Search Documents

By James S. Browning

In 1975 bituminous coal and lignite production in the United States reached an all-time high of 637 million tons, an increase of 6 percent over production in 1974. The output, valued at $11.9 billion f.o.b. mines, was produced at 5,100 mines in 24 states (6). Coal mining is the largest mining industry in Alabama. Production from Alabama's mines in 1975 was over 21 million tons, and present projections forecast a steady increase in production, with tonnages almost doubling by 1985 (5). Of the total quantity of coal produced, about 16 million tons were consumed in electric power generation and the remainder was used for metallurgical coke production, extraction of chemicals and petroleum based products, and power for industry. The fact that 75 percent of Alabama's power is generated by burning coal attests to the importance of this fossil fuel to the State. Approximately 14 million tons of coal were produced by strip-mining methods in Alabama during 1975 and about 7 million tons were produced by underground mining during the same period. Surface mining is expected to continue at about 14 million tons per year, but by 1980 underground coal mining is expected to increase to about 25 million tons (3). About 7 million tons of surface-mined coal in Alabama is subjected to some means of washing or cleaning. The methods used are screening accompanied by heavy media separation, jigging, tabling and flotation. Some of the simpler approaches employ screening and jigging, or tabling. Except where flotation is used, the screen undersize fraction (finer than 0.25 inch) is rejected, with the result that 10 to 15 percent of the coal is lost. Thus, in the State of Alabama an aggregate of about 1 million tons of coal is wasted annually in the fines which are impounded from treatment of surface-mined coal. The use of the Humphreys spiral to concentrate fine coal was practiced as early as 1947. At that time the Hudson Coal Company (1) used Humphreys spirals to concentrate anthracite fines. In 1950, the use of spirals to treat fine-size

Jan 1, 1977

By R. J. Roman

The results of column leaching tests on 3 different mixed oxide/sulfide ores from a Chilean deposit are presented. The 3 samples contained different ratios of oxide copper minerals to chalcocite and chalcopyrite. The results of the column leach tests are interpreted in light of the shrinking core model for coarse particle leaching. The copper recovery from the oxide minerals and the sulfide minerals each conforms to the shrinking core model with the total recovery equal to the weighted average of the individual minerals. The use of column test results to predict field heap leaching results using the multi-mineral shrinking core model is discussed.

Jan 1, 1993

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By F. D. Wicks

This paper summarizes the direct operating cash costs for the Barrick Mercur open pit gold mine. A comprehensive, detailed system of cost management has been in effect for the life of the Mercur operation. This system provides the basic data for operations control and is the basis for drafting budgets as well as analyzing impact of change on operations costs. The ore body is complex geologically and metallurgically, requiring operators to pay close attention to mining and processing costs. The cost history provides data which enables analysis of changes in production levels, aging of the mine production fleet, and the impact of specific cost changes through time.

Jan 1, 1993

By M. Misra

The processing strategy for the effective separation of bitumen from low grade (< 10 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1979

By Vas P. Srinivasa

A comminution circuit is an important integral part of a mineral processing plant. Nearly 40% of the capital cost and 30 to 40% of the operating cost are taken up by the crushing and grinding circuit. Therefore, considerable care should be given to the design and selection of this circuit. Several factors affect the selection of a comminution circuit--energy consumption, avail- ability of the equipment, the remoteness of location, and availability of trained personnel, to mention a few. Each of these factors influences the choice. Selecting a comminution circuit strictly on lower capital cost may not be optimal. Crushing and grinding circuits are usually site specific and should be selected - only after careful analysis of all the factors involved. The objective of this paper is to show the effect of these factors, which are extranious to capital cost. Usually, the capital cost of a semiautogenous grinding circuit is lower than that of an equivalent conventional circuit. However, due to lower equipment availability and high power costs in certain locations, the economic advantage of lower capital cost is lost. Analysis indicates that a break even point occurs at a power cost of 5¢/kWh. This paper describes the procedure utilized for selecting the most economic comminution circuit and states the conditions applicable for each cominution circuit.

