Search Documents

By Felicia F. Peng

Flotation process is particle hydrophobic surface-based separation technique. To improve the essential flotation steps of collision and attachment, and reduce detachment probabilities between air bubbles and hydrophobic particles, a selectively designed cavitaion venture-tube can be used to generate very high numbers of pico-nano bubbles to flotation column. Fully embraced by those high numbers of tiny bubbles, hydrophobic particles are readily attracting those tiny bubbles to their surfaces. The results of column flotation of Pittsburgh No.8 seam coal are obtained in a 50 cm ID and 162cm height flotation column equipped with static-mixer and cavitation-venture tube, using kerosene as collector and MIBC as frother. Design of experiment procedure combined with statistical two-stepwise analysis method are applied and attempted to made the optimizing the grade and recovery. The effect of independent variables on response has been explained. Combustible material recovery of 85-90% at clean coal product of 10-11 % ash are obtained from feed of 29.6% ash, with reduced amount of frother and collector than that used in conventional column flotation. The column flotation process utilizing the pico-nanobubbles can also be extended to the lower limit and upper limit of particle size ranges for better recovery minus 75 µm and 300-600 µm, respectively.

Jan 1, 2013

By Steven W. Hunt, Steven B. Fradkin, Roger J. Maurer

During the 1980s and 1990s, twenty deep shafts were constructed in Milwaukee to depths from 85 to 91 m (280 to 300 feet) through soil and weak rock thicknesses ranging from 37 to 69 m (122 to 227 ft). Adjacent compressible soils, settlement sensitive structures and high groundwater levels required that shafts be constructed without dewatering. Contractors attempted several methods of ground support and groundwater cutoff. Significant problems developed during construction of 11 of the 20shafts. One shaft collapsed; groundwater blow-ins occurred at five of the shafts; and seepage caused unfrozen windows at three of the freezewalls. Ultimately, combinations of grouting and ground freezing were utilized to complete all of the shafts into bedrock. This paper discusses the main design and construction challenges experienced and the lessons learned.

Jan 1, 2003

By B. Farshadi, B. Asi, M. J. Habibian

"In this paper, the most significant environmental aspects that are identified in the Taft Copper Project (TCP) are the quality and quantity of water, pollution of the existing watercourses and post-mining land use, matters such as air and noise pollution are deemed to be of less significance. Analysis has been performed for Do Nothing Alternative, Pre-stripping Phase, Mining Phase, Closure and After-use Phases. Analysis of the environmental assessment of TCP was carried out in three stages. In the first stage, the general negative and positive aspects of the project were identified. In the second stage the intensity, magnitude and significance of the environmental impacts of the project were identified. The third stage is related to the final conclusions of the assessment team and the relevant reasoning. A modified Leopold Matrix was adopted for evaluating the significance and magnitude of the environmental impacts. For this project, the matrix was modified to allow the assessor to take account of negative and positive numbers."

Jan 1, 2011

By Larry DeGraff

With the increase of new mine development in the past several years, many coal mines have decided to self- perform the design and construction for their slope development projects. The development process of determining the proper configuration is challenging, and a major economical consideration. Greenbrier Smokeless Minerals engineering staff and consultants, along with DSI/American Commercial, developed a support configuration that was best suited for their slope. The developmental process took into consideration the length of slope, depth of slope at the high-wall transition, economics of a single or multiple entries, waterproofing, stresses on the steel supports and lagging during the backfilling operation. This paper describes the developmental concept of using a single entry, side by side configuration, using steel ?Banjo String? supports with steel plank lagging, to develop a long term permanent installation in a cut and cover application.

