Search Documents

By Hasan Sevim

This paper summarizes recent developments in modeling of underground coal slurry haulage networks for determination of optimum design and operating parameters. The model presented here is based on a stochastic dynamic programming formulation, applicable in any typical room-and-pillar and/or longwall mining configuration commonly practiced in the United States. The formulation and the structure of the model is general enough to handle design problems involving more than one face and mining method. Given the stochastic operating characteristics and a system layout, the model can be used to determine the equipment configuration and operating regimes that minimize the overall unit cost of coal haulage.

Jan 1, 1983

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

At the 25th Peruvian Mining Convention, the start-up of Antamina was called ?the mining event of the year.? Antamina, one of the largestcopper-zinc mines in the world, began operations in May 2001.Augusto Baertl is Executive Chairman of Compañía Minera Antamina, the operating company. He said in a convention address that Antamina would be in full production in 2002. ?I would like to stress that Antamina is, in every respect, a highly stringent operation, as it intends to be the Peruvianmine of the future,? Baertl said. ?Antamina has set the target of being, and remaining throughout time, a model mine as to technology, environmental practices and social responsibility.? [ ] In the areas of technology and operations, Baertl noted that ?we have incorporated the best engineering design available and state-of-the art technology for mining, grinding and transportation processes, among others.? In the environmental area, he said that ?we have carried out careful environ-mental impact studies and have incorporated modern technologies and methods to control and minimize any environmental impact.? In the social field, Baertl noted that ?our relationship with neighboring communities is being developed under the premises of the social responsibility philosophy.? These include popular consultation processes, environmental committees and conciliation discussion committees. The purpose, he said, is to encourage communities located within the area of influence of the project to find and lead by themselves their path toward sustainable development, beyond the life of the operation itself.?

Jan 1, 2001

By Yi-Hsuan Chen, Jürgen Brune, Candace S. J. Tsai, Alejandro Munoz, Connor Krause

This study highlights the significant presence of submicrometer- sized airborne particles in underground coal mines, especially around the belt conveyor drift areas. Using realtime instruments and gravimetric samplers, the assessment revealed that particle concentrations were notably higher in the belt entry compared to other locations, with a strong presence of submicrometer- and nanoparticle-sized dust. The study’s findings emphasize the importance of addressing small particle exposure, as these particles, composed of harmful substances like calcium, copper and iron, can pose serious health risks to miners. This research emphasizes the importance of improving air exposure estimation through more effective monitoring and characterization techniques to better understand and reduce workers’ exposure to hazardous airborne particles in the mining environments.

Apr 1, 2025

By G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

Considerable attention has been given to the restoration of low-level radioactive (<1000 pCl/g) sites contaminated during the early years of the atomic energy program. Current clean-up activities which involve the relocation of contaminated soils to licensed disposal sites have been shown to be very costly due to the large volumes of soils which must be excavated, transported and stored. Recent characterization studies conducted at Virginia Tech suggest that the volume of soil requiring disposal can be greatly reduced using mineral processing techniques such as classification, density separation and froth flotation. This article discusses the application of these technologies for soil remediation and describes a conceptual flowsheet for treating soil samples from two contaminated sites.

Jan 1, 1997

By Donald L. Freed

Design, development, factory test, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, and final machine configuration are reviewed. The AES is designed to overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1977

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964

By D. Kwak, S. Han, J. Kim, Y. Lee

"INTRODUCTION In carbonate rocks, it is difficult to characterize due to the high degree of heterogeneity in pore geometry. Carbonate rocks have various types of pore systems such as fractures and vugs, and this heterogeneity should be considered for more realistic prediction of oil production in carbonate reservoirs. This study carried out water flooding experiments using five carbonate rock samples in order to observe the change of physical properties. Firstly, qualitative and quantitative analyses were conducted for each carbonate samples by use of XRD and XRF to evaluate the mineral content. All samples are mainly composed of CaCO3 and after that, the ICP experiments were carried out for the water passing through the carbonate. As a result, it was possible to measure the quantity of CaCO3, MgO, Fe2O3 component in water and due to this effect, the permeability of carbonate was altered especially in the front part of the core. Finally, after the carbonate was saturated by 30 API crude oil, water injection to enhance the oil recovery was repeated and it was confirmed that the oil-producing characteristics are different depending on the dissolution characteristics of carbonate rock samples. CORE SAMPLE ANALYSIS Porosity and Permeability Experiment Porosity and permeability were measured. The procedures are as follows (Figure 1). 1. Measure the diameter and length of the dry core using Vernier caliper. 2. Put the core in the core holder, run vacuum pump until the inlet and outlet pressure gauge equal. 3. Saturate the core using ISCO pump to inject water at 650 psi 4. Measure the amount of water and calculate the porosity 5. Set up the outlet pressure at 500 psi. 6. The flow rate measure when the equilibrium 7. Calculate the permeability through Darcy’s Law. 8. Cutting of core upstream and downstream about 13cm, and measure the each of permeability."