Jan 1, 1983

By C. W. Fitzgerald

INTRODUCTION Continuous mining machines are used in regular flat ore beds having uniform thickness. Since coal is the most common type of material occurring in such beds, most continuous miners are used for the extraction of coal from underground mines. The first continuous mining machine for under¬ground coal mining was introduced in 1948. In one machine, the continuous miner combines the functions performed by a conventional face drill, a cutting ma¬chine, and a loading machine. It breaks or digs the material out of the surrounding solid and transfers the material back through the machine chassis by means of a chain conveyor. The conveyor carries the material to a haulage system, usually a rubber-tired vehicle known as a shuttle car. Generally, continuous miners are used in seam heights from 890 to 3660 mm (35 to 144 in.). For seam heights of 1070 mm (42 in.) or less, the haulage system may be a multiple-bridge conveyor or battery-powered tractors that haul low-bed trailers. Proj¬ects are being undertaken by private industry and through government contracts to develop a continuous haulage system for all seam heights. As of 1976, the majority of continuous miners were of two types. The first type is the drum miner, which mounts the cutting elements on a series of drums across the cutting head of the machine, sometimes using a cutting chain to cut clearance for the gear drive. In the drum-type machines, the cutting head rotates parallel to the material face. The second type is the auger miner, which utilizes cutting elements mounted on two auger-type cutting heads. One head is located on each side of the machine, with the heads mounted per¬pendicular to the material face. Chain-head ripper-type miners/miners having rotary cutting elements with oscillating motion and twin-head boring-type miners have all been popular within the last 15 years. Although these are considered obsolete, some machines are still being supplied for specialized applications. GENERAL DESCRIPTION This chapter describes only continuous mining ma¬chines available as manufacturers&apos; production models as of September 1976. Figs. 1 through 11 illustrate some typical machines currently in use. Cutting Elements The cutting elements are the interface between the machine and the material being mined. In describing the cutting elements, consideration must be given to the differences between the drum- and auger-type machines, the bit-tip speeds, and the bit types. Drum-Type Continuous Mining Machines: Three of the four principal manufacturers of drum-type miners use multi-motor designs that provide separate a-c motors for driving the cutting elements. Gear trains are used to reduce the speeds of the motors to the rotational speeds of the cutting elements. One of the three suppliers drives the cutting elements of its low-seam models with a heavy-duty drive chain that is equipped with cutting bits; all other functions of this machine have separate motor drives that are either electrical or hydraulic. The fourth principal manufacturer generally provides two a-c electric motors, utilizing gear reducers, drive shafts, and hydraulically operated engaging clutches to power all of the operating functions, including the cut¬ting elements. Some drum-type miners use trim chains, equipped with cutting bits, to cut clearance for the gear drives. These trim chains vary from two 305-mm (12-in.) chains to one 760-mm (30-in.) chain per machine, de¬pending upon the manufacturer&apos;s design concept. In all machines other than the low-seam models that use chains to drive the heads, the trim chains are driven by sprockets on the drive shaft of the final cutterhead drum; therefore, the trim chains are not used for power trans¬mission to the cutting elements. In addition to cutting clearance for the gear drives, the trim chains provide uniform bit spacing all the way across the head and assist in moving the cut material to an area where it is either loaded directly into the miner&apos;s conveyor or is easier to load into the conveyor. On a drum-type mining machine, the cutting ele¬ments all rotate from the top to the bottom. Therefore, the recommended procedure is to raise the cutterhead to the maximum seam height, sump the entire machine forward to maximum depth by means of a crawler drive, and then shear downward until the cutter elements reach the floor level. The maximum sump depth varies ac¬cording to the drum diameter, the type of material, the floor conditions, and the operator&apos;s abilities. It normally varies an average of 460 to 760 mm (18 to 30 in.). Cutter drums are supplied with two types of cutting bit holders. Weld-on holders are attached permanently. Pin-on holders are replaceable at the face. Cutter-drum diameters over the bit tips vary from 660 to 965 mm (26 to 38 in.), depending upon the chassis height of the machine and the range of cutting heights. Auger-Type Continuous Mining Machines: As cut-

Jan 1, 1982

By J. P. McKinney

A mathematical model is presented for the electrokinetic dewatering of suspensions of phosphatic clays. The modeling approach couples a boundary-element model for solution of Laplace?s equation to a recently developed constitutive equation that relates the change in solids content with applied electric field and time. The observation that the electric field controls both the maximum solids content achievable and the time required to reach that value is shown to severely constrain the application of electrokinetic dewatering strategies to an entire clay settling area. The approach, however, may be feasible for implementation as part of a continuous plant process.

