Search Documents

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By Yuting Xue, Gamal Rashed, Zoheir Khademian, Morgan Sears

Mining has been recognized among the most hazardous industries in the United States, despite the significant reduction in injury and fatality rates over the past century. This study focuses on the ground-fall incidents classified in the Mine Safety and Health Administration (MSHA) database as “fall of roof, back, or brow from in-place” and “fall of face, rib, pillar, side, or highwall.” The main objective of this study is to conduct a comprehensive statistical analysis of the reported ground-fall incidents from 2010 through 2019 including both coal and metal/non-metal mines. Since most of the ground-fall injuries and fatalities occurred in underground coal mines and were attributed to falls of roof and rib, an additional analysis was directed to evaluate roof- and rib-fall incident trends in underground coal mines associated with the mining method, coal-seam thickness, mine size, and the seasonal effects.

By M. E. Rossi

Reconciliation of long-term block model reserves and mine production frequently shows significant discrepancies. This reconciliation can be done comparing the long-term block model reserves against a grade control model (generally, a model based on blast holes or production data). in this paper called an FI factor for tonnages, grade, and ounces; and also it should be done comparing the grade control model to the mill feed (or loaded to heaps) tonnages, grades and ounces (called an F2 factor). The long-term model usually contains blocks with dimensions larger than the size of the selective mining unit (SMU) of the operation. The smoothing effect of an estimator such as kriging will generally result in a grade-tonnage curve that does not match the grade-tonnage curve of the SMU's to be recovered. This problem is partly to blame for the reconciliation discrepancies found. In addition, in-pit perfect selection is impossible. and therefore the grade-tonnage predictions based on blast holes also need to be assessed, considering both unplanned dilution and the errors of estimation of the grade control model. This paper will focus on using conditional simulations to assess the uncertainty of the predicted grade-tonnage curve in terms of minable reserves, and in the framework of long-term mine planning. Quantifying the uncertainty in no uncertain terms is done in conjunction with a popular pit optimizer, which will yield not one, but several possible minable reserves, and therefore a range of possible minable tonnages and grades per pit shell or scheduled phase. This is a step further from the usual sensitivity analyses that are performed for deposit evaluation or development planning. Specifically, this approach takes into account the volume-variance relationship, the selectivity of the mining operation, planned and unplanned dilution. and carries the local uncertainty implicit in grade estimation into the mine design and mine planning phases. The motivation for the approach is discussed through an example, as well as a description of the procedures and steps involved.

Jan 1, 1998

By M. Jessop, V. O. Kofoed, R. Blanchard, A. Hughes

Willowstick has successfully employed a new Seismic Acoustic Resonance (SAR) method to improve seepage characterization through, beneath, and around dams. SAR is a passive seismic method that detects zones of higher permeability in the foundation and fill materials of a dam. Just as the ocean has tides, the earth’s crust experiences daily “Earth Tides” and is constantly in motion. Continual motion produces resonance signals that can be measured, interpreted, and modeled to identify zones of higher permeability within a dam and its foundation. The SAR results are analyzed in conjunction with the traditional Willowstick Method to better characterize seepage flow paths and patterns trough, beneath, or around a dam in three dimensions. When both methodologies, which use entirely different scientific principles, identify the same anomalous feature, a higher degree of confidence is gained in the results of the investigation. Willowstick has effectively utilized the SAR method on many successful dam seepage investigations. The two geophysical techniques when used in parallel have yielded complimentary results, with both methods providing beneficial information about seepage locations. This paper will detail seepage flow paths identified using both Willowstick and SAR methods for two case study tailings dams in Canada and the United States.

Feb 1, 2023

By K. T. Brashear

Since the MINER Act of 2006, the minimum static load of in-situ underground mine seals has been increased from 20-psi to either 50-psi if monitoring is conducted or 120-psi if left unmonitored. These minimum strength requirements in seals must be designed, built, and maintained throughout the lifetime of the seal. Due to this, it has become necessary to assess the effectiveness of non-destructive testing (NDT) technologies to determine seal integrity, which in this case, are explored using sonic waves and tracer gases. Through both small and large scale testing, two NDT methods will be evaluated for their abilities to determine integrity of the seal. A sonic wave technique to observe a change in wave velocity to identify faults within the seal material. As a NDT method, tracer gases may be used as a potential indicator of a connection between both sides of the seal material through a series of faults and cracks within the material itself. This paper reviews the history of underground mine seals and discusses the overall assessment of sonic waves and tracer gases to serve as NDT methods for estimating the integrity of these seals.

