Search Documents

By B. DANIEL MARJAVAARA, I. A. SOFIA LARSSON, ANNA-LENA LJUNG

One way to upgrade iron ore is to process it into pellets. The pelletizing process is multifaceted, involving complex fluid dynamics with highly turbulent, high-temperature flow in intricate geometries. This makes it hard to perform measurements during operation, so a useful tool for better process understanding is computational fluid dynamics (CFD), where the challenge is to perform efficient and trustful simulations of complicated problems. A validated simulation model can be valuable for increased process control and development. In this paper, the flow field and coal combustion process in a pilot-scale iron-ore pelletizing kiln is simulated using a CFD model. The objective of this work is to apply a coal combustion model to enable an investigation of thermal effects from the flame on the surrounding flow field.

By Mogens Henriksen

In the past decade, numerous urge scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in Figure 1. Allen1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs2. His data, however, do not reflect sensitivity of flowrate to air/water ratio. Further, in Gibbs' work, air apparently is injected continuously along the column of water. This configuration differs from that used in reverse air lift drilling where air is injected at discrete points only. Gas lift theory has received considerable attention over the past decades. Orldszewski3 defined flow regimes in two phase flow. Griffith and Wallis4 determined relative velocities of gas to liquid. Two-phase flow has been studied extensively for oil transport in inclined and vertical pipes by Chierici et a15, Beggs and Brill6, and Gould, Tek and Katz.7

Jan 1, 1977

By T. H. Jones

Fall of ground is a leading source of worker injury and fatality indicating a persistent need for ground monitoring technology. The HRTMM is an experimental convergence monitor utilizing a digital camera and custom software to track the position of one or more lasers across the target. Apparent laser movement is proportional to target convergence. The HRTMM was installed in an underground mine near active operations to test its response to the mining environment. This included intense blasting vibration and mine fog. Results and potential of the new monitoring technology will be discussed.

Jan 1, 2008

By R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al (III) and flotation collectors. It was found that the presence of Al (III) is necessary for good flotation of the organism whether or not Pb(II) is present when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8 and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al (III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminoproprionic acid is used as collector good flotation occurs at about pH 4 without the addition of Al (III).

Jan 1, 1990

By R. Addison

Boom, boom, boom, boom. The staccato beat rings out across the bush; the stamps are at work - slowly pulverizing gold-bearing ore for a patient, grizzled prospector. This is the State Battery near Marvel Loch - a tiny (capacity: 25 ton/day) gold plant operated by the Western Australian government. It is one of many such plants located in remote corners of Western Australia and the Northern Territory - miniature custom mills operated for the benefit of prospectors and small mine operators. These State Batteries, so called because they are operated by state governments and because the principal item of machinery in the plants are stamp batteries, are fascinating anachronisms: throwbacks to times long past, to a century ago, to the hard and heady existence of gold rush days.

Jan 1, 1986

By Robert M. Cox

Systematic roof bolting has proven to be a very effective method of mine roof control; however, major roof failures still occur and roof falls still remain the number one occupational hazard of underground miners. Why do some bolted mine roofs fail, while the vast majority of bolted mine roof remains stable and safe to work under? Observations of numerous roof failures indicate that most of the major roof failures* are associated with either: 1) Jointing, faulting or other structural fracture zones; 2) massive shale beds of lenticular structure, or 3) thinly laminated sand-shales. The jointing and faulting present an obvious weakness in the roof rock structure; whereas, the massive shales and laminated sandy-shales create a roof structure with low shear strength and/or modulus of deformation. An observation of major significance is that most bolted mine roofs fail as a unit, and that the thickness of the fall is roughly equivalent to the roof bolt length (See Figure 1). In fact, several operators have experienced the phenomenon of an increase in roof fall thickness with an increase in roof bolt length.

Jan 1, 1973

By Bennett D. Lass

A new method for determination of residual flotation oils on beneficiated kaolin clays has been developed. The method, which yields qualitative information, is based on fluorescence measurements employing a spatially resolved, polychromatic illumination source for excitation, and a two-dimensional detection scheme using a silicon-intensified, video imaging device. The method was used to identify residual oils on a beneficiated, Washington County, Georgia, crude clay. The results were compared to a similar qualitative analysis performed via capillary column gas chromatography using an FID detector. The video fluorometry was the preferred method of, analysis.

Jan 1, 1983

By Larry Sevenker

On the basis of favorable salt characteristics, primarily compressive strength and impermeability, solution-mined cavities can provide structurally stable isolation chambers for waste. Solution mining techniques are established for storage of hydrocarbons. The proposition of waste isolation in engineered salt cavities is similar to this practice relative to characterization, certification and safeguards. What materials are isolated and how operations are conducted are principle differences. Compatibility of wastes with other wastes must be considered, but hazards can be precluded by avoiding certain mixtures. Waste material characteristics and cavity considerations are discussed.

