Search Documents

By R. E. Le Messurier

GENERAL DESCRIPTION The mines are located at Broken Hill in the western part of New South Wales, Australia, 930 km west¬northwest of Sydney. Mining Methods Where pillars must be left between stopes, extraction of a block of ore between two or more levels is carried out in stages: 1) Stopes are mined overhand by horizontal cut¬and-fill stoping, or by long-hole stoping. The various methods of horizontal cut-and-fill stoping used are desig¬nated as: -Loader cut-and-fill stoping with horizontal blast¬holes and diesel load-haul-dump (LHD) units. -Open stoping with horizontal blastholes and com¬pressed air or electric scrapers, or with diesel or electric LHD units. Square-set timber stoping, where ground condition precludes open stoping. The backs are sup¬ported with timber square sets. Pattern rockbolting of the backs may be used as an intermediate stage between open stoping and square-set stoping. 2) Vertical pillars are mined by undercut-and-fill stoping or by vertical crater retreat stoping. 3) Where a horizontal pillar has been formed below the level above the primary stope, this level pillar, usually 6.1 to 8.2 m in depth, may be mined by over¬hand square-set stoping or by undercut-and-fill. Long-hole stoping is used at the Zinc Corp. (ZC) and New Broken Hill Consolidated (NBHC) to mine parts of the zinc-rich A and B lodes. Drilling is carried out from drill drives and, in some cases, sills. Hole sizes used are 165 mm (61/2 in.), 110 mm (4'h in.), and 65 mm (21/2 in.) nominal diam with hole lengths being limited to 50, 30, and 20 m respectively. Ammonium nitrate-fuel oil (ANFO) and water gel explosives are used. Broken ore is loaded from drawpoints at the bottom of the stope using rubber-tired diesel-driven LHD units which deliver ore to an orepass. Annual production at Zinc Corp. and NBHC accord¬ing to mining method is given in Table 1. At Zinc Corp. mining is being carried out at depths varying between 200 and 832 m. At NBHC it ranges from 528 to 915 m below the surface. The average travel time to the stope is 30 to 45 min. GENERAL ORE BODY REQUIREMENTS Size, Shape, and Dip There are six separate lodes which carry minable ore in the mines of Zinc Corp. and New Broken Hill Consolidated. The lowest of these and the main ore bodies presently being mined at Zinc Corp. are the lead lodes, consisting of a siliceous fluoritic ore body (No. 3 lens) and overlying it a calcite rhodonitic ore body (No. 2 lens). Each possesses characteristic ratios of lead, silver, and zinc, although the grade within each lens is variable, in places being as high as 30% Pb. There are also low¬grade portions which consist chiefly of poorly mineral¬ized rhodonitic material. No. 3 lens terminates within the Zinc Corp. leases, while No. 2 lens continues into the NBHC leases where it continues to provide a significant proportion of pro¬duction from the mine. Overlying the No. 2 lens are the various zinc-rich ore bodies. In ascending sequence these are lower No. 1 lens, upper No. 1 lens, A lode, and B lode. A typical assay for the small No. 1 lens group ore bodies is 8% lead, 50 g/t silver, and 20% zinc. The `A' lode is a large low-grade ore body in which the higher grade sections assay 4% lead, 30 g/t silver, and 10% zinc; larger quantities of lower grade ma¬terial also occur. B lode, the main zinc lode, typically assays 5% lead, 30 g/t silver, and 17% zinc. B lode increases in size as it extends south, and in NBHC is a major ore body, contributing about 52% of the production. All the lodes pitch south, the average pitch being 0.52 rad (30°) in the Zinc Corp. leases and rather flatter than this in the NBHC leases (see Figs. 1-3). The ground is all competent rock. Production requirements at Zinc Corp. are 900 000 t and 1 200 000 at NBHC.

