Search Documents

By Moussa Wone, William Levy, Christopher Caruso, Zachary Spera, Thomas Hennings, Richard Stacy Kinchen, PE Joel Kantola

"Owners constructing new combined sewer overflow (CSO) systems increasingly seek to have project design lives of 100 or more years in response to the growing size, complexity, and cost to construct and operate these systems. However, a codified and universally accepted approach to achieving this goal in the United States does not currently exist since service life prediction is a relatively new technical field. This paper discusses how the 100-year design life requirement was met for the design of tunnels, drop shafts, and diversion structures in the DC Clean Rivers Program (DCCRP). The authors identify some commonly referenced publications, present the testing framework used by the program manager to characterize the CSOs, review the design criteria used to guide the 100-year design life development, and establish guidelines to be considered by program managers and designers when implementing similar extended design life requirements in other CSO control programs.INTRODUCTIONLike many older cities in the United States, the sewer system in the District of Columbia consists of both combined sewers and separate sanitary sewers. When the capacity of a combined sewer is exceeded during storm events, the excess flow, which is a mixture of sewage and storm water runoff, is discharged to the District’s receiving water bodies (Anacostia River, Potomac River, and Rock Creek) and tributaries through outfall structures. This excess discharge during storm events is called a combined sewer overflow or CSO. A total of 53 CSO outfalls for the combined sewer system are listed in DC Water’s National Pollutant Discharge Elimination System (NPDES) Permit issued by the U.S. Environmental Protection Agency (EPA). The DC Clean Rivers Program (DCCRP) will reduce the number of CSO outfalls into the Potomac and Anacostia Rivers and decrease flooding in DC neighborhoods during extreme rain events by capturing, storing, and conveying diverted CSOs to the Blue Plains Advanced Wastewater Treatment Plant."

Jan 1, 2016

By E. M. Williams

The U.S. Bureau of Mines recently conducted a limited-scope study on the use of lineament analysis and electromagnetic geophysics to better identify the surface expressions of faults at the Cimmaron Mine near Raton, NM, an operating longwall mine in the York Canyon mine complex. Two normal faults were encountered by the mine, one during gate road development and drilling and another only through drilling. The potential ground control problems and offsets associated with these faults will severely impact long-range development plans, so it is essential to know the lateral extent of these faults within the coal reserves. The surface topography at the site is fairly rugged, yet outcrop exposure is poor. There is no obvious visible geologic evidence to indicate that the faults identified at depth extend to the surface. Both the geophysical and remote sensing techniques provided information on the presence and extent of important geologic structures which could not be gained just from drilling and surface outcrops. The geophysical surveys also were invaluable in confirming the presence of subsurface geologic structures in the vicinity of the lineaments assumed to be associated with the faulting.

Jan 1, 1995

By Ratnakar Singh, Raj Kishore, Kisor Kumar Sahu, Ranjeet Kumar Singh, Ganesh Chalavadi

The Falcon concentrator is capable of separating minerals in fine size classes based on their differential density. Separation of mineral particles depends upon the fluid flow characteristics and relative movement of particles in a fluid. In the present study, a fluid flow characteristic inside the Falcon concentrator was established through experimentation and modeling. The Falcon concentrator has two fluid entry points: (a) Fluid entering through gravity assisted feeding system and (b) Fluid entering through the fluidized hole on the concentrator wall. In order to identify the role of fluid entering the concentrator, a tracer was injected into the system. As per the tracer based experimentation, it was established that fluid entering through the gravity based feeding system is responsible for thin flowing film formation in the stratification zone where particles are stratified based on their relative density. The momentum balance and continuity equations were simplified for a high centrifugal force field, and the fluid velocity profile was estimated inside the thin flowing film. Estimated fluid flow profiles will help to simulate the particle trajectories inside the Falcon concentrator. The influence of rotational speed, fluid flow rate, and cone angle on the fluid velocity profile were investigated. Fluid thickness over the concentrator wall is also estimated, and it is typically of the order of ~150–200 μm.

The mining industry is one of the three pillars of the Namibian economic development, besides tourism and the fishing industry. Generating 20 % of the GDP and more than 50 % of the export income, half of this amount derives from the diamond mining industry. In 2008, the annual production of 2.2 mio carat achieved an income higher than 1.44 billion Namibian Dollars (more than 750 mio Euro). After the global recession in early 2009, which also caused a significant downcrease in production to only 0.93 mio Carat, the diamond mining industry easily restored itself and the production figures for 2010 are expected to be even higher than those achieved in 2008. Compared to other diamond producing countries, Namibia is mainly producing diamonds of highest quality (jewellery quality), with less than 10 % of the mined diamonds not falling into this category. This high quality stands also for the worldwide highest prize achieved per carat. With 370 $US per carat it is more than four times higher than that of the average South African stone. In 1908 the finding of the first diamonds in the Namib desert close to the coastal town of Lüderitz was reported by a Mr Stauch, railway inspector for the then German colonial railway company. This event immediately triggered a Diamond Rush and subsequently the set-up of the restricted diamond mining area ?Sperrgebiet? through the German colonial administration. In 1913, only five years after the first mining operations had started, the steadily increasing production allowed for more than 20 % of the diamond production worldwide. After the First World War, the new South African government concentrated all mining activities in one organization, CDM (Consolidated Diamond Mines of South West Africa) which in following decades conducted an extensive and detailed exploration of the whole Sperrgebiet and started numerous new diamond mining operations.

Jan 1, 2011

By R. Addison, P. V. Avotins, E. Martinez, L. A. Haas, D. K. Mortenson, E. EI-Shall, R. D. Kulkarni, M. D. Flavel, S. Chong

