Search Documents

By Joseph J. Feiler

Fires in underground coal mines are persistent problems anywhere in the world that coal is mined. Coal fires pose safety and health hazards in the form of mine subsidence, loss of energy reserves, destruction of property and surface improvements, and air pollution. In 1995, the US Bureau of Mines (US-BM), in cooperation with the Colorado Division of Minerals and Geology (CDMG),entered into a contract with Goodson & Associates Inc. (GAI) to design and field test the effectiveness of a new foamed grout technology called ThermoCell. GAI is a Lakewood, CO geotechnical and mining reclamation engineering firm. The company developed ThermoCell to control and extinguish underground coal fires. The viability of the special grout and the technology of application were established during a full-scale field demonstration at the abandoned IHI Coal Mine fire, near Rifle, CO. Following acquisition of additional funding by CDMG in 1999, Goodson returned to the site in April to continue the grouting to fully extinguish the IHI fire.

Jan 1, 2000

By D. Nutakor

Rock joint stiffness is not only a poorly known parameter, but also has no established laboratory measurement procedure. This paper presents methods used to determine the normal and shear stiffnesses of healed joints filled with vapor-altered minerals obtained from the Yucca Mountain site in Nevada. Results show that these joints behave linearly up to 85% of their loading history and are stiff with strengths very close to the strength of the intact rock. Factors that might have contributed to the linear behavior of these joints are discussed and areas requiring further investigation are provided. Joint normal stiffness ranges from 7.16 to 64.77 GPa/mm with an average value of 26.93 GPa/mm, while joint shear stiffness averages 11.41 GPa/mm and ranges from 3.09 to 28.41 GPa/mm. Young?s modulus of the vapor-altered joint infilling was calculated from the stiffness of the healed joint. Young?s modulus of the vapor-altered joint filling material averages 7.89 GPa and ranges from 2.15 to 19.43 GPa. Given the pervasive presence of such altered rock, usually in the form of sub-spheroidal 3-D pockets, this property should be of value in any numerical modeling attempting to describe the mechanical behavior of these tuff formations at the level of detail where inclusions might be a factor.

Jan 1, 2008

By Paul Wellman

The energy problem of the U. S; was emphasized by the oil embargo of late 1973 and early 1974 and it seemed for a time that the Federal Government, under pressure from the general public, might take some corrective action. However, this was not the case. With the gasoline lines gone and an apparent plentiful supply of petroleum products, public concern quickly dissipated., This country is more vulnerable to an oil embargo today than we were in 1973-1974 and this fact should be of concern to all our people. Since 1968, we have used oil and natural gas at a much more rapid rate than we have been able to find new domestic sources; thus, there is an increasing gap between domestic production and consumption and we have filled the gap with ever increasing oil' imports. These imports have increased at an alarming rate in the recent past, some 58 percent in 1976 compared with 1975. Imports are nearing 8 million barrels per day. Then, by applying some simple arithmetic, at $12 per barrel, the resulting trade deficit is $96 million per day or $35 billion per year. Obviously, this cannot be tolerated by our economy over a long period of time. Historically, we have shifted from one fuel to another as is shown in this slide. In 1850 about 90 percent of our fuel requirements came from direct combustion of wood, by 1900 we shifted to coal for 70 percent of our fuel, and now about 78 percent of fuel requirements comes from oil and natural gas. The difference is that the previous shifts were voluntary and the one facing us now is of necessity.

Jan 1, 1977

By Brad Murray

Evaluating the performance of a shielded tunnel boring machine (TBM) can be difficult because the ground cannot be observed directly and in relation to the TBM attitude within the excavation. It is difficult to determine whether performance problems are caused by ground loading, steering issues, fine muck packing against the shield, or migration of annular grout around the shield. The Arrowhead Tunnels Project in Southern California uses strain gauges on its shielded hard rock TBMs to detect shield strains early and correlate them with tunneling conditions, thereby increasing the chances that problems will be correctly diagnosed and addressed to optimize TBM performance. The frequent automatic measurement of shield strain has also been valuable by confirming whether remedial methods used to free the machine after stoppages are effective. This paper discusses the qualitative interpretation of characteristic strain patterns on the Arrowhead Tunnels TBM shields and discusses installation details and special considerations for setting up a strain measurement system.