Jan 1, 2016

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By Sepp A. Kutschera

are gaining increased interest for over­burden removal and ore production at large open cast mines. The application of bucket wheel excavators is still tied to soft un­consolidated rocks and soils, while belt conveyors can cope with all kind of matri­als restricted only by the top grain _ size. Therefore, mode of transport and the re­quirement of down stream ore processing de­fine the materials size distribution. These requirements are usually met by primary crushing or scalping. The paper discusses general applica­ tion criteria of bucket wheel excavator with systems primary for in-pit overburden crusher removal. and It _indeapits scalper units and discusses their technical and operational features. It further com­pares the capital and operating cost struc­ture relative to the syste

Jan 1, 1992

By D. G. Hartley

The major copper loss at Mount Lyell is in the coarsest particles presented to flotation. An analysis of data collected from the five primary and six secondary ball mill circuits showed that grinding was limited by low breakage rates in secondary mills, possibly due to oversize balls. For 5 months, the make-up ball size for one secondary mill was reduced from 50 to 30 mm. Frequent steady-state tests indicated that overall average breakage rates could be increased by about 70% using smaller balls. A mathematical simulation of the whole circuit with increased breakage rates showed that the resultant finer grind was likely to improve copper recoveries by about 22.

Jan 1, 1981

By Sahendra Ram, Priyadarshi Onam, Abhishek Kumar Singh

A numerical simulation study is carried out for assessment of stability of coal pillars having dirt bands by varying its size and depths. Physico-mechanical properties of dirt bands including thickness and its position in pillar system are varied in the simulation study. Results of the simulation study are correlated with the available empirical approaches of pillar strength are validated with field observations. It is observed that the presence of weak dirt bands significantly influences the strength of pillar. An attempt is made to develop correction factor for the available empirical approaches, which are developed without considering the weak dirt bands in pillar system. The findings of the study will be helpful for suitable design of different size of coal pillars at different depths and stages of depillaring operations.

Feb 1, 2025

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By James T. Baxter

Underground mining of limestone is becoming increasingly attractive in Illinois. Most quarries are near rivers on the western and southern borders where competition for land use is intensive. Increasing demands for stone can be met by expanded mining with access by edits in existing quarries and by inclines and shafts at downdip sites. Geologic, hydrologic, and engineering conditions indicate that deep mines in the Ste. Genevieve, St. Louis, Salem, Ullin, and basal Burlington Limestones of Mississippian age and in the Moredock Limestone Member of the Dunleith Formation of Ordovician age are possible, but development will require prudent exploration and planning to ensure that the product will be of good quality.

Jan 1, 1978

Geostatistical literature has been dealing with recoverable reserve estimation techniques for the last 30 years. There have been well established support correction techniques (Le. affine correction, indirect log-normal correction, etc.) to deal with volume -variance relationship globally in determining what will be the reserves above a cutoff grade during mining. Kriging has become the accepted technique in the mining industry for ore reserve estimation. Many large companies are using this method for gold and copper deposit modeling. In general, the estimates coming from kriging are smooth. The variances of the block grades estimated by kriging are often lower than the material that will be mined selectively. As a result, kriging tends to under estimate reserves at high cutoff grades and overestimates them in low cutoff grades. It is necessary to perform additional steps after kriging if the goal is to determine recoverable reserves at some cutoff and not the in situ resources. In the mining industry, it is becoming more and more common for the low grade heap leach projects to consider whether the higher grade portion of a deposit may be processed by a mill at higher profits. Similarly, a concentrator -refinery operations are implementing heap leach -SX-EW option for the lower grade portion of their deposit. These options are making it very critical to estimate the low and high end of the grade distributions more accurately. Ore reserve estimation is normally done by using widely spaced exploration data which has very small size support (Le. core samples). Selective mining is carried out on ore control that is based on closely spaced blasthole data normally averaged into larger polygons based on some cutoff grade. Estimated grades from exploration data need to reflect the variability of the grades of the selectively mined units if they are used without further adjustments to predict recoverable reserves.

Jan 1, 1997

By DeVerle Harris

The enthusiasm with which individuals have participated in mineral exploration in the development of this country testifies to the fact that there was once a very real probability of making a worthwhile discovery. Over the years, the discovery and subsequent exploitation of the accessible ore deposits have made the finding of new deposits progressively more difficult. Present day mineral exploration has evolved from the lone prospector with the grubstaker behind him to a very costly and complex business, involving large sums of money and a staff of experts in the fields of exploration technology. Exploration today must be carried out on a large scale to be profitable. With the involvement of large amounts of capital, there has been a good deal of interest in methods of optimization of the allocation of the resources of a firm &apos;engaged in mineral exploration. As a step toward this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firms operations so as to optimize its profit objective or more simply, to make exploration more efficient and effective.

Jan 1, 1964

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

By W. G. Pariseau

"BACKGROUND The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March, 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to begin mining in the south barrier pillar. Subsequent loss of ground control in August, 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterwards three rescue team members. An MSHA report describes the events in detail (MSHA, 2008). An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools; selecting the right tool for the job is essential. In this regard, a minimum program requirement is capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses. The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two dimensional finite element analysis indicated pillar safety was by no means assured (1, 2, 3). Geometry of barrier pillar mining is limited in two-dimensions, for example, crosscuts are not seen in vertical cross sections. While three dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three-dimensions. This technique involves a dual node – dual mesh concept. Both have been used separately in much earlier work, but are only now are used in combination. Estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale are possible (4). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2015