Search Documents

By Dennis S. Kostick

Sodium is a silver-colored metal that is so unstable that it reacts violently in the presence of water, and chlorine is a greenish-colored gas that is dangerous and lethal. Yet the combination of these two elements forms sodium chloride, commonly known as salt, which is a white-colored compound essential to life itself. Salt is perhaps the only mineral in the world that is used virtually by every human being in every country. Although its importance has diminished over time, salt has had a profound influence on history. Sources of salt have determined the location of cities, such as Salzburg, Austria, Salzgitter, Germany, Salt Lake City, UT, and Saltville, VA. Populations have migrated in search of salt, and wars have been fought to obtain or to protect it. Although there is no written record of when prehistoric man first discovered salt, he probably instantly appreciated its unique and distinctive taste and sought more of it. He noticed animals were attracted to salt springs and salt licks, where they satisfied their innate cravings. Man used this knowledge to hunt for food; where he found the salt, he would find the animals. Because prehistoric man was not aware of his physiologic need for salt, he automatically received his salt requirements from the meat of the animals he ate. A Mesopotamian tale tells of a wounded pig that ran into the ocean and drowned. After being recovered from the ocean, where it was saturated in the salt brine, the pork was found to taste better than unsalted meat. It was not until man graduated from a nomadic to an agricultural society when he introduced vegetables and cereals into his diet that he realized he needed additional supplements of salt. The Sumerians ate salted meat and used salt to preserve food about 3500 BC. In approximately 1000 BC, the Trojans learned to use salt for preserving fish. The maritime civilizations, such as that of the Phoenicians, engaged in an extensive salt trade throughout the Mediterranean. Many superstitions, customs, and traditions surround the religious, social, economic, and political aspects of civilization. Although some commodities have provided the basis of some ageless metaphors and cliches (i.e., heart of gold, strong as steel, etc.), none are more commonly used than those pertaining to salt. Being "the salt of the earth" referred to a person's worthiness, as referenced in Matthew 5:13 of the Bible. Someone "not worth his salt" reportedly was used in ancient Greece in bartering salt for slaves. When a laborer was worth his salt, he was paid a salary (sal is Latin for salt), a term still in use today that dates back to Roman times when part of a soldier's pay was salt rations. Fearing those around him, the Roman leader Pompey was known to add a grain of salt to his drinks as a supposed antidote to poison. Hence, "taking it with a grain of salt'' is to regard something with suspicion. The earliest known record of salt production was in China about 2000 BC when Emperor Yu decreed that salt had to be supplied to the court as a tribute. Because salt was a commodity that had universal demand, governments often intervened to control salt production and distribution to generate revenue for major national projects. State-run salt monopolies were common in history, such as in Rome about 506 BC. Revenue was also derived from taxes levied on salt sales. The word gabelle refers to the direct salt tax used in France. This tax was so despised that it was a major cause of the French Revolution. Although the tax was repealed in 1790, it was reinstated in 1805 to raise revenue for war. France continued to used the gabelle until 1945. Salt making was an important economic activity in many areas of the world. Archaeological evidence indicates that salt was quarried from hills near the Dead Sea before the Bronze Age. At Hallstatt in the eastern Alps of Austria, rock salt was mined as early as 1400 BC. Solar salt was being produced in the northern Yucatan peninsula by the Mayan civilization from about 50 BC to AD 300. Other than the prehistoric use of salt in the southwestern part of the United States by the Native Americans, the first production of salt by American colonists began in June 1614 on Smith's Island, VA, seven years after the founding of the Jamestown colony. The short-lived activity was in response to the high price of salt being charged by ship's captains who brought salt over as ballast from England. Although Nathaniel Loomis is credited with starting the first commercial inland salt production in the United States at Onondaga Lake in New York in 1790, salt had been made by individuals for private use years earlier. Indians had long known of the salt springs in the Kanawha Valley of Virginia (now known as West Virginia). In 1755, Mary Ingles, a white settler, was kidnapped by Indians and was forced to make salt from the saline springs. After her escape, she told other settlers how to make salt. At Saltville, VA, Arthur Campbell began making salt in 1782 by boiling brine obtained from salt springs. In 1799, William King sank a shaft about 3 m in diameter down about 61 m to the underlying Saltville salt deposits. The shaft flooded before he could extract any rock salt; however, King has the distinction of digging the shaft of the first salt mine in the United States. Fig. 1 shows the King site as it appears today in Saltville, VA. Production of brine from the shaft continued until 1892. Settlers moved into the Kanawha Valley in 1785, but it wasn't until 1806 that Elisha Brooks established the first commercial salt works in Kanawha.