Jan 1, 2009

By Stefan Lorenz, Robert Galler

"The technical lifetime of underground structures does not only depend on the long-term behavior of individual support elements and material characteristics, but also on various boundary conditions, which influence the entire long-term system behavior of the structure. Thanks to the construction of second tunnel tubes and the corresponding cross passages sampling of support materials such as shotcrete, concrete of the inner lining and rock bolts including sheet membranes is possible. To evaluate the stresses and the supporting effects of the tunnel shells, flat-jack tests and different simulations were performed. With these simulations the percentage of the load bearing behavior of the shotcrete shell can be determined. From the results, conclusions for new design approaches for tunnel construction should be generated. New concepts, in which the outer lining is part of the permanent support elements can be considered. This approach would be applicable for conventional as well as mechanical tunneling. INTRODUCTION Tunnels are an indispensable part of modern transport infrastructure. As multi-generation structures their long-term preservation as well as their technical service life is of central importance. The current state of research in the field of durability of structural elements must be considered separately. In almost all areas a prediction of materials and structural components towards lifetime exists. System-wide investigations were rarely performed, so that there is no technical lifetime consideration of the outer lining in systems included. In this study the mechanical behavior of the interface connection in a double shell lining (DSL) tunnel was investigated in laboratory tests. Objective The target of this work is, at first, to create a large database with the lifetime of different structural elements and materials, which may be the basis of durability considerations of tunnels. Secondly, the goal of these investigations is to optimize tunnel designs and their dimensioning regarding to the technical lifetime. For that matter, it is necessary to analyze the selected approaches of the loss of strength and stiffness of the outer lining."

Jan 1, 2016

By A. Subbotin

During developing the Ingulska mine at the Mi-churinske uranium deposit in the central part of Ukraine the radioactive rock dumps have been piled. A height of dumps reaches to 15-25m. They occupy a large territory and can be a source of covering with radioactive dust the area around the Ingulska mine. Uranium content exceeds 0,01% in all dump rocks samples while in the dust fraction samples it ranges from 0,01 to 0,06%. Uranium content in road dust at the dump?s foot reaches 0,137%. A new (for Ukraine) method of f-radiography of tree and bush leaves sampled at the territory about 100km2 has been used. It is based on fission of 235U nucleuses due to heat neutron influence in a nuclear reactor and on following study of the Lausan films with tracks drawn by the fractures of these nucleuses. Uranium content of the dif-fusion-disseminated dust type is (0.9-22.2)?10-6% while in the individual particles it can be considered much more because of burned holes in Lavsan above them. The dust content with uranium in Kirovograd reaches to 20-50 part/cm2 while near the dumps it ranges from 100 part/cm2 to 300 part/cm2 in the radius of 1,5-2km from the Ingulska mine.

Jan 1, 2005

By F. Touboul, M. Thiercelin, K. BenNaceur

Introduction The need to develop accurate predictive hydraulic fracturing simulators arises from the consideration of vertical containment for the fracture. Fracture height growth from a pay zone into adjacent layers has been shown (see Cleary [I]) to depend on three sets of parameters for the different strata: - elastic properties, - closure stress variations, and, -fracturing fluid leak off, and poro-elastic stresses. Qualitative analysis of the effects of these parameters has been reported in the literature. The first effects were described by Van Eekelen, using simple elasticity considerations [2]. The effect of stress variations was described numerically by Simonson and a1. [3] and experimentally by Thiercelin [4]. Effects of back stresses induced by fluid invasion on fracture propagation were considered by Cleary [5]. In order to couple these effects, a numerical code al- lowing the simulation of three dimensional growth of a hydraulically induced fracture has been developed with the ability of representing the effects of heterogeneities on fracture lateral and vertical extension. The model is based on a new variational formulation of the boundary integral representation of three-dimensional elasticity. The fluid flow and elasticity equations are solved using a moving mesh representation which offers enough flexibility to enable the simulation of any closure stress distribution. Simpler models representing fracture height growth (P3DH models) have been developed [6] [7] that approximate the fracture by a series of one dimensional segments, and the limitation of such approaches is examined in this paper. 1 Description of the model 1.1 Fracture Geometry Hydraulic fracturing simulations involve the coupling of solutions to elastic deformations, fluid flow in the fracture, and fluid leak off into the formation. Since the use of direct solution techniques (i,e,,3D finite elements) is prohibitive, the method used in this study is baaed on a boundary integral representation of the 3D elasticity equations. 1.2 3D Models The classical representation of the problem of a fracture in an infinite medium by boundary integrals is [8]: [ ] where u is the unknown displacement field, r n is the traction operator, I? is the fracture surface, and K is the Kelvin tensor of fundamental solutions to the elasticity operator. Using the notation: [ ] for the displacement discontinuity (or fracture width), one can attempt to solve the boundary integral relation using surface integrals (91 or the displacement discontinuity technique, first introduced by Crouch [lo], and extended to three-dimensional problems [Ill. However, numerical problems arise since the Kelvin tensor has a singularity in

