Search Documents

By F. Letowski

A column reactor was applied for leaching with simultaneous flotation a complex sulfide ore in ferric sulfate-solution under oxygen pressure. Elemental sulfur and the flotable, nonreacted sulfides were collected in the froth and separated from the insoluble, nonflotable gangue minerals and solid particles formed during pressure leaching. The two-stage laboratory unit, built from Corning-glass elements is described. Results of the continuous leaching/flotation experiments conducted under 20-40 psig of oxygen pressure are presented, as are supplementary batch leaching experiments with iron precipitation under 150 psig oxygen pressure. High zinc extraction to solution and near total accumulation of lead sulfate in the nonflotable fraction are easily attainable. Relatively poor flotation of pyrite is probably caused by the partial oxidation of its sulfidic sulfur to sulfate.

Jan 1, 1988

By D. R. Lanners

Samples of the same coal measure overburden spoil were obtained from three different mine sites. Site A used a 27-m3 tub-mounted dragline, Site S used a front-end loader and truck combination, and Site C used a 6-m3 crawler-mounted dragline. The spoils were analyzed in the laboratory for the strength parameters using drained triaxial tests conducted on 150-mm diameter specimens. Regression analysis was utilized to determine the appropriate failure criterion for the strength data from each site. Spoil obtained from Site S yielded higher shear strengths than Sites A and C.

Jan 1, 1993

By Paul L. Boni

Trona, Na3(CO3)(HCO3) ? 2H20, is mined in quantity from saline facies of the Eocene Green River Formation of southwestern Wyoming. The Green River deposits are the world's largest known resource of natural sodium carbonates. An estimated 127 billion tons of trona ore are known to occur in beds exceeding 4 ft in thickness (Wiig and others, 1995). Twenty-five trona beds, exceeding 3 ft in thickness, and covering at least 100 mil have been identified. The beds are numbered sequentially in ascending stratigraphic order. Trona beds underlie more than 850 mil (bed 17) and are up to 37 ft thick (bed 1) (Culbertson, 1966). Five underground mines, operating in beds 17, 19, 20, 24, and 25, process trona to produce soda ash (sodium carbonate). A total of 11,837,703 short tons of soda ash were produced from 17.1 million tons of trona ore in 1997 (Kostick and Clark, 1998). A detailed study of trona bed 17, using techniques of petrography and X-ray diffraction, has been undertaken in the Solvay trona mine, near Green River, Wyoming. A continuous, vertical-channel sample was taken from near the production shaft for this study. At this location, bed 17 is 12.6 ft thick and includes several stratigraphic markers that are easily correlated throughout the mine and in surrounding drill cores. Bed 17 in this area averages 90% trona through its entire thickness (Wiig and others, 1995) and 95-100% trona in the lower two-thirds of the bed. Mineral impurities include water-insoluble dolomite, quartz, pyrite, clays, and other minerals and partially water-soluble northupite and shortite. Northupite, Na3Mg(CO3)2C1, contributes to chloride contamination in the soda-ash product and is concentrated in the upper one-third of bed 17, which is left behind as roof rock. Northupite has two modes of occurrence: (1) as bedded strata with dolomite, chert, clay, and shortite and (2) between primary trona crystals in trona spar. Petrographic and mineralogic data indicate that this section of bed 17 was deposited subaqueously during its early and late history and may have undergone periods of deposition in a subaerial or marshy environment. Stratigraphic data indicate that trona accumulated at an annual rate of 2-4 in. per year. During trona deposition, dolomite, CaMg(C03)2, precipitated in parting layers when new water entered the lake, freshening supplies of calcium and magnesium. The lack of clay minerals in the trona facies suggests water input may be by means of springs, as opposed to overland flow. Clay occurrences in thicker dolomitic partings within the trona facies indicate periods of episodic overland flow, possibly resulting from storms in the surrounding basin.

