Search Documents

By Reginald E. Reid

Mining on Bureau of Land Management (BLM) administered lands is affected by Federal laws and regulations requiring the mining industry to plan for the environmental consequences of surface disturbance. Regardless of the requirements for obtaining a claim, permit, lease or contract to mine, a notice or a mining and reclamation plan will be submitted and an acceptable environmental document must be prepared prior to mining. A bond may be required based on the results of the environmental evaluation, public interest and the operator's past history of compliance. In several areas, Federal requirements are different from California's requirements under their Surface Mine and Reclamation Act (SMARA). Therefore, the BLM is negotiating with the State in order to work out problem areas of responsibility and duplication of effort.

Jan 1, 1984

By Dennis Greene

Real-time GPS position monitoring of mining equipment is becoming more and more commonplace. Digital mining plans can now be used onboard properly equipped earthmoving equipment and excavation status is available in real-time via high bandwidth data radio systems. These systems provide a closely integrated link between operations and planning. No longer must operations wait for or be hindered by insufficient survey marks, nor is engineering delayed by lack of timely mine status information. Unprecedented efficiency gains become feasible -from the engineering office, to drilling and mucking, to reclamation, as well as in mine construction projects. Direct economic benefits of these systems will be explored as will the less tangible, but very significant, indirect operational efficiency gains.

Jan 1, 1998

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation located near Beulah, North Dakota. As part of the mining process, Coteau removes and replaces thin layers of suitable plant growth material (SPGM) generally ranging in thickness between one and five feet. Historically, tractor-scrapers completed this work; however, rising tractor-scraper costs and increasing haulage distances sent Coteau in search of a lower cost method resulting in the acquisition of a backhoe/truck fleet in 1995.

Jan 1, 1997

By S. Cotten

The concept for a Mine Escape Vehicle (MEV) is motivated by the desire to enable personnel to evacuate a mine rapidly as the first and most desirable response to any underground emergency. Under a NIOSH contract, Raytheon UTD developed a conceptual design for a vehicle that coal miners could use to facilitate their rapid exit from an underground coal mine in the case of emergency, including fire or explosion. The vehicle requirements include the capacity to provide life support functions for a number of miners, operate in an oxygen deficient, low or no visibility atmosphere, and travel at speeds faster than miners can walk out of the mine. To develop the MEV concept, three primary tasks were identified and executed. The first task focused on developing a realistic concept of operations (CONOPS) and associated high level vehicle requirements. The second task identified and evaluated currently available equipment and technologies that could be applied to address the CONOPS. The final task developed a design concept that integrated the identified components for the five (5) MEV sub-systems to provide the foundation for future detailed engineering design and prototype construction. The resulting MEV design concept is centered upon retrofitting existing mine personnel carrier chasses with available, mine-worthy equipment capable of addressing the MEV requirements. This approach offers a practical and economic avenue to prototype development and delivery with minimum lead-time and risk. Furthermore, by integrating familiar and available equipment into the design and CONOPS, the resulting Mine Escape Vehicles should also be more readily accepted by the mining industry.

Jan 1, 2010

By C. Dale Elifrits

Observations made from laboratory analysis of samples of fine-grained argillaceous materials (shales) subjected to various changes in moisture content have been correlated to loss of strength in the rock material. This reaction to a change in in-situ conditions (subsequent to mining) at a mine site combined with the observed relationships of surface-disturbing subsidence features at locations where the predominant overburden material is fine-grained, provides a predictive tool for the subsidence engineer.

Jan 1, 1983

By Ronald W. Marrs

Kimberlite contains a unique assemblage of minerals and exhibits a characteristic pattern of spectral reflectance in the visible and near-infrared wavelength region. This spectral pattern is readily discerned in well-exposed kimberlite outcrops, but becomes increasingly difficult to identify when outcrops are partially covered by vegetation or soils derived from non-kiaberlitic materials. Detection of poorly exposed kimberlite diatremes is possible using multispectral imaging techniques in which spectral bands are chosen to optimize contrast between he kimberlitic soils, non-kimberlitic soils and vegetation. Careful processing of the multi-spectral data is also essential in order to separate the spectral signature of kimberlite from the signatures of other components of the scene.

Jan 1, 1984

By T. S. Spicer

Inflammability and crossing point apparatuses were used to study the influence of increasing amounts of such inerts as ash, fly-ash, pyrite, limestone and Portland cement with several pulverized bituminous coals. The results indicate that it requires large proportions of inerts to substantially suppress the ease of ignition.

Jan 1, 1962

By P. A. Rittenhouse

Reserves of potash are more than adequate to meet future world demand for this primary fertilizer nutrient. The bulk of both reserves and current production is located in only a few countries. Recent attention has focused on potential development of smaller reserves to supply local markets in developing areas of the world. However, most new capacity in the next decade will be built in countries with large current production and reserves. The paper reviews current and future projects that will add to the world supply of potash.

