Search Documents

By L. W. Saperstein

One of the most critical skills developed by underground coal miners is the ability to interpret natural warning signals in terms of impending roof failure. A miner receives a variety of signals which can be called warning and which can be classed broadly by sense: aural, visual, and tactile. This paper concentrates on those signals which are airborne and audible. These signals are creaks, cracks, pops, groans, snaps, booms, tears, rips, and other assorted pulses which emanate from the roof strata, coal pillars, and artificial support in response to the stresses induced by the mine opening. These pulses are sometimes referred to as "talk". Although it is clear that miners rely on roof talk to assess the roof's stability, it is not clear of what roof talk is composed. It has been described in a variety of figurative ways, but has not been scientifically characterized. As will be shown shortly, the purpose of this research is very specific. The ramifications, however, are very broad, and are, indeed, still being followed.

Jan 1, 1974

By C. E. Jordan

The fundamental properties of the Bureau of Mines patented dielectric separator were studied to provide insight regarding its design and operating characteristics. Force equations for mineral particles were derived and evaluated experimentally. High dielectric mineral recovery was proportional to the calculated effective dielectric force volume that surrounded each drum electrode wire. Electrode spacing was the most sensitive design parameter, requiring less than 0.4-cm electrode spacing for a good separation. Operating characteristics and ore characteristics were investigated. With a dielectric constant difference as small as 2, good separations were made on a laboratory scale at energy consumption below 12 kw?h/mt.

Jan 1, 1985

By William G. Pariseau

The purpose of this paper is to present a design procedure for the quantitative estimation of support load requirements in underground mines. Emphasis is upon the basic features of support behavior common to a large variety of support systems-bolts, timber sets, stope fill, steel arches, concrete liners and so forth. A strong reliance is placed upon fundamental principles and modern computing techniques for their quantitative implementation. Example problems illustrate the approach. Where artificial support is required, the ground in the vicinity of the face usually stands unsupported long enough for the support to be installed. At the time of installation, the load transferred to the support from the adjacent rock is essentially zero, although in some cases there may be an initial set load, for example, from timber blocking. With the passage of time and advance of the face, ground motion loads the supports. If the support system is properly designed, then the additional loading poses no threat to the safety and productivity of operations. If not, then difficulties may arise including high maintenance costs, hazardous work conditions and reduced productivity. Of course, over-design can be equally wasteful. Quantitative estimation of support loads is therefore essential to overall efficiency in mining.

Jan 1, 1975

By Scott Lawson

BOB FALCONER: Our next topic leader is Scott Lawson. Scott is manager of human resources for Independence Mining Company, Cripple Creek and Victor Gold Mining Company, Victor, Colorado. Scott has 25 years of human resources management experience in the mining industry, surface and underground, precious and base metals. His topic this morning is "It's the Employee That Counts." SCOTT LAWSON: When reviewing the topic of productivity in a union versus nonunion workplace, we need to look at who, and not what, can make the difference in ensuring the success of a production-oriented operation. It's not explicitly whether the property is unionized or not, but whether the employee team (including the "management group") is working together to accomplish common, shared, and meaningful goals. The bottom line is what action or actions can be taken to develop trust and to strengthen working relationships that challenge and compel employees to willingly share their particular areas of expertise. I want to share a real-life experience that happened to me during the summer of 1961. Perhaps some of you will be able to relate to the following story. I was an 18-year-old fresh out of high school, ready for my first true work adventure. I found summer employment for myself and two friends with the New York Central Railroad in Cleveland, Ohio. Our jobs were as laborers, laying ties and rails, and unloading ballast. We made $2.62 an hour. We were fat cats! My friends and I took on the job with a great deal of vigor, to the dismay of our fellow workers. These workers were unionized by the Railway Workers, which I believe were affiliated with the Teamsters. Talk about being naive, we wrote the book in 1961. When we took the jobs, we did not realize the employees were represented by a union, even though we didn't think they worked too hard. Within our first two weeks of work, we established new daily records for laying virtually twice as many ties as had been standard, and we nearly tripled production by the end of our hall of fame railroad careers. We even took naively to the next level by lining up the ties for our afternoon work shift during our lunch break. In 1961, we thought we were the Mantle, Maris, and Colavito of tie laying. For the younger set in the audience, we would have felt like the McGwire, Griffey Jr., and "The Big Hurt" Thomas of tie laying. A section of the union contract allowed for a 60-day probationary period during which the employee was evaluated and also exempt from joining the union. I will venture to say that, to none of your surprise, on day 60 we were asked to join the union, and on

