Search Documents

By J. Hahn

Modern high-performance disc filters such as the BoVac Disc Filter have set new standards in applications where large capacities of solids, liquids and air have to be managed through the filters. These disc filters have an enormous hydraulic capacity. For applications in mineral processing - with a special focus on tailings – which typically have high solids throughputs but low filtrate and air flows, this capacity can be used to expand the filtration area while maintaining the benefits of very good cake discharge even with thin cakes (4-5 mm) and a high filter speed. Research work over the last century has proven that increasing the filter area should be achieved by increasing the disc diameter. Because adding more discs leads to big problems with the cake discharge. However, as the disc diameter increases, the filter segments become longer and heavier. A suitable compromise was therefore found by doing both. The result is the first vacuum disc filter that offers significantly more than 300 m² of filtration area, but has no more than 6 discs.

Feb 1, 2023

By James E. Lawver

The agriculture industry has made great strides during the past decade to increase agriculture yields through increased use of fertilizers. Increased use of fertilizers may prevent or at least delay mass starvation due to the alarming increase in world population. Phosphate was added to soil as a plant nutrient in the forms of calcined bones at least 2 000 years ago, (1) and man has used phosphate minerals as a source of fertilizers in one form or another for at least 100 years. During 1977 the world produced about 116 million metric tons of phosphate rock, with about 86% used for fertilizers and another 4% for animal feed supplements. More than three-fourths of the total production comes from the United States, Morocco, and the Soviet Union. From a mineral beneficiation point of view, the major sources of phosphate rock and the methods of beneficiation can be classified as follows. Marine deposits not containing appreciable carbonate minerals, marine deposits requiring a francolite carbonate mineral separation, igneous deposits not containing appreciable carbonate minerals, and igneous deposits, requiring an apatite carbonate mineral separation.

Jan 1, 1978

By Ray E. Williamson

One of the prime objectives of the mine industry is to develop a low cost way to clean up what has been called "The Rape Of Mother Nature". The project falls under the broad umbrella of reclamation, which is now considered an essential part of the mining cycle. As such, it is being given full consideration in the initial planning of all surface operations. In most areas, if a proposed mining system does not lend itself to proper reclamation, it is not an acceptable system. By combining mining and reclamation plans, a producer not only can minimize reclamation costs, but can also restore the land to usefulness and insure continuing profits after a deposit is depleted. As long as fifteen years ago, many of the larger mining companies were already deeply involved in this extra cost work. Even then the involved companies were projecting a great need for a bigger bulldozer, Bigger than anything commercially available. At that time, the D9 tractor weighed about 60,000# bare weight.

Jan 1, 1975

By W. L. Freyberger

In many papers concerned with fundamentals of the froth flotation process, authors have considered the contents of a flotation cell to be comprised of two immiscible phases, the froth and the pulp. I (Of course, each of these phases is in turn made up of several solid phases plus air and water.) This generalized concept of the flotation system can be extended by considering the cell contents to include two phases: an extracting phase, the air bubbles plus the collector, which removes a selected mineral component from the second phase, the ore pulp. Thus, there is an analogy between a flotation system on the one hand, and chemical extracting systems, such a solvent extraction system or a leaching system, on the other hand. Such extracting systems may be operated in cocurrent or countercurrent fashion. This paper includes first a brief discussion on the general nature of cocurrent and countercurrent operation as applied to froth flotation, and then presents the experimental results of flotation of a specular hematite ore by each method, using a tall oil fatty acid as collector. Cocurrent Flotation A conventional flotation circuit involving roughing, scavenging, and cleaning flotation is illustrated schematically in Figure 1. In such a circuit the col¬lector, or extractant, and new feed ore enter together at the head of the rougher circuit, and flow cocurrently to the scavenger circuit where more collector is added. According to this practice, sufficient collector is added to the head of the rougher (and scavenger) so that the final tailings are of low enough grade to be discarded. Since the flow of collector and ore is cocurrent, the process consists of single stage contact between the extracting phase and the ore pulp. If the scavenger concentrate is recycled to the head of rougher, the overall circuit has some of the characteristics of countercurrent flow. In such a case part of the extractant (collector) is added at the discharge end of the circuit, and may

