Search Documents

By N. Sahin, M. Can, Z. Ekmekçi, Y. Öztürk, Ö. Biçak, I. B. Çelik, B. Kocabiyik

"In this paper, a case study from Çayeli Bakir Isletmeleri A.S. (Rize, Turkey) about the selective flotation of copper minerals from sphalerite is discussed. Çayeli Cu-Zn Sulfide Ore contains different ore types, such as yellow ore, clastic ore, bornite-clastic ore, bornite-yellow ore, and black ore. For some of these ore types, selective flotation of copper and zinc is very difficult presumably due to presence of secondary copper minerals such as bornite, chalcocite and covellite, and also surface oxidation. These factors affect Cu-Zn selectivity due to activation of sphalerite particles in the ore during the process. The main objective of this work was to improve Cu-Zn selectivity by optimization of the pulp chemistry for different ore types of Çayeli ore. After preliminary flotation tests investigating effects of different chemical conditions, a plant survey was performed to determine the plant performance and sources of the problems when problematic bornite-clastic ore is treated in the plant. Various chemical conditions are tested in the laboratory scale test for better depression of sphalerite in copper flotation circuit. Combination of Na2S+ZnSO4+MBS was found to be the most effective depressant scheme. INTRODUCTION Ore variability is one of the most important factors affecting performance of a process plant both in short and long term planning. The geometallurgical modelling becomes a common tool to determine ore variability problems and develop the most efficient solution during life of mine (1, 2). Flowsheet design and equipment selection and sizing are usually done based on the results of ore variability test works. However, in some cases ore variability may not be foreseen during the design stage and therefore the solutions should be developed based on the existing flowsheet and equipment in the plant. In this situation, ore characterisation, problem statement and diagnostic testing should be applied step by step. The problem could be due to changing feed grade, mineralogical characteristics, grindability and surface characteristics when flotation is involved. The variability in feed grade with fixed mineralogy can be handled with relatively simple modifications (i.e. adjusting throughput or equipment capacity) in the plant. Variability in ore mineralogy is the most complex and difficult problem to tackle. Because, mineralogical variations could bring variations in mineral composition, texture and liberation. These variations can potentially lead to the variations in grindability of the ore and flotation behaviour. Variations in grindability are usually managed by optimization of operational parameters in grinding circuit, as it would be costly to replace the existing equipment in the circuit (3). The variations in flotation behaviour are mainly due to variations in mineral types and distribution, texture and surface oxidation. One or all of these factors could be observed in a flotation operation. Therefore, a comprehensive investigation both in plant and lab scale should be conducted for definition of source of the problem. The testwork to solve the problem and retrieve the performance is planned and conducted depending on the source of the problem (4, 5)."

Jan 1, 2017

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By Jon A. Hummer, MICHAEL R. SHAHAN, Aleksandar D. Bugarski, Shawn Vanderslice

A study was conducted in an undergroundminewith the objective to identify, characterize, and source apportion airborne aerosols at the setup face and recovery room during longwall move operations. The focus was on contributions of diesel- and battery-powered heavy-duty vehicles used to transfer equipment between the depleted and new longwall panels and diesel-powered light-duty vehicles used to transport personnel and materials to various locations within the mine. Aerosols at the setup face were found to be distributed among diesel combustion-generated submicrometer and mechanically generated coarse aerosols. According to the data, the submicrometer aerosols downstream of the setup face were sourced to diesel exhaust emitted by vehicles operated inside and outside of the panel. Depending on the intensity of the activities on the panel, the outby sources contributed between 12.5 and 99.6% to the average elemental carbon mass flow at the setup face and recovery room. Extensively used light-duty vehicles contributedmeasurably to the elemental carbon concentrations at the setup face. The number concentrations of aerosols downstream of the setup face were associated with aerosols generated by combustion in diesel engines operated in the shield haulage loop and/or outside of the longwall panels. Entrainment of road dust by diesel or battery-powered load-haul-dump vehicles operated near the measurement site appears to be the primary source of mass concentrations of aerosols. The findings of this study should help the underground mining industry in its efforts to reduce exposures of miners to diesel and coarse aerosols.

