Search Documents

By Eberhard Werner

Existing reports on the effects of mine subsidence on water wells and springs appear to be inconsistent. Some report quick and complete recoveries to pre-mining conditions while others indicate long-term or permanent effects. It is clear that topographic and geological factors as well as precise position with regard to the mine are important in determining probable effects of subsidence on aquifers. Ridgetop aquifers which are well above regional base-level are much more susceptible to disturbance by mining activities than those located topographically lower. Effects seen are attributed largely to increased permeability, both horizontal and vertical. of the aquifer rocks. The deeper aquifers usually show short term losses or water-table declines. but the effects on the ridge-top aquifers persist for longer periods or may be permanent. Subsidence enhances permeability. so that infiltrating water moves much faster to lower levels. causing pond and stream losses and declining levels in wells as well as declining flows of springs of the higher aquifers, while increasing levels and flows of the lower aquifers. Additional effects are shifts of spring locations caused by minor tilts due to differential subsidence and redirection of shallow flows by changes of horizontal fracture permeability. These effects are seen as mining of a panel progresses beneath the site. and are often repeated when adjacent panel mining fronts pass the site. Analysis of water well level and spring flow records indicates that the effects are greatest at the edges of longwall panels in the tensional regime. These effects are amplified for locations close to topographically steep terrain and in close proximity to fracture traces mapped from medium-to small-scale aerial images.

Jan 1, 1986

By Marini David, Pigorini Andrea, Fuoco Stefano, Zurlo Raffaele

"The excavation of a tunnel in highly weathered and strongly fractured rock masses due to tectonic actions is still a challenge. In order to maintain reasonable productivity, excavation through a wide zone of highly tectonized rock mass requires a detailed, integrated study of the construction solutions and a monitoring system to minimize the process time and to optimize the adopted consolidation measures in accordance with a predefined matrix of possible support systems. This paper summarizes some interesting data acquired during the excavation of the Brenner Railway Base Tunnel system between Italy and Austria. The Brenner Base Tunnel (BBT) runs through the fault line between the European and the African tectonic plate. This big fault zone is called “Periadriatic Line.” In particular, data acquired in the exploratory-service tunnel have been analyzed. Furthermore, the base concepts for defining the consolidation and support solutions adopted for the excavation of the exploratory tunnel are described. INTRODUCTION The Brenner Railway Base Tunnel (BBT) is a system of underground structures and tunnels that is designed to connect Italy and Austria using new railway standards. It is based on high speed (HS) concepts and applies the European Standards for Interoperability (TSI). The railway includes twin tunnels for a total length of about 55.0 Km without considering the connection tunnels to the existing underground railway in Innsbruck. Including the latter, the total length of the tunnel system reaches 64 Km, and is among the longest tunnels in the world. The Italian section passes through the so-called ""Periadriatic Line,"" which is an important tectonic structure generated by the collision between the European and the African tectonic plates. Despite the extensive investigations carried out (boreholes down to 700 meter depth), significant geological and mechanical uncertainties inside the Periadriatic formations remained unsolved. In order to elevate the level of confidence and observe the behavior of the rock mass at a representative scale, the BBT Authority decided to excavate in advance the service tunnel, which has taken the function of an exploratory tunnel. The data and observations collected during its excavation would provide important insights for the design of the main tunnels."

Jan 1, 2016

By Ronald E. Yarbrough

As a result of concern for the citizens of the State of Illinois who owned structures above underground mine workings, the Illinois State Legislature passed House Bill 158 in 1978. This bill amends the Illinois lnsurance Code and creates the Mine Subsidence Reinsurance Fund which is an insurance pool that is to receive a state appropriation of $500,000 as "start-up" money. One hundred thousand dollars has been paid to the fund as of October, 1982. The Fund is to return this appropriation to the State and is to remain self-supporting from premiums. The Fund utilized a pre-existing institution, which also was an insurance pool, the "Fair Plan Facility" and its governing Board, consisting primarily of insurance executives, to administer the program. The Mine Subsidence lnsurance Act went into effect October 1, 1979, and the bill provides that property owners in the State of Illinois may purchase up to $50,000 of mine subsidence insurance which is attached to their fire insurance policy. The deductible is normally 2%, but cannot be less than $250 or more than $500. The annual rate structure for residential structures in 1981 for $50,000 coverage is $10 (frame), and $12 (masonry). The rate structure for commercial buildings is based on the value of the building and the rates for $50,000 maximum coverage is adjusted upward. The insurance was mandated by the State Department of lnsurance and rolled onto the insurance policies of the homeowners in 34 counties which had been recognized as having sufficient exposure to subsidence damage to be covered by the Act. One percent or more of the land surface is undermined in each of the 34 counties. In the other counties undermined in the State of Illinois, insurance is available to the homeowner upon request to the private insurance carrier.