Jan 1, 1982

By Frederick W. DeVries

The following charts were presented at the Randol Gold & Silver Forum 2000, held at the Hotel Vancouver (Vancouver, B.C.) from April 18-21, 2000. It must be borne in mind that the "facts" stated and con­clusions drawn by the author were not as the result of a rig­orous technical investigation, but rather as a member of a journalistic team seeking a rapid view for presentation as news to a TV audience. Since the author's visit, some retrenchment on the part of the operators on estimating the cyanide content of the spill seems to have occurred. This does NOT alter the conclusions that (a) the spill was an intolerable embarrassment for the world mining industry, nor (b) the potential damage to future mining investments, should prompt action not be taken: 1. to understand the reasons for the dam failure, and 2. to draw up firm concepts of how to avoid future fail­ures of dams at mining properties containing materials that are toxic, environmentally unfriendly, or with as highly dis­comfiting a profile as cyanide.

Jan 1, 2000

By J. F. Abel, R. J. Spengler

Convergence measurement across the 17.4-m (57-ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 x 9.6 m (38 x 31.5 ft) inside diameter. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2.75 in.), and 5.7 cm (2.25 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1987

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2018

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2017

By Wen Lan Chen

In the plant where the 800m diameter cyclone was tested, 500 STPH of 50m x 0 raw coal was pulped in a heavy medium tank and pumped originally to four 700mm heavy medium cyclones. For the test one of these units was replaced by an 800mm diameter cyclone with the subsequent feed pressure for both units sets at approximately 15.0 psi. Since this was a feed to zero plant, an appropriate bleed of heavy medium to the dilute medium circuit was established to en- sure that the cleaning of the 500m x 0.5mm raw coal would not be adversely affected by high levels of 0.5mm x 0 fine coal present in the heavy medium. The medium gravity measured varied between 1.41 and 1.43. During a three-hour test on June 10, 1983, the raw coal sample was collected from the feed belt while the clean coal and refuse samples were collected separately at proper locations along the product streams of the two different diameter cyclones. All of these samples were shipped to the laboratory for screen and sink- float analyses. The raw coal screen and ash analyses are shown in Table 1.

Jan 1, 1984

By Paul Soros

There has been a steady increase in shiploading capacities in the last 20 years. One of the reasons has been the general increase in ship sizes, with the largest vessels currently around 280,000 DWT in the bulk trades. Obviously, the large vessels can accept loads faster and their economic utilization justifies higher loading rates, up to a point. The high capacity facilities have loading rates far beyond this point. The economic logic of these facilities is based on the fact that for a given annual throughput the capital and operating cost of a single high capacity system is less than that of two smaller systems. Thus, where the projected throughputs are large, there is a great incentive to reduce capital costs by maximizing capacity. Tubarao, in Brazil, designed for a 100 million ton per year throughput with one finger pier and one high capacity berth is a successful demonstration of this approach. In the current state of the art, the high capacity systems have shiploading capacities in the range of 10,000 - 16,000 TPH, for annual throughputs of 20 million tons and larger per loading berth.