Jan 1, 2011

By R. L. Beatty

Bond International Gold&apos;s Colosseum gold mine was discovered in 1865. No recorded production occurred, however, until the 1930s, with production of about 19 kg (615 oz) of gold. The mine was closed in 1942 as a nonessential industry during World War II. The property was acquired by Dallhold Resources in mid-1986. Construction of a 1.1-million Mt (1.2-million st), carbon-in-pulp (CIP), cyanide mill began in November 1986 and was completed in September 1987. Minable reserves are estimated to be 9.5 Mt (10.5 million st), with an average grade of 2.1 g/t (0.061 oz per st). This article describes the general process flow and plant equipment. And it looks at the maintenance and operational problems encountered in the first six months of operation. Process description Ore is direct hauled from the open-pit mine 1.5 km (1 mile) to the crushing facility. There it is crushed to -152 mm (-6 in.) with a single- stage, 1.5-m x 1.2-m (60-in. x 48-in.), 186.5-kW (250-hp), Fuller-Traylor jaw crusher. The ore is then stockpiled in a 31.7-kt (35,000-st) reclaim ore pile. Lime is added to the crushed product as it is conveyed to a single 6.4-m x 4-m (21-ft x 13-ft), Hardinge semiautogenous grinding (SAG) mill, followed by a single 4.3-m x 7.3-m (14-ft x 24-ft) Hardinge overflow ball mill. After grinding, the slurry is thickened and then preaereated for three hours. Following preaereation, the pulp is leached with NaCN at a pH of 11, also for three hours. The slurry then goes through a seven-stage CIP circuit for 21 hours. Then the tailings slurry is preaereated for three hours before cyanide destruction using the Inco process. Loaded carbon is eluted using an Anglo American strip, followed by electrowinning on stainless steel wire. The stainless steel wire is transferred to refinery cells where the gold and silver is plated on stainless steel plates. Following electrore-fining, the gold-silver foil is removed, melted, and poured into dore bars for shipment. The crushing, milling, refining, and maintenance processes require 37 people. Crushing The crushing area required changes and modifications following start-up. Several areas are of specific note. Structural failures Rubber support cushion blocks located under the coarse ore bin failed. These were replaced with heavier, more durable blocks and have since appeared to be satisfactory. A severe structural vibration was encountered in the entire crushing facility. A mechanical engineer, brought in by the contractor, determined the structure needed more support and cross-bracing.

Jan 1, 1989

By John W. Nebgen

Surface water quality is determined by complicated interactions between water and land. Runoff--the flow of waters in surface streams and rivers-¬represents the total amount of water collected in a drainage basin or watershed that appears at the outlet of the basin. As the water flows through the basin, it is in contact with land and can pick up impurities from the land. Thus, surface waters are not pure--they contain impurities, or "pollutants," in vary¬ing concentrations determined by the nature of the land which they drain. The composition of surface waters thus tends to represent a steady state equilibrium between interactions of water and land. However, when man utilizes the land in the drainage basin or watershed, the natural equilibrium between water in the runoff and the land is disturbed. Such disturbances usually effect adverse changes in surface water quality, as new equilibrium conditions between land and water are established. These adverse changes in surface water quality can be thought of as "nonpoint pollution." Esti¬mation of nonpoint pollutant loads thus ultimately reduces to determining the magnitude of the differences between water qualities before and after man&apos;s disturbance of land within a watershed. The important key in making such an estimation lies in the determination of water quality in the natural or "back¬ground" condition of the watershed. In subsequent discussion in this paper, tools for making an estimation of background water quality will be described.

