Search Documents

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

What is your personal view and assessment of the overall health of the industry in the current global economy? The economic outlook remains soft for the near future and, although the global economy is showing signs of recovery, uncertainty has tempered the pace of recovery. In addition to uncertainty, we are still facing significant economic challenges in many parts of the world, including Europe and the United States. The rapid expansion of China?s economy has recently slowed, further contributing to the sense of uncertainty in the overall health of the global economy. This situation is both a blessing and a curse, depending on which sector of the mining industry we are considering. For example, coal, industrial minerals, aggregates, base metal and precious metals markets are impacted by different forces and drivers and will experience different outcomes within the same economic environment. Let me give a few concrete examples to illustrate this concept. The prevailing economic uncertainty that I have just described tends to drive investors toward safe havens. Gold has historically been viewed as a safe haven and as long as investors shy away from traditional investments, gold prices will remain high and gold mining companies will continue to expand and invest capital in their operations. The same sluggish economy that drives gold prices higher has the opposite effect on other segments of the minerals industry. A great example of this is industrial minerals and aggregates used in construction. The markets that consume these minerals have contracted significantly over the past five years. The outlook for this segment is poor, as the glut of available housing continues to inhibit demand for new construction and, thus, many industrial minerals. In addition to this, the federal government?s lack of political will to enact long-term legislation funding transportation and infrastructure projects continues to be a drag on the U.S. aggregates industry.

Jan 1, 2013

By W. E. Anderson

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at thirteen mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing buckets ranging from 30-to 220-cubic-yard capacity, were documented. We have judged that U.S. surface coal mining draglines, 30 yards and larger, can be represented as 120 machines having 60-cubic-yard buckets, moving 1.8 x 10 yards of overburden during 6,650 hours of productive availability per year. Based on our limited field study, we have calculated that downtime resulting from rope-related causes averages 105.6 hours per year for each (typical 60-yard) dragline. The total lost production from this source alone is thereby estimated at about 25 x 10 yards annually. Although study findings did not reveal anything about dragline rope life that wasn't known or practiced by one operator or another, most operators could expect improved rope life by periodic review of their practices and by adopting or adapting one or more life-improvement measures employed at other sites. Since rope productivity was found to vary by about five to one, among the sites studied, we believe considerably improved average performance is possible. As little as ten percent overall improvement would mean increased national productivity exceeding two million yards of solid overburden removal, and associated savings in rope costs alone of some two million dollars annually, not to mention any reduction of labor-related expenses. This report outlines preliminary findings which may prove useful to many operators in extending wire rope life, thereby lowering expenses and increasing surface coal mining productivity. Some of these modifications or adjustments in maintenance/operating practices would not require capital investment. We did not find anyone who had tried cost reductions by using presocketed dump

Jan 1, 1977

By Qiu Rongqing, Huang Kongxuan

This paper summarizes the results of treating arsenic­bearing refractory gold concentrates from six gold Mines of Chi­na by using bioleaching method and discusses the conditions of bioleaching processes. Results indicate that Thiobacillus fer­rooxidans T-3 Strain can intensely oxidize arsenopyrite, how­ever oxidation rate and degree differe considerably for different. During initial inoculation of 5 X 106 cell/ml. FeH contration generaly 4 -8 g/1. Sample size > 80 % - 3 20 mesh and pulp density 10 % ( w /v) and leaching time ,1 -- G clays, arsenic re­moval rate reached more than 80 % , Fe extraction ,10 - GO% desulfurization rate 30-45% after bacterial oxidation of 4-G days.

Jan 1, 1992

By William G. Pariseau

The flexure of geologic strata, a phenomenon of inter- est to geologists and mining engineers alike, is examined as a sheet bending problem' in Coulomb plasticity. Formulae for the distribution of stress, strain and displacement increments, volume change, change in the length of the central surface and power of dissipation, as well as for the neutral surface shift are given. Strains of any magnitude are considered. The analysis shows that deeply buried strata may bend and develop "tensile" cracks under generally compressive states of stress. It is also shown that bed separation and high capacity props are desirable in mechanized longwall mining, a result in keeping with operating experience. Although speculative at this time, the analysis provides a rational working hypothesis as regards the problem of strata flexure and control.