Jan 1, 1982

It took me nearly nine months to make the move from Arizona to Berkeley, opening an office and planning our new home. While I was in Warren Dorothy had rented two rooms for my office In the new California Commercial Union Building at 315 Montgomery Street in San Francisco. She made such a good choice that this remained my address for more than 50 years Dorothy had also looked over many lots In Berkeley, and took an option on the one that pleased her the most. It was a beautiful lot, or rather three, as we took three lots to protect our view. The only possible drawback was that it was in a new district and there were only two houses within two blocks. No one could tell how the area would develop but we liked it so much that we bought the lots on the spot and signed a note to guarantee payment. Dorothy's good judgment was shown by the fact that after 50 years we are still glad to be living on the same property, at 168 Southampton Avenue. We arranged a meeting with the distinguished architect Bernard Maybeck-and employed him to design a house for us. Dorothy spent most of her time with Maybeck planning the house and an attached studio for her, and she later wrote an amusing essay on her dealings with Maybeck. They were so successful that even now we could not think of any changes we would have wanted. It took several months to design a house that suited Dorothy and would fit on our hilltop. I was glad to overcome some of Maybeck's scorn for "only an engineer" by showing how, by rotating the studio addition 45º, it would fit the lot without serious excavation. We finally signed a contract with Maybeck, borrowing so much money that it scared us. First Consulting After short jumps to the gold mines in the Secret Pass District near Kingman, Ariz., and to the Espiritu Santo prospect adjoining the rich

Jan 1, 1976

By Young C. Kim

Because of the high cost of obtaining coal washability samples, it has been difficult to obtain washability variograms in the past. As a result. It could not be determined if geostatistical prediction tool known as kriging can be applied to predict in-situ coal washability characteristics.

Jan 1, 1988

By G. C. Van Bever, J. J. Zaluski

Introduction The Surface Mining Control and Reclamation Act (Public Law 9587) (hereinafter the "Act" or "SMCRA") passed by Congress in August 1977 represents a comprehensive federal scheme for controlling surface coal mining and the surface effects of underground mining through permitting requirements, performance guidelines and reclamation planning. While the provisions of the Act have been the subject of numerous legal challenges and court battles over the years, it is difficult to identify a more controversial program within the Act than the provisions for designating lands as unsuitable for surface coal mining operations. The lands unsuitable designation process provides for the acceptance and review of petitions submitted by citizens or organizations seeking to have specified land areas designated unsuitable for all or certain types of surface coal mining activities. In filing these petitions, the interested parties or petitioners are required to make allegations about potential adverse impacts on people or the environment and submit evidence supporting their allegations. In 30 U.S.C. § 1272, Congress provided that "[a]ny person having an interest which is or may be adversely affected shall have the right to petition ... to have an area designated as unsuitable for surface coal mining operations." Under the Act, an area can be designated as unsuitable where the mining operation will (1) be incompatible with existing state or local land use plans, (2) affect fragile or historic lands, (3) affect renewable resource lands where mining operations could result in substantial loss or reduction of long-range productivity, or (4) affect natural hazard lands where such operations could substantially endanger life and property. In enacting SMCRA, Congress mandated that each state establish a process to determine which, if any, lands within the state are unsuitable for all or certain types of surface mining operations. In response to this federal legislation, the Kentucky General Assembly adopted a state regulatory program for surface mining that included provisions direct¬ing the Secretary of the Natural Resources and Environmental Protection Cabinet to establish a program for designating lands as unsuitable for surface mining as required by the Act. In recent litigation in Kentucky, several environmental groups filed a lands unsuitable petition, later joined by the University of Kentucky, challenging a proposal by Arch Mineral Corporation to surface mine over 3 million tons of recoverable coal. The petition sought to designate over 10,000 acres of land adjacent to Arch's proposed operations as unsuitable for surface mining operations, basically alleging that the mining would disturb an outdoor laboratory. The filing of the petition activated Kentucky's regulatory scheme for reviewing lands unsuitable petitions that can result in an absolute prohibition against surface mining on the petitioned land for historical, environmental and other related reasons. The designation process involves vague petition requirements creating a situation that Arch argued is devoid of constitutional due process and subject to abuse by the petitioner on many fronts. Arch maintained that the lands unsuitable regulations do not grant adequate protection to Arch's legitimate property rights under the due process clauses of the United States and Kentucky Constitutions and are thus void and unenforceable. The entire process resulting in a decision on the petition took just under 12 months in the Arch case, and although Arch was ultimately successful in preserving its right to mine, Arch's surface mining permit was held up for this period of time. This delay led to the cessation of mining operations by Arch and the idling of over 250 workers. This paper will review the lands unsuitable designation process and the significant implications the process has for existing surface mining operations, currently proposed operations and even those long-range operations not yet contemplated. Special emphasis will be given to Kentucky's lands unsuitable program. Finally, the recent litigation involving Arch Mineral Corporation and its effort to surface mine 81.5 acres of Arch controlled property will be utilized to illustrate this very unusual regulatory scheme. Regulatory background Chapter 30, Subchapter F of the Code of Federal Regulations (C.F.R.) promulgated to implement the provisions of SMCRA, requires that each state establish procedures under the state's surface mining program for designating non-federal and non-Indian state lands as unsuitable for all or certain types of surface coal mining operations. 30 C.F.R. § 764.1. The C.F.R. establishes minimum standards for state lands unsuitable programs and sets out requirements for filing a Lands Unsuitable Petition (hereinafter "LUP"), processing LUPs, decision-making guidelines and hearing requirements. Kentucky has adopted regulations providing for the implementation of the lands unsuitable process as part of the state's regulatory program under SMCRA. The following discussion summarizes the principle components of the Kentucky lands unsuitable program.