Apr 14, 2020

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020

By M. S. Moats, W. C. Hartzell

The stable domestic supply of gallium, indium, and germanium has been identified as a critical need for the United States. Electric arc furnace dusts, processed to recover zinc, produce a residue that could be a potential source of these critical materials. An industrial zinc leach residue was characterized to determine its particle size, chemical composition, and predominant mineral phases. Heated, atmospheric, agitated leaching using sulfuric acid and hydrochloric acid was examined to determine the extractions of gallium, indium, and germanium as a function of concentration and temperature. Extractions of gallium were found to be similar to iron in all experiments. The maximum percentage of Ga, Ge, and In leached into solution were 71%, 63%, and 48%, respectively.

Feb 1, 2023

At long last, mining is on the rebound in Minnesota?s Iron Range and the excitement is starting to show. The SME Minnesota Section?s annual meeting was once again held in the heart of Iron Range country, at the Duluth Entertainment and Conference Center on the Duluth waterfront. The conference boasted a record attendance of 475 people and its largest-ever trade show. Appearances by Governor Mark Dayton?s new Iron Range Resources & Rehabilitation Board (IRRRB) appointee, Tony Sertich, as well as a local Fox news crew (see clip on SME website [link: http://fox21online.com/news/duluth-mining-conference-breeds-optimism-tech-innovation]) made clear that a lot of eyes [ ] are on the industry as it dusts itself off from the 2008-2009 recession. While the early years of the 21st century were very good to the Iron Range, the global drop in commodities prices and production left many companies reeling and brought back bad memories of the collapse of the industry in the 1980s. However, two years of solid growth and a rebound to above pre-2008 production levels have let the Minnesota mining industry to relax a little and talk seriously about long-term growth and stability.

Jan 1, 2011

By Nikhil Dhawan, Shrey Agrawal

India’s most extensive renewable energy expansion program targets 280 GW of solar energy by 2030. Due to the massive generation of photovoltaic waste (expected 34,600 T by 2030), stringent recycling effort to recover metal resources from endof- life PVs is required for resource recovery, circular economy, and subsequent reduction in the environmental impact. The present study investigates the recycling potential of end-of-life silicon solar modules. The feed characterization reveals that most of the values in PV modules are concentrated in the frame (pure Al), Si wafer (72–84% Si, 9–12% Al, and 0.13–0.71% Ag), and electrical connections (Cu wire coated with Sn). The Si and Ag values in the feed were beneficiated using water fluidization, and concentrate with 90% Si and 2% Ag was attained in the underflow concentrate. Ag values were recovered in the form of AgCl by leaching in nitric acid and precipitation. After the purification step, the residue containing 99% Si can be further utilized to fabricate Si wafer and Al-Si alloy. The preliminary cost estimations suggest that the proposed process is economically viable for the recycling of solar panels with the maximum value generated from the AgCl precipitate followed by Al panels and Si wafers.