Jan 1, 1994

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a longwall installation roadway (faceroad) design methodology that could be utilized by suitably qualified colliery personnel. This goal was achieved in 2012 and the design methodology (and software package) is referred to as Analysis and Design of Faceroad Roof Support (ADFRS). The intended benefits to underground operations, in the provision of this information and resource, are a safer and more productive workplace.

By Emily Sarver, Cigdem Keles, Jonathan Gonzalez, Nishan Pokhrel, Lizeth Jaramillo

This paper presents a case study of respirable dust characterization in a thin-seam coal mine in southern West Virginia. Samples were collected in various locations within the mine and analyzed using scanning electron microscopy with energy-dispersive X-ray (SEM-EDX), thermogravimetric analysis (TGA), and Fourier transform-infrared (FT-IR) spectroscopy. The study found high non-carbonate mineral content, particularly aluminosilicates and silica, in the dust. The results indicate that fine aluminosilicate particles may interfere with SEM-EDX analysis, leading to an underestimation of coal content. The findings highlight the importance of using multiple analytical methods to accurately characterize respirable coal mine dust.

May 5, 2022

By Jean Dupere

Mr. Chairman, Ladies and Gentlemen, I'd like to take just a moment of your time before we examine the current position of the asbestos industry and its market outlook to take a searching look at the product itself. I feel that if we are to understand the problems that beset this basic mining and manufacturing industry and, more important, if we are to appreciate the solutions to these problems that I plan to put forward in a few moments' time, then we had better look at asbestos from the proper perspective. Asbestos has a unique combination of properties - properties not found in any other natural substance or man-made material. This has resulted in asbestos finding its way - in fact, being welcomed - into literally hundreds of applications.

Jan 1, 1984

By Klaus Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300 and 600 °C is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies depending upon structural homogeneity, porosity and gangue quantity. Especially sinters with heterogeneous structures transmit stress to the hematite phase and this favours disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 1, 1981

By Charles T. Holland

The tonnage produced on mechanized automated retreating longwall faces in the United States is growing rapidly. This time last year some 14 faces were operating, and in addition to that, three were known to be down looking towards revision or repairs before being placed back in service. These, it is believed, are now in service. It is estimated at the present time, therefore, that somewhere between 20 and 25 faces are being operated in the country. A survey made last year by the School of Mines, West Virginia University, indicated that longwall mining in general has been beset with a great many problems, some more serious than others. The problems that we propose to discuss here are those pertaining to roof and floor trouble in the tailgates. Longwalls are operating in this country at the present time under an overburden ranging from 200 feet to nearly 3000 feet. Main and tailgate entries are operating in panels of up to five each, with the width of the pillars between these entries varying from 20 to 50 feet. Face lengths are running from 270 feet to 670; actually a face 800 feet long should be possible. The most economical face is often spoken of as being around 450 feet.

Jan 1, 1969

By F. M. Benavides

The mining complex being analyzed consists of four mines and two processing plants located in an area where there are several existing modes of transportation. Figure 1 shows a map of the general layout of the four proposed mines and the two existing processing plants. The mines are identified by the numerals "I" through "IV" and the plants by the letters "A" and "B". A proposed overland conveyor would collect the product from all four mines and convey it to Processing Plant A. Alternate transportation systems are as follows: Railroad transport from Mines I and II to Plant B; Highway trucking from Mines I and II to Plant A; Off-the-road truck haulage from Mine III to Plant B and from Mine IV to Plant A. River transportation from the mines to the processing plants was not considered in this study under the assumption that the high capital investments for the loading and unloading facilities, in addition to difficult traffic problems, would make this mode of transportation unattractive.

Jan 1, 1980

By I. Iwasaki

The effects of autogenous grinding and conventional grinding on the floatabilities of copper-nickel sulfides were investigated as a part of a pilot-plant development project on the differential flotation of Duluth gabbro. At the same mesh-of-grind copper, nickel, and cobalt recoveries were higher and residual sulfur in the flotation tailings was lower with the autogenously-ground pulps. With the ball-mill-ground pulps the residual sulfur in the tailings could not be lowered to the level attained by the autogenously-ground pulps even at increased levels of the collector addition. From mineralogical examinations of concentrate and tailings samples, an electrochemical interaction between grinding media and sulfide minerals was thought to have a greater effect on sulfide mineral flotation behavior than the breakage characteristics of the ore samples in these two types of mills.