Jan 1, 2008

By Charles W. Axten

Since the mid-1970s, samples of airborne and waterborne fibrous particulates have been collected in the area of the Northshore Taconite Ore Processing Facility by the Minnesota Department of Health (MDH), the Minnesota Pollution Control Agency (PCA), and the University of Minnesota. Indirect sample preparation has consistently been used although other aspects of the sampling methods and sites have varied and analytical procedures were altered over time as more accurate and precise microscopy methods were developed (i.e., phase contrast optical microscopy, transmission electron microscopy, transmission electron microscopy with energy dispersive spectroscopy). In the mid-1970s, levels of airborne fibrous particulate in the Silver Bay area averaged from 0.00030 to 0.03 f/ml. This level was significantly greater than levels of similar particulates in the St. Paul, MN area, although two of the Silver Bay sampling sites, considered individually, did not indicate levels of fibrous particulate markedly different than that seen in St. Paul. More recent sampling data (i.e., 1990?2001) indicate mean concentration of airborne fibrous particulates (amphibole-like fibrous particulates) of 0.0020 f/ml with a range of values from 0.0001 to 0.0140 f/ml. Such levels are not significantly different from those seen in other non-urban environments in the US and Europe. Concentrations of fibrous particulates in water samples were higher in the mid-1970 when iron ore tailings were being deposited in Lake Superior, but since the tailings have been deposited on land waterborne levels of fibrous particulate in the Beaver River have remained relatively constant averaging in the range of 7.5 MFL. This level is only slightly in excess of the current EPA drinking water standard for fibrous particulates. Review and consideration of this data is important in determining the potential health risks associated with airborne and waterborne fibrous particulates in the areas of the Northshore Taconite Ore Processing Facility. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Asbestiform fibers; Fibrous particulates; Cleavage fragments; Phase contrast optical microscopy; Transmission electron microscopy

Jan 1, 2007

By Robert C. Horton

The Getchell Mine is located on the east flank of the Osgood Mountain Range in the Potosi Mining District, Humboldt County, NV. Mining in the area first began in 1883 for copper, lead and silver in skarn-related deposits. Tungsten was discovered in the skarns in 1916 and was mined sporadically until 1957. The first major discovery was made in 1933 when two Winnemucca prospectors, Edward Knight and Emmett Chase, found gold at the present site of the Getchell gold mine. In 1934, after a small amount of preliminary prospecting, the claims were purchased by Noble H. Getchell of Midas, NV. The Getchell Mine Inc. was organized and exploration and development work began on a broad scale. Major funding was provided by George Wingfield and investors he assembled. Laxalt described Wingfield’s immediate history prior to his financing of Getchell as follows.

Jan 1, 1999

By Shamim A. Dar, & Samsuddin Khan, & K. F. Khan, Mohd Shuaib

The Late Paleocene–Middle Eocene phosphate nodules of Solan District of Himachal Pradesh belong to green facies of Subathu Formation of Sirmur group. Field observations indicate sporadic distribution of phosphatic nodules in the yellow brown to rusty brown, buff-colored bleach shales. Phosphatic nodules are dull earthy to dark grayish in color and break with sharp and conchoidal surfaces. Studies of phosphatic nodules using petrological microscope, X-ray diffractometry, and scanning electron microscopy (SEM) attached with energy dispersive X-ray (EDX) reveal that cryptocrystalline apatite (fluorapatite) is the dominant phosphate mineral. Silt sized silica is the dominant gangue, whereas pyrite and muscovite are present as minor gangue. The phosphate minerals occur as oolites, pellets, and cryptocrystalline apatite in the groundmass. Silica veins form a network replacing the original phosphatic matrix. Brown to brownish black color may be attributed by the organic matter in the phosphatic nodules. Completely phosphatized radiolaria and partially pyritized planktonic foraminifera are observed. There is corroboration of organic matter in the form of microbial filaments in the groundmass of apatite. The findings in the present investigation indicate that the different forms of the minerals, their texture, and distribution in the phosphatic nodules might be due to environmental vicissitudes in oxidizing to reducing conditions followed by replacement processes. Presence of microbial filaments may be due to the active role of microorganisms during the formation of these phosphatic nodules.

By Shamim A. Dar, Mohd Shuaib, K. F. Khan, Samsuddin Khan

The Late Paleocene–Middle Eocene phosphate nodules of Solan District of Himachal Pradesh belong to green facies of Subathu Formation of Sirmur group. Field observations indicate sporadic distribution of phosphatic nodules in the yellow brown to rusty brown, buff-colored bleach shales. Phosphatic nodules are dull earthy to dark grayish in color and break with sharp and conchoidal surfaces. Studies of phosphatic nodules using petrological microscope, X-ray diffractometry, and scanning electron microscopy (SEM) attached with energy dispersive X-ray (EDX) reveal that cryptocrystalline apatite (fluorapatite) is the dominant phosphate mineral. Silt sized silica is the dominant gangue, whereas pyrite and muscovite are present as minor gangue. The phosphate minerals occur as oolites, pellets, and cryptocrystalline apatite in the groundmass. Silica veins form a network replacing the original phosphatic matrix. Brown to brownish black color may be attributed by the organic matter in the phosphatic nodules. Completely phosphatized radiolaria and partially pyritized planktonic foraminifera are observed. There is corroboration of organic matter in the form of microbial filaments in the groundmass of apatite. The findings in the present investigation indicate that the different forms of the minerals, their texture, and distribution in the phosphatic nodules might be due to environmental vicissitudes in oxidizing to reducing conditions followed by replacement processes. Presence of microbial filaments may be due to the active role of microorganisms during the formation of these phosphatic nodules.