Jan 1, 1993

By Chas. F. Jackson

INTRODUCTION This paper is one of a series dealing with mining methods and costs, prepared and published under the sponsorship of the US Bureau of Mines (USBM) and made possible through the cooperation of many mining companies in the US and foreign countries. The data presented have been obtained from papers previously published by the Bureau dealing with indi¬vidual mines, from the technical press, and from infor¬mation furnished by the mining companies. DEFINITIONS Top Slicing The term top slicing is commonly applied to that method of mining in which the ore is extracted by a series of timbered slices, beginning at the capping; the slice is caved, bringing down the capping to the floor of the slice; the succeeding lower slices are mined up to the overlying mat or gob, consisting of an accumulation of timber from the upper slices and broken capping, which follows the mining progressively downward (Fig. 1). The term has also come to be applied to the mining of ore bodies only one slice thick, by a series of tim¬bered slices one beside the other. The timbers are blasted out, bringing the capping down to the floor, suc¬ceeding slices being driven alongside those already caved (Fig. 2). In USBM classifications of mining methods, top slic¬ing has been placed under the heading caved stopes. The method differs fundamentally, however, from the cav¬ing methods of mining in which the breaking of the ore itself is accomplished by caving action induced by undercutting. In top slicing the ore is broken by the ordinary methods of drilling and blasting, and only the capping is broken up by caving. Main Levels or Haulage Levels Main or haulage levels are the main extraction levels on which the ore is hauled to the shaft. These levels and the shaft constitute the preliminary development of the mine.

Jan 1, 1982

By R. K. Mehta

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated for a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1989