Jan 1, 1981

By Peter T. Chiang

A brief literature review on metal separations by ion exchange and solvent extraction of their thiocyanate complexes which are practiced in analytical chemistry as well as in industries was performed. Owing to the poor stability of free thiocyanic acid in acidic aqueous and organic media, technical and environmental problems which cause high thiocyanate consumptions often arise during the practice of the separation processes. This prompted the conducting of a second and more thorough literature review on the chemistry of thiocyanic acid. The objectives of this undertaking are to compile and interpret literature data on the physical properties and chemical reactions of thiocyanic acid, thus providing a clearer understanding of the causes of these problems and giving options as to how to minimize them. The best answer found for carrying out the separation processes is to keep the temperature, thiocyanic acid concentration and total acidity as low as practical.

Jan 1, 1984

By R. Hogg

The sedimentation and dewatering characteristics of flocculated slurries are determined by the size and density of the flocs. Studies of the formation and growth of flocs reveal that floc size is limited by breakage of the agglomerates due to shear in the suspension. Floc density measurements indicate that there is an inverse relationship between size and density. This relationship appears to be determined primarily by the nature of the solid particles, especially the size distribution, but it appears that agitation of the suspension can lead to some densification of the flocs, in addition to breakage. It follows that both size and density can be controlled to a significant extent by regulating the physical conditions (agitation, method of flocculant addition etc.) during flocculation. The use of physical floc conditioning to control the sedimentation and dewatering (filtration) behavior of flocculated, fine-particle suspensions is evaluated in terms of its effects on floc size end density.

Jan 1, 1986

By Rudolf Voigt

Lignite reserves occur all over the world in different climatic regions. This means, that the impact of the hydrologic regime upon mining activities and, vice versa, of the mining activities upon ground and surface water conditions will be different between any two mines. On the other hand, most economically important lignite deposits can be grouped according to principal depositional and structural features described briefly in the following section. These features do allow a preliminary assessments of the nature of ground water problems which may face the mine. The cost of protection against water which threatens a mine, the environmental impact of the appropriate measures to achieve this end and the restraints of population density which both might exclude the most cost-effective approach will govern the project expenditure for drainage work. Whether or not this expenditure can be borne by the project must be established during the feasi¬bility phases of mine planning. So, the somewhat provoking title of this paper does not mean that its question can be answered once for ever. It should rather serve to bring to the attention of the audience the major features of mine water control.

Jan 1, 1985

By Rakesh Sehgal, Pushkar Verma, Mohit Sharma

"SJVN Limited successfully commissioned its Rampur HEP (412 MW) in 2014. The project has been planned to operate in tandem by directly utilizing the Tail Water of SJVN’s prestigious Nathpa Jhakri Hydro Power Station 1500 MW located upstream. The initial filling of voluminous water conductor system of RHEP with 10.50 m diameter, 15 Kilometer long Head Race Tunnel, involved more than 1.5 million m3 of water. The filling operation of such a large diameter tunnel constructed in young folded Himalayas which always offer less ideal sites for tunnelling and their subsequent operations under pressurized conditions is worth sharing with tunnelling fraternity. The paper covers meticulous planning, execution, precautions taken, and performance monitoring during filling process keeping in view the fragile geology, low rock cover zones, shear zones in close vicinity of thickly inhabited areas, squeezing zones, hot water zones encountered during excavation.1.0 RAMPUR HYDRO POWER STATION IN BRIEFRampur Hydroelectric Project (412 MW), is located in Himachal Pradesh (India). This project is a downstream development of Nathpa Jhakri Hydro Power Station (1500 MW) constructed on river Satluj and commissioned during 2003. Both the projects today are now successfully working in tandem. The upstream NJHPS has been constructed on the left bank of the river while the downstream Rampur HPS is located on right bank of the river (Figure-1).The major length of HRT of Rampur project lies on right bank of river before it crosses under the river in its initial reach (Figure-2). The main features of the project are as below:• 10.50 m diameter 15 km long HRT ending in a 155.75 m deep, 38.00 m diameter surge shaft.• 3 steel lined pressure shafts, 5.4 m dia, 211-220m long.• Surface valve house 69 m long x 10.50 m wide x 23 m high housing 3 No. butterfly valves• 3 No. surface penstocks 5.4m dia 368-382m long, bifurcating into six penstocks, each of 3.80 mdia. to feed six generating units of surface power house 158 m long x 24.50 m wide x 48 m high, with Francis turbines each of 68.67 MW capacity."