Jan 1, 1982

By J. F. Burr, D. Snyder, W. Calder

"INTRODUCTION “Explosion protection” refers to techniques used to minimize the potential for electrical and electronic equipment to create an ignition while operating in a hazardous location (HAZLOC). In particular, U.S. coal mines are required to use equipment in certain areas of the mine that has been approved by the Mine Safety and Health Administration (MSHA) for use in a methane and coal dust environment to limit the risk of the equipment creating an ignition-capable spark or a thermal energy ignition. In general, MSHA’s regulations for explosion protection recognize two techniques: the use of explosion-proof enclosures (XP boxes) and 2-fault intrinsic safety for electrical and electronic equipment. For 2-fault intrinsically safe (IS) equipment, the U.S. mining industry requirements are unique in that the equipment is certified by MSHA. The criteria MSHA uses to evaluate equipment for intrinsic safety, as required by Title 30 of the Code of Federal Regulations (30 CFR) [30 CFR, Sections18.20(b), 18.68(a)(1), 19.1(b), 20.1(c)(2), 22.6, 23.6, and 27.20(a)], is published in a document referred to as ACRI2001 (1). Outside of U.S. underground mining, many industries and countries accept equipment that is designed to a consensus-based international standard (ANSI/ISA 60079-11 is the U.S. version). The purpose of this study is to provide an overall assessment of the ANSI/ISA 60079-11 standard on 2-fault intrinsic safety and the MSHA ACRI2001 acceptance criteria, and determine if the ANSI/ISA document can be an alternative to ACRI2001 while maintaining an equivalent or better level of safety for miners. There are many drivers for this study. First, immediately after the 2006 MINER Act (2) was passed, there was a perception in the industry that the unique MSHA requirements were contributing to delays or restricting the availability of equipment to meet the requirements of the Act. Additionally, the MINER Act required that mine operators submit an accident response plan for MSHA approval, to be reviewed every six months. MSHA is required to determine if these plans reflect the most recent credible scientific research and make use of currently commercially available technology. There is a concern, as expressed in a recent National Academy of Science (NAS) study (3), that the unique requirements for U.S. mining may be limiting the technologies available to coal miners and technology options for mine operators. Accordingly, the study recommended that the National Institute for Occupational Safety and Health (NIOSH) and MSHA re-examine their technology approval and certification processes to ensure they are not deterring innovation, and explore opportunities to cooperate with other international approval organizations to harmonize U.S. and international standards without compromising safety. Lastly, the National Technology Transfer Act (NTTA) and the accompanying Office of Management and Budget’s OMB-119 circular mandate the use of consensus-based standards by federal agencies. However, for U.S. mining operations, MSHA cannot accept such standards unless a determination is made that such standards provide an equivalent level of protection for the miner, per the requirements of the 1977 Mine Act, the 2006 MINER Act, and 30 CFR Part 18 regulations."

Jan 1, 2017

By L. Alagha, O. Molatlhegi, S. Khatibi

"In the present study, the effect of organic/inorganic (hybrid) polyacrylamide polymer on fine coal flotation was investigated. Raw coal samples contain about 37% of ash-forming mineral at a feed size of -75 + 38 um were subjected to flotation tests in the presence of in-house synthesized hybrid Al(OH)3-PAM at different polymer dosages and pH values. Results show a significant improvement in both combustible recovery and ash rejection at 1 ppm polymer dosage. Further improvement of combustible recovery was obtained when flotation was performed at pH 5. Interfacial properties of coal particles before and after flotation were examined through electrokinetic (zeta potential) measurements of coal/water slurries. Zeta potential vs. pH curve were established and compared. In the case of raw coal/water slurry, zeta potential-pH curve resembles the ash-forming minerals (silica and clays) more than coal. After Al(OH)3-PAM-assisted flotation, the zeta potential of froth/water slurry shifted to more positive values point which strongly indicates significant removal of ash-forming minerals from coal by Al(OH)3-PAM. INTRODUCTION Coal has been a major commodity in meeting the world energy demand during the past several decades (Milici et al., 2013). According to the international energy agency, global coal demand will continue to increase for the coming decades. With increasing world population, the global electricity demand would also increase as more people would get access to basic electricity especially in developing countries (Maggio & Cacciola, 2012). Due to this increase in energy consumption, operations in coal mining and beneficiation processes have been highly mechanized to meet the demands. This mechanization has increased the quantity of raw fine coal particles produced which contain high amount of ash-forming mineral matter (slimes). Aplan et al., have reported that the major constituents of ash-forming minerals in U.S.A coal are clay minerals such as kaolinite, montmorillonite and illite (Aplan, 1997). Conventional froth flotation for fine coal cleaning suffers mainly from two major problems: 1) Low recovery of ultrafine coal particles due to slime coating by ash-forming minerals, and 2) The lack of selectivity, which results in the flotation of middlings and entrainment of mineral fines in the froth (Polat et al., 2003). Slime coating on both valuable and air bubbles have been proposed to explain the observed reduction in flotation recovery especially when fine grinding is required. In this case mineral matter may be degraded to extremely fine or colloidal sizes thereby creating difficulty in the water clarification process such as flotation. Slimes inhibit bubble-particle attachment, and increases reagent consumption due to the increase in solid/liquid interfacial area, resulting in low coal recovery."