Mineral processing activities in general reflected the economic ills of 1981 and early 1982, but in some areas the depressed state of the industry resulted in increased activity. As were all aspects of the minerals industry, processing plant operations were severely affected by the recession-prone economy, by sagging prices for primary metal products-copper, molybdenum, nickel, iron, manganese, and especially uranium-and numerous shutdowns and layoffs. Copper production by major producers in Arizona and Utah was severely curtailed; Amax, the major US molybdenum, producer did considerable belt-tightening; and the uranium industry was in a state of disaster. Even the precious metal superstars-gold and silver-were affected, with a steady decline throughout the year in world market prices. Perhaps hardest hit have been newly developed properties, particularly in the uranium industry, and old-line properties where historical development impacts today. No longer can such properties afford the luxuries, for example, of a long haul distance between mine and plant or continued use of antiquated facilities. Surprisingly enough, the very state of the economy has caused increased activity in some sectors of the mineral processing industry. In mill design, although large projects have been tabled, smaller projects have gone on, with innovations in design, often for cost-saving reasons, that will affect future designing approaches. Economic restrictions are impacting on mill flowsheets as researchers look for improvements and better, less expensive techniques. Other unit processes-hydrometallurgy, pyrometallurgy, concentration, materials handling-are impacted by the need for a better, less costly product. Although at the end of the first quarter of 1982, no major environmental legislation had been enacted, rumors persist that there will be a loosening of some of the stricter standards, both in the requirements themselves and in the time allowance for implementation. The year had seen some relaxation in how current legislation and standards are administered. For example, in OSHA (Occupational Safety and Health Administration) operations, there has been a shift toward voluntary checking of industry compliance with work rules, rather than emphasis on agency inspections. However, the industry continues to view environmental factors as having major influence on future operations and efforts to design for environmental safety are becoming almost as important as the processes themselves. Throughout the industry there has been a further focussing on project management, recognizing the necessity for tight control of budgets and schedules-and the systems used to effect them. Materials Handling Review prepared by A. T. Yu, ORBA Corp. The frenzy of coal export activities has continued into 1981. Many modern export terminals are now in construction while others have either been held up or cancelled. Economics and environmental permits have been some of the major problems. Currently under construction are terminals in Newport News, VA; Charleston, SC; and Baltimore, MD. Expansion of existing facilities at Mobile, AL, and New Orleans, LA, is also well under way. A wide variety of systems and components are being used. They include traveling shiploaders, tunnel and bucket wheel reclaim¬ers, stackers and high line trippers, and bottom and side dump-type car dumpers. Manufacturers from Japan and Europe have been participating along with domestic suppliers. As an attempt to avoid environmental problems, a system of loading and unloading coarse coal

Jan 5, 1982

By S. P. Chong, Peter V. Avotins

The iron and steel industry continues to operate at depressed production levels due to the low level of demand for steel and foundry products. Crude steel production in the Western world dropped by 13.7% from 459.3 Gt (506 billion st) in 1981 to 396.4 Gt (437 billion st). The reduction was particularly severe in North America where the industry suffered a loss of 37.3% from 123.6 to 77.5 Gt (136 to 85 billion st). This reduced level of production severely affected iron ore and agglomerates output. Substantial curtailment was made in both sintering and pelletizing plants to meet reduced demand. The pressure on these plant operators shifted from quantity to quality. With energy cost becoming an ever increasing part of production costs, conservation was a major area of emphasis. Iron Making Sinter has continued to be the favored burden for blast furnaces overseas. As hot metal production declined and excess sintering capacity developed, many of the overseas operators that have been using pellets found it advantageous on hot metal production cost to increase the ratio of sinter at the expense of pellets. This was the case despite the depressed price level of pellets in the world market. In North America where pellets have been the predominant burden material-mainly because it is necessary to pelletize the fine grain iron ores available domestically-there was also increased interest in sinter usage. Bethlehem Steel Corporation's 13.6-m (44.5-ft) furnace at Sparrows Point experimented with a burden with more than 70% of sinter during the second half of the year and indicated some favorable results as compared to its previous 50% super flux sinter and 50% acid pellet burden. The blast furnace operators continued to press for improved burden quality. In addition to the emphasis on the importance of burden chemistry and quality, uniformity, much emphasis was placed on improving reducibilitiy and high temperature metallurgical qualities. These burden properties were recognized to hold further promise in reducing fuels rates. Sintering With reduced consumption caused by the cutback in hot metal production, many sinter plants sat idle while others operated at greatly reduced rates. The deemphasis on production in many plants allowed them to experiment with various means to reduce operating costs. The most notable action was the introduction of low cost South American pellet feed fines into the sinter ore mix. These feed fines, which are finer than 150 µm (100 mesh) ore, were previously thought to be too fine for sintering. However, when the full production rate is not required the use of up to 40% in the ore mix was reported to be successful with the aid of burnt lime and adequate premixing and granulation of the sinter mix before sintering. The emphasis on quality and tighter cost control also has resulted in a further breakthrough in sintering technology. It was recognized that good feed preparation-including selection of compatible ores, good blending, good pseudo-particle formation, additive size control increased bed depth, and closed control of the sintering bed heat pattern-could allow the production of high quality sinters with much lower heat input and FeO level. Bed depth of more than 600 mm (23.6 in.) was practiced in a number of operations. Total heat input of better than 1.3 GJ/t (290,300 kcal per st) has been achieved. Kawasaki Steel's Chiba Works has also achieved a 5.3% SiO2 in the sinter with good quality. The low heat input approach allowed production

Jan 5, 1983

By D. Carr, C. Anderson, M. Deal, C. Larson

"Construction of the OceanaGold Haile operation’s process plant in Kershaw, South Carolina is currently under way, with ore through the mill expected in late 2016 and commercial production expected in early 2017. The process is designed to treat 6,350 tonnes per day with minor upgrades required to achieve 8,270 tonnes per day. Plant optimization during detailed engineering, combined with a focus on de-risking the process, has resulted in numerous process changes since the initial design. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio operation, whilst identifying potential expansion opportunities. INTRODUCTION Haile Gold Mine is located in Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching from 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that delineated 2.02Moz. of gold in reserve at an overall grade of 2.06 g/t. OceanaGold acquired Romarco Minerals and the Haile Operation in October of 2015. OceanaGold operates under a risk management philosophy in all aspects of operation, both corporately and at each individual business unit, and has implemented numerous process changes to eliminate or mitigate risks identified in the initial design of the processing circuit, and provided increased opportunity for optimization and expansion. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio Operation, and identifies potential expansion opportunities. INITIAL PROCESSING CIRCUIT DESIGN An extensive metallurgical test work program was undertaken by Romarco Minerals and third party laboratories during the initial design phase of the Haile project [1]. This preliminary test work provided the technical information as a basis of plant design. The initial flow sheet for the Haile processing circuit is shown in Figure 1 (see APPENDIX). The plant is designed to process 6,350 tpd (7,000 stpd) on an annualized basis. The process begins with a jaw crusher followed by a SAG and ball mill grinding circuit to reduce particle size to P80 74 µm. A flash flotation cell treats 50% of the cyclone underflow in the ball mill circuit. Grinding circuit product is sent to a rougher flotation circuit to recover gold-bearing pyrite. The flotation concentrates from flash and rougher flotation are reground to P80 13 µm using stirred media detritors (SMD’s). The rougher flotation tail is pumped to the carbon-in-leach (CIL) circuit for gold recovery. The reground concentrate is pre-aerated prior to being pumped to the CIL circuit. The CIL circuit is a hybrid circuit with eight tanks. Tank 1 leaches the pre-aerated concentrate only, and tanks 2 through 8 leach the combined flotation tailing and tank 1 discharge. The carbon strip circuit is a standard pressure Zadra system, followed by electrowinning, and refining using an induction furnace. CIL tailing passes through a cyanide recovery thickener prior cyanide destruction and then pumped to the tailing storage facility (TSF)."