Jan 1, 1981

By Takaji Kusakawa

In Japan, almost no natural gypsum is mined for industrial uses of gypsum, and almost all gypsum is synthetic gypsum, that is desulphogypsum, produced by waste sulphur dioxide gas from metal smelters and power plants, and other industrial waste sources. The amount of such sythetic gypsum production has reached more than six million metric tons per year (1979). Major uses are for cements and building materials. Other uses are soil conditioner, investment casting mold, organic composite materials, etc and sulphur recovery by gypsum decomposition is being examined. This paper summarizes present Japanese production and uses of sythetic gypsun produced from industrial waste.

Jan 1, 1982

By L. L. Anderson

Western bituminous coal can be processed to low sulfur liquid fuels by fast reactions. A process (LEFCO) under development at the University of Utah uses coal and catalyst under hydrogen pressure to convert 60 to 70 percent of the coal matter to fuel liquids and gases. Coals have been processed in small diameter (less than 1/2 inch) tubes and at reaction residence times of less than 10 seconds. Effects of process variables on the yield and quality of products have been studied. General features of the process and the properties and characteristics of the products produced are presented. Special features of the process that distinguish it from other liquefaction processes under development are also discussed.

Jan 1, 1975

By Joe B. Rosenbaum

Waste solutions from sea water desalination processes are enriched in minerals by a factor of two or three. This suggests that extraction of selected mineral components from the concentrated brine might help pay desalination costs. The possible recovery of gold has received particular mention. Sonstadt, in 1872, reported the gold content of sea water as 65,000 micrograms per cubic meter, or 65,000 parts per trillion. At $35 an ounce, this is equivalent to $0.065 per ton of sea water. Fritz Haber, however, after his abortive venture to restore Post War I Germany to economic health by recovering gold from the sea, concluded the gold content was 4 micrograms per cubic meter. Haber's analysis is equivalent to 0.0004 cent per ton. In the past 10 years, investigators using advanced analytical techniques reported from 4 to 27 micrograms per cubic meter. Our brief experiments to determine a threshhold value for the gold in sea water employed solvent extraction for initial concentration, evaporation of the gold-loaded organic for further concentration, and atomic absorption analysis of the gold in the concentrated organic. Radioactive gold was used as a tracer for monitoring the gold through the concentration and analytical steps. Our method established that sea water contains about 11 parts gold per trillion parts sea water, or 0.001 cent worth per ton. This agrees closely with results of recent studies by other investigators employing ion exchange resins and neutron activation techniques.

Jan 1, 1969

By Donald Towse

Portland cement is a basic building material in every country in the world, and, fortunately, the raw materials required in its manufacture are widely distributed. It is a low-priced bulk commodity (price one cent a pound or less, with a density of 100 pounds per cubic foot.) Table 1. Approximate price per pound of selected mineral products. Copper 48 cents per pound Aluminum 27 Lead and zinc 15 Asbestos 3 to 18 Pumice 6 Sulfur 2 Bauxite (abrasive) 1.8 Barite 1 to 1.6 Cement 1 Primitive regions may get along without any Portland cement, but most countries use some, and it is one of the most widespread building materials, even if used in small quantities. Use of cement begins early in a country's development, and, because of local availability of raw materials, cement manufacture is one of the first heavy industries many countries desire. Use and manufacture of cement usually precedes other industrial materials such as steel and heavy chemicals, and consumption levels off for a long period during development of infrastructure and an economic base. With a mature economy comes a very high consumption. Per capita consumption varies ten times or more between nations (Figure 1).

Jan 1, 1970

By W. Wan

Diesel particulate matter (DPM) emitted from diesel engines is currently considered to be a health problem in underground mines. As a result, attempts have been made to control DPM both by reducing emission rates and by managing the DPM that gets into the mine atmosphere. This paper presents a method for modeling the generation, transfer and distribution of DPM in the mining sections through the use of a convection-based computer model so that controls for emitted DPM can be evaluated. A variety of ventilation strategies and diesel deployment schemes for room-and-pillar development sections were simulated to compare their effects on average DPM concentrations at several fixed and mobile personnel locations in the section. Input data for the model was gathered from actual diesel development sections and derived from experimental study results provided by other researchers. Studied using the model were ventilation schemes using vent tubing and brattice, exhaust location strategies on the vehicles, and the direction of ventilation at the feeder-breaker location. A summary of results from this study will be presented.