Jan 1, 1998

JIM ARNOLD: Questions? Comments? Gary, were you gone when I made the comments about corporate puke? [laughter] SPEAKER: You were hiding. BRUCE CAVENDER, BHP Copper: Having worked in both places, I'd like to address the issue of the plant versus the corporate office. One thing to keep in mind is that we are all very engaged with the technical elegance of a lot of the work we do. There's some tremendous technical expertise in the plant. But remember, the guys in the corporate office are only thinking in one denomination, and that's dollars. So we'll see something like a spill, and for us it's a problem. At the end of the day, what the corporation cares about is the financial impact. So we've got to be careful to couch our solutions in dollar terms. JIM ARNOLD: Rebuttal? [laughter] DOUG HALBE: Are you going to rebut this one, Andy? ANDY CARTER, Oxidor Gold Corporation: No, I don't think so. I'm not up to it. I'd just like to address a question both to our panel and the floor. Those of us who've been in this industry any length of time have seen these same mistakes made over and over again. Wherever you go, year after year, plant after plant, you see the same problems. I guarantee you, Doug, that if we have a similar conference down the road, you're going to see the same thing. My question to the panel and to the floor is what is it about our industry that stops us from learning from our mistakes? What characteristic is it that prevents us from learning and makes us repeat the same mistakes over and over again? DOUG HALBE: That's a great question. Someone said in a meeting 10 years ago that if the people who design plants designed airplanes, the planes would be falling out of the air all the time. GARY SIMMONS, Newmont Gold Company: I've got an answer to your question as to why many plants are poorly designed. It's that the minute anybody demonstrates any sort of competence in plant design, they're promoted to a higher-paying job, and the talent pool is left with people of lesser experience. Just think about it: The people who have the experience and have demonstrated it more than once have moved up. JIM ARNOLD: I think that there's another reason, too. Seven or eight years ago I was chairing a session, and I challenged everyone in the session to some day publish an article about the design mistakes they'd made because we never talk about our mistakes. I'll

Jan 1, 1998

By Calvert D. Iles

Open-pit mines in the US and throughout the world are typically characterized by increasing operating costs and decreasing ore grades. Thus, companies must continue to improve their use of human and technological resources to remain competitive in the marketplace. Duval Corp. has historically been very sensitive to mining costs, in part because of relatively low grade copper-molybdenum ore bodies. These concerns have resulted in three haulage system generations at the 218 kt/d (240,000 stpd) Sierrita-Esperanza open-pit mine south of Tucson, AZ. Each generation has exceeded the performance of the one replaced. The latest system of portable crushers and conveyors reduces hauling costs by combining both hardware and technique. Savings are achieved not only bysubstituting conveyors for haul trucks, but also by permitting the crusher-convey or system to closely follow mining as the pit deepens and/or mining areas change location. The Duval system is capable of easy and inexpensive relocation in varying site configurations in relatively short time periods. Its implementation in active mining areas results in minimum disruption to both the mine operation and mine design. This haulage concept allows the mining engineer maximum freedom to design an open pit for profit rather than for equipment. Maximum savings with a portable system are achieved by minimizing truck haulage costs. At Sierrita, for example, the yearly estimated operating cost savings for each thousand feet of +10% truck ramp replaced by conveyors is about $1 million per portable crusher. A savings of $30 million could be achieved fora three-portable system overa 10 year period simply by reducing the average truck Iiftto the crusher by 30 m (100 ft), There is also the added capital expense of buying trucks to cover the additional 30 m (100 ft) of lift. Relocation costs are an important consideration in a portable system. Direct costs can become a significant operating expense if frequent relocations are necessary to take full advantage of potential haulage cost savings. A site preparation cost of $375,000, for example, would add an additional operating cost of 2.8¢/t(2.5¢/st) for a system handling 13.6 Mt/a (15 million stpy), assuming one move a year, In addition to the direct cost of site preparation, such as installation of retaining walls, apron feeder slots, and equipment pads, there is the cost of site renovation after abandonment. Indirect relocation costs, while less tangible and more dependent on specific mine design and scheduling, can be of significance. A slowdown in the mining rate or a less efficient mining plan can result from a site not being immediately available for mining after abandonment. Conversely, mining in narrow areas can be adversely affected if two or three month lead times are required for site preparation.