Jan 1, 1968

By F. Harold Weber

On July 13, 1967 the San Bernardino County Planning Commission approved publicly a request by American Smelting and Refining Company for a zone variance to conduct a silver mining and milling operation in the Calico district, southern California, Coincidentally, on July 14 the U.S. Treasury halted its sales of silver, and the U.S. free market price quoted rose immediately from $1.30 to $1.77 per ounce. In its request to the commission Asarco stated that about 13,500 to 15,000 tons of rock would be moved daily by surface mining, including 7,000 tons of ore. The ore would be crushed to minus three-quarters inches and the silver recovered "by a chemical process." The grade of the ore was not given, but the company said that it might also recover barite as a byproduct, The operation would employ 150-160 people. Additional activity in the district includes exploration programs by Superior Oil Company and Calico Silver Mines, Ltd. History and production: In retrospect, as the price of silver began to rise in 1961 from 91 cents an ounce, and as Asarco began its exploration program in late 1964, a new era for an old bonanza silver district would seem to have begun. The Calico district has been mined for silver only on a very, very small scale since 1882 to 1896, when an estimated $12 to $20 million (perhaps 15 to 20 million troy ounces) of that metal was produced from the 50-odd mines of the district and vicinity. These mines include the Silver King, Oriental, Waterloo, Garfield, Odessa and Waterman (which is about 8 miles west of the district). Much smaller-valued amounts of barite, gold, lead, and copper also have been produced from the ore deposits of the district; and from 1884 to 1907 the region yielded about $9 million worth of borate minerals.

Jan 1, 1967

By M. Sunkpal, K. C. Kocsis

"An underground environment with high air temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to a series of heat-related illnesses such as heat exhaustion, heat cramps and heat stroke. The majority of the metabolic energy of a mine worker results in the production of heat. If the human body is to maintain thermal equilibrium, then this metabolic heat must be transferred to the ambient surroundings at the same rate. The heat loss from the human body occurs through a combination of heat transfer processes, such as respiratory heat exchange, convection, radiation and evaporation. If the heat loss from the human body to the ambient surroundings is less than the metabolic heat produced, the excess will be accumulated within the human body, which will result in a rise in the core and skin temperatures. This can ultimately lead to a heat-related illness or a combination of heat-related illnesses. This paper aims to discuss major heat-related issues and provide an overview of various mine ventilation and cooling systems, which can be employed to overcome high levels of heat and humidity in underground mines. In this paper, the effects of heat exposure on the health, safety and productivity of the mine workers are also highlighted. IntroductionMining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injuries over the last century (Coleman and Kerkering, 2007; Saleh and Cummings 2011; Jacklitsch, Musolin and Kim, 2016). Occupational health hazards within the mining industry include hazards that are physical, such as traumatic injury or hearing loss; chemical, such as silica or diesel particulate matter; biological; ergonomic; and psychological (Donoghue, 2004; Saleh and Cummings, 2011). The effects of some of these hazards can be diagnosed immediately, while many, like black-lung and silicosis, will have long-term effects on the health, safety and life quality of mine workers (Donoghue, 2004; National Institute for Occupational Safety and Health, NIOSH, 2000). Among these hazards, exposure to heat and humidity can significantly affect the safety, health and productivity of mine workers, particularly in deep and hot underground mines (Roghanchi, Sunkpal and Kocsis, 2015). Short-term acute heat exposures can cause a rise in the core temperature of the human body, which can result in a heat-related illness or combination of heat-related illnesses. Adverse long-term chronic heat exposure can generate serious occupational heat-related illnesses, such as cardiovascular diseases, mental health problems and chronic kidney diseases. High core body temperatures coupled with dehydration can generate negative behavioral effects such as physical fatigue, irritability, lethargy, impaired judgment, loss of dexterity and loss of concentration (Xiang et al., 2014)"