By Peter B. Dowden, Robert A. Robinson

Boulders, frequently found in tunnels excavated through soils, can pose major problems for full face TBMs in terms of slowing or halting the tunnel advance, cutter damage, and abrasive wear. The paper aims to consider the problem as a whole, from the geological characteristics of boulder sites, to the appropriate physical design of theTBM, and its operation in boulder-laden soils. In addition, visualization of boulders and other subsurface obstructions by seismic methods and ground penetrating radar are reviewed. The paper will assist the construction planner in assessing the risks and preparing appropriate specifications.

Jan 1, 2001

By J. E. Friant

The Mini-DiscTM cutter drill bit is a radical design departure from the traditional tri-cone rockdrill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-DiscTM drill bit, referred to as the “Disc Bit” has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory can not shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By John Hillman

The reconstruction of the British mining industry which began shortly after nationalisation in 1947 continued until well into the 1950s with the support of the Government. This support diminished as plentiful supplies of cheap oil from the middle East made many coalmines un¬economic. The planned rundown which followed was foreshadowed in the 1965 White Paper which outlined the financial measures to speed the closure of uneconomic collieries. The decline appeared likely to continue into the 21st century as the role of coal in UK energy requirements became less and less significant. This policy was well on course in 1973 when the oil crisis led to a complete reappraisal of the position. A Government examination in 1974 of the coal industry then supported the National Coal Board's general strategy of major capital investment as set out in its 'Plan for Coal' (1). Plan for Coal aimed at halting the intended decline in the industry's capacity and restoring it to 120 million tons of deep mined output in 1985. The Plan proposed action along the following lines (a) increase output by major Investment in construction at existing collieries with sufficient reserves to give 13 million tons per annum extra output (b) invest in extending the life of existing collieries by gaining access to additional reserves, to give 12 million tons per annum extra output © by sinking new mines, produce an extra 20 million tons per annum. Figure 1 shows the contribution (2) expected from each of the three sources up to 1990/1. The measures taken were expected to offset the inevitable exhaustion of existing pits and provide the additional 40-42 million tons capacity needed to restore annual output in 1985 to 120 million tons. Parallel to this programme for expansion of deep mined output, opencast mining was to produce 10-15 million tons per annum. A recent review however, indicates that new mines are likely to yield only 10 million tons per annum by 1985, mainly owing to the need for public inquiries into proposals for new mining and the resultant fact that planning approval takes 'much longer than originally expected. Nevertheless the objective of 120 million tons deep mined output by 1985 is still considered achievable of means of a greater contribution from existing mines. This programme was originally estimated to cost 2,-56 million dollars at March 1974 prices, out revised estimates of the cost of Plan for Coal indicate that it may now exceed 6,960 million dollars at mid-1977 prices. Plan for Coal includes a substantial investment in new and reconstructed coal preparation plaints. At mid-1977 prices more than 322 million dollars Ls so be invested in coal preparation projects in the UK, at the rate of, about 70 million dollars a year. This rate 3f capital expenditure has been maintained over the past three years and covers investment in a wide range of coal preparation coals for the power station, coking and domestic markets.

Jan 1, 1978

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named '3D Incremental Analysis based Stope Optimization' was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012

By I. A. Kunasz

This paper is not intended to review and re-state general information on lithium, but rather to analyze the paradigm that has caused such a rapid rise in lithium production and the development of new lithium producing centers. Details on pegmatites, brines, concentrate and chemicals are amply covered in a number of publications ? SME?s Industrial Minerals and Rocks, Industrial Minerals, Roskill and a host of other publications. There is no question that the latest interest in lithium has been driven by the potential development of the electric car. This stimulus prompts one to recall two symposia: 1. ?Lithium Resources and Requirements be the year 2000?, organized in 1976 by the U.S.G.S. in Denver (1) and the sequel 2. ?Lithium ? Needs and Resources? at Corning, N.Y. (2).