Jan 1, 2016

By Mark Colwell

As per most other earth science engineering problems, the underground coal geotechnical environment and the way in which roof and rib support interacts with the rock mass are complex issues. While the problem should not be oversimplified (i.e., the dominant failure mechanisms or critical data input parameters should not be ignored), without question judicious simplification is at the heart of all good engineering design. Engineers play a vital role in supplying the world with solutions and products; however it is crucial that engineers make practical and readily useable contributions. One way to ensure this is to employ simplification in the engineering process.

As noted by D.W. Fuerstenau in his Plenary Lecture at the Conference on Extractive Metallurgy of Gold and Base Metals, Kalgoorlie, Australia, "Com¬minution of solids is surely one of the oldest technologies that, even in this day and age of DNAs, chips and space exploration, continues to challenge our scientific acumen and engineering ingenuity." Thus, the fundamentals of comminution continue to receive a great deal of attention in the literature. This was particularly true in 1992 with the publication of the proceedings from the SME-sponsored symposium, Comminution Theory and Practice. Papers covering topics ranging from liberation to comminution fundamentals to novel size reduction techniques are included in this review. Liberation Liberation continued to be a prime area of research interest, not only in terms of liberation modeling, but also in understanding the basic mechanisms involved in mineral liberation. King (Comminution - Theory and Practice, pp. 3-15) described a method for determining the interphase area between mineral grains. He showed how the mea¬surement of interphase area before and after comminution could be used to determine the presence or absence of intergranular fracture. Lin, Miller and Cortes (Kona, Vol. 7) discussed the use of computed tomography (CT) as a nondestructive means of investigating three-dimensional particle composition. The use of this technique in constructing coal washability curves from CT data was presented.

Jan 1, 1993

By Richard C. Corson

The objective of blending materials in a bedding pile is to reduce the variation in successive samples taken from the materials to be blended. In designing a bedding and reclaiming operation, several mechanisms are available to effect the reduction of variability, or increase in homogeneity, of the materials. These mechanisms can act before stacking, in the stacking process, in reclaiming and after reclaiming. In evaluating alternative methods of stacking and reclaiming, the potential user must judge each method on the basis of certain criteria; the capital cost of the equipment, the allowable absolute variability of the reclaimed product and the effectiveness of blending. Several stacking and reclaiming methods have been tested using a computer simulation. Based on the results of this program, factors were developed to describe the effectiveness of blending for chevron stacking of discrete materials and preblended materials, bucket wheel reclaiming and drum reclaiming. From these factors, the total effectiveness of a combined stacking and reclaiming system can be determined.

Jan 1, 1985

By Hans Ruge

The El Soldado copper mineralization occurs as relatively high-grade irregular ore bodies with assay contacts and with frequent inclusions of barren rock. The sampling method must be timely for production grade control purposes, as well as accurate and inexpensive. Sampling techniques evolved from sampling dump cars at the haulage level to sampling scooptrams at the loading pockets. These were abandoned in favor of sampling production blast holes. Several sampling alternatives are discussed. These involve the selection of optimum volumes and sampling frequencies while taking into consideration geological parameters and statistical analyses of sampling data.

Jan 1, 1984

By Jean-Michel Rendu

In most mining operations, some degree of selectivity is applied. Whether one deals with surface or underground operation, ore zones, and waste zones are defined not only on the basis of the value of the ore contained, but also taking mining constraints into account. A number of computer techniques are presented which can be used to determine the optimum location of the footwall and hanging wall of ore zones intersected by drill holes. Minimum mining width and minimum internal waste width constraints are taken into account, as well as other economic constraints. The system is presented as an integral part of a larger manumatic ore reserve and mine planning system.