Jan 1, 1986

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By Lawrence A. Taylor

The rocks and minerals of the moon will be included among the raw materials used to construct a lunar base. The lunar regolith, the fragmental material present on the surface of the Moon, is composed mostly of disaggregated rocks and minerals, but also includes glassy fragments fused together by meteorite impacts. The finer fraction (i.e., < lcm) of the regolith, the soil, is probably the most important portion of the regolith for use at a lunar base. For example, soil can be used in bulk as insulation against cosmic rays, for lunar ceramic and abodes, or for growing plants. However, beneficiation of the soil can provide other feedstocks. For example, the soil contains abundant solar-wind implanted elements, as we1 1 as various minerals, particularly oxide phases, which are of potential economic importance. These components of the soil are sources of oxygen and hydrogen for water and rocket fuel, helium for nuclear energy, and metals such as Fe, Ni, Al, Si, and Ti. The uses of the lunar materials only await a fertile imagination.

Jan 1, 1990

By G. Potts, K. Raiber, T. BoBo

Effective control of balling line circuits is a problem taconite companies have been dealing with for over thirty years. The sensitivity of balling circuits to changes in moisture, bentonite, concentrate particle size, and other operating parameters are the main reasons for control problems. This paper presents test results and describes the integration of existing instrumentation with a digital image analysis system on a balling circuit. This work has the goal of developing control strategies to automatically adjust water spray and bentonite addition, to optimize the size distribution on the roll screen and reduce the variability in control between balling attendants, resulting in more consistent greenball product quality.

Jan 1, 2003

By David A. Holmes

After a century of variable government-supplied housing on their cold, windswept lands, and facing extremely limited natural resources and no timber, the Standing Rock Sioux Tribe has launched a study into alternative housing approaches for their people. Considering that they have little more than the soil and limited river aggregates under their feet, the Tribe has elected to consider adobe and earthen-wall construction. Earthen construction is no stranger to the Sioux lands. Smaller tribes, including the Mandan, Arikira, and Hidatsa, lived here among the Sioux in earthlodges for centuries. Such earthlodge structures were not unlike the Southwestern jacal style-a framework of upright branches and branches covered with mud-employed by the Anasazi about A.D. 700-900. Indeed, the Sioux people themselves evolved from earlier earthlodge dwellers. Indigenous peoples in New Mexico, Arizona, and neighboring Mexico have used earthen-wall housing for many centuries, reinforcing Sioux observations that this is today an earth-friendly, cost-effective, and practical approach. The Cheyenne River and Pine Ridge Sioux Reservations also recently have conducted studies on earthen- wall construction. This paper describes the search for and evaluation of potential raw-material resources for earthen-wall/adobe construction on the Standing Rock Reservation in North and South Dakota. Significant resources of clay/silt materials (8 million tons in the Striped Cloud clay bed) suitable as adobe binders and sand-and-gravel aggregate (2.5 million tons) that could support earthen/adobe construction have been identified throughout the Fort Yates Flat area on the Reservation. Also addressed is how adobe and rammed-earth construction could add to the diversity of reservation construction and address future Tribal housing and other building needs.

Jan 1, 1999

By S. Henley

There is much in common between the requirements of open-pit mining and quarrying operations. Both involve the extraction of large volumes of material from surface excavations. The principal differences are of degree: open-pit mining of materials such as coal or gold generally involves the extraction of only small volumes of &apos;mineral&apos; and large volumes of waste-they are operations with very high stripping ratios, and are made viable only because of the high unit value of the extracted mineral. In quarrying operations, the unit value of the mineral - sand, aggregate, limestone, or clay - is much lower, but stripping ration Are also lower. Thus the same techniques of geological modelling, reserve estimation, and pit planning are applicable, as is shown in two examples from the British quarrying industry. In each case, a primary requirement is the definition of production volume or tonnage. Sometimes, this need may be addressed simply by the use of a survey data processing package. However, in other cases, such as the two examples addressed in this paper, of sand and clay quarries, detailed assessment of the variation of mineral grades is a vital part of the exercise, and simple volumetric modelling cannot in itself be sufficient. In these cases, a block model approach using simple logical and numerical post-processing is also required to obtain required parameters for commercial classification of the products to be extracted. Pit designs themselves may be optimised by use of algorithms such as Lerchs-Grossmann, but the value of mineral produced can be dependent on factors other than its grade in any one part of a single pit, and the &apos;optimised&apos; pit itself must be considered only a good sub-optimal. Given the right degree of healthy skepticism, and a software package with sufficient flexibility to be adapted readily to the rather different requirements of the quarrying industry, there is no reason why the quarrying industry should not benefit from the many years of investment in mining software technology.

