompanied his father underground on Sundays to check the mine pumps. While I never expected to go into mining, I often read some of my grandfather?s books on mining technology that my father had kept. I started college at Penn State and drifted into mining engineering as my third declared major. I was finally realizing the importance of a career choice. I?ve never regretted that decision. One of my children, Mark, has followed me into mining engineering, much to my surprise and pride. Evidently, he had been listening to the many conversations I had with friends and colleagues in the industry and never considered any other career path. He has since married another mining engineer, Kray Davis Luxbacher, so we truly have a mining family and can talk mining when we get together. My other children are in more mundane lines of work and rapidly tire of the mining discussions. I?ve worked for operating companies: Pittsburgh Coal Co. (then a division of Consolidation Coal Co., and a company I believe both of my grandfathers had worked for), Island Creek Coal Co., and a research organization: Occidental Research Corp. I am now with Glenn Springs Holdings Inc., dealing with legacy issues (primarily environmental) related to Occidental?s previous mining operations (coal and minerals). As such, I have a broad view of the industry and the critical changes that are shaping our industry.

Jan 1, 2008

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process 1.2x0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm.

Jan 1, 2002

By Jafar Safarian, Leiv Kolbeinsen, Stian Seim, Hossein Salehi

The present work aims to investigate the link between the oxidation and reduction of a weathered ilmenite concentrate in terms of phase transitions, microstructural changes, and element distribution. An ilmenite concentrate sample was pelletized and fired at 1000 °C in air, and as a result, the pellets were oxidized. The oxidized pellets were reduced by hydrogen gas at 1000 °C, which yielded almost complete metallization of the iron content of the pellets. The ore and the pellets were characterized in each step by XRD and SEM techniques, and distribution of elements and phases were investigated. Ilmenite, pseudorutile, and rutile were the main phases detected in the ilmenite concentrate sample, and depending on the weathering degree of the particles, different fractions of the phases were identified in their microstructure. It was found that irregular rutile grains dispersed in a pseudobrookite matrix is the morphology of the oxidized ilmenite phase. However, increasing microcracks and porosities were the only microstructural changes in the pseudorutile phase after oxidation in air. Studying the specific types of the ore particles and their oxidized and reduced forms indicated that the phase distribution in the ilmenite ore particles dictates the phase distribution in the oxidized and reduced ones. Results show that the morphology of the reduced particles includes a titanium (III) oxide matrix in which reduced iron globules are dispersed.

Feb 8, 2021

By M. Karmis

The algorithms for the mathematical modeling to predict productivity of underground room-and-pillar mining systems are well known and documented. These algorithms consider the time-varying relationships between mining equipment for a given geometry of operations as well as other constraints. This paper presents WebConSim, a newly developed, Web-based, user-friendly computer simulation tool for the Windows environment. The simulator is easily customized for use by field engineers, planning engineers, and management and will help mine operators plan the optimum mining sequence for different mine geometries and equipment layouts. Program output includes production data and equipment utilization indices, as well as time driven event chains that can be used for virtual reality presentations.

Jan 1, 2001

By A. Karami

It is well established that an ordered sequencing of charge initiations in a blast pattern is an important design consideration that affects blasting performance. Delay times must be chosen such that damage to the rock mass is controlled. The accuracy of delay detonators is also of major concern. A large scatter could lead to an incorrect blast sequencing that would lead to damage to the rock mass causing increased over-break, degraded fragmentation, increased fly-rock and poor vibration control. In this study, the effect of using accurate delay detonators on the explosive energy generated is investigated. For this purpose, power spectral density of the blast vibration for delayed shots are calculated and compared with the case where holes are shot at the same time (no delay). At the end the results are presented and discussed.

Jan 1, 2000

By E. Bauer, S. Moore

Technological advances in underground coal mining have led to a reduction in fatalities. This study demonstrated that the percentage of cumulative injuries remained largely unchanged across two decades of technological advances (1983-1984: 37%; 2003-2004: 33%). Furthermore, it was demonstrated that the average number of lost days due to cumulative injuries has increased (36±55 days and 62±82 days, respectively) which may have been due to the increased age of the work force or an increase in length of employment meaning that the mine workers injured in 2003-2004 had been exposed to ergonomic risk factors longer than those in 1983-1984. It is recommended that ergonomics processes be implemented as a means to systematically identify, prioritize, and resolve the root causes of these cumulative injuries.

Jan 1, 2007

By E. Knell

COM Energy, Inc., a subsidiary of Occidental Petroleum Corporation, has constructed a 1.6 million hectoliter-per-year COM plant in Jacksonville, Florida. COM will be distributed to customers in the region as a substitute for fuel oil presently burned in boilers and kilns. As the market for COM grows, COM Energy, Inc. expects to build additional units both in this country and overseas. This paper addresses the overall status and technical aspects of the project, focusing on the facilities for COM production and utilization.

Jan 1, 1982

By S. Dixon

The Phelps Dodge - PD/PERI Heap2D Model is a phenomenological stockpile leaching model that has been used to investigate the best operating practices for leaching chalcocite. The model was used to investigate the interrelationships of raffinate application rate, aeration rate, raffinate iron grade, acid cures, lift height, crush size, bulk density, air injection spacing and raffinate drip emitter spacing.