By James M. Barker, Richard O. Y. Breese

The recognition of perlite as a distinct volcanic glass, and of the arcuate fractures that often characterize these natural glasses, dates back at least to the late 19th century and perhaps into the 18th century (Howell, 1974). Some authors suggest that recognition of perlite dates considerably further into antiquity, perhaps to the 3rd century BC (Caley and Richards, 1956). Most recent definitions identify perlite by the presence of vit¬reous, pearly luster and by the presence of characteristic concentric or arcuate perlitic fractures. As discussed more fully below, arcuate fractures in perlite need not be megascopic. The textures of perlite which commonly occur in deposits range from dense to highly vesiculated to pumice-like. Thus, the classical definition of perlite is descriptively restrictive compared to the natural range of textures and neglects to address the issues of genetic origin and geologic occurrence. In spite of the petrological usage of the term perlite, the in¬troduction of expanded perlite aggregate into industrial markets caused the term to be applied as well to the lightweight, cellular aggregate that is produced through the rapid thermal expansion of milled perlite ore. Perlite is distinguished petrologically from other natural glasses by a silicic or rhyolitic composition by the presence of 2 to 5 wt% total chemical water held within the glass structure and often by the presence of pearly luster and onionskin-like perlitic fractures. Worldwide, occurrences are associated with Tertiary through early to middle Quaternary volcanics and with the glassy portions of silicic domes and flows, with vitric tephra, with the glassy chill margins of dikes and sills, and with the glassy portions of welded ash flow tuffs. Less commonly, perlite is reported in association with the glassy portions of volcanic plugs and lacco¬liths. The perlite carapaces that partially or fully comprise extru¬sive domes and flows are often thick and areally extensive, and thus provide commercially attractive targets for low cost open pit mining. Perlite tuffs and tephras are also important commercial sources. Mining costs are minimized by open pit quarrying and by either bulldozer ripping or blasting. Crushing and sizing facilities are generally close to the pits. Due to the low weight and large volume of expanded perlite, unexpanded perlite that has been crushed and sized is usually shipped nationwide directly to local markets where it is expanded and processed for distribution to end users. The vast majority of international trade is in unexpanded perlite. In the United States, the evolution of the expanded perlite industry can be traced to the late 1930s and early 1940s when expanded perlite aggregate was introduced into gypsum plaster and concrete markets as a substitute for vermiculite (Schundler, Jr., oral communication, 1991) and was promoted for use in a much broader spectrum of products (Howell, 1974). By the early 1950s, end user markets were well established and small expanders were numerous east of the Mississippi River. Today, mining and expan¬sion is undertaken throughout the world. Worldwide production of perlite is dominated by the former Soviet republics, the United States, and Greece. Total worldwide production of processed perlite during 1990 is estimated at roughly 1 778 000 tons (Davis, 1991). The physical properties of expanded perlite that give this prod¬uct unique commercial value include: low bulk density, chemical inertness, high insulating ability, nonflammability and fire resis¬tance, and its ability to retain water. These and other physical properties give expanded perlite value in such uses as: lightweight acoustical and thermal insulating aggregate; component in plaster, insulating cements and lightweight concrete; loose fill insulation; as aggregate in horticultural applications; and in milled form as filter aid. In the United States and Europe, the largest end use is within building construction products.

Jan 1, 1994

By Allan M. Johnson

Since 1974 researchers at Michigan Technological University have been studying mine subsidence in the Iron River District of Northern Michigan. The district, which was active from 1881-1978, has had numerous cases of subsidence. Much of the subsidence resulted from rock mass failure but some appeared to have developed primarily in the thick glacial overburden which is a typical feature of this area. This latter observation led to the recognition that some of the surface subsidence was due to piping; i .e., loss of overburden material to the mine voids by groundwater flow (Johnson and Frantti, 1978). The Sherwood Mine was the last mine to operate in the district. With its closedown scheduled for late summer of 1978, a unique opportunity to monitor the mine as it flooded was presented. It was reasoned that with the cessation of pumping, groundwater would rise in the overburden and the mine would flood. The physical characteristics of the mine were favorable for piping to occur as the mine flooded. With the permission of Inland Steel Mining Company and the support of the U. S. Bureau of Mines, a project to monitor the Sherwood Mine for piping subsidence began in June of 1978. This paper present aspects of this study pertinent to the piping-induced subsidence events which occurred at the Sherwood Mine in 1980 and 1981, including acoustic emission monitoring of the subsidence activity, hydrologic monitoring of the groundwater regime and the flooding mine, laboratory modeling of the piping mechanism, and analytic procedures which are under development.

Jan 1, 1982

By John L. Schroder

The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are : 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same seam in nearby properties. Such mines may indicate in advance much about roof control, drainage, ventilation, and other mining problems.