Jan 1, 1994

By Chulho C. Song, Liam Coleman

Alkaline pressure oxidation (POX) is an oxidative pre-treatment option that is commercially used for high-carbonate sulfidic gold ores. The high carbonate grades within the feed ore shifts the ideal operating pH to a basic regime. Compared with acidic POX, alkaline POX typically requires additional steam input due to a lower sulfur oxidation load and a high rate of in-situ carbon dioxide generation that needs to be vented along with steam. The cost of this steam addition is the largest differentiator between acid POX operation and alkaline POX from a cost comparison. However, alkaline POX can offset these costs through reduced acid usage for pre-acidulation and decreased alkali reagent consumption for subsequent neutralization. This paper reviews the specific operating cost impacts of acid/base consumption between alkaline and acidic POX with ores which require pre-acidulation, the overall economics of alkaline POX, and the regimes in which alkaline POX is economically favorable. The findings aim to guide industry professionals in making informed decisions for alkaline POX adoption by providing a summary view of its operational benefits and costs, contributing to the development of cost-effective and sustainable gold ore processing techniques.

Feb 1, 2025

By Joel L. Morrison

Wet bituminous coal fines from active and abandoned slurry impoundments are currently being examined as a recoverable feedstock for the production of coal water slurry fuel (CWSF). Preliminary analysis indicates that these coal fines can be converted into low solids, low viscosity CWSF with acceptable stability without the use of viscosity modifiers (dispersants) or stabilizers. Efforts are now underway to determine if the impounded coal fines can be economically cleaned by froth flotation to an ash level of < 12 wt. % and a total sulfur content of 1.2 wt. %.

Jan 1, 1995

By S. Chander

The mechanism of oxidation of sulfur in pyrite is a function of the rate and driving force for oxidation. New evidence is presented in this article to show that at moderate potentials, a sulfur-rich hydrophobic layer is formed. Under ordinary conditions, the sulfur layer is covered with a layer of iron oxides, hydroxides, sulfate or oxy-sulfide ions. Under these conditions, pyrite is hydrophilic. In the presence of iron-chelating agents or iron sequestering ions, iron layer might not form. Under these conditions, sulfur-layer is exposed and pyritic might become hydrophobic. Stronger oxidizing conditions decompose the sulfur-layer, thereby making the surface hydrophilic.

Jan 1, 1992

By C. A. Young

Previous experimental results have shown that an increase in temperature and/or oxygen concentration leads to an increase in the hydrophobicity of fluorite (CaF2) with adsorbed oleate. Subsequently, ex-situ Fourier transform infrared (FT-IR) transmission studies suggested that this increase in hydrophobicity was the result of double-bond reactions between adjacent oleate species adsorbed at the fluorite surface. Now an in-situ FT-IR study on single crystals of fluorite has been used to monitor this phenomenon using internal reflection spectroscopy (IRS) with the crystals serving as reactive internal reflection elements. The double-bond reaction has been correlated with in-situ adsorption density measurements. These results demonstrate that only the first chemisorbed oleate layer undergoes the double-bond reaction at an appreciable rate. However, multilayers of precipitated calcium oleate in the case of fluorite appear to react minimally even for oxygen saturated solutions at elevated temperatures.

Jan 1, 1991

The adsorption of gold onto activated carbon in iodide solutions has been studied. The adsorption rates were determined as a function of temperature, salt concentration and pH as well as activated carbon concentration. A kinetic model was also developed for the adsorption. The adsorption rate was believed to be controlled by a mixed mechanism of film diffusion and pore diffusion, but the film diffusion had a major contribution to the overall rate. Experimental findings were in good agreement with the model developed. The apparent activation energy was found to be 14.9 kJ/mol.

Jan 1, 1993

By J. J. Kellar

Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available which allow direct in-situ analysis of adsorbed layers. Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IRJIRS) with reactive internal reflection elements allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in-situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar, 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Figure 1 is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/ dodecyl sulfate, CaCO3/oleate, ZnS/xanthate, and KCl/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990).

Jan 1, 1992

By S. B. Castor

Although production generally satisfies demand for rare earths, new markets may make undeveloped resources, particularly those rich in yttrium, more interesting. A Precambrian carbonalite orebody at Mountain Pass, California, has been the world&apos;s largest rare earth producer. Minor rare earth production comes from titanium placer mining in Florida and uranium mining in Canada. Prior to operations at Mountain Pass, North American production was mostly from placer deposits that constitute large, low-grade rare earth resources. Newly discovered North American rare metal resources in peralkaline igneous rocks are potential yttrium producers. Most of these resources are in a continent-wide belt of anorogenic magmatic rocks approximately coeval with mineralization at Mountain Pass. Other untapped rare each resources in North America are generally light rare earth-dominated and small or of low grade.

Jan 1, 1991