Nov 14, 2022

By K. V. Raj, T. Bhowmick

"Control of fugitive dust in high latitude open-pit mines is challenging due to unique atmospheric phenomenon resulting in complicated flow regimes, and atmospheric inversion due to lack of adequate solar insolation during prolonged winter seasons. In this study, two idealized (One conical and one trapezoidal) three-dimensional open-pit mine geometries are simulated for differing seasonal conditions using the CRADLE-CFD package. The airflow is modeled using Standard Kappa-Epsilon Turbulence Model solved by RANS equations. The concept of particle tracking is used to predict the flow pattern of dust particles. For various climatic conditions, and two different pit geometries, fugitive dust particles varying in size (PM0.1 to PM10) and concentration are generated at various locations of a mine and dispersed by the airflow pattern inside the open-pit mine. The amount and location of dust particles inside the pit is reported at various time intervals. The development of atmospheric inversion during the winter season significantly affected the amount of dust retention inside the open-pit domain. While during the summer, airborne dust particles were transported outside the open-pit domain in a short time. INTRODUCTIONComputational fluid dynamics (CFD) modeling of open-pit mines is challenging. In a recent paper, Bhowmick et. al. [1] presented different constraints and challenges in developing a 3-Dimensional CFD model. In order to obtain realistic results from a simulation, however, appropriate values of various inputs are required. Simulation results of a 3D non-hydrostatic model by Shi et al. [2] showed that both the mechanical and thermal forcing are important mechanisms, controlling the development of the atmosphere inside an open-pit. Alvarez et al [3] used a CFD model for predicting dust dispersions in a medium sized limestone quarry, and presented several iso-surfaces of varying dust concentrations using ANSYS CFX. A similar study by Torno et al [4] introduced a more sophisticated parameterization of the dust sources. Flores et al. [5] used an OpenFOAM CFD simulation package to simulate and predict pollutant dispersion in an idealized and an actual open-pit mine in Chile with an intense insolation condition. The model was simulated for three different conditions: (i) air advection (10 m/s) driven mechanical turbulence; (ii) surface heat flux (240 W/m2) driven thermal buoyancy; and (iii) both air advection and surface heat flux driven conditions. The results of the simulations showed that the buoyant currents contribute to the removal of a large percentage of the dust particles. The buoyant currents modify the purely mechanical-turbulence induced flow pattern and reduce the particle residence time, commonly observed in a purely mechanical turbulent flow (non-buoyant case)"

Jan 1, 2015

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024

By MUSTAFA ERKAYAOGLU, Muhammet Mustafa Kahraman

Particulate matter (PM) is one of the main actors related to air pollution caused by surface mining. Fugitive dust, considered as particulate matter that cannot be collected by conventional measures, is classified by the particle size. The Environmental Protection Agency (EPA) categorizes PM as coarse and fine particles based on the particle size being less than 10 μm (PM10) and less than 2.5 μm (PM2.5). Basic operations of surface mining such as drilling and blasting, loading, haulage, and processing are processes that can potentially generate fugitive dust. Regulations and legislations enforce the mining industry to use environmental monitoring systems, fugitive dust level measured by PM10 level as part of this. Air quality monitors are positioned at different locations around surface coal mines and track air quality levels during production. This study introduces a data-driven methodology to handle air quality issues related to fugitive dust at surface coal mines. Data is sourced from different mine equipment in real-time and they are integrated with air quality monitoring systems to provide information to support decisions for fugitive dust. The method is implemented and demonstrated in a case study at a large surface coal mine.

Sep 29, 2020

By Johan K. Rodenburg

A major bauxite belt was discovered and evaluated from 1969 to 1974 by P. T. Alcoa Minerals of Indonesia in West Kalimantan, Indonesia. The proven reserves of beneficiated bauxite are 800 million tons averaging 38.6% AA1203 and 3.0% RSiO2. Inferred reserves of washed bauxite are in excess of 2 billion tons. The bauxite occurs as capping of low lying hills which were formed during the post Paleogene peneplaination stage. The overburden varies from 0.6 to 3.8 meters and the nodular bauxite horizon from 2.2 to 5.2 meters. The deposits were formed by the in situ weathering of predominantly acidic and basic intrusive rocks.