Jan 4, 1983

By L. Eros, R. H. King

The US Bureau of Mines has funded several research and development projects in computerized mine monitoring and control. Hardware and software components have been sufficiently developed so that mine operators have been provided with an efficient means to comply with federal regulations and increase mine safety. Several cost benefits have been realized as well, particularly with increased conveyor belt haulage availability. Western Fuels-Utah Inc. approached the Bureau to assist in planning, installing, and evaluating a computerized mine monitoring and control system because of the agency's research experience in this area. The installation was planned for Western Fuel's Deserado mine, located in Rangely, CO. Since a large, complex, underground mine producing about 2.4 Mt/a (2.7 million stpy) of coal was projected, the company anticipated significant benefits in safety and efficiency through a computerized monitoring and control system. A major part of the cooperative program was to document and evaluate the system design, installation, and operation. This will assist others to adequately design, specify, install, and operate future systems. Mine description The Deserado mine plan and layout have important impacts on the monitoring system requirements. Long range plans are to produce 2.4 Mt (2.7 million st) of clean coal annually from two longwall sections and four continuous sections. Presently, two continuous miner sections operate under 213 m (700 ft) of overburden in the 2.3 to 2.5 m (7.5 to 8.5 ft) thick D seam to develop main, submain, and panel entries have developed for a longwall. These began operation in December 1986. Belt conveyors haul the coal from the mining sections to a 1.4-m (54-in.) belt located in the upper compartment of the slope. The lower compartment contains a hoist for men and material transport. From the slope, the coal moves to two 9 kt (10,000 st) raw coal storage silos, then to a 680-t/h (750-stph) preparation plant. After cleaning, a 5.5-km (3.5-mile) overland conveyor carries the coal to a clean coal slot storage and rail load-out facility. An electric locomotive then transports the coal to the Bonanza Power Plant in Utah. Allen-Bradley monitoring and control hardware and software controls the preparation plant, with two PLC-3 programmable controllers and a Process Control Industries D-1200 color graphics interface. The system operator uses three "smart" color video display units and an alarm printer for hard copy records. Originally, it also monitored and controlled the conveyors from the bottom of the slope to the top of the raw coal silos, the preparation plant, the overland conveyors, the main mine ventilation fan, and the hoist. Some of these features, though, were later transferred to the mine system.