Jan 1, 1999

By J. R. Schafler, J. L. Brinkman

"The US coal mining industry has suffered a recent decline in profits caused by a combination of decline in commodity demand and more restrictive government regulation, forcing coal mining companies to cease production in numerous mines. A 40% decrease in the total number of coal mines occurred from 1994 to 2000. The number of mines remained relatively constant until 2008 when a change of government sparked a series of new environmental regulations which have contributed to another 15% decrease from 2008 to 2016. In contrast, production has only decreased by 3%, increasing from 1994 to 2008, and then decreasing since 2008. However, this value is skewed by large increases in sub-bituminous coal production and decreases in other coal ranks. Several aspects assist in executive decisions on mine longevity and economic worth. Studies of open source mine data collected by mandated government surveys coupled with commodity history can be used to find relationships between mine closures and these elements, which include statistics on production tonnage, seam height, coal rank, etc. This paper looks at coal mining trends since 1994 by comparing mine, market, and regulation factors that may influence mine closure. INTRODUCTION The US coal mining industry is currently experiencing a decline in both demand and commodity price while facing implementation of more stringent air and water pollution regulations. Company profits have decreased significantly, forcing several major companies to declare bankruptcy. The industry was required to adapt to survive. Many of these companies have adjusted by abandoning mines; the last two decades have seen a drastic decrease in the number of mines. To discover the primary causes of this downturn, three major aspects must be studied: properties of abandoned mines, commodity history, and regulatory impact. TRENDS SINCE 1994 Each year, US coal mines are required to submit data on a wide variety of categories to the Mine Safety and Health Administration (MSHA) and the US Energy Information Administration (EIA). This data includes administrative records, production values, and information regarding the attributes of the mined material and the mine itself. Each year since 1996, EIA has released a report summarizing the data from two years prior. Additionally, MSHA maintains a database containing a collection of all the most current data. These resources are the primary sources for the following figures."

Jan 1, 2017

By Gilbert A. Bonforte, Hugh P. Caspe, Tracy K. Lundin

The Narragansett Bay Commission (NBC) Combined Sewer Overflow Abatement Program is a major effort to address and mitigate discharges from combined sewer overflows in the Providence, Rhode Island area. The proposed system consists of three deep rock tunnel segments totaling 17.8 km (11.1 miles) in length that will provide 860,000 cu m (227 million gal) of storage at depths up to 99m (325 ft). This paper discusses 13.5 km (8.4 miles) of 6.64m (21.8 ft) finished diameter tunnel, four construction shafts, 19 dropshafts and one large diameter pump station shaft tapered from 1 5.2m (50 ft) at the surface to 27.4m (90 ft) at depth. All facilities are in preliminary design.

Jan 1, 1995

By H. Ankara

Determining the identicalness levels of the same model trucks working in open pit mine transportation system by means of statistical analysis methods is very significant in terms of availability analysis. In this study, the identicalness levels of two trucks picked randomly from the 170-short-tonne truck fleet working in open pit coal mine over one-year period were examined through a non-parametric test, Mann-Whitney U test for two samples. Time to failures (TTFs) and Time to Repairs (TTRs) of the trucks were analyzed with this test technique and then whether they were identical or not was determined. In order to determine whether the trucks identified to be identical at the end of this test displayed the same mining performances within the same open pit transportation system, the availability analysis of the identical trucks was carried out. As a result of the availability analysis, it was observed that the trucks had availability values that were very close to each other. It was also determined that Mann-Whitney U test could be employed together with availability analysis. Finally, it was observed that Mann-Whitney U test for two samples could yield rapid results in the performance analysis of complex systems like open pit mines.

Jan 1, 2010

By Roger Holmberg

INTRODUCTION The driving of drifts is a very important aspect of underground mining. It is not unusual for the percent¬age of rock broken during development in a mine using sublevel caving, for example, to be as much as 25% of the total. If one also considers the amount broken for transport, ventilation, and exploration drifts, one can easily understand that the planning and excavation of drifts play a major part in the total economics of the mine (Fig. 1). Increasing mechanization in mining demands larger tunnel areas for transport and mining equipment. With modern machines the hard work involved in using hand¬held pushers is gone, and a better environment is achieved. More rational methods could be used, but much of the experience the working man acquired by working close to the rock face (such as utilizing the natural weak planes in the rock when he placed the drill¬ing holes) has unfortunately been lost. By having sepa¬rate shifts for drilling, loading, and hauling, more atten¬tion has to be placed upon a well-designed drilling pattern. Some reduction in the number of holes required can be achieved with mechanized drilling because of the larger holes that can be produced. On the other hand, it is probably not possible to achieve the same precision as with pneumatic pushers, and it is difficult to utilize the larger holes because these cause more damage to the re¬maining rock. Recently, however, the precision has be¬come very good with the parallel booms and automatic devices for setting the lookout angle (Fig. 2). A larger arch of the drift roof requires a more carefully executed blasting procedure than before in order to prevent rock fall and to insure a sufficiently long stand-up time. In this chapter, empirical relationships that can be used to design an economic and optimal drift blasting design will be presented. The principles of the calcula¬tion method are based upon the earlier work of Langefors and Kihlström (1963) and Gustafsson (1973). COMPARISON OF EXPLOSIVES To provide for the use of various explosives it is necessary to have a basis of comparison. Several meth¬ods have been developed to characterize the strength of an explosive. Some examples are comparison of values given by (1) calculated explosion energies; (2) the ballistic mortar test; (3) the Trauzl lead block test; (4) the brisance test; (5) the weight strength concept; and (6) the underwater test. However, most of these meth¬ods should be used carefully when stating the breaking