Jan 1, 2017

By Markus Thewes, Mario Galli

"INTRODUCTIONProject-related studies showed that lab tests are a helpful tool for the planning of EPB tunneling and soil conditioning in cohesionless soils. This type of ground commonly represents the extended application range for EPB shields, which demands for a treatment with additives. Considering soil conditioning with foam, so far, approaches exist for the investigation of the foam quality and of the conditioning behavior of soils (e.g. (EFNARC GUIDELINES 2001 2003)), but not any standards for testing procedures related to soil conditioning. State-of-the-art research on the topic is and was conducted for example in Bochum (Germany) cf. (Budach 2012; Maidl 1995), in Lyon (France) cf. (Quebaud et al. 1998), in Oxford and Cambridge (Great Britain) cf. (Borghi 2006; Peña Duarte 2007), in Delft (Netherlands) cf. (Bezuijen and Schaminée 2001), in Turin (Italy) cf. (Borio 2010; Peila et al. 2013; Vinai 2006), and in Aachen (Germany) cf. (Vennekötter 2012). Additionally, applied science is reported by the tunneling practice and suppliers of conditioning agents. Although the research focus in all these and further studies varied, similar test methods and test series were applied. A standardization of essential properties and testing methods (setup and procedures) however did not take place. The results from laboratory testing can only function as index values for practice because in the studies, production and application of the conditioning agents mainly takes place under atmospheric conditions. Nevertheless, the tests enable basic understanding of feasibility as well as processes and interactions going on during soil conditioning. For recommendations for standardized and reproducible testing see (Budach 2012; Budach and Thewes 2015).The most extensive investigations on the flow behavior of soil-foam mixtures have been performed by using the slump test from concrete engineering, cf. (DIN EN 12350-2 2009-08), which originally is applied on evaluating the workability of fresh concrete. Although this test does not describe the actual flow behavior, it rather represents an index on the workability, very much experience exists with this test method. Besides others, the workability – or flow behavior – of the EPB support medium certainly is a major factor of influence on the properties of the material in the excavation chamber and thus, for effective tunneling with EPB shields, cf. (Galli and Thewes 2014). For a summary of various investigations on the workability of conditioned soils using the slump test and resulting recommended slump ranges see (Budach 2012; Vinai 2006). Thereof, slumps between 10 and 20 cm have been reported as suitable workability for EPB applications. However, there is actually not much known about the real flow behavior of soil-foam mixtures related to rheological properties such as the viscosity (?) or potential yield stresses (t0). These physical values are necessary for a realistic determination of face pressure, for the design of required torques, and for an evaluation of the material flow at different locations in the excavation chamber, in the screw conveyor or on the conveyor belt. To generate a linear pressure distribution at the tunnel face, as it is assumed a priori, a low-viscosity fluid is favorable, whereas in the screw conveyor, a high-viscous fluid is needed for a controlled pressure decrease. On the conveyor belt, yield stress plays an important role preventing deliquescence and spilling from the belt. Attempts in characterizing the actual flowing of soil-foam mixtures have so far only been made by few researchers, the application of rheometry is rare."

Jan 1, 2016

By G. E. McClelland

Introduction Many discoveries have been made during the-past decade of low grade gold-silver deposits in the western US. This has stimulated development of low cost cyanidation procedures for precious metal extraction. Heap leach cyanidation techniques possess considerable potential for application to these low grade ores, small ore bodies, mine strip waste, and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successful, these resources must have good permeability to achieve uniform distribution of the cyanide solution throughout the heaps. Some of the most difficult of the gold and silver ores to treat successfully by heap leaching are those containing excessive amounts of clays, or fines generated by crushing. Presence of excessive amounts of slimes, -50 µm (-270 mesh), in the heap leach feed will slow percolation, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap. This causes the leach solution to run off the sides of the heap rather than penetrate the ore bed. The problem of heap leaching ores with fines can be aggravated while preparing ore heaps because of the natural sorting of coarse and fine material that occurs. This phenomenon results in concentration or ore fines in the center of individual ore piles and concentration of larger rock fragments of the lower slopes and base of the pile. When the individual piles within the heap are leveled off for the installation of the sprinkling system, additional segregation occurs as the fines sift through the coarser ore particles. This results in localized areas or zones with marked differences in permeability. Consequently, the leach solutions follow the course of least resistance. They percolate down through the coarse ore regions and bypass or barely wet areas that contain large amounts of fines or slimes. Effective use of marginal gold and silver resources by heap leaching required development of new methods to achieve more uniform size distribution when preparing ore heaps and better slime control during leaching. Early methods Agglomeration and balling of crushed ore to produce a porous and more uniform feed material for heap leaching is a viable method for treating clayey ores. Researchers from the US Bureau of Mines in Reno, NV began agglomeration pretreatment research in the mid-1970s for applications to and exploitation of these poor percolating feed materials. Little attention had been given to such methods before the Bureau's research. In 1905, T. C. Scrutton developed a unique technique for obtaining rapid vat leaching of a clayey ore where the gold was finely disseminated. His technique consisted of rolling the ore down a chute inclined at 60° to form agglomerates or balls readily permeable by the cyanide solution. However, these agglomerates lacked rigidity. And, to ensure good percolation leaching and washing, they could not be bedded in layers more than 1 m (3 ft) deep. If this depth was exceeded, it is difficult to obtain uniform leaching and washing. This results in reduced gold recovery. Shepard and others in 1937 studied the addition of lime and carbon dioxide or calcium carbonate to gold-bearing tailings to form agglomerates suitable for vat leaching. Satisfactory percolation flow rates were achieved in 90 g (3 oz) scale experiments, but the reagent requirements were cost prohibitive. Agglomeration and pelletizing has been used in other segments of the mineral industry. This technique was first used successfully around 1911 for pelletizing iron ores. Since then, agglomeration