Jan 2, 1988

By Tore M. Larsen

The Rødsand Gruber mining company is a subsidiary of the Norwegian industrial corporation Elkem AS, and its mine is situated in the northwestern part of southern Norway. The ore from this mine is a relatively low grade, magnetite ore with a small amount of vanadium. The ore bodies are very irregular in shape, resulting in a high amount of waste rock intrusion in the stopes. The annual underground production in the mines is approximately 1 million t. Because of varying dimensions of the ore bodies, both transverse and longitudinal stopes are employed. The inclination of an ore body is usually 1.04 to 1.59 rad (60 to 90°), and the horizontal width varies up to 100 m. Sublevel stoping has been the traditional mining methods in this mine. Until a few years ago, the ore was primarily blasted using horizontal blasthole fans drilled from Alimak raises. Recently, however there has been an increasing demand for a les expensive mining method. Alternate systems were considered, and finally a method based upon large blasthole stoping was found to be the most suitable. GENERAL LAYOUT The general layout of a stope is shown in Fig. 1 As with all the figures in this chapter, only the prin¬ciples of the method are emphasized and the details may not be valid for any particular site in the mine. In transverse stopes, the horizontal width of the ore determines the length of the stopes. The average length is approximately 50 m, the width of the stopes is 20 m, and there is a 10-m wide vertical pillar between. The distance between the main levels is 60 m. Usually a horizontal (sill) pillar 10 m thick is left below the mucking level. Each stope is first undercut along the entire stope length. This undercut is made with 50.8-mm (2-in.) diam drill holes in a fan pattern. At the moment this is being done by a trackless Atlas Copco Promec jumbo equipped with two Cop 130 pneumatic rock drills. The drill drift is 4 X 4 m, and the crater is 20 m high. This leaves a 36-m stope height to mine with large blastholes. To achieve a fair portion of vertical drilling withlarge blastholes, there are two parallel drill drifts at the top of each stope. These drifts are 4 m high and 9 m wide, separated by a 4-m wide pillar in the middle of the stope. To ease the drilling of perimeter holes, the drifts extend 1 m into the vertical pillar on each side of the stope. The pillar will thus be only 8 m wide on the drill drift level, but 10 m wide down the rest of the stope.

Jan 1, 1982

By G. A. Kordosky

The control of pH in solvent extraction circuits is an old technique (1,2) but one which has a large potential for future use. The equilibrium position of any reaction which has hydrogen or hydroxide ions, either as products or as reactants, can be controlled by pH adjustment. Several examples of reaction types which are important in solvent extraction systems and which also show a pH dependence are shown in Figure 1. The examples were chosen to show the wide variety of reactions which fit the above criteria, but it is not meant to be a complete listing of all the possible reaction types, Some of the reactions are presented in a simplified form. It is the intent of this paper to discuss pH controlled solvent extraction reactions for some relatively simple systems through more complex ones.

Jan 1, 1979

By Nicholas T. Esposito

An advanced coal preparation plant has been built at Homer City, Pennsylvania, by Pennsylvania Electric Company, a subsidiary of General Public Utilities Corporation, and New York State Electric and Gas Corporation, as an alternative to utilizing flue gas desulfurization technology to meet the Federal Environmental Protection Agency and the Pennsylvania Department of Environmental Resources air quality emission regulations of 4.0 lb S02/106BTU for the two (2) existing coal-fired generating station Units No. 1 and No. 2, and a 1.2 lb S02/106BTU for the new Unit No. 3. The coal preparation plant is designed to process 5,200,000 tons of run of the mine coal annually and has a design capability to process 1,200 tons per hour via two (2) equal capacity 600 tons per hour preparation circuits.- The plant is designed to produce multi-product coal streams consisting of a middling product of medium ash and medium sulphur content, which is environmentally compatible to support operation of the two (2) existing generating Units I and 2, and a deep cleaned, low ash, low sulphur coal product capable of environmentally supporting the ambient air quality requirements of the new Unit 3 generating facility. The waste product from the process consists of high ash, high sulphur reject material. The process has the acronym MCCS (Multi-Stream Coal Cleaning System).