Feb 23, 2014

By Y. J. Wang

Stall or aerodynamic stall of axial-flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple-fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple-fan ventilation networks, design of the experimental setup for two-and three-fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1991

By William H. Pomroy

This report describes research leading to the design, prototype fabrication, and successful in-mine proof-of-concept testing of two improved stench fire warning systems for underground noncoal mines. The stench system, widely used in underground noncoal mines to warn of fire or other emergency suffers several serious shortcomings, including the toxicity of the odorant leading to debility in miners; reactivity of the odorant with iron oxide, resulting in unreliable warning because the odor may fade when transported long distances in steel pipe; lack of control over the rate at which agent is released into the air-stream, resulting in some work areas receiving unbearably high stench concentrations and other areas being missed altogether; lack of visual indication of system status, valve positions, or proper system operation; and excessively long stench transit times. In 1979, the Bureau of Mines, U.S. Department of the Interior, began research to upgrade the stench warning system. Two systems were subsequently developed which offer significant advantages over current systems.

Jan 1, 1984

By E. Tarshizi

This research project demonstrates the application of a mine system simulation and animation model in enhancing the efficiency of a truck-shovel operation and reducing the haulage environmental impact in an open-cut coal mine. In any mine, a key objective is to have enough equipment for production and not have excess to where it is counterproductive. Due to the advent of responsible mining, environmental regulations, and eco-friendly practices, these factors must also be considered in the analysis. The over-trucked situation at a mine will be discussed, i.e. when the number of trucks exceeds the optimum number of trucks a mine should have for the most productive/profitable mining operation. When the system has an excess number of trucks, truck utilization is reduced which impacts mine operation, capital costs and the environment, through unnecessary truck purchase, energy use, air pollution etc. A hypothetical surface coal mine layout was used for the simulation model.

Feb 23, 2014

By O. Salami, G. Xu

Fire accident is one of the most classic safety concerns in underground mines both in the USA and abroad. It may occur from pool fires due to leakages in hose or pipes, vehicle fires, or fires in tires and conveyor belts in the underground mines. It may also result from the storage of flammable materials such as gasoline, diesel, and explosives in the underground. When fire occurs in an underground mine, it releases heat, smoke, and other toxic gases such as carbon monoxide, and methane to the surrounding thereby making life unbearable to the miners. Furthermore, smoke greatly impact visibility in the underground which makes evacuation even more onerous and challenging. To this end, a thorough investigation of fire behavior and spread of toxic gases in a practical underground mine is imperative to develop a reliable emergency evacuation plan in an event of fire disaster in the underground mine. The objective of this study is to investigate temperature variation and CO spread along mine airways by conducting full-scale fire experiment in the underground mine. The results presented from this study are crucial to developing evacuation plans in underground mines. In addition, the findings from this study could be used to validate existing evacuation models.

Mar 2, 2022

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990

By A. Roper

Since the Toronto conference in May 2002, the International Council on Mining and Minerals (ICMM) has made progress on the road to sustainability. Fifteen of the world?s largest mining and metal producing companies and twenty-five associations have made a long term commitment to ICMM to improve the environmental and social sustainability of their activities. Sir Robert Wilson (Rio Tinto) assumed the chairmanship of ICMM in October 2002. By December 2002, the Council had approved a Strategic Vision and an operating plan for 2003. Both have been posted on the ICMM website (www.icmm.com). ICMM?s Operating Plan sets out three priority tasks: - Providing strategic leadership to achieve improved sustainable development performance in the mining, minerals and metals industry. - Contributing to international policy discussions on cross-cutting issues of importance to the industry, in collaboration with national and commodity associations. - Promoting dialogue and partnership with other organizations to catalyze sector?wide sustainability initiatives.

Jan 1, 2003

By S. -H. Kim

This work investigated the effect of the concentration of CO2 and lead contamination on the forest ecosystem. Changes of the plant growth, lead concentration in soil, plant, and soil microbial community caused by CO2 concentration (380 ppm and 760 ppm) and lead contamination (500 mg/kg) were measured. Plant growth was inhibited by 50% due to lead contamination. Particularly, shoot growth was inhibited more than the root. However, the root elongation was not affected by the CO2 concentration increase. The diversity of microbial population with AWCD (Average Well Color Development) and PCA (Principle Component Analysis) showed that the lead contamination has an effect com-pared to CO2 concentration. The Shannon index calculated from DGGE profiles was high in soil with Pinus densiflora, while the effect of CO2 concentration was not significant (P<0.5). The similarity of microbial community from each treatment showed that lead has an effect on plant growth and microbial community rather than the CO2 concentration.