Jan 1, 2015

By John A. Riddle

Some of the pitfalls and problems in selecting and applying corrosion-resistant materials in uranium plants are discussed, together with some suggested solutions. Includes some cost data.

Jan 1, 1979

By R. B. Elver

The St Lawrence Seaway, a deep-water canal system between Montreal and Lake Ontario, was opened for navigation on April 25, 1959. Prior to the opening of the new Seaway, small boats known as canalers and a few deep-sea carriers, primarily from Norway since World War II, were the only ships able to journey past Montreal into Lake Ontario through the old Canadian St. Lawrence canal system. Thus it was necessary for many tons of bulk and general cargo to be shipped all-rail to and from Atlantic ports or to be transhipped to and from canalers. With the opening of the new Seaway, large Great Lakes bulk carriers and a much larger percentage of the world's shipping fleet are now able to sail directly from the sea to the heart of industrial North America. In this paper, the historical events leading up to the construction of the Seaway and the physical nature of the Great Lakes transportation system are briefly reviewed. Following this, an attempt is made to evaluate the effects of the new Seaway on Canada's mineral industry. Because the Seaway has been in operation for only one season, this paper must be considered only an interim report. Because of the importance of the Seaway to iron ore, this commodity will be dealt with in detail, although the effect on other mineral commodities such as coal, petroleum, nonferrous ores, iron and steel will be mentioned. At this time the author wishes to thank the various company and government officials who provided both factual information and critical opinions.

Jan 1, 1960

By R. D. Smith

The Bureau of Mines (BOM) evaluated the technology, capital investment, and annual operating costs of emission control for further reductions of lead in ambient air at the East Helena, Montana, smelter, and the Glover, Herculaneum, and Buick smelter-refineries in Missouri. This study seeks to analyze the technology available to the domestic primary lead industry for attempting to further reduce lead emissions below 1985 levels. Through enclosure of concentrate unloading and handling areas and all lead-processing buildings, followed by venting these enclosures to the atmosphere through baghouses and the application of appropriate local controls, emissions can theoretically be reduced by a total of 2,424 pounds of lead per day from 1985 levels at the three Missouri operations. Using conventional technology, aggregated additional capital costs of $250,014,000 and annual operating costs of $18,507,800 are estimated for the four operations, resulting in a total cost of $0.063 per pound of refined lead. Continuous drossing techniques would assist in meeting OSHA standards in process areas. Continuous drossing would change capital and operating costs to $258,344,800 and $16,104,700, respectively, for a total cost of $0.062 per pound of refined lead. First quarter, 1986 open market price for refined lead was $0.184 per pound.

Jan 1, 1986

By P. Bevilacqua, G. Ferrara, M. C. Williams, T. P. Meloy

Tabling is an old environmentally friendly separation unit operation. This paper models shaking tables and explores the action and design of riffles on shaking tables. By reassessing riffle shape and riffle patterns, significant improvements in tabling performance appear feasible. While table sales appear at their nadir, a high-tech environmentally friendly table may have a significant market in the coming decade. Riffles on a shaking table impact particle separation. Particles are affected by riffles and their exit position on the table is dramatically changed, Riffle shape determines how much the riffle will influence a given material. Moreover, riffle patterns influence the concentration of a given material and its exit points on a table. This effect of riffle placement and design is modeled in a spreadsheet. Major performance and separation improvements may he expected by improved table design. Two physical laws of tabling have been derived. These laws aid in the design of sophisticated high-tech tables.