Jan 7, 1986

Introduction One hundred years ago, a recent college graduate created the US aluminum industry. He found an economic way to crack the primeval bond that makes the metal so special. Aluminum doesn't "rust" - oxidize progressively. Rather, when exposed to air, it instantly forms a gem-hard but microscopic oxide coating. This seals off oxygen from the metal underneath. Scratch it and the seal reforms instantly. That tight chemical bond is the reason the metal is not found in nature; it exists only as a compound. The bond had to be broken to free the shiny metal. But once it is free, that self-sealing protection, alongside a remarkable strength-to-weight ratio, offers a marvelous material. Until 100 years ago, finding a way to do that economically was a challenge that defied science. Then it was solved, in a remarkable coincidence, on both sides of the Atlantic. And the way was paved for a material that would become the second most widely used metal in the world. Until that time, aluminum was a rare and precious metal. But then two young scientists independently invented the process that took aluminum outside the laboratory and into applications ranging from pots and pans to spacecraft. Discovery of aluminum Other major metals - copper, iron, lead, gold, and silver - had been used for thousands of years. But aluminum was entirely unknown until 1782, when French chemist Antoine Lavoisier suspected its presence. It was not actually discovered until Sir Humphry Davy, in England, detected it in clay in 1807. It was first isolated as a free metal only in 1825, by Denmark's Hans Christian Oersted. For years, laboratory methods yielded aluminum only in tiny amounts costing about $1200/kg ($545 per lb) - $13,333/kg ($6000 per lb) in today's dollars. Methods developed by French scientist Henri Sainte-Claire Deville in 1854 cut the cost to about $200/kg ($90 per lb). King Frederick VII of Denmark had a helmet of aluminum and gold. And Emperor Napoleon III of France reportedly served his most exalted guests at a state dinner with aluminum plates. He left the lower ranks to dine from pure gold. Deville and others continued to reduce production costs. But the price of aluminum still rivaled silver - $31/kg ($14 per lb) versus about $35/kg ($16 per lb) for silver. Then in 1884, a 2.8-kg (6.25-1b), 230-mm-tall (9-in.-tall) aluminum pyramid was cast as the tip of the Washington Monument. It was probably the first architectural use of aluminum. And it is still there after more than a century. The attractive properties of aluminum were obvious: it is lightweight but strong, conducts heat and electricity, reflects light and other electromagnetic radiation, and resists corrosion. But its commercial promise was blocked by its cost. In 1885, the price of aluminum was $17.70/kg ($8 per lb). It stayed there for the next couple of years until the Hall-Heroult process brought it down sharply. Hall-Heroult process lowers aluminum costs The characteristic that kept aluminum hidden so long continued to thwart chemists. Aluminum clings to oxygen so tightly that it is never found as a free metal in nature, and it is hard to break that bond chemically. The best chemical methods of the 1880s required sodium, and sodium itself was expensive. At Oberlin College in Ohio, chemistry professor Frank Fanning Jewett advised his students that anyone who could make aluminum inexpensive would do humanity a favor and get rich as well.

Jan 3, 1987

By Peter G. Sechiari

The Rio Tinto-Zinc Corporation Limited (RTZ), through it exploration company Riofinex, commenced exploration for bauxite in the Amazonia region of Brazil during 1970. Following' encouraging indications, exploration licences were taken out and an exploration programme was initiated In February 1975, a preliminary 'feasibility report indicated that a project, based on the Miltonia plateau located close to the town of Paragominas in the State of Para, was viable and that barging might offer an economic solution to getting the product to an ocean-going port. A, decision was taken in April 1975 to proceed with a full feasibility study. In the latter stages of the study, an engineering consortium of Mendes Junior and Bechtel do Brasil was employed to review, and modify if necessary, the concepts that RTZ had developed for the project's operation. With these concepts agreed, the consortium was requested to make capital and operating cost estimates, and these became available during February 1978. The deposit is being developed by a Brazilian company Mineracao Vera Cruz S.A. (MVC) in which the present share-holding is owned 64 percent by RTZ and 36 percent by Companhia Vale do Rio Doce (CVRD). RTZ is a British based international group of mining and industrial companies with interests in almost every major metal and fuel. CVRD is a Brazilian mining company, 85 percent owned by the Brazilian Government, with a major interest in iron ore and also other non-ferrous metals. It is intended, in due course, that the company will become majority owned by Brazilian interests.

Jan 1, 1979

By Agne Rustan

INTRODUCTION This work is a continuation of the preparatory study by Rustan and Stöckel 1979 (3) and (4) of the possibilities to introduce automatic mine ventilation in Swedish mines and construction works. The preparatory study has been financed by the Swedish Board of Technical Development. In the study it was recommended that an automatic step by step control of the fans near the working place due to diesel exhaust emission would be the best solution. A more advanced alternative would be to regulate the fresh air continuously in proportion to the contamination. The latter alternative has been studied by Boliden Mineral Co in the Udden mine. In this study it was found that the air supply could be regulated continuously but it was very important where the sensors feeling the contamination were placed. An intense study of the environment underground is now being planned by our division together with specialists from the National Board of Health and Safety, The Swedish Work Environment Fund, LKAB and the local Governmental Inspection of the Workers Safety. Different gases, radon, dust, airspeed, moisture temperature and pressure is planned to be measured continuously and correlation between the parameters is going to be established to decide the best measurement parameters for regulating the system. The best situation of sensors is also going to be studied. Despite this work hasn't been done yet this paper covers some of the problems which could be encounted with continuous regulation. In this report the environment has been studied during the test with step by step regulation of fans by radio. Diesel vehicles are the largest polluters under ground in Swedish mines and we have therefore suggested that the large diesel vehicles should regulate the fans. The goal of this study has therefore been to find how active diesel vehicles should be able to start and stop gallery fans at both intake and return air. In this paper different methods for activating fans are discussed. Then the best methods are chosen and tested in the mine. In this study we have found that changes of temperature is a cheap and effective method to start and stop cross cut fans in sublevel caving and radio signals seem to be an attractive system for start and stop of gallery fans. This work has been done in close collaboration between LKAB in Kiruna and the University of Luleå - Division of Electronics and Division of Mining and Rock Excavation. A reference group for the project has been established with ventilation experts from the mines, representatives for the local mine worker's unions and authorities from the local Governmental Inspection of the Workers Safety. VENTILATION SYSTEM STUDIED In the project the ventilation system at LKAB in Kiruna has been studied. The mining method used is sublevel caving with 9-13 m slice height. The air is heated winter time over ground by hot water heat exchanger. The main fans are pushing air down to a main distribution level along the 4000 m long and about 100 m wide orebody. From the distribution level, air is taken through shafts down to the sublevels, where it is pushed through the levels by local gallery fans on both intake and return side, see fig 1. The air ( ~ 8 m3/s) is moving freely through the gallery head. The cross cuts are ventilated with smaller fans, diameter 500 mm, and flexible duct, see fig 2. The aim of this study has been to study how to start and stop gallery- and cross fans and examine the environment when the fans are stopped . In Sweden there are no regulations telling that a minimum of air amount must be supplied. Instead the hygienic limits must be fullfilled.