Jan 1, 1975

By William E. Bruce

Percussive drill calibration experiments performed by the Bureau of Mines on two drills are described. The use of a linear velocity transducer to determine piston velocity, blow frequency, and piston stroke length is discussed. Data are presented on the relationships between maximum work rate and feed air pressure. Penetration rates in nine rock types were measured for the same two drills. Physical properties of the nine rock types are presented in tabular and graphical form to show relationships between penetration rates and physical properties. Finally, conclusions are drawn as to the potential use of these data to predict percussive drilling rates.

Jan 1, 1970

By H. P. Hatch

Ash is a material that many people leave to nature to handle. Others sometimes sweep it under the rug to be disposed of by someone else. In our business we cannot do either. In fact the American Electric Power System spends many millions of dollars in plant investment costs to collect the material, and then many more millions to dispose it. In 1965 alone the coal fired steam generating plants in., the AEP System produced approximately 2,400,000 tons of ash, enough to fill 40,000 coal cars which would extend as a single train across the entire states of Ohio and Indiana. Even though our present ash production is large, this is only the beginning when we forecast the future growth of our system. By 1980 it is estimated that our generating capacity will expand to about three times its present size, and with coal as our primary source of fuel our ash production will increase proportionately to about 7 million tons a year.

Jan 1, 1966

By R. J. Sheets

In 2009 the Gold Quarry open pit mine, located 11 km northwest of Carlin, Nevada, USA, experienced multiple large-scale slope instabilities of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope instabilities occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower clay-rich sub-units of the Carlin Formation (Fm.). This deformation created preferential flow paths that allowed groundwater from the upper sandy sub-units to infiltrate low permeability clay-rich sub-units, thereby enhancing deformation of the slope toe which in turn destabilized the upper portion of the highwall. The outcome was a 160 m high slope instability that had a lateral run-out of 850 m. The effort to return the pit to ore production required both the geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This approach required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with blast induced, localized slope failures. Back-analyses applying numerical modeling indicated that the failure surface did not coincide with initial interpretations based on field observations; drilling results eventually confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the lower clay-rich sub-units. The outcome is a stable highwall within the Carlin Fm. following nearly ten years of repeated slope instability, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new open pit development.

Feb 23, 2014

By Thomas A. Morley

This paper deals with the minimization of ventilation costs for the controlled-flow mine ventilation network. Cost elements considered include the cost of power and the fixed cost of the fans. The problem is modeled in a mixed-integer programming format and solved via the branch and bound method. Computational experience with sample problems is discussed.

Jan 1, 1983

By R. R. Klimpel

The efficiencies of plant scale comminution processes are often evaluated by various indices that are calculated and/or measured somewhat independent of the performance of any associated downstream froth flotation processes. In order to compare some specific comminution factors such as energy utilization, media consumption, equipment utilization time, etc. comparisons of comminution efficiency independent of flotation behavior are appropriate. However, as more and more detailed plant level information is gathered on the joint and highly interactive nature of comminution and froth flotation, it is becoming increasingly obvious that knowing and using simple efficiency indices are not enough. What is needed are more performance related measures of the efficiencies of the combined size reduction -froth flotation system for effective plant level economic optimization to occur. The purpose of this paper is to present some examples of important interactions that influence the joint efficiencies of size reduction and froth flotation processes.

Jan 1, 1998

By A. Ramage

Since late 2010, CH2M HILL has been working with a confidential client who holds a long-term commitment to sustainable development (SD). The commitment is aligned with all three elements of the triple bottom line: people and society, ecosystems and environment, and financial and economic systems. These commitments are carried forward by the firm?s executives, managers, and operational sites, and are evident in materials posted on the company?s public website. These materials include a formal sustainability report prepared in accordance with the Global Reporting Initiative (GRI) guidelines (GRI, 2006), a report that outlines key SD challenges and progress toward the GRI targets, and a delineation of risks and opportunities outlined in the firm?s Form 10-K and Annual Report. In keeping with its commitments to SD targets, our client wished to consider SD issues in its decision processes for facility expansion or new projects. The company engaged CH2M HILL to meet this goal, based on working relationships established through existing contracts and CH2M HILL?s leading capabilities in sustainable solutions.