Jan 1, 2011

By Paul F. Gnirk, Ralph A. Wagner, Joe L. Ratigan

This thermomechanical analysis used the finite element method to investigate the behavior of crushed salt backfill in a waste disposal room situated in a salt dome repository. The first of two objectives was to determine the transient temperature rise and degree of thermomechanical consolidation that occur in the backfill as a function of drillhole depths. The second objective involved the evaluation of closure due to salt creep of unlined emplacement drillholes and the determination of pressure on steel sleeve liners in the drillholes should liners become necessary for canister retrieval. The retrievability period was considered to extend for 25 years after waste emplacement. The canisters were assumed to contain ten-year old high level waste with a thermal output of 4.3 kW at the time of emplacement.

Jan 1, 1981

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda’s mine production goal was set at 500,000tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: - Combined the exploration and business development groups - Formed teams to search for and respond to opportunity - Made our geologists more business minded and our engineers more optimistic - Went global - Set clear thresholds, farmed out the marginal properties, fast tracked the others - Focussed reconnaissance exploration where we had a clear competitive advantage - Became a “flexible” partner to both juniors and seniors

Jan 1, 1999

By D. Z. Mraz, R. S. Jones

Unlike in coal mines where caving methods are used, the subsidence over potash mines in Saskatchewan, Canada, is a function of gradual mining convergence. Because of the presence of high pressure water aquifers over the evaporite salt formations, the mines have to be designed as regionally stable and no caving is allowed. The extracted area converges gradually and the convergence is mainly a function of the extraction and the mining method employed. Consequently, the subsidence rate is very slow and the bridging of the over-lying strata is a considerably more important phenomenon than elsewhere. The paper evaluates a case history of convergence and subsidence in a deep potash mine in Saskatchewan.

Jan 1, 1986

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

By Franziska Wolf, Rainer Ellmies, Helmut Mischo

"Mining is an important part of the economy of Namibia. In 2016, 11.1 percent of the GDP was the result of mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists of an underground mining operation.The global annual production of fluorspar is approximately 5.4 to 6.3 Mt (6 to 7 million st) (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu has produced on average about 45 kt/a (50,000 stpy) in recent years (U.S. Geological Survey National Minerals Information Center, 2015).The Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an openpit mine with four individual pits (A-D) since 1980. In 2014, the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently, Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village.The intent is to develop a concept for the further underground development of the mine. There are still about 6.3 Mt (7 million st) of measured resources left in the deposit, with an average grade of 27.5 percent CaF2. This study focuses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged.For solving the task to design the mine, a site visit for data collecting was conducted. Resource estimations were calculated based on existing drill data, and consequently, block models were created. The development of the mine design included the selection of the most suitable mining method, mining technology and mine organization. Moreover, some economic considerations are pointed out, followed by a profitability assessment."

Jan 2, 2018

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel's support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

While the United States and the rest of the world struggles with record-setting oil prices Canadian oil sands producers are ramping up production to meet demand for oil while also fighting against a host of negative images. In recent months, the price of oil has skyrocketed. Most of that oil comes from Saudi Arabia. In Alberta, Canada there are unconventional oil reserves that rival those in Saudi Arabia in the vast Canadian oil sands, sometimes called the tar sands. Proponents of the oil sands say that Alberta?s oil sands can be a secure source of oil and energy for the United States for many years to come. With new mining and drilling projects, the industry has said that it could quadruple its production to nearly 4 million bbl/day by 2020. Time magazine once called the oil sands, ?Canada?s greatest buried treasure that could satisfy the world?s demand for petroleum for the next century.? So why hasn?t the United States embraced this close, politically secure source of energy? Because, getting usable fuel from the oil sands can be a dirty business, say opponents. The oil sands are a combination of clay, sand, water and bitumen. It is a heavy, black, thick oil. Oil sands can be mined and processed to extract the oil-rich bitumen, which is then refined into oil. The bitumen cannot be pumped from the ground in its natural state. Instead, tar sand deposits are mined, usually using strip mining or openpit techniques, or the oil is extracted by underground heating with additional upgrading. These methods require a huge amount of energy and water and produce a large amount of carbon emissions. Environmental groups that have long spoken out against the oil sands projects got some political backing in the United States in June when a group of mayors from large U.S. cities spoke out against the oil sands, as did presumptive Democratic candidate for U.S. president Barack Obama?s senior energy advisor. During a convention of large-city mayors in Miami, FL, Alberta?s oil sands were singled out in a nonbinding resolution calling for national guidelines to track the lifecycle impact of different types of fossil fuels. The resolution urges cities not to use unconventional sources of energy with a large carbon footprint, such as liquid coal and oil shale and oil sands.

Jan 1, 2008