Jan 1, 1971

By Jr. Chesson

"Phosphate" is a misnomer as often used. The word is increasingly used to refer to any material containing phosphorus - an element essential to any form of life. Phosphate rock, a mineral - fluorapitate - is recovered from Florida's sedimentary deposits in particle sires ranging from 0.1 to 13.0 millimeter. This product of mining, washing, screening, and flotation is commonly called "phosphate". Its phosphorus content, measured and reported as P2O5, varies from 29% to 35%, and is essentially insoluble. "Phosphate" is also used to describe products containing soluble phosphorus obtained from acidulation of phosphate rock with mineral acids; primarily, sulfuric acid. Many miners have nearby chemical plants wherein phosphate rock is converted into upgraded products such as phosphoric acid, superphosohates, and ammonium phosphates with 45% to 70% P205, soluble and suitable for use as fertilizer. The rock and upgraded products are all commonly called "phosphate"; the plants, "phosphate plants' and the producers collectively are known as the "phosphate industry". The public in Central Florida generally loses identification of the individual operators that include major corporations such as IMC. Williams Companies, W.R. Grace, Mobil, Embark, U.S. Steel, Borden, American Cyanamid and others. They all become just a "phosphate company".

Jan 1, 1978

By K. Fair

Using an agitated column 203 mm (8") diameter by 1829 mm (72") tall with independent agitation units for the gas dispersion zone and the collection zones, respectively, permitted the independent evaluation of the attachment and the detachment mechanisms for the chalcopyrite/ silica system. Three particle size fractions were used in this study, i.e. coarse (+75 µ m), intermediate (-75 µ m + 10 µ m) and fines (-10 µ m). The optimum selection of the two agitation zones for the three particle size fractions were determined as a function of grade, recovery, residence time and air superficial gas velocity.

Jan 1, 1990

This paper examines the feasibility of combining network modeling and computational fluid dynamics for modeling of underground mine ventilation systems. Both simulation methods have specific advantages and disadvantages for analysis of mine systems. Network modeling is widely utilized by many operations and allows for assessment of current systems and simulation for planning purposes. Alternatively, CFD has been utilized only marginally by operations and is typically a research tool, requiring considerable computational power, complex models, and careful analysis and calibration of results. Network modeling allows for a holistic approach to the ventilation system, giving quantity, velocity and pressure in every branch, but CFD modeling can resolve the flow regime in 2-D or 3-D, which is idea when examination of an area on a more detailed basis is useful, such as dust and gas control. Integration of the two can allow for more flexible systems analysis. The feasibility of integration, along with application to limited underground mine data are examined.

Feb 23, 2014

By J. Fritz, V. Gangrade, J. Briton, K. M. Ajayi, M. L. Harris, G. Cole, M. Young

Mine workers using diesel-powered equipment experience the highest occupational exposure to diesel particulate matter (DPM). This problem could be aggravated in underground stone mines due to their unique ventilation challenges with the large openings for airflow. Hence, adequate ventilation in these mines requires a combination of effective ventilation planning and delivering needed air quantities using auxiliary fans and stoppings. To meet this challenge, the National Institute for Occupational Safety and Health (NIOSH) developed the Air Quantity Estimator (AQE) software as a mine planning tool to help underground mine operators estimate the air requirements necessary to dilute DPM in the main air stream to statutory levels. The major parameters required for the calculations are the engine’s horsepower, DPM emission rate, the percentage operating time, catalytic converter efficiency, and filter efficiency. In efforts to provide major updates to this software, this study describes the recent development of a revised version of the Air Quantity Estimator (AQE 2.0). With the revised version, users have access to a comprehensive database of over 40,000 pieces of equipment, can define their specific target DPM level, and can create specific equipment for a customized database, in addition to having an improved easy-to-use interface. The software output provides an estimated total airflow necessary to dilute DPM based on the projected emissions, and the user can generate a related results report. The results also provide the mine personnel with a tool to identify vehicles that are high DPM contributors and could further be used to optimize the ventilation requirement by making changes to the percentage operating time of the engine. This software provides the mine with a user-friendly tool that could help reduce the DPM exposure of workers.