Jan 1, 1982

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The effectiveness of the grouting of saturated, fractured rock in the vicinity of underground workings depends to a great extent on the correct interpretation of the specific hydrogeological conditions at the site. During the planning of grouting operations, calculations of the hydrogeologic co-efficients and of the parameters of the isolating grout curtain(s) and the procedures for forming the curtain(s) must be based on valid hydrogeologic characteristics of the fracture system of the rock within each hydrostratigraphic unit (Anon., 1976). This chapter presents a discussion of the background information that must be collected for these purposes. Details of testing are presented in Chapter 3. The general design of new or the reconstruction of existing underground workings requires a broadly based organization having the expertise to develop a grouting operations plan once it acquires the necessary information. The needed information includes: 1) general information about the hydrogeologic section, 2) the engineering design of the underground workings, 3) the geology of the region, 4) the hydrochemistry of the ground water, 5) the hydraulic properties of the rock, 6) the characterization of all gases present, and 7) characterization of the rock's physical-mechanical properties which is necessary to avoid or control hydrofracturing . The geological documentation portion of the hydrogeological investigation is prepared based on the results of geologic mapping, geophysical surveys and on geo-exploratory operations at a regional and local scale. Geological data from the excavation of other underground workings in adjacent areas of the region is also included. Finally the results of site specific investigations in boreholes constructed at the site of the proposed underground activity are incorporated. A section of the preliminary report entitled "General Information about the Project Site" patterned after the parent STG guidance document on this subject must be com- piled based on the contents of geological reports and on the general construction plan for a new project or the plan for reconstruction of an existing operation. This section of the preliminary report must contain concise information about the conditions under which the planned grouting operations are to be conducted. The information must cover the geo- graphic, administrative, and economic subject areas also. Information about sources of electrical power, heat and water supplies, the presence and characteristics of local construction materials suitable for making grout (particularly clay and cement for the clay-based grout), transportation, and the status of communication lines and other services must be included in this section. Map scales for this section should be on the order of 1:25,000. The technical characterization of planned underground workings is presented in a project report chapter called "General Construction Plan for a New or the Restoration of an Old Operation. " The characterization comprises concise information about the purpose of the workings, the planned depths (for shafts) and the length (for horizontal and inclined workings), the inside and excavated diameters (for shafts), the cross-sectional area (for inclined and horizontal workings), and the face and mouth markers. If excavated underground workings exist in the region, then a concise description of them must be provided. The characterization of all excavations and all operational conditions must be specified. The location within the general structure of the proposed operation is specified. Flow charts must be included in this section that show: 1) the plan for opening the deposit, 2) the plans of the mining operations, and 3) the planned geological sections as they relate to the main workings. These graphical flow charts and appendices are drawn in scales of 1:2000 or 1:5000. 2.1 GEOLOGICAL CHARACTERIZATION The geological characterization of a site of proposed underground workings includes the following principal subject areas: stratigraphy, lithology, structural geology and a characterization of the status of fracturing. 2.1.1 STRATIGRAPHY AND LITHOLOGY A description of the geological section of the rocks to be intersected by the planned underground workings is complied on the basis of: 1) research data derived from core extracted from exploratory boreholes and monitoring boreholes, 2) the documentation and mapping of all natural out- crops in the region, 3) the data from all existing under-ground workings in the regions where operations are being canied out already, along with data from adjacent regions, 4) the data from surface and borehole geophysical investigations (standard and specially developed logging methods, and 5) regional stratigraphy. The geological description of the rock must express the maximum detail possible. The description provides the name of the rock, the granulometric composition (for fragmented rock), the composition and type of stratification, the drilling characteristics of the rock, a visual estimate of porosity and density for each stratum identified, the karstic