Jan 1, 1984

By Manoj Khandelwal, Minghui Liu, Jian Zhou, Kun Du

The waste rock and tailings backfill into the mined-out areas are the most effective method for solving the environmental pollution and surface disasters for nonferrous metals mines. In practice, the success and availability of backfill operations are dependent on the slurry fluidity and the strength properties of cement backfill. The transport of the slurry through the pipeline to the designated backfilling area relies on its eximious flow properties, while the appropriate strength of the filling body ensures the safe operation of the stope. In this paper, the effects of cement and aggregate types on the slurry fluidity and strength characteristics of cemented backfill are studied in detail, which are often ignored in other pieces of literature. Diffusivity is used as an indicator to evaluate the slurry fluidity. Various slurries whose concentrations ranging from 70%, 73%, 75%, 78%, and 80% are made with different aggregate ratios and cement-sand ratios are tested. It has been shown that slurry fluidity is inversely related to its concentration, but 78% is the “stopping point” for the deterioration of fluidity. The addition of rod-milled sand improves or worsens the cemented backfill (CB) strength depending on the amount of rob-milled sand. The uniaxial compression experiment results on 216 CB specimens produced by different combinations of influencing variables showed that CB specimens made from cement with superior mechanical properties have a higher uniaxial compressive strength (σucs). It has been also found that the effect of aggregate ratio on the CB strength is not singular, but works in conjunction with the curing time and the cement-sand ratio. The longer the curing time and the higher the cement content, the higher the CB’s σucs. To avoid the time-consuming and costly problem of obtaining the strength of the CB from indoor experiments, an SVR model capable of predicting the uniaxial compression strength of CB specimens is proposed, which is optimized by genetic algorithm (GA) and particle swarm optimization (PSO) algorithm. The results of the three performance indexes (MAPE, MSE, and R2) show the superior performance of the GA-SVR and PSO-SVR models and the agreement of the predicted results with the experimental results, which indicate that these two models can accurately predict the σucs of CB.

Feb 3, 2022

By Randy Reed, Barbara J. Arnold

Respirable crystalline silica poses a significant health risk, with the American Lung Association estimating that 2.3 million workers are exposed to silica in the workplace. This includes mine workers as well as those in many other industries. Reducing dust formation is sometimes not possible so other methods to reduce exposure are critical. These methods include the use of surfactants to reduce airborne dust particles. However, it is the proper selection and application of surfactants that leads to reduced dust exposure. A discussion of how surfactants work, especially for silica dust, leads to guidance for surfactant selection followed by a review of technologies for their application.

Feb 1, 2024

By E. D. Gálvez, L. A. Cisternas, R. Acosta-Flores, F. A. Lucay

Froth flotation processes are carried out in flotation cells that are grouped into banks, and these banks are interconnected, forming a flotation circuit. A literature review shows the existence of papers related to flotation circuit design based on mathematical programming. However, due to the complexity of solving the mathematical model in most of the work, it is considered that a small number of species is present in the feed to the circuit, which differs from practice. In addition, simple bank models are generally used. This paper presents a methodology for designing mineral concentration circuits that overcomes the problems mentioned. It allows the use of more suitable cell or bank models and the inclusion of several species. The methodology is based on two phases. The first phase identifies the set of optimal structures using discrete values of stage recoveries, solving several mixed integer linear programming (MILP) problems. In the second phase, the optimal design for each of the structures obtained in the previous phase is determined using a suitable model for the recovery at each cell or bank, which results in a mixed integer nonlinear programming (MINLP) model. The design of a copper concentration plant with eight species and the design of a zinc concentration plant with three species and five size fractions by species are used to validate the proposed methodology. The structure of the cells in the rougher and cleaner banks deliver structures that are novel.

By H. Sevim

Three transportation systems in surface coal mines: 1-Truck Haulage, 2-Belt Conveying, and 3-Coarse-Coal Slurry Transportation are compared from the operations and cost point of Views. Computerized design and cost models were developed and cost data banks were compiled for each system. These models can be used to evaluate transportation systems and layouts that are practiced in most of the U.S. surface coal mines. A typical midwestern area strip mine was considered for illustration purposes. Sensitivity analysis on critical parameters such as production rate, transportation, distance, etc. was conducted and the outcomes are presented.