Jan 1, 1981

By Warren D. Stanford

The Alligator Ridge mine is a near-surface gold mine located in a remote area 113 km (70 miles) northwest of Ely, NV. The deposit was discovered in 1976 by a lone prospector working under a grubstake contract for Amselco Minerals Inc. Evaluation of mine potential proceeded quickly. Favorable drilling results led to feasibility and mine design studies by the end of 1978. Mine construction began in early 1980. By September of that year, the process plant was fully operational. The first gold was poured a few months later. Alligator Ridge is designed to produce 1.9 t (60,000 oz) of gold each year. The projected mine life, based on proven reserves, is to mid-1988. However, Amselco is actively conducting exploration nearby for additional reserves to extend the mine's life. Amselco, a subsidiary of the British Petroleum Co., is based in Denver, CO. The company is mine operator and jointly owns the project with Nerco Minerals Inc., a wholly-owned subsidiary of Pacific Power and Light. Alligator Ridge is Amselco's first US mining operation. Geology Alligator Ridge, so named because it appears in outline to be an alligator at rest, contains disseminated micron gold embedded in iron-streaked siltstones. Although definitive conclusions have not been drawn on age and origin, the gold ore bodies are probably young by geological standards. They were formed in a recent volcanic period still evidenced in parts of Nevada by geysers and hot springs. As these superheated solutions rose through the permeable siltstones, they deposited minerals in the rock and formed the present gold ore bodies. During 1977, an extensive soil geochemical sampling program with additional geologic mapping and outcrop sampling were conducted. The results generated several drill targets. Initial drilling was performed in November and December 1977, and ore grade mineralization was encountered in the first drill hole. The Alligator Ridge mine is unusual in relation to other and more recent western US mineral discoveries in that it occupies an area that had no previous mining history. The ore deposits are hosted in upper Paleozoic sedimentary rocks that consist predominantly of a thick carbonate sequence. The main ore host is the Devonian-Mississippian Pilot shale, which occurs locally as a sequence of thin bedded calcareous, carbonaceous siltstones and claystones. The maximum observed thickness of the Pilot section in the mine area is about 140 m (460 ft). Rocks in the Alligator Ridge area have been folded into a series of low amplitude anticlines and synclines that strike north-south and plunge to the south at about 20°, with limbs that dip nearly 20°. The folds have been truncated and deformed by later high-angle faults that generally strike northwest. Although multiple stages of movement are evident on the fault systems, the youngest period of activity is along the major northeast trend. The predominant structural pattern in the area is of the basin- and range-type high angle normal faults. Alligator Ridge is actually a horst block between two basin and range faults. Vantage Ore Deposits There are three principal ore deposits within the Vantage Basin and several smaller satellite mineralized areas. The three Vantage deposits are encompassed in a mineralized zone that covers an area 915 m (3,000 ft) long and 305 m (1,000 ft) wide. All mineralized zones have been outlined by more than 600 rotary drill holes, with an average depth of 150 m (500 ft). Mineralization occurs in both carbonaceous and oxidized rocks. The carbonaceous gold-bearing material is not amenable to current heap leaching practice. Therefore, only oxidized ores are now treated. The carbonaceous gold-bearing material is segregated and stockpiled as it is encountered during mining. The three ore bodies occur along a north-northeast strike, with mineralization becoming progressively deeper from north to south. The ore block dimen-

Jan 6, 1984

By John H. Bassarear

How best to grind? This article compares conventional crushing and grinding circuits to semiautogenous circuits, reviews recent installations of each circuit, and describes seven methods of using autogenous or semiautogenous techniques. In addition, steel and power consumption data are reported and benefits of a dedicated digital computer are discussed. Size reduction is the most expensive operation in most mills. Crushing and grinding are usually the greatest part of capital costs. They often make up 60-70% of total mill operating costs. Picking the proper crushing and grinding method must, therefore, be done with great care, so the best circuit is chosen. In the past 10 years, there has been a strong trend toward using autogenous or semiautogenous grinding in mills throughout the world. Autogenous grinding is favored when the ore is quite competent and a fine grind is needed. Semiautogenous grinding is applied when fine crushing could cause severe problems or when ore varies in hardness or competency. The taconite iron ores of northern Minnesota fit the description for an autogenously ground ore and many are successfully ground that way. Most im¬pressive are the nine lines of 11 x 4.9 m (36 x 16 ft) mills powered by 9 MW (12,000 hp) motors at Hibbing Taconite. Porphyry copper and molybdenum ores fit the description for semiautogenous grinding. Recent installations include Highmont in British Columbia, Canada, and Quintana in New Mexico. Sampling Many mills have been built based on inadequate sampling data or insufficient tests. With the cost of many mills exceeding several hundred million dollars, it is mandatory that geologists, mining engineers, and metallurgists work together to prepare representative testing samples. Simple, repeatable work index tests are usually sufficient for rod and ball mill tests. However, pilot plant tests on 50-100 t (55-110 tons) of ore are frequently necessary for autogenous or semiautogenous mills. Preparation and selection of the test sample is of utmost importance. Procedures for autogenous and semiautogenous mill pilot plant tests are relatively simple for those experienced in running them. Reliable and repeatable results can be obtained if simple, fundamental procedures are followed. The accompanying figure shows a typical conventional crushing-grinding circuit with three stages of crushing followed by ball mills or a rod mill-ball mill combination. This flowsheet is typical of many mills that have been built throughout the world. Also shown is a typical semiautogenous (SAG) circuit with feed coming directly from a primary crusher, and the semiautogenous mill product going to the separation process. Many similar semiautogenous circuits are built today because they are simple and flexible, lend themselves readily to high tonnages, and usually cost less to build and operate. With some ores, it is possible to send mine-run ore directly to the semiautogenous mill, eliminating the need for a primary crusher, as at Benquet's Dizon mill in the Philippines. An autogenous or semiautogenous circuit, as the name implies, uses the ore itself to assist in the grinding process. Generally, for this type of circuit, the ore must be competent so large ore chunks can be used to grind smaller ones. If ore alone is used, then the circuit is autogenous; but if balls are added to supplement the charge, then the circuit is termed semiautogenous. Ore competency is not always a criterion, to break up large pieces and wash away cementing material. Autogenous and semiautogenous mills have been very successful on relatively soft uranium ores where the values are frequently found in the material that cements together the sandstone grains. Autogenous Circuits When an ore is hard and competent, it is always possible it might make good "pebbles" that could be used for fine grinding media. Seven methods have been tried using combinations of autoge-