Jan 1, 2006

By M. J. Gula, S. S. Xue, E. P. Horwitz

A study has been conducted to remove iron from sulfate solutions using Eichrom's Dipexo® extractant, P,P'-di(2ethylhexyl) methanediphosponic acid (H2DEH[MDP]). It is found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 106. Over 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 1999

By Anna Gustafson, Sohail Manzoor, Håkan Schunnesson

Sublevel caving operation relies on the estimation of ore grade at drawpoints, as the mine management uses grade to decide whether the material at a certain ring should be loaded or abandoned. Grade is estimated in various ways, including visual estimation, density-based calculation, and sampling and assay methods. The grade estimation at the world’s two largest underground iron ore mines owned by LKAB in northern Sweden is based on the density difference between ore and waste. The calculations assume a constant swell factor, a theoretical fill of 100%, and a linear relationship between bucket weight and material grade. This study evaluated these assumptions in detail based on the loading data for 12,237 buckets and concluded that the method has some shortcomings which render the assumptions invalid. Further research is required to deal with these shortcomings to improve estimation of the material grade.

Oct 17, 2022

By H. A. Kortmann

For the commercial production of iron ore pellets from hematite ores, as it is practiced in various pellet plants, the addition of lime has shown to be an efficient means with a view to improving cold compression and abrasive strength of the indurated pellets considerably. Unfortunately, it has also been shown at the same time, that the metallurgical properties as, for instance, swelling behavior, softening during reduction under load and disintegration of the grain, can be adversely affected to a high degree. In the course of smelting tests carried out by renowned steelworks, blast furnace operation was heavily disturbed by the swelling and early softening of the pellets, also by their disintegration in the low-temperature range, which altogether led to a considerable lowering of the smelting rate (1, 2, 3).

Jan 1, 1972

By M. Hamarat

Freeport-McMoRan Copper & Gold (FCX) is committed to preserving and enhancing biodiversity in the areas in which we operate. As a member of the ICMM, FCX is committed to implement the 10 Sustainable Development (SD) Principles throughout our business. FCX is also a member of the Wildlife Habitat Council (WHC), a nonprofit coalition dedicated to protecting and enhancing wildl ife habitat. In alignment with ICMM SD Principle 7 and our Environmental Policy, FCX has set a performance goal to prepare a biodiversity inventory in 2010 and land management plan by end of 2011 for all active mining sites. In 2010 FCX established a Biodiversity Task Force to assist sites in biodiversity management; optimize use of resources around the globe; implement FCX goals and targets; and align biodiversity programs with ICMM principles and guidance. The task force consists of Environment and SD Department management, scientists and engineers from FCX sites, and WHC staff. The Task Force recently issued a biodiversity inventory guidance document to set expectations and provide consistency across the sites when developing a biodiversity inventory and land management plan.