Jan 1, 1989

By Martin Knights, Geoff Featherstone, John Flanagan, David Lawrence

The proposed paper will address specific transport, engineering, environmental and community related issues concerning the current construction and future operation of Europe’s biggest urban road tunnel project—the US$500m Dublin Port Tunnel. Situated in Ireland’s capital, the three mile long, 40 ft diameter twin tunnel project encounters a range of ground conditions using TBM, Shield, Cut & Cover with diaphragm walling and major slope stabilisation and Multi-jacked pipe techniques. Where possible units of measurement are given in feet and inches.

Jan 1, 2003

By E. De Souza, J. F. Archibald

"Many underground mines use cemented backfill to mitigate environmental effects associated with tailings disposal. The large energy needs associated with mine backfilling and cement production operations create significant CO2 and Greenhouse Gas Emissions. This paper introduces post-consumer glass as an alternate, equally effective and lower cost binder agent strategy for cement in backfill that may be implemented to assist in reducing solid waste production, lowering energy costs, and restricting Greenhouse Gas Emissions. Extensive engineering testing, consisting of pipe flow loop tests and strength tests, has been implemented in order to demonstrate the technical feasibility of process integration within industry. An economic analysis has demonstrated that glass is competitive in cost relative to cement and a socioeconomic study has further indicated that the utilization of glass in mine backfill would create a new market for waste glass that requires less processing and reduces costs."

Jan 1, 2005

By Norman K. Olson

Hard-rock phosphate was formerly the chief source of all phosphate in Florida. Its mining began as early as 1883 or 1884, reached a peak level in 1907 and ceased in 1966. Production began and ended in the Dunnellon area (Marion County). Nearly all the hard-rock was exported because its P205 value per unit weight is generally more concentrated than that of other phosphate rock. Maximum production, achieved in 1907, was greater than 600,000 tons; the total value for that year was more than $4,000,000. The Florida hard-rock phosphate, considered to be of middle Miocene to early Pliocene age, has an intermittent narrow, linear northwest-southeast trend. The Ocala uplift controls the phosphate distribution for more than 200 miles. Other known, isolated hard-rock areas appear to be related to minor folds on the Ocala uplift. The hard-rock phosphate deposits are a heterogeneous mass of sedimentary fluorapatite, chert and quartz with textures ranging in size from clay to boulder, and in thickness from 0 to 40 feet. Phosphate compounds, principally fertilizers, have been in oversupply since before 1968, but by the middle 1970&apos;s some experts forecast a supply-demand balance. A brighter future for exploitation of Florida hard-rock phosphate depends upon one or more of these factors: 1) depletion of present premium grades (74 percent BPL and above) of land-pebble; 2) cheaper electric power from nuclear generators for profitable electric furnace operation; 3) supply and price of sulfur; 4) manageable rail-water transportation costs; 5) development of less costly mining and separation methods; and 6) minimum competition from high-grade foreign phosphate.

Jan 1, 1972

By Scott G. Britton

In this chapter, I shall discuss railroad con¬struction for modern underground coal mines. Because men, materials, and supplies are being moved more often and farther by rail, the ef¬ficient and safe construction of the system takes on new importance. Most large coal mines are opting to use track haulage over other support transportation systems because of cost, ease of installation, reliability, and other factors. En¬gineers tackling the problem of designing such a transportation network must be aware of all the steps required for an effective transportation system design. This chapter discusses all aspects of efficient trackwork construction. The areas covered in¬clude design factors, laying the track, installing turnouts and switches, and installing trolley wire. Each area includes a description of the steps needed to complete the work.

Jan 1, 1983

By R. B. Steele

The paper contains the results of the physical and mathematical simulations (based on the finite elements simulation) of the length and shape influence on the mechanical strength of the brex. Key words: Stiff extrusion, extruded briquettes, BREX, mechanical strength, cold strength, compressive strength, tensile splitting strength, oval shape, finite elements simulation. INTRODUCTION Extruded briquettes (BREX) exhibit a set of unique properties when compared with briquettes formed by alternative methods. Brex generally have sufficient integrity right after extrusion to withstand the necessary handling and stockpiling and does not require any special means and tools for the green briquettes strength conservation. In a typical die without an ancillary cutting device green brex tend to have very high length to diameter (L/D) or length to section area ratios. For round hole dies the brex are typically 5to 6 times the diameters and even longer. Stiff-extrusion allows also for the very easy changing of the forming dies. Dies with different cross-sectional shapes of the brex (round, ovals, square, hollow structures and many other two dimensional shapes) are possible, and common. The results of our investigations show how these geometrical shape factors contribute to overall quality of the brex both in terms of strength and as new charge components in metallurgical furnaces and processes [2-4]