Jan 6, 1982

Throughout the 1970s, the US Bureau of Mines rode an ebb tide in Washington political circles. In rapid fire succession, the agency lost its mine health and safety enforcement responsibility (1973), a large portion of its energy research responsibility (1975), and then its fuel statistics functions plus a sizable portion of its coal R&D (1977). By 1978, johnny-come-latelies in the Energy, Labor, and Interior Departments had siphoned away from the Bureau some $125 million in program responsibilities as well as 900 of its employees. The bruising decade came to a close with a Department of Natural Resources proposal that, in its original form, would have scattered the Bureau's responsibilities to the winds. "There is no doubt in my wind," said Lindsay Norman, acting director of the Bureau of Mines (see box), "that were the Bureau to continue down the path it was on, the next step was closing the doors and going out of business." The doors are still open, but erosion of responsibilities had a devastating effect on the resources available to fulfill the Bureau's mission. Devastating, too, in terms of internal morale, considering the Bureau had six directors in a 10-year span. "When the troops are in the trenches and are being shot at," Norman said, "they need a leader-hopefully, a permanent one- that can get them advancing. This is something the Bureau did not consistently have in the 1970s." In September 1978, Roger Markle climbed aboard as director of the Bureau to rejuvenate the 70-year-old agency. He resigned only six months later* but the program Markle set in motion is being carried through by Lindsay Norman. Since Norman's appointment as acting director, he has spent considerable time on the road explaining his agency's redefined goals. At one such stop in Duluth, Norman and his two deputy directors, Charles Kenahan and Mike Kaas, answered the following questions. Lindsay, you were the principal architect in the Bureau's 1979 reorganization. How about a glimpse of what that entailed? Toward the end of the 1970s, after almost a decade of steady dismemberment, we reached what we felt was a critical point in the Bureau's history-we had the choice of redefining and strengthening our organization to meet the mineral challenges ahead, or continuing down the path toward the agency's eventual demise. We felt the Bureau's mission too important to abandon, so in 1978 with Roger Markle as director we initiated a six-month, no-holds-barred intro spection of just what the Bureau should be doing, why, and toward what ultimate national needs. And what did this self-reflection reveal? That there is, indeed, a unique federal role for the Bureau of Mines-that of a lead agency for influencing mineral decisions and pioneering tomorrow's technologic advances. Don't confuse us with policymakers, we're not. But we are policy analysts; we're scientists, engineers, and mineral professionals who can offer a sorely needed source of objective, accurate information to decision makers in both the public and private sectors. I feel there is no better brain trust in government than the Bureau when it comes to mineral expertise-of course, I'm biased. Do I understand you to say the Bureau of Mines is an advocate agency for the minerals industry? We plead no parochial interests, nor ought we, but from our viewpoint a sound minerals industry is extremely important to the broader national goals of security and a healthy economy. US dependence on foreign sources for critical minerals, the increasing noncompetitiveness of some US mineral sectors, and the array of land use issues surrounding mineral-rich lands all have much more serious implications than many otherwise informed people seem to recognize. In your estimation, how vulnerable is the US to foreign mineral suppliers? Let me make a distinction between dependency and vulnerability. The

Jan 4, 1980

By D. Nilsson, B. Aaro

To find out if there are any potential savings in "in-the-wall haulage for open pits," the Swedish companies ASEA and Kiruna-Truck in 1984 gave us financial support to study this solution in more detail. In the study, the use of in-the-wall haulage was studied for three hypothetical open pits with different sizes and shapes. Annual ore production rates also varied. A part of this thor¬ough study was published by the Swedish Mining Research Foundation (see Report F 8444, "The Use of Electric Trucks and In-the-Wall Haulage in Open-Pit Mining," in Swedish with an English Summary). Although in-the-wall haulage is of interest in some open pits, the local terrain is important for profitability. The authors do not think in-the-wall haulage is of any major interest for the mining industry. The following is a summary of some of the author's findings. To place the haul road in the wall is not of interest in open pits with declining metal contents in the bedrock. In such mines, the volumes from the haul roads will not yield reve¬nues. The cost per m3 for an underground haul road is much higher than for a haul road in the pit. This means that it is only of interest to place the haul road in the wall when mining gets deeper than about 50 m (165 ft). In-the-wall haul roads will reduce flexibility in the pit, and it will make necessary the use of smaller equipment with lower productivity and higher costs per ton. As Hustrulid, et al. show (Table 4), excavation savings of material hauled are very low, $0.10 to $0.25/t (0.09 to 0.27 per st). The extra operating cost, due to lower productive equip¬ment, will normally be much higher and thus destroy the whole idea with in-the-wall haulage. If electric trucks are profitable for in-the-wall haulage, it is normally also profitable to use electric trolley assist for trucks on the haul road in the pit. But the profitability of using electric power is different in different countries, and depends on the relation between the cost for electric power and diesel fuel. In the US, diesel fuel is inexpensive compared with electricity, but in a country like Sweden, diesel fuel is much more expensive. In most open pits, the trucks have to move a considerable distange from the loader until they reach a final haul road in the wall. A trolley line along such temporary haul roads will be exposed to flyrock. It is normally less expensive to perform rock support from the open pit than from underground ramps in the wall. In Fig. 8, Hustrulid et al. gives the impression that the underground haul roads will be very close to each other. This is seldom the case. Figure 1 shows a haul road in the wall. The haul road passes through each cross-section only once. Ar¬ranging a reliable dewatering and rock support system from only one underground ramp is probably impossible. Many more drifts are therefore necessary. In our report, we also studied what would happen if the final pit slope is increased by 5°, using underground drifts in the wall. Our conclusion was that the extra cost for drifts, rock support, pumps, etc. destroys the whole idea, and that it was better to accept a higher stripping ratio with the haul road in the pit and to use conventional low-cost open pit equipment. Finally, we think it is would be difficult to try to reduce the safety factor when determining the slope angle by moving the haul road in the wall. Minimizing the risk for pit wall collapse is also important with in-the-wall haulage, primarily because men and equipment will be working in the pit, but also to guarantee many accesses between the pit and the haul road in the wall.