Feb 1, 2023

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By Irina Melekestseva, Beltenev. Victor, Victor Ivanov

"One of the major problems discussed over the last years is a possibility of mining of seafloor massive sulfide deposits. In spite of the pessimistic points of view on their commercial development, they are still of great interest and continue to be studied (Hannington et al., 2011). Recently, Barriga (2012) paid special attention to the underestimated amount of massive sulfide hydrothermal fields and pointed to the importance of the buried fields and subseafloor mineralization.This study examines the geochemistry of seafloor and subseafloor precipitates collected at the Peterburgskoe (19°52´ N) and Irinovskoe (13°20´ N) hydrothermal fields (MAR) during the 34th cruise of the R/V Professor Logatchev in 2011. These fields were discovered by the Polar Marine Geosurvey Expedition in 2010 and 2011, respectively (Shilov et al., 2011; Beltenev et al., 2012). The Peterburgskoe field, associated with basalts, is located 16 km west of the main rift valley at the depth of 2800-3100 m at the junction of a large non-transform discontinuity with the second rift ridge parallel to the rift valley. The Irinovskoe field occurs at depths of 2700-2850 m and has a northwestern satellite sulfide site, both confined to an oceanic core complex (MacLeod et al., 2009), which includes mafic and ultramafic rocks. The details of geological structure of the fields may be found in the relevant papers.Diverse samples were collected from the hydrothermal fields: seafloor massive sulfides, Fe-hydroxide crusts, SiO2-rich sulfide-bearing precipitates, and subseafloor mineralized rocks (Melekestseva et al., 2014a). Massive sulfides may be subdivided on the Fe-rich and Cu-rich types. The marcasite-pyrite, pyrite, hydroxide-marcasite, and chalcopyrite-pyrite (Fe-rich) mineral types are dominant in the Peterburgskoe field at lesser amounts of sphalerite-hydroxide-chalcopyrite and pyrite-covellite-chalcopyrite (Cu-rich) massive sulfides. The mineralized sulfide-talc-carbonate-chlorite, chlorite-sulfide-quartz, and hematite-sulfide-quartz rocks host stringer-disseminated sulfides including chalcopyrite, covellite, and pyrite."

Sep 1, 2014

By D. Donison

The practice of blasthole mining is typically applied in competent ground conditions, primarily because of the open stope dimensions. At Magma Copper -Superior Mine, a field pilot project was completed examining a variation of blasthole mining in poor ground conditions. The results were very encouraging not only from a technical viewpoint, but also productivity viewpoints. This paper describes the pilot project and the resulting implications.

Jan 1, 1994

By S. Behl

A major limitation in developing successful selective flocculation schemes is the difficulty encountered in adsorbing the polymeric flocculant only on the desired substrate. In this paper a correlation between selectivity of flocculant adsorption and separation efficiency is outlined and a potential technique to achieve selective adsorption of flocculants is discussed.

Jan 1, 1992

By Guangyao Si, Ismet Canbulat, Xun Luo, Yi Duan

Routine analyses of seismicity and event locations are essential for coal burst risk management, especially in the presence of unfavorable and complex geology. In an Australian longwall coal mine, a small-scale seismic monitoring network was installed to monitor a section of a major dyke intersected by the roadway, which was classified as a coal burst prone zone. The Deep Convolutional Neural Network (DCNN) technique was adopted for automatically discriminating seismic events to assess seismicity in this zone. The discriminated seismic events were located with the Shortest Path Method based on the Boundary Discretization Scheme (BDS-SPM) for temporal-spatial seismic event distribution analysis. The results demonstrate that the seismic events are discriminated with an average accuracy of 94%. Moreover, the seismic events are more accurately located using the BDS-SPM with a 3D heterogeneous velocity model compared with results obtained with a homogeneous velocity model. The temporal and spatial variances in seismic activities identify that the rock fractures in the dyke zone are closely related to the longwall mining process and a local dyke has a controlling influence on the stress concentration in its vicinity.

Apr 26, 2022

By I. S. Parrish, D. W. Kappes, G. G. Austin

Micron-sized gold disseminated in lower Cambrian siltstone has been found at the Sterling mine near Beatty, NV. A shoestring-shaped body has been developed by central and fringe drifts and is being mined via a modified retreat room and pillar system. The siliceous ore crushed to 5.08 cm (2 in ) is stacked to 4.6 m (15 ft) over a layered sand, gravel, and impervious PVC base. Gold is leached using a 0.1% cyanide solution and deposited on activated coconut shell carbon. Stripping of the carbon by hot solutions of 1% NaOH and 20% Ethanol yields overall recovery of about 75% of the fire assay head.