Feb 27, 2013

By C. Cigna, M. Patrucco, D. Savoca, E. Lovera

The paper deals with the activity program and the preliminary results of a research work commissioned by IReR Research Centre and Regione Lombardia to the Department of Land, Environment and Geotechnologies of Politecnico di Torino. The aim is to define measurement, analysis and control criteria for the emission of chemical and physical pollutants from non-metal mining industries, with particular reference to noise and airborne particulates. Such emissions are related to health risks and annoyance problems, both for the working crews and the neighbouring population, and so, in order to get an effective sustainability of the industry, suitable reduction methods and assessment tools are required. A simple technique for the evaluation and forecasting of both the emission levels and deriving impact has been tested at different mining and quarrying sites, considering their differences in terms of layout and exploitation method, the latter ascribed to a series of main typologies as present in Lombardia region.

Jan 1, 2005

By R. T. Webber, D. Moffett, D. W. Averill, G. H. Kassakhian

INTRODUCTION In Canada, radium-226 is removed from uranium mining and milling effluents by the addition of barium chloride to precipitate barium-radium sulphate. Large settling ponds are provided to effect solid-liquid separation. However, the barium-radium sulphate precipitate [(Ba,Ra)S04] is a fine, slow-settling crystalline solid which is not easily removed by simple sedimentation systems. Consequently, settling pond effluents may contain appreciable quantities of particulate or suspended radium-226, depending upon the specific pond system and/or the time of year considered. Also, current technology is expected to be incompatible with ultimate disposal goals since safe recovery of the barium-radium sulphate sludge from the settling ponds may be difficult to achieve (IAEA, 1976). Under the auspices of Environment Canada, a Government-Industry Mining Task Force established a Radioactivity Sub-Group in 1974 to assist in the development of effluent regulations and guidelines for the uranium mining industry. Among the recommendations of the Sub-Group was the need to seek more effective methods of radium removal, including development of physical--chemical treatment systems as an alternative to settling ponds. In response to the Sub-Group recommendations, a bench scale feasibility study began in March 1976 at the Wastewater Technology Centre (WTC) of Environment Canada. The bench scale work was expanded and accelerated in 1977 with financial assistance provided by the Atomic Energy Control Board. The results of this study indicated that coagulation and flocculation of the (Ba,Ra)S04 precipitate greatly increased settling rates (Wilkinson and Cohen, 1977). Subsequently, a research program with a larger scope was initiated in January 1978; this program is jointly managed and funded by government and industry as indicated in Table 1. The principal goal of the Joint Government-Industry Program is the development of a physical-chemical process to reduce the radium-226 content of uranium mining and milling effluents. The following effluent radium-226 activities were established as targets for the program: 0.37 Bq/L (10 pCi/L) as total radium-226; 0.11 Bq/L (3 pCi/L) as dissolved radium-226. Process development work was undertaken at bench scale at the WTC and at

Jan 1, 1980

By Curtis A. Pledger, H. Lee Wimmer, I. Michael Gowring

The Upper Diamond Fork Project, as part of the Central Utah Project Completion Act, conveys water six miles from the existing Sixth Water Aqueduct to the Diamond Fork Pipeline. During design, a Value Engineering team proposed a single-tunnel alignment that would be less destructive on the environment and might have a lower life cycle cost than the proposed design of two tunnels connected by two pipelines on steep hillsides. A decision was made to include this option in the bid process as a design-build alternative. The bid for this option was the lowest and a contract was awarded. During the TBM excavation a segment of tunnel wall caved in containing large quantities of water saturated with extremely high levels of hydrogen sul?de (H2S)gas (measured at 380 to 520 ppm in the air). The Central Utah Water Conservancy District (District) in consultation with Obayashi/Clyde (Contractor) quickly developed anew plan to finish the system by incorporating parts of the original tunnel/pipeline concept and re-bid the remainder of the project as a Phase 2 Design-Build contract.

Jan 1, 2003