Jan 9, 2017

By T. P. Meloy

Traditionally the mineral and mining engineers have characterized particles by sieving and-settling. Within the last decade, with the advent of the scanning microscope, entirely new experimental and theoretical approachesl-10/have been taken to minutely define the particle surface. This approach depends upon a hypothesis which takes advantage of the recent developments in automatic micro-scopes which can acquire large amounts of information in a short time and the new computational techniques which rapidly reduce the information to meaningful, practical data. Historically sieving and settling are the oldest sizing techniques known. Sieving by square screens, shown on Figure l-A is a common, current practice for sizing particles both in the laboratory and in production. A woven cloth is used which usually has square openings. The size particle that will pass through the opening dependent on a complex relationship of its morphology. As can be seen in Figure l-A, neither the width nor the height of the particle is determined by sieving. From square screens one and only one parameter characterizing the particle size is obtained, that parameter is the radius of the sphere that will just pass through the given sieve opening. A variation of square mesh screen is the slot screens, shown in Figure 1-B. Here another measure more closely associated with the height of the particle is obtained. Once again, one and only one parameter is associated with the particles' shape.

Jan 1, 1977

By G. Mike Bernard

The Andacollo gold mine is located near the town of Andacollo (population 14,000 people) in Chile’s region four. It is about 56km (35 miles) by paved road from the coastal city of La Serena. Santiago is about480 km (300 miles) south. Site elevation varies between 1,000 and 1,280 m(3,300 and 4,200 ft). The climate at the Andacollo site is moderate but arid. Average annual rainfall is only 130mm (5 in.). Because there is little rain and the temperature varies only a few degrees (14 to 24 C or 57 to 75F), there are no problems with freezing, solution dilution or pad saturation. The climatic conditions are ideal for heap leaching.

Jan 1, 1996

By David Hanson, Sean Warren, Chaparral Berry

"Coal bumps, also referred to as dynamic failure events or coal bursts (Lawson, Weakley, and Miller, 2016), continue to be a hazard in underground coal mines. While current design methods have significantly reduced the occurrence of coal bumps, they have not been completely eliminated. This paper investigates a correlation between coal compositional components, coal molecular structure, and probability of coal bumps in an effort to deepen understanding of coal behavior in an effort to reduce hazards in underground coal mines.Samples from the Penn State Office of Coal (PSOC) Department of Energy Coal Samples (DECS) were obtained for Fourier Transform Infrared Spectroscopy (FTIR) analysis using the KBr pellet method. Peaks indicative of the coal molecular structures were obtained using spectral integration software. These data, combined with published elemental data, were compared to historic bump occurrence in order to establish a possible correlation. Finally, results based on multivariate analysis of the elemental and FTIR data with bump status as the dependent variable suggest that elemental sulfur and molecular structure can be used as an indicator of bump susceptibility within the sample set considered.INTRODUCTIONThe study of coal requires consideration of multiple variables: percentages of organic and inorganic components, organic component origins, coal age, pore structure, cleat density, elemental composition, etc. Examining coal in situ increases the number of variables, such as coal depth, seam thickness, surrounding stratigraphy, and so forth. This collection of variables influences the subsequent behavior of coal simultaneously, and weighing their relative impact is a challenge for researchers. “A problem never exists in isolation; it is surrounded by other problems in space and time” (Ackoff, 1956). Having a substance such as coal that we know so much about, and yet so little, we have to ask what can be learned.An experimental study using Fourier Transform Infrared Spectroscopy (FTIR) was undertaken to determine if the chemical structure of coal contains information which may lead to a better understanding of triggers or attributes which may, in turn, lead to an increased probability of a dynamic failure event. While a full analysis of the factors driving dynamic failure are beyond the scope of this study, it is possible that a better understanding of the chemical structure of coal will lead to an increased knowledge of its inherent behavior, including its propensity to burst."