Jan 1, 1985

By Perry N. Halstead

The primary objective of the structural geology portion of the Kennecott Copper Corporation-U. S. Bureau of Mines Pit Slope Stability Study was to determine the attitude, geometry, and spatial distribution of geologic structures of the west wall of the Kimbley Pit for use in designing a maximum stable slope for the pit. A corollary objective was to develop and refine techniques for collecting and analyzing geologic structural data with emphasis on numerical methods that could be integrated with other aspects of pit design. Surface mapping techniques used were a modification of conventional joint set mapping and a detailed linear sampling method. For subsurface investigations both oriented core and a borehole camera were used. It was determined that the major faults in the area were favorably oriented for mining a steep stable slope. The jointing or natural fracturing, although complex, was not random in attitude and consisted of several persistent fracture sets and a number of secondary sets. The attitude of the persistent fracture sets was favorable for steeper slope angles, and these attitudes were used in the design considerations. There was no significant difference between the attitude of the fracture sets determined from the former and new slope face.

Jan 1, 1968

By C. M. Brinckerhoff

Much has been written in the mining technical magazines about the caving system. Many of these articles were published in the Transactions of the American Institute of Mining Engineers prior to World War II. In recent years little has been written on mining methods or on the detailed planning always required. Block caving had primarily been used to mine deep copper ores in Africa, the United States and in Chile, although other ores had been mined by this same system. Asbestos ore had been caved in Canada, tin ore in Bolivia, molybdenum ore in Colorado, iron ore in Wyoming and Sweden, and limestone in California.

Jan 1, 1984

By Jack V. Hill

A unique type of grinding mill liner has been developed by Waagner-Biro A.G. of Austria. This liner system, termed an angular spiral lining (.ESL), was, successfully tested by Magma Copper Company's San Manuel concentrator in both their 10 Ft x 10 Ft (3.05m x 3.05m) and 12 Ft, 6 In x 14 Ft (3.81m x 4.27m) grate discharge wet grinding ball mills. Magma Copper's savings in power and grinding balls justified conversion of more than half of their twenty-six ball mills to the ESL system.1,2 The ASL system was provided by the Capitol Castings Division of Midland Ross Corporation, the exclusive licensee for such conversions. Capitol Castings proposed the following as expected benefits from installation of an ASL system in an 18 Ft x 21 Ft (5.49m x 6.40m) overflow discharge wet grinding ball mill at the Pinto Valley Operation of Cities Service Company: "(a) Reduction of power consumption per ton of ore milled = 12%, (b) Increased throughput = 6%, (c) Reduction of ball consumption = 6%."

Jan 1, 1982

By R. Ribeiro

The designers of the new Arafertil concentrator in Brazil provided for complete automatic control of the grinding circuit to meet the operating objective of maximum throughput at a specified grind. Analog control methods were selected because of proven reliability and simple maintenance, and in order to minimize commissioning time and effort. This paper summarizes the step-by-step effort required to progress from local loop control of certain individual parameters to an integrated system capable of achieving the design goal. Emphasis is placed on the practical aspects of commissioning a control system.

Jan 1, 1979

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009

By Dominick Mandalari, David Mast, Heather Ullinger, Juan Granja, Amanda Foote

The City of Akron will construct the Northside Interceptor Tunnel project, a U.S. EPA/ DOJ CSO Long Term Control Plan Project. The system will provide at least 10.3 million gallons of storage in a 16.5-foot finished ID and 6,660-foot-long rock tunnel. The system will reduce both overflow volume and number of overflow structures on the Cuyahoga River. The project includes deep drop shafts and more than 3,000 linear feet of 48 to 96-inch I.D. sewers installed by trenchless construction methods. This paper will discuss the project background, ground conditions, and other challenges overcome during the design phases.

Jun 13, 2023

By J. V. Thompson

The Powderhorn complex as a source of perovskite (calcium titanate) containing about 1.5% rare earths has been examined in several recent feasibility studies. Much promising exploration and process research has been done in recent years. This paper is presented with cautious optimism and with the acknowledgment that there may be some technical and economic areas yet to be explored. The Powderhorn carbonatite and alkalic stock in Gunnison County, Colorado, lies about 203 airlines km southwest of Denver at an elevation of 2450 to 2750 m (see Figures land 2). All of the mineable ore bodies are owned by Buttes Resources Company of Houston, Texas.