Jan 1, 1990

By YUSONG MIAO, DI WU, XIANRONG YAN, YIPING ZHANG, JIE LIN, KEBIN LI

Rock fragmentation size distribution is often used as an important index to account for the blasting effect because it directly affects the subsequent loading, transportation, and secondary crushing. Due to the mismatching of explosive and rock wave impedance, high boulder yield often occurs which affects the blasting effect. In this study, methods of measuring rock acoustic impedance, rock strength point loading, and detonation wave velocity have been used to obtain more accurate input parameters. Then, in the watershed image segmentation technique, the Gates-Gaudin-Schuhmann and Rosin-Rammler distribution functions have been used to analyze and quantitatively describe the rock fragmentation size distribution in the existing muck-pile. Finally, taking the rock properties, explosive performance, blasting parameters, and system characteristic variable into consideration, support vector machine (SVM) regression model has been analyzed on the learning and prediction of samples. The results show that SVM has a good prediction accuracy, high precision, and strong generalization ability. The optimized matching coefficient of rock and explosive wave impedance K ranges from 2.50 to 2.58 times. This study has developed a series of simple, accurate methods for rock properties analysis, detonation wave velocity measurement, and muck-pile model image processing, and a basis for predicting and evaluating rock fragmentation size distribution and optimizing the matching coefficient before carrying out a blasting operation.

Jan 22, 2021

By R. Benito

This paper describes the development of a life-of-mine schedule (LOM) for one of the world's largest known sedimentary copper-cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity-constrained process facility. This paper discusses the LOM scheduling objectives and constraints, data preprocessing steps such as ore binning, block aggregation and clustering analysis as a scheduling aid, the mine scheduling approach and results and conclusions. Mining Engineering, 2011, Vol. 63, No. 8, pp. 39-47. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Jeffrey L. Zelms

There is no known, practical substitute for lead in the automobiles, communications systems, medical equipment and computers that Americans use every day. However, there are many who say lead should be stopped at its source -- banned. As America's largest lead producer, The Doe Run Company has ralized that it must do more than mine and reclaim lead efficiently and safely. It must also earn the public's consent to operate if it is to continue to be a viable business. LEAD - THE BRILLIANT PERFORMER: REFURBISHING AN IMAGE It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. I haven’t perused the course catalog for Penn State’s College of Earth and Minerals Sciences. But I strongly suspect I wouldn’t find such a course there today, either. A statement by the chairman of one of the country’s largest chemical companies leads to the point I want to make. He described his business this way. He said, “We’re a public affairs company that just happens to produce and market chemicals.” Like chemicals, minerals and mining are politicized today. To the extent that we don’t understand that reality, we don’t understand that reality – and act on it – we’re less likely to survive in this business. Some of you may well be saying to yourselves, “This guy Zelms is an alarmist.” That’s fair enough. Because it is absolutely true that there’s n o known, practical substitute for lead today. And it’s also absolutely true that, knowingly or not, Americans use lead everyday. It’s in our automobile batteries. It’s an integral part of communications systems. High tech (and low tech) medical equipment contains lead. And lead is an essential component of computer and TV screens. But even with all these uses, lead has a negative image today. An image so negative that its very existence is threatened. If you doubt that, consider these two statements made in 1989. Statement one. “It is probably reasonable to argue that exposure is the single most important and critical environmental health problem in the U.S., and possibly also the world…” Statement number two. “Many of the uses of lead should be terminated. We need to go back to the ultimate source: that is, taking lead out of the ground and putting it into the product stream and we need to turn it off at the ultimate source. Not the approximate lead in gasoline, or lead in air, or lead in food. Go right back to the source and start cranking it down." (End quote.) Those are what I call strong statements. And they weren’t made by some celebrity spokesperson for the environment like Meryl Streep. Both these statements were made by Dr. Ellen Silbergeld, whose long list of professional and academic credentials includes: o Adjunct professor and research scientist at the University of Maryland Medical School and Johns Hopkins: o Chief toxic scientist and director of the Toxic Chemicals Program of the Environmental Defense fund; o and President of the Society for Occupational and Environmental Health. If Dr. Silbergeld were the only person making these kinds of statements, it would be one thing. But she’s not a voice in the wilderness, by any means. Also for those of you who say, well since there’s no known substitute for lead, how on earth could it be banned. I refer you to a number of bills before Congress that would permit the EPA to ban any product if it is determined that its

Jan 1, 1992