Jan 1, 2019

By T. Kawashima

The expanding volume of maritime coal transportation is intensifying the problems concerning large vessel service port construction, transshipment and environmental control. The major problem is the transshipment of coal. Customary methods for bulk transfer must be improved and/or new systems developed. Slurry unloading has a key role in the new systems. The present report reviews progress in slurry transportation research which has been done in Japan since the 1960s when large scale experiments for domestic transportation were done. Experiments on the effects of vibration on the slurry cargo and on reslurrying are discussed.

Jan 1, 1982

By I. Cameron-Clarke

This paper describes the design of a wellfield to provide a water supply for a new mine in southern Africa. A hydrogeological investigation was conducted that included the drilling and test pumping of eight wells located within a highly jointed pyroxenite aquifer. The wellfield was designed using a simple probabilistic analysis. This approach allowed the variability of the aquifer parameters to be taken into account. A risk assessment analysis was then carried out to evaluate the level of assurance that a reliable water supply could be provided by the wellfield. The analysis was also used to assess the effects of supplementing the water supply by pumping from nearby flooded workings.

Jan 1, 1992

By Zohreh Kazemi Motlagh, Virginia T. McLemore

Critical minerals are nonfuel minerals, essential to the U.S. economy and national security, whose supply chain may be disrupted. Mine wastes are potential sources of critical minerals. The goal of this project is to estimate and characterize critical minerals endowment in three mining districts in New Mexico: Black Hawk (Grant County), Hillsboro (Sierra County), and Magdalena (Socorro County), and assess their acid-generating potential. The Black Hawk district is an arsenide five-element vein deposit (Ag, Ni, Co, As, U, Bi, and local minerals like Pb, Cu, Zn, W, and Sn). The Copper Flat mine in Hillsboro district is a copper porphyry deposit. The Kelly mine in Magdalena was first mined at 1878 and are carbonate-hosted Pb-Zn deposits. Mine waste rock piles and tailings are sampled using USGS Beta sampling procedure. Geochemistry results show that Black Hawk district mine wastes samples are elevated in Ag (>200 ppm), Co (290 ppm), Ni (2,130 ppm), and Zn (8,463 ppm). Copper Flat mine tailing is elevated in Bi (111 ppm), Cu (7,453 ppm), and Zn (2,360 ppm). Downhole profile plots in Copper Flat show the positive correlation between Cu, S and Te values. Magdalena samples are elevated in Cu (5,700 ppm), Zn (129,500 ppm), and Pb (58,100 ppm). Determination of acid-generating potential in these areas suggests that Black Hawk district mine wastes are non-acid-forming while high S present in some Copper Flat and Magdalena samples can potentially cause acid mine drainage.

Feb 1, 2025

By Ted T. Biddle

The world energy crisis has created a greatly expanded exploration program for energy fuels. The demand for materials required for drilling operations such as barite, which is the primary component of drilling fluids, has increased proportionally. As in the case of many other minerals, existing high grade barite mines are no longer capable of producing the required tonnage. Consequently, exploration and development of lower grade ore bodies has been increased. The need to produce a high quality product at maximum recovery rates, along with the ever changing economics affecting both selling price and production costs has triggered accelerated research programs toward more sophisticated and efficient beneficiation methods. Taking into account the specific gravity differential between barite (4.5) and the normal gangue minerals such as silica and calcite (2.7), gravity concentration methods are the prime consideration with flotation as a scavenging process. Greater emphasis on particle size liberation, size reduction and concentration is also indicated. In order to accomplish these objectives, it has been necessary to revert back to the old adage, "Recover your minerals as soon as they are free."