Jan 1, 1989

By Gregory R. Wagner

As you know, NIOSH is the part of the United States Public Health Service with responsibility for conducting and supporting research leading to prevention and control of occupational diseases and injuries. Some years ago, NIOSH went through a process of identifying and leading occupational health and safety problems in the United States. Candidate problems were evaluated in terms of the number of people affected, the importance of the effects, and how amenable the conditions are to preventive interventions. Lung diseases were ranked first on the resulting list. Diseases from mining continue to contribute substantially to this unfortunate position of prominence. The work of the Generic Center is one of many answers to this critical problem. Although the research is often expressed in terms of dust characterization or dust control, the reality is that high dust levels are much like high blood pressure. No one cares about hypertension per se. We are concerned about the consequences of exposure to untreated high blood pressure--heart disease, kidney disease, and stroke. Similarly, if dusts were truly only a nuisance, there would be little justification for the diverse research program supported by the Bureau of Mines or by NIOSH. But mineral dusts do cause a range of significant health problems: pneumoconiosis, bronchitis, and emphysema. The research supported by the Center is aimed at doing something about them. Within a public health approach to occupational health, we have a hierarchy of interventions. Primary prevention of problems is prevention at the source: solving a problem before it affects a worker. What we call secondary prevention is an attempt to identify health problems at a sufficiently early stage that some intervention will interrupt the disease process or the development of significant impairment. Tertiary prevention refers to rehabilitation of the worker who has already suffered significant loss of function. At NIOSH, and in the Generic Center research programs, the focus is on primary prevention. Basic investigations into those things about specific dusts that promote or reduce toxicity is critical for our understanding of how to prevent disease. Also, the search for engineering solutions to reduce or control dust generation is essential to solving problems of dust over-exposure. But until the engineers create the foolproof safe environment, it will also be necessary to discover better ways to identify the earliest markers of disease. To do this, we must explore and explicate the basic mechanisms of disease through laboratory investigations as well as human observation and physiologic testing. The unique opportunity provided by the Generic Center program and highlighted in this diverse program over the next few days is that these efforts are being carried out in multiple disciplines concurrently. Also, there are periodic small and large gatherings such as this one where investigators have the chance to get together, formally present papers, and informally stimulate each other's progress towards disease prevention. To ignore the potential for this cross-cutting interaction would be a significant loss. To take full advantage of it is potentially revolutionary. I recently pulled out a book I hadn't read since I was an undergraduate. It specifically concerns the nature of intellectual ferment surrounding the development of the concept of a sun-centered rather than an earth-centered universe in the sixteenth century. The book is about more than developments in astronomy: it is a discussion of the nature of scientific revolutions. Scientific revolutions result from the brilliance, insight, and good fortune of the few superimposed on the evolutionary work of the many. They both cause and reflect significant itellectural and social ferment. For example, the revolutionary work of Copernicus in recognizing the limitations of the concept of an earth-centered universe reflected contemporaneous developments in optics, mathematics, physics, economics, and philosophy.

Jan 1, 1991

By Henry O. Ash

On June 16, 1982, Rio Blanco submitted a request to the US Minerals Management Service for a suspension of operations under its federal oil shale lease. The company also wanted a five-year delay in the requirement for further minimum royalty payments and a five-year extension of the primary lease terms of 20 years. The request was granted in late July in the midst of yet another slump in oil shale activity. Rio Blanco holds one of four Federal oil shale leases that were granted under the Interior Department's Prototype Oil Shale Leasing Program in 1974. That year the DOI offered for lease six federal oil shale tracts, two each in Colorado, Utah, and Wyoming. The leases in Colorado and Utah were granted for substantial bo¬nus bids as shown in Table 1, but the Wyoming tracts had no takers. In the eight years hence, no oil shale has been produced commercially. Indeed, the prospects for successful oil shale development have fluctuated widely, continuing a 60-year- old cyclical pattern in the fledgling industry. The prototype program was developed and initiated while this infant industry struggled to begin anew, without the benefit of any federal oil shale leasing regulations, or any history of federal oil shale leasing at all. Permanent regulations were not required because the effort was limited and designed to provide the foundation for any future leasing program. Section 21 of the Mineral Leasing Act of 1920, a Nov. 30,1973 Federal Register notice, and the leases themselves constitute the legal and regulatory framework for leasing and developing prototype oil shale tracts. The prototype leases contain some unusual provisions including installment payments of the bonus bids, credit of early development costs against payments due the government, adjustment of royalty rates according to regional crude oil price fluctuations, and unusually extensive and detailed environmental stipulations. Several of the provisions were intended to provide incentives for early development and financial penalties for failure to develop. The requirement for minimum royalty payments in lieu of actual production royalties beginning in the sixth year of the lease falls in the latter category. After the sixth year, the required minimum payment is increased east year through the 15th year by an increment equal to that due in the sixth year. The minimum royalty then remains the same through the final five years of the primary lease term. Minimum royalty is calculates on a different production level for each prototype lease, based on the quantity of 125 L/t (30 gal/st) shale estimated to be recoverable from. each tract by room-and-pillar mining. That mining system was selected for reference as the only proven extraction method for oil shale at that time (early 1970s) The minimum royalty (production) rate was calculated for each tract by direct comparison of its estimated recoverable 125-L (30-gal) resource to a hypothetical tract containing 1.9 Gt (2.1 billion st) of recoverable 125-L (30-gal) shale. For the hypothetical lease tract, the minimum production for the sixth year was calculated to be 3.2 kt/d (3,500 stpd), increasing by a like amount each lease year through the 15th to a daily production rate of 31.7 kt (35,000 st). Under this formula, the hypothetical lease tract would yield $16 million in minimum royalty payments over the 20-year primary lease term if there were no production, no development credits taken, and no adjustment of the royalty rate due to fluctuation of regional crude oil prices. The production rate of 31.7 kt/d (35,000 stpd) was a somewhat arbitrary figure that was considered, in the early 1970s, to represent a minimum size for a commercial oil shale operation. A production rate of 7.9 dam3/d (50,000 bbls/day) soon supplanted that smaller mine production figure as a rule of thumb for the minimum size for a commercial facility. The proportional relation-