Jan 1, 1993

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

5.1 TECHNOLOGY FOR INJECTING GROUT INTO BOREHOLES The grouting of fractured rock aquifers is carried out in separate stopes' whose size is determined by the hydro¬stratigraphy and the hydrogeologic properties of the rocks. The number of grouting stopes required depends on the number of intervals in the hydrogeological section. Each grouting stope can include one or several aquifers. Com¬bining several water-producing strata into one stope is pos¬sible only when the values of their permeability coefficients are very similar. In order to achieve efficiency, as many aquifers as possible are included in each stope. In practice, the length of a grouting stope in a borehole usually ranges within 10 to 40 m, but occasionally up to 100 m or more. When conducting grouting operations through boreholes drilled from the face of underground workings, the stope's size can be determined by the thick¬ness of each fractured zone (fault) or by the length of the hole if the entire rock is fractured. Injecting grout into separate intervals of fractured rock can be done from the bottom to the top with ascending stopes or from the top to the bottom with descending stopes. Injection from bottom to top is always preferred. Injection also can be accomplished in separate fractured permeable horizons in the section. The STG integrated grouting method is based on the use of packer and injection equipment and technological schemes that facilitate injection in highly isolated fractured aquifers. For this purpose STG has developed a standard series of packers. 5.1.1 INJECTING GROUT THROUGH BOREHOLES DRILLED FROM THE SURFACE Grout can be injected according to one of four techno¬logical schemes depending on the depth of the fractured aquifers, their hydrogeologic properties and the availability of grout injection equipment if the area is remote (Fig. 43). In the first and most preferred technological scheme (1), the grout is injected from the bottom up with ascending stopes. When this scheme is employed, grouting holes are drilled to the entire projected depth based on the field investigations injection tubes is installed above the top of the first hydrostratigraphic unit to be grouted. This scheme al¬lows the grout to be injected only into the permeable stra¬tum or strata isolated by the packer near the bottom of the hole; it precludes the need to clean or redrill the hole before injecting grout into the next overlying stope. This ascending stope scheme is preferred because of its simplicity and ef¬ficiency. It is used in most of the grouting of saturated fractured rock for the purpose of isolating aquifers while excavating deep mine shafts in the USSR. The second technological scheme (II in Fig. 43) injects the grout in sequence from top to bottom with descending stopes. Injection under this scheme is accomplished through the hermetically-sealed mouth of the hole. It is most advis¬able to grout with descending stopes in saturated fractured rock wherein the aquifers constitute thick networks of frac¬tures. Under these conditions it is practically impossible to drill a grout hole to the entire depth of the underground workings due to the large production rate of ground water. In conducting isolation operations with descending stopes, additional work (relative to ascending stopes) is necessary to drill out the grout in order to create and inject the next stope. As a result, the total amount of drilling required to drill out grout can even exceed the volume of drilling of original rock. Consequently it is advisable to use this inefficient scheme only for injecting grout into holes that contain prolific frac¬tured aquifers at depths less than 150 to 200 m. The third and fourth technological schemes (III and IV in Fig. 43) are used in the selective grouting of separate aquifers. For example, these methods would be applied when a grout hole is drilled to its entire depth, wherein grouting of the upper aquifers must be done first so that the sinking of the first shaft can begin prior to deeper grouting. The third technological scheme is used for the selective injection of grout into an aquifer with a thickness of up to 5 m. For this work the DAU-1-2 removable dual packer is installed. It is lowered into the borehole on an injection pipeline. For aquifers with thicknesses of more then 5 m, the selective injection of the grout is carried out according to the fourth technological scheme; a combination of the DAU-2 hydrodynamic plug and the DAU-1 packing device is used. In order to implement this injection scheme, the DAU-2 hydro-dynamic plug is installed at the bottom of the fractured aquifer and the DAU-1 packer is installed at the top of the aquifer.