Jan 1, 1990

By Christopher Mark

Successful longwall gate entry design requires control of both vertical and horizontal stresses. Vertical, or overburden, stresses are most severe in the tailgate where they are concentrated by longwall panel extraction. Horizontal stresses, which are generally tectonic in origin, can be highly destructive during the development and headgate phases of longwall mining. The goal of this paper is to present the current state-of-the-art in detecting and controlling horizontal stresses. The information presented was collected through site investigations at 45 U.S. longwalls and an international literature review. The paper begins with a discussion of the present knowledge of regional in situ stress fields in the U.S. A review of available underground stress measurements from coal mines is presented, along with data collected by structural and petroleum geologists. The combined evidence indicates that a persistent ENE-EW trending stressfield is present throughout the eastern coalfields. Experience with horizontal stress in longwall mines is addressed next. The paper focuses on the northern Appalachian region, where the effects of horizontal stress have been most evident. Three case histories are discussed in detail, and the solutions each developed are highlighted. Observations made in the Southern Appalachian, Alabama, and Illinois coalfields are also described.

Jan 1, 1991

By J. A. Madonna

Universities and colleges in three countries, Australia, Canada and the United States, recognized the need to establish and/or reorganize geoscience programs at the vocational and two-year technical levels. To accomplish this goal, a cooperative study with industry in one state or province from each country was initiated. These include 1) Tasmania, Australia, 2) British Columbia, Canada and 3) Alaska, United States. Over one hundred mineral industry organizations cooperated in the study by providing information regarding their specific training needs for support personnel. The data gathered has been used to identify training areas for semi-skilled, skilled and technical personnel in geochemical mineral exploration, including, but not limited to, geological skills, geochemical skills, environmental skills and computer skills. With the areas of major educational need defined for geochemical exploration, an educational field skills model has been developed for the three levels of training. The depth of each level of education and the training objectives for the work force at each level will be discussed.

Jan 1, 1993

By R. Shields

"Hard rock mines move large volumes of material. But the conveyors essential to this movement suffer lots of problems, including carryback, spillage, dust, and belt wander. Many of these issues are created at the transfer points where the belts are loaded. This presentation will start with an overview of the latest transfer point systems that incorporate safety and serviceability by design. It will then report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, Nevada. Here performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine. THE IMPORTANCE OF TRANSFER POINTS Conveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance are the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created. The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material—cargo released in the form of carryback, spillage, or airborne dust—that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems, and issues with community relations. As estimate attributed to the U.S. Mine Safety and Health Administration (MSHA) notes that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points. TECHNOLOGIES TO IMPROVE TRANSFER POINTS A number of techniques to improve the performance of conveyor transfer points have been developed. They include: • Absorbing impact, to prevent damage to belt, belt support systems, and conveyor structure, and reduce spillage caused by the impact energy arising from long material drops or large lumps of material loaded onto the receiving belt. • Stabilizing the belt line, to eliminate sag that allows spillage and encourages material entrapment that can damage the belt. • Protecting the skirtboard seals, by sheltering the sealing strips from the mass of cargo pushing material toward the edges of the belt. • Using self-adjusting, multiple-barrier edge seals, to keep material on the belt by providing long-lived seal efficiency with minimum maintenance requirements. • Controlling and centering the belt’s path, to eliminate belt wander and the spillage and damage it can cause. • Allowing dust to settle, through the incorporation of chutework that provides expanded stilling zone and the use of dust curtains at the points where the belt enters and exits the transfer. • Adding supplemental dust control systems, through the installation of systems for passive dust gathering, water-based dust suppression, and/or active dust collection."

Jan 1, 2017

By H. V. Scotland III

Lafarge Corporation's Texas Quarry, in Baltimore MD, achieved a substantial expansion of pit reserves by removing an inactive underground mine. The day lighting program, designed, and completed in 1997, open pit mined more than 400 meters of room and pillar workings which were originally developed to recover high brightness Calcium Carbonate. The project proved to be a challenge throughout its course as the pit plan was modified and successful daylighting techniques were developed to remove the mine without adversely affecting the safety of the operation, quality of the stone recovered, or negatively impacting the surrounding community. The design parameters and techniques developed and implemented at Texas may prove of interest to other operators as they are faced with daylighting opportunities. This article will detail the challenges we faced and the solutions which made the project a success.

Jan 1, 1999

By John M. Hill

Automation technology has many facets, some well tested and proven, some yet to be put to the acid test of economic reality. In this paper, we will limit our purview to the former. Consider, if you will, an automated handling system combining high-speed conveyors and automatic devices on-line which not only provide signals for routing and sorting, but also format those signals for the production of manufacturing, inventory, shipping and billing paperwork. This is not futuristic, but practical and a realistic accomplishment. Therefore, the following discussions will address today's challenges not with tomorrow's solutions, but rather, with an established technology which is playing an increasingly prominent role in materials handling systems. Until recently, relatively modest importance has been attached to the timeliness of information feedback from the production or assembly line, warehouse or distribution center. Thus, initial applications of automatic identification equipment focused almost exclusively upon the control of materials flow - that is, routing, sorting, etc. However, these systems have performed successfully and quietly established an enviable track record as reliable materials control tools.

Jan 1, 1973