Jan 1, 2011

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By T. Geyer

The Carbon Disclosure Project (the pre-eminent global initiative for institutional investor collaboration on climate change) groups the business risks (and opportunities) related to climate change into four categories: 1. Regulatory risks from tightening legislation (and opportunities for companies that can make the carbon market work for them), e.g. rising costs for carbon and energy-intensive processes. 2. Competitive risks & opportunities generated by a possible decline in customer demand for carbon/energy intensive products (and opportunities from a consequent rise in demand for efficient / low carbon products). 3. Reputational risks from perceived inaction on climate change (and benefits to those perceived to be ?solutions providers?). 4. Physical risks from changes to climatic patterns, e.g. asset damage from extreme weather events; project delays; water scarcity; resource risks as certain crops become no longer viable in certain areas and new supply chains become necessary; and potential human and socio-political impacts. All of these are already having repercussions for businesses in certain sectors and geographies. The understanding of specific impacts of climate change is still evolving but it is clear that climate change will have a material impact on the value of many businesses, either directly or indirectly. Many commentators and analysts consider that rising energy costs are likely to represent the most direct and immediate investment risk that climate change and the resulting regulatory responses will create for business in the near term. However, it is already possible to identify numerous examples of competitive and reputational risks and opportunities that are leading to significant value creation or destruction in business: the success of the Toyota Prius; the rush by the UK?s leading supermarket retailers to ?green? their brands; and the surging fortunes of companies involved in the manufacture of renewable energy generation equipment, are all manifestations of this trend. In addition, the potential physical impacts of climate change are also making themselves felt in certain sectors: an example is the Australian wine industry, suffering after an extreme and prolonged period of drought. THE PROJECT This paper describes a project undertaken for a multinational mining company to examine the physical risks from climate change across its international business operations. The study addressed 163 components of the business and included operating sites (mines, smelters, and refineries), key transport routes (road and rail) and port links. The inclusion of the transport networks and ports is extremely important; key transport routes (e.g. a key railway link) may often be impacted (e.g. by flooding) far more than individual sites due to their large geographic exposure and multiple potential failure points. Extreme weather events causing loss of life and major economic damage continue to be front page news. According to the World Meteorological Organization, January to July 2007 ?was marked by record weather extremes in many regions across the world.? Inevitably, the associated phenomena are starting to impact business and investments, not so much as deal breakers, but in changing the parameters of risk management and the approaches required to devise mitigation measures. EXAMPLES OF EXTREME WEATHER EVENTS No one event can be presented as directly attributable evidence of climate change, however climate change projections suggest that the frequency and severity of many extreme weather events can be expected to increase in a warming world. In August 2003, a heat wave struck Europe, with temperatures as high as 42°C (108°F). As summer temperatures in much of northern Europe rarely exceed 30°C (86°F), the area was unprepared for the disaster, and many thousands of deaths occurred. In August 2005, Hurricane Katrina caused catastrophic damage along the Gulf Coast of the United States, forcing the effective abandonment of south-eastern Louisiana (including New Orleans) for up to two months and damaging oil wells that resulted in increased oil prices. Katrina killed over 1,800 people and caused at least $75 billion in damages, making it one of the costliest natural disasters of all time. This was followed in September, by Hurricane Rita which left 119 people dead along the U.S. Gulf Coast, causing $9.4 billion in damage. In January 2006, hundreds of people were killed when Russia, Eastern Europe and Scandinavia experienced the coldest weather for decades. In summer 2007, dramatic floods in the south central region of England, UK left 350,000 people without drinking water and many without electricity. Transport infrastructure was severely disrupted; combined with floods which occurred earlier in the summer in Yorkshire (North England), the damage is estimated to total over £2 billion. ASSESSING RISKS FROM CLIMATE CHANGE To date, only a minority of companies have attempted to quantify the risks from climate change. However, investors are seeking greater disclosure of climate change related risks and opportunities and it is expected companies that can demonstrate they are prepared for climate change will attract higher market valuations. Climate Change Threats A variety of climate change threats were examined for their potential to have a potential measurable impact on the mining company?s business operations. Those considered most significant were included in the study and are shown in Table 1 (see Appendix A). Certain threats can be considered as being cyclical in nature and the future predictions may suggest a change in the frequency and severity of such events (e.g. storms/hurricanes, rainfall, drought). However other threats are associated with a gradual change over time (e.g. loss of glaciers, loss of permafrost, sea level rises). A slightly different approach is needed to address this differing nature of the threats, as described subsequently. Climatic Regions Much of the research and data associated with climate change is collected and reported on a regional basis. An example of the climate change impacts predicted for a number of climatic regions is shown in Table 2 (see Appendix A).

Jan 1, 2009

By S. M. Pickering, L. T. Gregg

Appraisal of industrial minerals beneath privately owned land requires a different approach and mindset from valuation of base and precious metals or energy minerals, and from valuation of government-owned mineral lands. First, is it the value of inground minerals or of mining rights that is being sought? Second, value to whom, the mining company, a potential investor, the mineral landowner, a lending institution, the property tax assessor, or a condemnor? Third, how should mineral value be apportioned between the land and mineral owner, and a mining company with limited years of lease-hold interest? These and many other questions must be addressed before a valuation method and Discount Rate are selected. For various reasons the Income Method is most often used, with Net Present Value calculations made for long term predicted mining income. Choice of an appropriate Discount Rate is critical.

Jan 1, 2000

Resolution Copper Mining LLC (RCML) is currently in a Pre-feasibility study evaluating a large and deep copper and molybdenum deposit in the historic mining district east of Superior, Arizona. Work scheduled for the next several years includes dewatering the existing shut-down mine (the Magma Mine) and sinking an exploratory shaft to 2,130 meters (7,000 feet) below the surface. To dewater the Magma Mine and sink the exploratory shaft, RCML must extract and manage about 2 billion gallons of accumulated mine water inventory, as well as about 300 million gallons per year of new inflow. In order to conserve a valuable water resource in a desert environment, RCML worked with the New Magma Irrigation and Drainage District (NMIDD) to provide treated mine water to blend with and supplement the NMIDD?s water supply to approximately 2,000 hectares (5,000 acres) of farmland located east of Phoenix. A 44 km (27-mile) pipeline was needed to convey the treated water. It was essential that a treatment system be used which could reliably meet irrigation water quality goals, produce a non-scaling effluent to maintain pipeline flow capacity, and generate a dense sludge minimizing disposal cost and volume. This paper describes the resulting mine water treatment and recovery system (MWTS) and how the system has performed against objectives.

Jan 1, 2011

By John Reilly

The author?s paper at RETC 2007, ?Alternative Contracting Methods? addressed strengths and weaknesses of DBB+DB and introduced Construction Manager/General Contractor (Portland model) and Alliancing (Australian model). Considerable interest in these was expressed by several public agencies at that Conference and at the presentation. The author is assisting the Washington State Department of Transportation (WSDOT) and the Toronto Waterfront Revitalization Corporation (TWRC) with possible implementation of Alliancing. WSDOT is evaluating ways to do this and is considering a delivery methodology, under existing Legislation, based on the CMGC Portland model with incentives and disincentives, moving towards Alliancing. This paper will build on the 2007 paper and update implementation considerations.

Jan 1, 2008