Jan 1, 1993

By Kenneth A. Grace

Introduction The 1980s have not been kind to the mining industry, especially in the United States. As mineral commodities prices plunged, marginal producers were squeezed out and then major players were forced to cut back or close down operations. Base metal miners suffered the most. Gold was all that glittered. As had been the case throughout min¬ing's history, exploration activity was an early victim of these depressed conditions. Mining companies had to economize drasti¬cally and exploration was deemed a nones¬sential activity. Funding for new explora¬tion ventures dried up as mining was seen as a poor investment. A national magazine even proclaimed the death of the industry. Indeed, ignoring matters of independ¬ence of supply and the relationship of min¬eral production to national security, it was argued that mining was but a small cog in the overall scheme of things in the United States. The industry made a relatively small contri¬bution to the gross national output. We were becoming a service industry economy, re¬member? But what of those countries where mining plays a major role in the economic well-being? In some, mining is the national economy. In a few specific cases, special conditions actually brought prosperity. Copper production in Chile is one example. There, high grade copper, low production costs, and a technically advanced industry reaped the benefits of mine closures else¬where. In most other cases, however, par¬ticularly in the lesser developed countries, whole economies were devastated. This article will show what one major mineral producer, Canada, did to ensure the survival and even growth of its minerals exploration activity during these lean years. Background While Canada is among the world's mining leaders, mining is not its dominant industry. Still, it plays a far more important role than in the United States. It is a major earner of foreign exchange, currently accounting for about 25% of the total value of exports. Through spinoffs and a multiplying effect, it is a significant employer. In the far north, particularly, mining is the major nongovernment industry and a leading factor in the opening up of frontier territory. The industry cannot be allowed to die because it is often the main economic underpinning for vast, remote areas. Thus, exploration for new deposits cannot be cur¬tailed significantly without it having a long¬term negative impact on the very fabric that melds such a large, sparsely-populated ex¬panse of country into a nation. Over the years, Canadian governments have employed various means to encourage the development of new mines. Often, these incentives were tax-oriented, such as the three-year income tax holiday that applied to new mines in the 1950s and 1960s. The advantage of the tax connection is that any such incentive policy can be applied across the board to the 10 provinces and two territories that make up the federation of Canada. This is important because mining, except for the two federally-administered northern territories, comes under provincial government jurisdiction. Mining taxation is a complex give-and-take between the central and provincial authorities. In Canada, expenditure on mineral exploration is an allowable cost against reve¬nue for tax purposes. This works well pro¬vided there is some revenue from which to deduct. New exploration companies, those with no income from mining activities, de¬rive little benefit from this type of tax provi¬sion. Similarly, in times of depressed prices and reduced or nonexistent profits, the tax deductibility of exploration spending loses its value even for the major mining compa¬nies. To encourage exploration in Canada during the lean years, a different sort of incentive was required. The instrument used during the 1980s was again tax connected. It became known as flow-through financing or, simply, flow-through shares. When it assumed its final shape, it worked dramati¬cally. Flow-through shares Flow-through shares are so-named because they permit tax benefits earned by a corporation to 'flow-through' to the share¬holder. Basically, when an investor buys a flow-through share and the proceeds de¬rived by the company from this transaction are used for Canadian exploration, the in¬vestor can claim a deduction for tax pur¬poses as if the exploration expenditure was made by him personally. Flow-through shares go back to the early 1970s when Canada revamped its mineral income tax law. At that time, it permitted full deduction of exploration and development expenditures and provided for an automatic depletion allowance of one¬ third of operating profits from mining. There was also the three-year income tax holiday for new mines. New legislation replaced the depletion allowance with an earned depletion arrange¬ment whereby one dollar of depletion was earned for every three dollars spent on ex¬ploration and development. This earned depletion was `banked' during a transitional period (to 1974). After that it could be deducted from resource profits up to a maximum of 25% of such profits in any one year, with the excess carried forward. To promote exploration and mine de¬velopment in Canada, the earned depletion allowance plus the continued deductibility of exploration and development expendi¬tures permitted the recovery of risk capital before taxation. The three-year tax holiday, however, disappeared. Also, mining com¬panies that did not reinvest in exploration lost the depletion allowance benefit.

Jan 1, 1989

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By Tony Walsh

Australian Stock Exchange Limited (ASX) -ASX is ranked 9th in the Morgan Stanley Capital International (MSCI) Index – only 2.02% of that Index. -1520 companies – 400+ mining & mining exploration. -Over 50% of Australians own shares in ASX listed co.s -Disclosure standards play a vital part in providing investors with confidence, thereby building depth and liquidity in the market.

Jan 1, 2003

By Joaquin Ruiz

Although Mexico is known for its important base-and precious-metal deposits, and lately oil, some industrial minerals play an important role in the Mexican economy. Sulfur, the most important industrial mineral produced, accounts for approximately 7.5 percent of the total value of mineral production. This commodity is followed by fluorspar, which accounts for 6.4 percent. Predominantly, the fluorspar deposits are very high grade (75 percent CaF) and are contained in lower Cretaceous limestone in the states of Coahuila and San Luis Potosi. Base-metal deposits in the area of Parral (notably San Francisco del Oro), however, have become important fluorite producers in their own right. (San Francisco del Oro has 12 percent fluorite gangue.) Salt from the Guerrero Negro solar-evaporation ponds in Baja California account for 6 percent of the total shares; phosphate from Baja California also accounts for 6 percent. Barite from man to deposits in Lower Cretaceous limestone in Coahuila and exhalative deposits in the Paleozoic section of Sonora account for 1.0 percent. In addition, Mexico is an important producer of gypsum, graphite, and celestite. Although graphite and celestite are not large-scale operations and thus do not contribute much to the Mexican economy, the Mexican graphite and celestite deposits are among the most important in the world; Mexico is one of the world's few sources of celestite. The celestite is in the form of large, high-grade mantos in Cretaceous limestones in northern Mexico.