Jan 11, 1982

By J. E. Moyle

Introduction In October 1983, Rio Algom Ltd. decided to develop the East Kemptville tin deposit. This decision was the result of intensive geological and metallurgical evaluation work, as well as careful studies of environmental and marketing aspects. The property is located about 54 km (34 miles) northeast of Yarmouth, Nova Scotia, near the village of East Kemptville. Geology The geological setting is a granitic intrusive at the contact with metasediment. The tin mineralization is in the form of cassiterite (SnO2), which is about 80% tin. Sulfides are associated with the deposit containing silver, copper, and zinc, which are recoverable as byproducts. The mineralization is associated with quartz veins and greisen alteration. In the center of the deposit, the zones are so close together they have the appearance of a massive or porphyry type deposit. Ore Reserves The mine plan is based on 56 Mt (62 million st) at 0.165% tin. Up to the ninth year, mill feed will average about 0.2% and lower grade material will be stockpiled. In later years, the average grade will be 0.16% tin. A 0.08% cutoff grade is planned for the entire 17 years of production. East Kemptville is a relatively low grade tin deposit, and only a combination of favorable circumstances has made it economic. • The ore body is situated at, or very close to the surface, permitting mining by open-pit methods at a very low stripping ratio. • The tin occurs in relatively large crystals that allow for good recovery by gravity techniques. • It is ideally located in a well-settled area, with all essential infrastructural requirements already in place. • The positive and cooperative response from various governmental agencies involved are encouraging. Mine Plan The mine plan incorporates an initial pit, followed by three expansions to the ultimate pit. Mining will be at 14 kt/d (15,000 stpd) and will include 9 kt (10,000 st) of ore plus 5 kt (5,500 st) of waste and low grade. After five years, the mining rate will increase to 21 kt/d (27,500 stpd). It is planned to drill vertical 165-mm (6.5-in.) blast holes on a 6-x 6-m (20- x 20-ft) pattern. Bulk slurry explosives will be used to break the rock. Loading will be with hydraulic shovels into 70 t (77 st) haulage trucks. The trucks will deliver the ore to a 13 x 20 m (42 x 65 ft) gyratory crusher, where it will be crushed to 150 mm (6 in.). Secondary and tertiary cone crushers will be used to further crush the ore to 13 mm (0.5 in.). Process Design Tin extraction technology is practically unknown in North America, but Rio Tinto Zinc, which has a 53% ownership in Rio Algom, is involved in tin production in the UK. Rio Algom has used this experience and expertise in metallurgical evaluation work and in tin-related aspects of plant design. Mineralogical and metallurgical test work have been performed, both on laboratory and pilot plant scales. Mineralogical work was done largely in the UK, the laboratory test program was carried out at the Lakefield research facility in Ontario, and pilot plant work was conducted in Australia. This program has resulted in significant improvements in recovery and concentrate grades, over best projections that could be made before this work was carried out. Concentrating Process The concentrator is being designed to process about 9 kt/d (10,000 stpd). The first step is to reduce the size of the ore to -700 µm (-24 mesh) in a rod mill/ball mill grinding circuit. The ball mill will operate in closed circuit with high capacity banana-type screens. The screened product will be deslimed to 30 µm (560 mesh) with cyclones, then passed over the pri-

Jan 4, 1984

By D. Nilsson, B. Aaro

To find out if there are any potential savings in "in-the-wall haulage for open pits," the Swedish companies ASEA and Kiruna-Truck in 1984 gave us financial support to study this solution in more detail. In the study, the use of in-the-wall haulage was studied for three hypothetical open pits with different sizes and shapes. Annual ore production rates also varied. A part of this thorough study was published by the Swedish Mining Research Foundation (see Report F 8444, "The Use of Electric Trucks and In-the-Wall Haulage in Open-Pit Mining," in Swedish with an English Summary). Although in-the-wall haulage is of interest in some open pits, the local terrain is important for profitability. The authors do not think in-the-wall haulage is of any major interest for the mining industry. The following is a summary of some of the author's findings. To place the haul road in the wall is not of interest in open pits with declining metal contents in the bedrock. In such mines, the volumes from the haul roads will not yield revenues. The cost per m3 for an underground haul road is much higher than for a haul road in the pit. This means that it is only of interest to place the haul road in the wall when mining gets deeper than about 50 m (165 ft). In-the-wall haul roads will reduce flexibility in the pit, and it will make necessary the use of smaller equipment with lower productivity and higher costs per ton. As Hustrulid, et al. show (Table 4), excavation savings of material hauled are very low, $0.10 to $0.25/t (0.09 to 0.27 per st). The extra operating cost, due to lower productive equipment, will normally be much higher and thus destroy the whole idea with in-the-wall haulage. If electric trucks are profitable for in-the-wall haulage, it is normally also profitable to use electric trolley assist for trucks on the haul road in the pit. But the profitability of using electric power is different in different countries, and depends on the relation between the cost for electric power and diesel fuel. In the US, diesel fuel is inexpensive compared with electricity, but in a country like Sweden, diesel fuel is much more expensive. In most open pits, the trucks have to move a considerable distange from the loader until they reach a final haul road in the wall. A trolley line along such temporary haul roads will be exposed to flyrock. It is normally less expensive to perform rock support from the open pit than from underground ramps in the wall. In Fig. 8, Hustrulid et al. gives the impression that the underground haul roads will be very close to each other. This is seldom the case. Figure 1 shows a haul road in the wall. The haul road passes through each cross-section only once. Arranging a reliable dewatering and rock support system from only one underground ramp is probably impossible. Many more drifts are therefore necessary. In our report, we also studied what would happen if the final pit slope is increased by 5°, using underground drifts in the wall. Our conclusion was that, the extra cost for drifts, rock support, pumps, etc. destroys the whole idea, and that it was better to accept a higher stripping ratio with the haul road in the pit and to use conventional low-cost open pit equipment. Finally, we think it is would be difficult to try to reduce the safety factor when determining the slope angle by moving the haul road in the wall. Minimizing the risk for pit wall collapse is also important with in-the-wall haulage, primarily because men and equipment will be working in the pit, but also to guarantee many accesses between the pit and the haul road in the wall.

Jan 1, 1990