Jan 1, 1980

By Donald J. Donahue

Ladies and Gentlemen: As we begin these three crowded days of technical and economic discussion of problems faced by mining and metallurgical engineers, it seems appropriate at this Keynote Session to consider the future of this industry from which we derive our livelihood, It is also appropriate at this international meeting to view our industry on a world-wide basis. First, let us assess the world's future needs for minerals - the needs which it is our industry's task to meet. Next, let us look at what supplies of minerals may be available to meet those needs. I will speak of this first in terms of the physical availabilities of minerals. Finally, we can consider some of the social or institutional factors which will condition the world's mining industry as it goes about its task of discovering, developing, producing, and delivering the minerals needed to meet the world's demands. Let me give you a foretaste of my conclusions. First, future world demands upon our industry will be enormous, eclipsing anything that we have known up to this point. Second, there is strong evidence that our earth's crust contains a sufficient physical quantity and variety of minerals to meet forthcoming needs for as long a period ahead as one can envisage.

Jan 1, 1974

By K. A. Natarajan, Abha Kumari

"The effect of applied DC potentials on the bioleaching of a chalcopyrite concentrate in the presence of Acidithiobacillus ferrooxidans is discussed. Copper dissolution was the highest at an applied potential of +600mV (SCE), while all the dissolved copper got cathodically deposited at a negative potential of -600mV (SCE). Electrobioleaching at an applied potential of +600mV (SCE) was established at different pulp densities as a function of time. The effect of applied potentials and electrolytic currents on the activity and growth of bacterial cells was assessed. Preadaptation of bacterial cells to the concentrate slurry and electrolytic growth conditions significantly enhanced copper dissolution. Electrochemical and biochemical mechanisms involved in electrobioleaching are illustrated with respect to oxidative dissolution and biocatalysis of anodic oxidation. IntroductionIn recent years, the bioleaching of low-grade chalcopyrite ores as well as their flotation concentrates has been receiving increased attention. Use of mesophilic bacteria such as Acidithiobacillus ferrooxidans in the bioleaching of chalcopyrite does not yield desirable copper extraction rates due to its easy passivation.Bioleaching of chalcopyrite using A. ferrooxidans has been reported to be very inefficient, and use of thermophilic bacteria at higher temperatures is recommended to improve its bioleaching rates. Bioleaching under imposed applied DC potentials or currents has been shown to enhance not only bioleaching kinetics but also to confer selectivity in mineral dissolution (Abhakumari, 1996; Chirpa Selvi and Natarajan, 1998; Natarajan, 1992a, b,c). Electrochemical principles governing electrobioleaching have been earlier illustrated (Jyothi et.al, 1989). The role of applied potentials on the activity and growth of A. ferrooxidans has also been studied (Natarajan, 1992b). Also, the electrochemical aspects of bioleaching of several sulfide minerals when present alone or in binary and ternary combinations have been reported (Jyothi et al., 1989). The electroleaching of copper-nickel concentrate (Natarajan et al., 1985) and electrobioleaching of sphalerite concentrates have already been studied (Selvi et al.,1998). However, it is possible to enhance the bioleaching rate of chalcopyrite in the presence of A. ferrooxidans under galvanic conditions in the presence of nobler minerals such as pyrite (Jyothi et al.,1989). Also, dissolution of chalcopyrite can be significantly enhanced under applied potential conditions. Ali Ahmadi and his coworkers recently studied the electrochemical bioleaching of chalcopyrite concentrates using moderate thermophiles (Ahmadi et al., 2010, 2011)."