Jan 1, 1983

By Donald S. Clarke

The Umuna epithermal precious metal deposit has provided the target for a simulated rock geochemistry exploration program, directed at bedrock exposed in the drainage system of eastern Misima Island. A geochemical halo to the deposit is readily recognised in the mafic meta-volcanic country rock. This halo is defined by anomalous results for both major (K, Na, Ca, Mg) and minor (Au, As, Sb, Cu, Pb, Zn, Ba, Rb, Sr, Cs, Bi, Ga, S) element geochemistry, extending further than 1km from the deposit. Such halos are sufficiently extensive to provide adequate exploration targets in the search for epithermal mineralisation, complementing mineralogic and secondary media geochemical investigations.

Jan 1, 1989

By G. Southam

Bacterial populations play an active role in mineral weathering in subsurface and near-surface environments e.g., supergene enrichment of Cu at Morenci, AZ. An in vitro bacterial biofilm model was used to examine the interaction between Sporosarcina ureae and ionic gold (which is toxic) or amino acid-gold complexes in gold mobility. The immobilization of ionic gold was between 80-90% for 1 week but as the available, cellular reactive sites became saturated immobilization decreased to 14% within 2 weeks. In the asparagine-gold system, gold immobilization occurred at a high rate (80-90%) throughout the experiment with limited toxicity towards Sporosarcina ureae.

Jan 1, 1999

By H. W. Gao

During the last decade, the feasibility of applying the in situ leaching technology to the recovery of copper from deeply buried deposits containing chalcopyrite has received much attention.(1-4) The major incentive for using this technology is that under certain circumstances, copper in deep underground deposits, which cannot be mined economically by conventional means, can be recovered economically. Basically, this technology involves rubblization of the deeply buried copper ore body followed by in-place leaching of the rubblized copper ores. Rubblization of the ore can be achieved by some suitable method such as the use of block caving mining. The rubblized chimney is then filled with water until the original water level is reached. Leaching occurs when the eater saturated with oxygen is introduced into the chimney- and flows through the fractured rock masses and within pores of rocks. As the dissolved oxygen oxidizes the primary sulfides, heat is generated. Because of low conductivity of the surrounding rocks, the generated heat is able to raise the temperature of the chimney. The increase in the temperature of the chimney and the relatively high content of dissolved oxygen in the leach solution under high hydrostatic pressure will result in an enhanced dissolution of the primary sulfide minerals. To ensure a successful application of the in situ leaching technology, a complete understanding of the effects of the ore particle size distribution, ore grade mineralogy, temperature, pressure, lixiviant concentration, pH, etc. on the rate of copper recovery is necessary so that copper can be recovered efficiently and the amount of copper extracted can be predicted. These can be achieved through mathematical modeling of the in situ leaching process and conducting laboratory tests. In this paper we will present a mathematical model that simulates the in situ leaching process as depicted in Figure 1. To model this process properly, not only the 'kinetic and thermodynamic aspects of leaching chemistry must be known, but the effects of heat generation, the physical aspect of fluid flow and other related multicomponent transport phenomena must be considered. Furthermore, since most factors involved in the leaching process change with time, a leaching system must be described using unsteady state equations.

Jan 1, 1981

By Donald T. Mylar

It is axiomatic that in designing a bulk material handling system the primary consideration is the functioning of the machines. The structure is secondary -its reasons for being are to support, enclose and provide access to the machine, for servicing. This results in a wide variety of supporting structures. Other considerations are: plant layout, local soil conditions, climate, local laws and codes, and last, but by no means least, the Customer's wishes.

Jan 1, 1971

By Georgene Renner

Due to disturbance of their traditional roosts, caves and tree hollows, more than half of the 44 bat species found in the United States and Canada now live in abandoned and inactive underground mines. The North American Bats and Mines Project was created two years ago by Bat Conservation International Inc. (BCI) in Austin, TX and the Bureau of Land Management (BLM) in response to the issue of mine closure and bat habitat. The partnership provides national coordination among government and private agencies and the mining industry to minimize the loss of bats living in mines. It also trains land managers on how to conduct cost-effective mine assessment and closure to protect both bats and people.

Jan 1, 1996

By S. M. Khandrika

Most of the coal presently used by the utility industry is cleaned at preparation plants employing wet processes. While water is the mainstay of coal washing, it is one of the least desirable components in the final product causing a reduction of the heating value as well as handling difficulties. Currently available dewatering techniques are inefficient for dewatering very fine coal (minus 325 mesh). The US coal industry has expressed serious concern about utilizing advanced cleaning processes such as column flotation because an efficient and economical dewatering process is not available.

Jan 1, 1992