Jan 1, 1981

By F. N. Earll

4.1 – DEFINITIONS 4.1.1-MINERALS, ROCKS, ORES AND NONMETALLIC MINERALS F. N. EARLL A mineral is a naturally occurring inorganic element or compound. Most minerals are distinctly crystalline in habit, and many commonly occur in well-formed crystals or crystalline aggregates, but a few species are characteristically amorphous or noncrystalline. Nearly 2,000 mineral species are now recognized but, perhaps fortun¬ately, a rather large proportion are rarely encountered. Even so, the application of modern mineral-detection and identification techniques reveals the presence of surprising numbers of mineral species, even in deposits of outwardly simple mineralogy. A rock is an aggregate of grains or crystals of one or more minerals. Some rocks are essentially monomineralic. Thus, limestone consists largely of the mineral calcite, and many sandstones are dominantly quartz. Most rock varieties, however, contain a number of mineral species, and their classification or identification depends upon the minerals present, their relative abundance, and such factors as rock tex¬ture and origin. Ore is defined as an accumulation or deposit of one or more minerals that can be exploited at a profit. The profit criterion commonly is taken somewhat liberally, however, for, although always present, the specific mineral content that constitutes a viable product is transitory. The term ore, usually, but no longer consistently, is restricted to the description of mineral deposits that are of value for their metal content. Nonmetallic deposits, although similar to metallic ores in many respects, generally are valued for the minerals or compounds present, as with rock salt (halite), rather than for individual contained elements, though such minerals as elemental sulfur are of much value. 4.1.2-ROCK TYPES F. N. EARLL Rocks arc grouped tinder three broad headings: (1) igneous rocks formed by the crystallization of magma; (2) sedimentary rocks formed by surface processes of weathering and deposition; and (3) metamorphic rocks, which may have been derived from either of the foregoing, but have undergone important physical and/or chemical changes through the application of heat or pressure, or both. The three groups can he further subdivided for convenient reference. Thus, igneous rocks are described as being abyssal or plutonic if formed at great depth, hypabyssal if formed at intermediate depth, and extrusive or effusive if formed at or on the earth's surface. The sedimentary rock group is similarly subdivided into clastic sediments and chemical precipitates. The clastic sediments form by deposition of preexisting minerals that were released from their place of origin by weathering and were transported to their point of deposition as discrete grains

Jan 1, 1973

By A. K. Bhowmick

Size reduction is very energy intensive and is the single most power-intensive operation in mineral processing plants. Research has shown that only a small part of the energy is utilized efficiently. One of the major thrusts of all equipment manufacturers has been to improve this efficiency. Choosing the right equipment to maximize energy utilization in any comminution application has always been the utmost criteria. Due to the high energy cost and depletion of good grade minerals, it is becoming essential to optimize all the subsystems within a given comminution system for the overall economic success of such ventures. Bradley Pulverizer Company of Allentown, Pennsylvania recognized this and started offering its Feeder Controller in 1988 for automatic feed control. After its first successful operation, Bradley made this as a part of all of their grinding system standard offering. It was also recognized that the Feeder Controller was just a beginning and more automation and controls would be required for an overall, efficient grinding system.

Jan 1, 1993

By Y. B. He

The effect of the stability and rheological properties of magnetite dense medium on the separation performance of a 6" dense medium cyclone (DMC) is studied with the use of fine density tracers. The tests in which different size fractions of magnetite are used to prepare the dense media reveal that at low medium densities (<1.5 s.g.), the best separation is achieved when using the magnetite with intermediate particle sizes (du3.2=18 11m). At medium densities above 1.5 s.g., however, it is beneficial to use coarser magnetite. With the fine magnetite dense medium, an increase in medium density results in a decrease in separation efficiency. With the coarse magnetite, an opposite trend is observed; the separation efficiency is improved with increasing medium density. An accurate cutpoint control is critical in gravity separation. The cutpoint shift for coarse feed particles is found to decrease with increasing medium stability (density). It assumes values close to zero in a highly stable fine dense medium. When the size of the treated particles is small (<0.5 mm), the cutpoint shift is mainly determined by medium rheology. With increasing medium density, a continuous increase in cutpoint shift is observed.

Jan 1, 1993

By T. Stack, C. Roos, M. Drake, P. Conrad

"This paper presents the evaluation Montana Tech completed for the Western Energy Company Rosebud Mine relating to the benefits of survey data collected using novel technologies over traditional methods for topographic surveys. These technologies include Unmanned Aircraft Systems (UAS), photogrammetry, and laser scanning/LIDAR. Utilizing these technologies, large areas such as reclamation areas and cast blasts can be surveyed in a timely manner for use by the mining operation. The areas that were evaluated were the improvements in the safety of employees and the time required to collect data. In addition, there is also a potential cost savings for the operation, all while not affecting the accuracy of the data that is collected. PROJECT BACKGROUND Accurate topographic survey data is critical to successful surface mining operations. It is used for mine planning and design as well as permit compliance. Currently, employees typically collect survey data using GPS equipment or total stations. These methods can be dangerous, as they require employees to work near large operating mobile equipment, edge of high walls, and on piles of stacked steep-sloped loose material. Aerial and satellite photographs, performed by a contractor, can be used to obtain some of this information, but it is expensive and may not be attainable during overcast conditions. Montana Tech, along with the Rosebud Mine, conducted research on the accuracy, cost, and other benefits of survey data collected using novel technologies. Some of the methods studied include, but are not limited to, Unmanned Aerial Systems (UAS) or Vehicles (UAV), photogrammetry, and laser scanning. These methods were evaluated to determine if these technologies provide mining companies with a safer, cost effective, and accurate method to collect data for surface mining operations. The project scope was to evaluate various surveying techniques to determine which techniques would be applicable for the Rosebud Mine and complete a trade-off study comparing the new techniques with currently used methods. The trade-off study included an analysis of the technological differences between the methods, safety and legal considerations for the new techniques, operational limits, and the costs associated with each technique. Working with the Rosebud Mine team, techniques were selected for field trial and accuracy comparison. This paper presents a literature review of applicable technical papers and a summary of the Federal Aviation Administration regulations for UAS, followed by a study comparing conventional GPS topographic surveys with UAS based systems and laser scanning systems. The comparison of the various methods was broken into the following four categories: operator safety analysis, time comparison, survey accuracy, and cost analysis. After all of these portions of comparison were completed a recommendation was provided based on the evaluation that was performed."