Jan 1, 2015

By John A. Cherry

Groundwater monitoring conducted at an acidic uranium-tailings impoundment in Wyoming and at one in Ontario indicate that at these unlined impoundments situated on unconfined sand aquifers, there exist well-developed plumes of contaminated groundwater. In the literature similar results are reported for three other unconfined aquifers at mill sites in Wyoming. The plumes extend for distances of several hundred to a few thousand metres from the impoundments. They have a zone of low pH beneath and adjacent to the impoundments and a larger zone of near-neutral pH that extends to the outer limits of the plume. The low-pH zones are generally small compared to the neutral-pH zones because the advance rate of the fronts of acidic tailings-derived water is slower than the average velocity of groundwater which controls the advance of the high pH zone. The retardation of the acid fronts is a result of geochemical reactions that cause hydrogen-ion consumption in a slowly-advancing neutralization zone. Within each of the plumes, the low-pH zone has high concentrations of transition metals, heavy metals and radionuclides. In the neutral-pH zones all of the metals and radionuclides occur at significantly lower concentrations and are generally at levels much below those specified in national drinking water standards. An exception at two of the Wyoming sites is uranium, which exists at levels close to the drinking water limit. A second exception is ferrous iron at the Ontario site, which occurs at high concentrations throughout most of the plume. The carbonate alkalinity at this site is much lower than at the Wyoming sites. The field data indicate that even in very permeable aquifers with a low content of silt and clay, there is normally a considerable capacity for acid-front retardation. To take advantage of this capacity to control contaminant movement in the design, operation and decommissioning of tailings impoundments, it is necessary to be able to predict the rate of acid-front movement. This predictive task has two primary components. The first is to identify the important flow paths from the tailings through the groundwater system and the second is to determine the degree of acid-front retardation that will occur as the tailings-derived water moves along these flow paths. Relative to these two tasks determination of the effects of hydrodynamic dispersion is generally of lesser importance and simple approximations that do not involve field or laboratory tests are probably adequate. In order to effectively apply the acid neutralization concept to the prediction of subsurface contaminant migration at uranium-mill tailings, improved representations of hydrogeochemical behavior of iron and aluminum in the neutralization zone and of the consumption of hydrogen ions through reactions with carbonate and aluminum-silicate minerals are required. Along with the hydrogen ions contained in the tailings water the ferrous iron represents a large potential source of acid but the extent to which ferrous iron converts to ferric iron to produce acid is problematic. Detailed hydrogeochemical evaluation of existing contaminant plumes and the performance of laboratory experiments under appropriate redox conditions ore prerequisites for the improvement of predictive models. However, the existing field and laboratory data provide a basis for preliminary predictions of contaminant migration from acidic uranium tailings impoundments.

Jan 1, 1982

By J. Kretschmann, N. M. Smith, J. F. Brune, P. Goerke-Mallet

Coal production and coal use for electric power generation are diminishing worldwide. Germany will phase out lignite mining as well as lignite and hard coal-powered electricity generation by 2038. In the United States, coal production has dropped by more than 50% since 2006, including in key coal production states like West Virginia and Wyoming (EIA 2021). Closing mines and power plants across entire mining regions has significant socio-economic impacts. Existing industries must be focused on the post-mining economy by attracting new industries, and implementing job retraining programs for displaced workers, as former mining regions transition towards agricultural, industrial and recreational use. This paper examines the German “exit from coal” under the 17 UN Sustainability Goals and illustrates the complex procedures, interrelationships, risks, and rewards of the transition towards renewable energy sources, including wind, solar, hydrogen, and bioresources.

Mar 2, 2022

By T. Fernandez, V. Juchen, C. Petter, F. Cantini, V. Lenz, V. I. Araújo, R. Petter, R. Darrigo, A. Young, I. G. da Costa, J. Oppermann

There are many methods to estimate costs quickly. One of these is the Parametric Method, where costs are estimated from general algorithms (or curves). Derived from an original tool based on the O’Hara model, a software called MAFMINE was developed. MAFMINE is based on parametric models to estimate investment and operational costs in mining. The software itself is based on the use of a computer model known as client-server. However, the model needs new inputs from advances made by the mining industry, mainly in terms of electrification, automation, digital transformation and preconcentration to face Environmental, Social and Governance (ESG) concerns. Thus, this work was to prepare a new core module ready to incorporate the new technologies aiming to deliver operation and capital costs associated with environmental impact mitigation. The tool generates an order of magnitude estimate for CAPEX and OPEX to establish a very first Discounted Cash Flow (DCF) in a mining venture. For quick evaluations, at a preliminary level, the results are very promising.

Mar 2, 2022