Jan 1, 2012

By Lloyd B. Underwood

In the event of a sudden nuclear attack upon the United States, it is imperative that vital command and control centers have a high probability of survival. One such vital facility is the North American Air Defense Command Combat Operations Center at Colorado Springs, Colorado. Known briefly as NOW, this installation when completed will be housed in large chambers excavated out of granite beneath the eastern slope of Cheyenne Mountain (Figure 1). The NORAD COC, a U. S. Air Force sponsored project, will serve as the primary collection and evaluation center for data concerning unknown aircraft, missiles, or space vehicles, which might bring destruction to North America. The data will be fed into high-speed computers and electronic equipment from outpost sources - radar, ballistic missile early warning stations and picket ships throughout the world. Electronically controlled display boards will make it possible to evaluate the tracking data instantaneously and to take appropriate defensive action1.

Jan 1, 1965

By Eric Sitorus, Septian Prahastudhi, Roy William, Wieda Azani

In July 2020, massive slope failure occurred in the southeast corner Grasberg open pit. This was the final episode in the breakthrough of Production Block 2 South (PB2S) of the Grasberg Block Cave to connect to the surface. This breakthrough had been rapidly evolving during the first half of 2020 and occurred as expected with no adverse impacts to safety or operations. To manage and safeguard the exposure to the workforce and operations, numerous hazards were identified and anticipated. The failure of the sill pillar between the open pit and PB2S cave was identified as the main area of interest and was closely watched during the failure process. This paper reviews the systematic approach developed to convert monitoring data into information around the collapse of the GBC PB2S cave sill pillar. The data that was interpreted consisted of micro-seismic, piezometric, ground-based radar and observational inspections. Geological structures on the boundary of the PB2S cave were clearly involved in the breakthrough process. As the cave propagation reached these structures and triggered instability, the resulting acceleration and breakdown were clearly shown by IBIS radar units associated with high movement in the slope. The focus of this paper is on the evolution of changes seen in the micro-seismic data and how it was used to understand the rapidly changing conditions of the sill pillar. The seismic parameters evaluated were event distribution, Es/Ep value, and the seismic moment tensor inversion. The changes of breakthrough indication seen in these parameters were substantiated by Shear Wave Splitting (SWS) analysis that showed a close correlation with the fractured zone above the PB2S cave as indicated by the increasing anisotropy.

Jan 1, 2022

By Felicia F. Peng

The plant data were collected from three streams around a dense medium drum for coarse coal cleaning operated at various volumetric ratio of medium-to-feed. The effect of the volumetric ratio of medium-to-feed (MF) and particle sizes on the performance criteria, g50 and Ep, of the dense medium drum. These measured data were adjusted and calculated for the yields and balanced relative density distributions by mass balanced method based on the statistic principle. These balanced data were then used to formulate the mathematical models of the separation distribution curves for the various feed size intervals. The correlation equations for the g50 and Ep as the function of inverse of the feed size, and MF and total throughput were established. A numerical algorithm utilizing the Secant method, based on the root searching principle, was developed for yield optimization and simulation of dense medium drum separation to improve the separation efficiency and hence the product yield. The relationships between the direct ash content and relative density of the particles in feed and the products were established and incorporated into the numerical algorithm for predicting the product quality.

Jan 1, 1996

By Christopher J. Bise

The potential of the coal reserves in the western United States for meeting future energy needs has been recognized for quite some time. However, two of the major constraints which have tended to limit the development of these reserves which can only be deep-mined are the great thicknesses of the coal seams encountered and their high pitch. Although new mining methods may need to be developed to recover these reserves, at least in the short- term the industry has to incorporate presently available equipment which were not originally designed for thick-seam mining. The purpose of this paper is to present an analysis of the various equipment that are in use today and their possible application to thick-seam mining. The paper also addresses the various ground control and safety considerations that are unique to thick-seam extraction.

Jan 1, 1981