Jan 1, 1982

By K. Kim, T. M. Yegulalp

A new explanation of the scale dependency of rock strength is presented based on the theory of extremes. A brief review of past work on specimen size and strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect. It is shown that the weakest link theory is directly related to extremal statistics and that parameters of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1994

By Albert W. Deurbrouck

The coal reserves in the United States are estimated to be in excess of 300 billion recoverable tons, and current projections of energy requirements indicate our increased dependence upon these reserves. The Department of Energy's Energy Outlook for 1984 projects that coal consumption in the United States will increase from 737 million tons in 1983 to 958 million tons in 1990, and then to 1,110 million tons in 1995 (Table 1). As shown in this table, the future utilization of coal in the United States is closely tied to the electric utility market, a market that consumes about 85% of the coal produced. Be- cause of this dependence on the utility market, the uncertainties of new environmental regulations, particularly those concerning sulfur emissions, could have a significant adverse impact on future coal demands in the United States. SULFUR IN U.S. COALS Most of the Nation's coal reserves contain too much sulfur to be fired directly and meet existing emission control standards. In Table 2, the sulfur contents of the coals of the eastern United States are summarized by sulfur levels according to regions. While the coals of some of the eastern regions are predominantly high in sulfur content, it is important to recognize that large tonnages of coal with relatively lower sulfur content are available in these regions. Furthermore, an often significant portion of the sulfur occurs in the form of iron sulfide (Fes2 or pyrite). Because pyrite occurs as discrete particles of high specific gravity, it can often be removed by simple, inexpensive physical coal beneficiation techniques after being liberated by stage crushing. The potential for physical removal of pyrite by conventional specific gravity processes combined with stage crushing is summarized in Table 3 on a regional basis.

Jan 1, 1986

By Scott W. Harrison, Richard E. Aaseng

In 1993 Ispat Inland Mining Company began mining its Laurentian ore reserve, which has six distinct ore types that are extremely variable. Initially batch processing was necessary to optimize mining equipment utilization. The variability as found in the ground was compensated for in plant operation, which proved ineffective. When the last of the six ore types was introduced in 1997, production, quality, and cost were seriously impacted. In-pit blending was the solution developed by the process management team to provide the plant feed required to economically process all six ore types in the Laurentian reserve.

Jan 1, 2000

By Thomas R. Hightower

The Thunderbird plant was erected in Sullivan County in Indiana during 1958-1959. It was first put in operation in March of 1959. At the present time the source of the raw coal is from the Indiana No. 6 seam. The underground operation at present consists of two continuous mining units and two conventional units. The underground is all belt haulage and the first unit with which this paper is concerned is the slope belt. It is a 48-inch-wide inclined belt with 980-foot centers and a lift of 275 feet. The belt is powered with a 350 H, P, motor and has a rated capacity of 600 Tons per Hour. The belt is equipped with a Merrick Scale Company Weightometer, The raw coal moves from the belt to a 6'x12' extra heavy Allis-Chalmers Ripl-Flo equipped with 6" round-hole screens. The over product of the screen is fed into a 10'x20' long McNally- Pittsburg rotary breaker equipped with 4-l/2" round-hole screens. The oversize rock is discharged into a bin that is emptied with a refuse truck. The through-product of the breaker, along with the through-product of the Ripl-Flo, passes either directly to the McNally Giant washbox or to a 36" belt that transports it to a 1000-ton storage bin,' The change from either to the washbox or to the storage bin is made by use of a motorized gate controlled by the plant operator,

Jan 1, 1961

By W. Nazarewicz

The introduction of continuous papermaking in the early 1800's was the beginning of the industry as we know it today. Since that time, the majority of the paper produced has employed an acid process. However, in the mid 1960?s, European producers began a transition to an alkaline papermaking process. Early European mill conversions to alkaline papermaking begun in the 601s, accelerated during the 1970's influenced by the dramatically higher cost for OPEC energy as well as the high cost of fiber and imported filler clay.

Jan 1, 1986

By Shawn T. Sorrell

Phillips Coal Company (PCC) submitted the first surface mine permit application under the Office of Surface &lining approved regulatory program of the State of Louisiana. This application for the Oxbow Lignite Surface Mine which is located approximately 64 kilometers (40 miles) southeast of Shreveport, Louisiana was submitted in March 1981. The State of Louisiana Office of Conservation, Surface Mining Division, assigned this application number LSM-1, indicating it is the first one submitted in Louisiana history. The permit area for the Oxbow Mine encompasses 6,251 hectares (15,627 acres). Of this total permit area, 5,862 hectares (14,656 acres) were classified by soil type as prime farmland by the U.S. Soil Conservation Service (SCS). Prime farmland acreage in the permit area became a major central issue in our early planning stages and throughout the permitting process of the Oxbow Mine, due to the magnitude of acreage involved.