Jan 1, 1982

Sandvik built its first stone crusher in 1896 and has since grown to become a world leader in mining equipment. ?We are the best in the world, and we can now be even better at making our cone and jaw crushers in different models,? Olle Lundberg, production engineer at the Sandvik Mining factory in Svedala, Sweden told freelance journalist U. Samuelsson, of mekpoint.com. As a specialty manufacturing business under the umbrella of the Sandvik Group, Sandvik Mining is a leading global supplier of equipment, tools, services and technical solutions for the mining industry. Its expertise covers the areas of rock drilling, cutting and crushing, as well as loading, hauling and the handling of materials. Lundberg, along with five colleagues, will write CNC programs for the lathes and machining centers that manufacture Sandvik?s specially constructed casting. In 1999, Sandvik chose ESPRIT computer-aided-manufacturing (CAM) software by DP Technology to program its array of machine tools, and has worked with ESPRIT reseller Holotech, based in Örebro, since 2003.

Jan 1, 2014

By D. L. Moellenberg

Under various state laws enacted mostly within the last 20 years, reclamation requirements and standards for hard-rock mining operations have been established virtually everywhere in the western United States. Unlike the uniform and detailed coal mine reclamation requirements under the federal Surface Mining Control and Reclamation Act ( "SMCRA" ) and state programs mode led after SMCRA, the various state law hard-rock mine reclamation requirements are based upon a variety of objectives, and therefore are subject to varying standards from state to state. While the diversity of reclamation requirements complicates the determination of what reclamation measures will be required at any particular mine, there are valid reasons for this diversity. There are dozens of different commodities mined in the United States, and mining methods are different for each commodity. Local natural conditions such as climate, precipitation, geology, hydrology, and biology vary widely across the county. Site-specific conditions also affect mining and reclamation methods. Also, factors such as economics, land use, and environmental protection issues receive different priorities in different states and communities within those states. State reclamation requirements in general provide the flexibility to consider site-specific circumstances, allowing operators to design and engineer the best reclamation measures for each mining site. To the mine developer or manager, reclamation requirements must be translated into design, operational, and closure measures for mine planning. Each of these measures must then be assigned additional costs to be factored into the economic decisions for a particular mining operation. On a broader level, reclamation costs must be factored into decisions such as where to invest in exploration and mine development. The purpose of this paper is to provide a summary of the state non-coal mine reclamation requirements in twelve western states. This summary comparison may be useful as a starting point in considering how local reclamation requirements will impact potential mining costs.

Jan 1, 1994

By Stephen Meyer, Véronique Falmagne, Antti Pyy

Kittilä Mine is a gold mine located in Northern Finland, owned and operated by Agnico Eagle Finland. The mining operation started in 2008 with open pits which were completed in 2012 and production moved to being entirely underground. The mine consists of four separate orebodies, currently producing 2.0 Mt per annum, and requiring over 19 km of development on a yearly basis. The principal mining method is long hole stoping with delayed backfill. Microseismic monitoring was initially tested in the Suuri orebody, in the mining block between the 625 and 500 Levels. A small monitoring system was installed in 2018, after observations of stress-induced damage to the rock mass and in anticipation of future mining at greater depth. The initial goals were to evaluate if useful data could be recorded and test the signal quality of different sensor types. Prior to 2018, ground control related challenges in the Suuri and Roura mining blocks had been mostly related to sill pillar mining and block movements between weak graphitic schist planes. Seismic monitoring in the Suuri deposit proved successful for following the rock mass response to mining and helped support the rationale for early monitoring in the new, deeper mining block in Rimpi at 900 m depth. Preliminary geotechnical characterization and testing of the rock mass showed areas of silicification in the footwall rocks with potentially continuous structural features. Seismic monitoring of the Rimpi area has confirmed the brittle behavior of the rock mass, with strong seismic responses induced by stress changes following blasting being recorded. In addition to this expected behavior, a large magnitude event associated with significant damage in the footwall drive development 90 m above the stoping was experienced. Initial investigation of the rockburst showed two separate damage locations with over 300 tons of displaced rock. The seismic monitoring system recorded this rockburst as a single seismic event with magnitude significantly larger than previously recorded. Additional analyses indicated a possible thrust fault event, triggering two separate strainbursts. Following this event, the ground support system was upgraded in parts of the footwall drives to improve dynamic capacity. Systematic calculation of the source mechanisms for the small footwall events down to Mw-2.5 has revealed potential planar structures in the footwall. Early implementation of microseismic

Apr 26, 2022