Jan 1, 1995

By C. Hansen, J. Killey

This paper discusses the replacement of AEROFLOAT ® 1 25 promoter by AERO ® 5688 promoter at Sonora Mining Corp.'s California Mother Lode concentrator. Flotation concentrate is trucked 120 miles to a leach plant in Nevada, so the reduced mass resulting from higher gold grades and reduced talceous gangue and barren pyrite resulting from this change in promoters has brought about a major decrease in shipping costs. Preliminary laboratory testing indicated that free milling gold and controlled amounts of pyrite could be floated using Aero 5688 promoter with reduced dosages of Aero 350 xanthate.2 Extensive plant trials confirmed that the new reagent suite could indeed maintain gold recoveries while reducing total mass. Improved froth characteristics also improved operating flexibility in treating various ore types, and overall reagent costs have been reduced.

Jan 1, 1991

By M. Kuchta

A linear integer programming (MIP) model to solve the long-and short-term production-scheduling problem for sublevel caving operations is presented. The MIP model is designed as a multi-time-period problem to provide monthly schedules that meet production, blending and sequencing requirements. One of the most important issues during the development of the MIP model was the requirement of sequencing between blocks. In this mathematical model, unique constraints that ensure sequencing of the production from sublevels are developed. A suggested method of handling a large number of variables is also given. The MIP scheduling model was implemented on a data set obtained from the Kiruna Iron Ore Mine located in northern Sweden. The initial MIP model implementation was successful and provided a solution that optimized resource recovery while meeting monthly and yearly production constraints. The scheduling results obtained based on the Kiruna Mine are further presented and discussed.

Jan 1, 2003

By Robert G. Ditchburn

The Mariana arc is an ~1,400-km-long intraoceanic arc that marks the southern extension of the Izu-Bonin arc, and is host to 62 ?volcanic centers? of which at least 27 (21 submarine) are hydrothermally, or volcanically active. A surface ship cruise in early 2003 mapped the distribution of hydrothermal plumes emanating from these centers, followed by remotely operated vehicle (ROV) cruises with ROPOS in 2004 and Jason II in 2006. With the exception of one volcano (East Diamante), none of the vent sites visited by the ROVs were host to sulfide mineralization. Rather, they were characterized by high sulfidation mineral assemblages dominated by native sulfur. The sulfur was seen marking the vicinity of vent sites, or as sulfur ?chimneys? (e.g., NW Eifuku and Nikko), or more spectacularly as ?lakes? of molten sulfur, either occupying the summit crater of the volcano (e.g., Nikko), or perched on the flanks of the volcano, near the summit (e.g., Daikoku). Gas (H2S and CO2) was discharging through the molten sulfur. Evidence for these lakes to have either been substantially ?deeper? in their recent past (e.g., Nikko), or existing at other volcanoes (e.g., Seamount ?X?) is given by remnant ?pillars? of native sulfur that are reminiscent of rock pillars in lava lakes found along mid-ocean ridges.

Jan 1, 2008

By G. Markopoulos

Every year thousands of people from all over the world come to Mount Parnasse, visiting Delphi, the Parnasse ski-resort and other sights in the area of Fokida, available to all ages all year round. This region of Greece, is not only gifted with natural beauty, but also with valuable underground natural wealth: inside Mount Parnasse and the adjoining Ghiona Mountain, there are rich bauxite deposits - the ore from which aluminium is made. In this magnificent part of our country, any mining activities undertaken must be adapted to coexist within such an ecologically sensitive area. This demands an enormous effort, knowledge and the use of technology. This is definitely our Company's primary objective. Our company's (Silver & Baryte Ores Mining Co. S.A.) activities in the area began in 1933, when Euripides Mavrommatis and the two Eliopoulos brothers, Elias and George, established "Bauxite Parnasse SA". Since then, ten thousand people have worked in these ore deposits, and 45 million tons of bauxite have been extracted. The full length of the underground excavations is more than 300 kilometers and 115 million cubic meters of limestone have been extracted on surface mining. In 1996, Bauxite Parnasse merged with Silver & Baryte Ores Mining Co. S.A. Now, the company exports more than 1.500.000 mt per year of bauxite to more than 15 countries around the world, offers a significant amount of job opportunities in the region, and imports valuable exchange into the country.