Jan 1, 2006

By R. Hogg, T. F. Dumm

Procedures for particle size analysis on respirable dust from coal mines have been evaluated. Using respirable dusts dispersed in a laboratory dust chamber, size distributions measured using cascade impactors have been com- pared with the results of a variety of laboratory sizing methods performed on samples collected on filters placed side-by-side with the impactors. The laboratory techniques included centrifugal sedimentation, laser diffraction/scattering and automatic particle counting. The general agreement among the various methods was very good, with systematic differences which can be attributed to the different definitions of size used. Simple conversion factors have been obtained which can be used to transform the laboratory data to equivalent aerodynamic sizes. Similar comparisons have been made on samples collected in underground coal mines. Again, the results are in quite good agreement although small discrepancies were observed in some cases. These have been attributed to some degree of agglomeration in the airborne dust, leading to slightly coarser apparent distributions in the impactor samples.

Jan 1, 1987

By D. W. Park

Underground openings resulting from coal mining activities have been a serious cause of subsidence problems in the Warrior coalfield of Alabama, which is the 11th largest coal-producing state in the United States (National Coal Association, 1986). The problem will be even more serious in the future because 17 Gt (19 billion st) of Alabama&apos;s 22 Gt (24 billion st) of coal reserves are classified as an under- ground resource (Tolson et al., 1982). Subsidence data in this area has been scarce com- pared with other coalfields (Conroy, 1980; Dunrud and Osterwald, 1980; Gentry and Able, 1978; Hunt, 1979; King and Gentry, 1979). This paper discusses the results of a study of subsidence overlying two longwall mines that contrast each other. One of them (Mine #1) is a shallow longwall mine where the coal strength is very high, and the other mine (Mine #2) is extremely deep with a low strength of coal.

Jan 1, 1987

By A. K. Bakshi

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle&apos;s Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and a cooperating longwall trona mine in the Green River basin of Wyoming in the United States. The objective of the study was to evaluate the movement of longwall face air and exchanges between the face and worked-out areas to document the presence or absence of face airflow pathways between these locations. Tracer gas experiments using sulfur hexafluoride (SF6  ) were conducted to describe air movement on the face and in the mined portion of the active panel. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of gases emitted from the face and caved gob.

By Y. C. Kim

Using an exhaustive data set of Walker Lake, four different kriging techniques plus the inverse distance squared weighting were compared with regards to each one&apos;s performance in accurately estimating the block grades. The North-West quadrant of the Walker Lake data area was used because of its extreme variability of values and its distinct contour of the values. There were 1900 exhaustive data points in the selected area from which a total of 121 samples were drawn following the sampling strategy given in Isaaks and Srivastava (1989). The average of 5 x 5 exhaustive data points was treated as the true, known block grade. A total of 780 blocks, each block corresponding to the average of 5x5 exhaustive data points, were then estimated using the 121 sample points. The resulting estimates were then compared with the true known values to determine each technique&apos;s prediction performance. For this particular portion of the Walker Lake and for the given sampling strategies used, the obtained results for the global estimation are mixed. For the variable U which is much more variable, the rankings are; 1) Jackknife Kriging (JK), 2) Indicator Kriging (IK), 3) Inverse Distance Square weighting (IDS), 4) Ordinary Kriging (OK), and 5) Log-Jackknife Kriging (LJK). For the variable V, the results are; 1) OK, 2) IK, 3) JK, 4) LJK, and 5) IDS. When we apply several cutoff grades to the estimates to determine the conditional mean grades and tonnage, the above rankings generally get shifted around. Two exceptions to these cases are; a) UK for U and b) IDS for V. These two consistently ranked at the bottom.

Jan 1, 1995

By A. J. Getz

The paper reviews the status of the major precious metals projects in Australia, Papua New Guinea, Indonesia, the Philippines, and New Zealand. The projects may be at the stage of exploration, development, operation, or expansion. The paper covers project location, reserves, method of resource exploitation, anticipated production, and other unique conditions.

Jan 1, 1990

Longwall mining is a commonly used method of coal extraction that involves the complete removal of large, rectangular panels of coal. Longwall mining causes the immediate seam roof to break and fall into the void created by mining. The convergence of the surrounding strata towards the mining void causes subsidence on the surface. The subsidence magnitude is related not only to the mining depth, the topography, the geological features and the overburden materials, but also to the sequence of the strata overlying a coal seam. In additional to the vertical subsidence which is evident at the surface, there are also horizontal movements inwards toward the centre of the void, which cause the surface to tilt, bend, stretch and com-press. This paper presents a parametric investigation of the influence of the overburden stratigraphy to surface deformations due to longwall mining using 2D finite element models. Models simulate rock movement by applying equivalent edge load to the open roof.

Jan 1, 2008