Jan 1, 1987

By John C. Balla

The Troy deposit is located in northwestern Montana, approximately 17 mi south of Troy. The deposit is a stratiform, strata- bound, copper-silver deposit which occurs in the Revett formation of the Proterozoic Belt Supergroup. The Revett formation is approximately 1730 ft thick in the vicinity of the Troy deposit, and is divisible into three units. The upper Revett, approximately 250 ft thick, is the host for the orebody. The Revett represents a deltaic environment. The Troy deposit was discovered by Bear Creek Mining Company in 1 963 during the course of a reconnaissance stream sediment sampling program that was designed to discover strata-bound copper deposits. The deposit is approximately 7500 ft long, 1800 ft wide, and averages 60 ft thick. It is bounded on the north by outcrop, on the east by a post-mineral fault, on the south by diminishing grade and post-mineral faults, and on the west by diminishing grade. Ore reserves are 64 million tons with a grade of 0.76% Cu and 1.58 oz Ag per ton. The mine is presently operating at a production rate of 4.2 million oz of silver and 20,000 tons of copper per year.

Jan 1, 2013

By A. L. Holmes

Since the 1981 record of 54 mm tons of US fertilizer consumption, grain surpluses in the US have brought about massive acreage reduction programs, decreased fertilizer consumption, and resulting price pressures caused by excess capacity. The strong US dollar that reduced export sales of both grain and fertilizer, and new offshore manufacturing capacity using US engineering/contracting know-how have combined to put US producers of phosphate fertilizers in uncompetitive postures. While recent events suggest the industry may be growing out of this capacity problem, the cost of US phosphates will continue to be disadvantaged by such external factors as taxes, environ- mental regulations, and high power costs. There is no reason to expect help from the government in the form of reduced environmental regulation and taxation. In order to survive, phosphate fertilizer producers will have to develop technologies and adopt strategies that result in world competitive production costs. Current responses to the need to reduce costs include reduced energy costs through cogeneration, innovative reclamation techniques that create valuable land, and in- creased raw material recovery achieved by operator proficiency. While new technology offers long-term benefits for the producer, present efforts are concentrated on more mundane management efforts to reduce costs. Major attention is being given to the problems of labor utilization and productivity. Raw materials suppliers are being asked to renegotiate contracts which more appropriately reflect conditions in an industry operating at about 50% of capacity. Achievements in these and other areas will allow the producers to continue operating until longer term benefits materialize. `

Jan 1, 1986

By B. Hearn, O&apos

Falconbridge, Ltd. operates six mines (the strathcona, Fraser, Lockerby, Onaping, East and Kidd Creek) in the Sudbury and Timmins districts of northern Ontario (Fig. 1). These mines vary in depth to approximately 1500m and experience a wide variety of ground conditions. Problems of greatest concern include rockbursting, backfill pillar stability, wall and pillar stability, and the use of cable anchors. A study was initiated approximately two years ago to identify how numerical models could aid in the examination and possible understanding or solution of these problems. This paper discusses the use of numerical models at Falconbridge and describes a case history of their use in examination of rockbursting at the Strathcona Mine.

Jan 1, 1988

By M. Frenzel, D. Ebert, K. Bachmann, A. D. Renno, R. Möckel, J. Gutzmer, J. Krause

With the increasing demand for metalliferous and mineral raw materials, and consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium (V). Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, Xray fluorescence (XRF) analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 weight percent V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples, calcium carbonates also significantly contribute to the V deportment, while wuestite, lime and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the Vbearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.

Aug 1, 2024