Jan 1, 1982

By R. K. Agarwal

In this paper a simple three-layered medium is considered. A circular hole is centrally located in the intermediate layer. The layered sheet is loaded uniaxially perpendicular to the stratification. The Young's modulus of the intermediate layer is lower than that of the outer layers. The stress distribution around the circular hole in a stratified medium is significantly different when compared to the case of a continuous homogeneous medium. The distribution depends upon the ratio of the height of [the] intermediate layer and [the] hole diameter. A comparison of stress the distribution and procedures for preparation and testing of [the] model are given. The potential of the technique is outlined.

Jan 1, 1968

By B. L. Bessinger

Because of a, work stoppage at the Carlsbad plant, IMC faced the challenge of operating a 24-hour-a-day mine and plant with inexperienced maintenance and production crews. This is an underground mining operation, using the room-and-pillar mining- method. The mine was entirely, mechanized with conventional equipment, was hoisting an average of 13,539 tons off ore per 24 hours, and employed a, mine maintenance group of 100 men. The 100-man, mine maintenance group was equally divided between mechanics and electricians. In re-forming this maintenance group, two main objectives were to be achieved (1) a general upgrading off the intelligence level; and (2) the elimination of craft lines for greater flexibility.

Jan 1, 1966

By J. R. Henke

Dewatering wells producing iron-rich water experience rapid declines in yield and drawdown due to the formation of ferric (Fe +) hydroxide deposits in well screen, pump intake and riser pipe. Precipitation is caused by a combination of dewatering-promoted iron oxidation and iron-oxidizing bacteria. Physical and chemical well rehabilitation techniques, as well as alternative well construction and well development techniques designed to minimize well clogging, were evaluated in this study. The addition of acid downhole feed systems to dewatering wells prone to iron encrustation can, in some cases, prolong their operational lives up to 500 percent that of unacidified wells.

Jan 1, 1989

By Thomas E. Shufflebarger

Definition of glass sand prospects may be modified by constraints which range from demography to critically important product-control. Characteristics of usable raw materials, physical and chemical, are discussed; an ideal raw material is defined. Following field investigations and preliminary sampling, evaluation of selected prospects includes use of modern drilling techniques, viz.: core, percussion (air-hammer), auger, jet, rotary jet, split-spoon and other. Nearly complete core (sample) return is mandatory. Land-use regulations, availability of water and transportation continue to direct exploration in a major sense. But fitting a prospect to burdensome politics nay be considered a decidedly negative factor.

Jan 1, 1983

By Ralph E. Magnuson

The quality of our environment is of great importance to all of us. Today, there is a great public concern about the degradation of our air, land, and water and the resultant slow death of our planet Earth. The miner has always been concerned with his environment. Historically, mining has been a part of the frontier. As a result, the miner has pioneered and developed many parts of the world. In the beginning, he had to hack out a place for his mine, himself, and his family. He was given accolades and praise for his accomplishments. Now, however, he is attacked as a ravager of the landscape. It was and is no different on the Marquette Iron Range in Marquette County, located in the Upper Peninsula of Michigan. Iron ore was discovered in 1845 and mining was begun by 1848. Over nearly 1 ¼ centuries, a total of 379,197,000 tons have been shipped to market. Ports, docks, railroads, and towns all had to be built in order to get that tonnage out to iron and steel makers. In those early days the environment had to be mastered, not pampered.

Jan 1, 1970

If a fire occurs outby an underground coal mine section, the immediate safe evacuation of miners from the working section should always be the first action during the rescue operation. Unfortunately, in many cases, the escape-ways (escape routes) dedicated for miners' evacuation are contaminated with fire byproducts from adjacent entries. The purpose of this paper is to present the ventilation control process that will maintain the escape-way free from contaminants and available for travel. Several scenarios in a different section on ventilation system arrangements are analyzed, discussed and presented. To perform these studies, the author used a mine-fire simulator, which provides a dynamic (in real time) representation of the fire's progress and also gives a display, a color-graphic visualization, of the spread of combustion products throughout the ventilation system. Presented and discussed in this paper, also, are ways in which the mine-fire simulator can be used as a training and teaching tool for miners and, particularly, for ventilation and safety personnel.

Jan 1, 1993

By T. A. Lloyd

The use of tank cells over the years has provided a means for low cost, space efficient, extra capacity in existing flotation circuits. In some cases, new plants have selected tank cells as the machine of choice. Typical tank cells use high efficiency impellers for mixing, which results in low power draw. Unfortunately, these mixers have poor aerating characteristics that compromise metallurgical performance. This has all changed with Outokumpu's new flotation concepts. Outokumpu has recently developed the HG or High Grade flotation cell that can provide higher recovery with better selectivity while maintaining the simple operation of conventional cells.

Jan 1, 1993