Jan 1, 2002

By Ivor Hawkes, Malcolm Mellor

INTRODUCTION There are currently around fifteen companies in the United States and Europe manufacturing hard rock tunneling machines. In recent years upwards of 200 hard rock tunnels of lengths up to 12 miles and diameters to the order of 30 ft have and are being successfully driven by over 100 different machines. It has been predicted that within the next decade over 2,000 miles of tunnels will be driven for transportation purposes in the United States alone (OECD Advisory Conference on Tunneling, Washington, 1970) and it is expected that eventually most tunnels including mine drivages will be excavated by machines. All tunneling machines have certain common basic functions; thrust is applied to drive or hold the rock cutting tools into the face, and torque is applied to rotate the cutting tools over the face so that they can continuously break out rock. The speed of head rotation, together with the torque requirement, determines the cutter head power. (The power required to push the head forward is usually negligible.) There are many factors which determine how successfully a given tunneling machine will perform in a given rock but one of the most important is effective utilization of cutter head power. This paper is a review of the specifications and performance of hard rock tunneling machines, obtained from manufacturers' catalogs, published literature, talks with manufacturers and visits to operating machines throughout the United States and Europe.

Jan 1, 1997

By Siegmund Babendererde

Introduction Lyon, with 1.1 million inhabitants, is the third largest city in France after Paris and Marseille. It is a lively industrial centre. Lyon lies at the intersection of many transport routes and at the fluence of Rhone and Saone. Like all large cities, Lyon is attempting to alleviate inner city traffic problems by constructing a metro. Metro construction in Lyon began with tunnels built by cut and cover methods along the streets. Deep diaphram walls, which were back anchored and toed into imperveous strata, formed the excavation walls. It is a very economic and simple method. However during the construction period, it has the disavantage of strangling urban life for several years. It is therefore increasingly being replaced by subsurface tunnelling methods. As it was decided to build the metro tunnel between the Guillotiere and St. Jean stations, and thus cross under the Rhone and Saone, the client, Semaly, put the contract out for a competitive tender in which the general parameters were defined. Line, level and construction method were left to the contractor. There was an extensive examination of the tenders, during which reference projects from competitors in Japan were visited, as well as in Germany. Finally the consortium of Dragages, Campenon Bernard, Colas and Hochtief was awarded the contract to drive this tunnel section with an hydro-shield and an extruded steel fibre concrete lining, a Hochtief design.

Jan 1, 1987

By Charles W. Daugherty, Eugene B. Waggoner

In the construction of recent subsurface projects, particularly mined openings and transit systems, it has been apparent that final costs were often greater than first expected. Because many overruns result from alleged differing site conditions, there was reason to suspect that pre-bid geotechnical investigations were inadequate for predicting subsurface geology. In 1982, nine federal agencies involved in constructing underground facilities funded the National Academy of Sciences' U.S. National Committee on Tunneling Technology (USNC/TT) in an effort to evaluate and clarify the relationship between geological knowledge and construction costs. That committee formed the special Subcommittee on Geological Site Investigations, which spent more than two years studying underground projects by examining contract documents and geologic reports, making site visits, and interviewing owners, designers and contractors. The study ultimately encompassed 84 mined tunnels and chambers and three deep shafts in the United States and eastern Canada. Data collected on geologic exploration, design and construction were analyzed and conclusions reached concerning whether and how site investigations need to be improved. The results of the study are published in two volumes by the National Academy of Sciences. Due to the recent completion date of the main report, it was not possible to prepare a summary for inclusion in the RETC Proceedings. However, the complete two-volume report, "Geotechnical Site Investigations for Underground Projects," can be obtained by writing or calling: U.S. National Committee on Tunneling Technology National Academy of Sciences 2101 Constitution Avenue, N.W. Washington, D.C. 20418 (202) 334-3136

Jan 1, 1985