Jan 1, 2017

By B. K. Baird

The application of cutoffs during and after pit optimization is examined for a lower-grade multi-metallic copper deposit. Pit optimization requires calculation of the net revenue associated with each mining block, incorporating parameters such as metal prices, grades and expected recoveries, mining and processing costs, smelting and refining charges, and penalty element and royalty charges. Sensitivity analysis during pit optimization reveals which of these parameters have a significant effect on the total contained resource tonnage and total contained non-discounted revenue in the optimized pit. The cumulative effect of changing several of the more significant parameters is investigated. Application of a copper cutoff grade to a block inside the optimized pit could result in the less than optimal extraction of the resource. A block with copper grade below the applied cutoff could be economic due to the presence of other metals. Conversely, a higher copper grade block may be sub-economic. The relative merits of applying a copper grade cutoff, "equivalent grade" cutoff and dollar value per ton cutoff to blocks inside the optimum pit are discussed.

Jan 1, 1999

By Richard H. De Voto

The Pb-Zn-Ag deposits within the Lower and Middle Paleozoic strata of central Colorado (Leadville, Gilman, Aspen, and others) occur principally in Late Mississippian karst-solution features within dolomites and, to a lesser extent, limestones. Several un- conformities within the Devonian and Mississippian carbonate rocks and the subregional dolomitization of the Leadville (Mississippian) Formation that occurred during the Late Mississippian resulted from recurrent uplift of elements of the Ancestral Sawatch, Gore, and Front Range areas within central Colorado. Uplift of these areas also strongly influenced the details of the extensive karst topography that developed during the Late Mississippian. In particular, uplift of the Sawatch Range area caused paleovalleys from 300-600 ft deep to form on the karst landscape. The pattern of karst-solution caverns, sinkholes, cutters, channelways, and breccia-rubble zones was strongly controlled by incision of surface drainages and the strong northeast-trending Mississippian joint system. These subterranean karst-solution features and breccia-rubble soil [ ] zones are the primary controls of the location of the Pb-Zn-Ag ore deposits in these rocks. In the Leadville and Aspen districts, the deeply incised paleovalleys occur immediately adjacent to the principal areas of mineralization. Pennsylvanian deposition of a thick terrigenous and evaporite sequence occurred within central Colorado in response to actively subsiding extensional basins and adjacent high-relief uplift areas. Hot brines developed within the Pennsylvanian strata, migrated laterally to, and moved upward vertically along, basin- margin faults during continued Pennsylvanian subsidence and deposition. These metal-rich brines migrated into karst-solution features within the Lower and Middle Paleozoic dolomites and limestones, principally within the Leadville Formation, in basin- edge uplifted locales where the Pb-Zn-Ag minerals were precipitated. Field relationships, mineral assemblages and paragenesis, fluid-inclusion data, and isotope studies suggest that the metals and brines were derived within the Pennsylvanian sedimentary sequence and that the ore minerals were deposited under different temperatures and at different depths from deposit to deposit. Chemical reaction with the carbonate cave sediment and wallrock, cooling of fluid temperatures, and mixing with meteoric ground waters were the probable combined causes of mineral deposition in the karst-solution features. Late Cretaceous-Tertiary intrusive activity has subsequently modified some of the primary Pb-Zn-Ag deposits in local areas.

Jan 1, 2013

By L. R. Duncan, W. H. McCracken

Magnesium is the eighth most abundant element in the earth&apos;s crust and the third most plentiful element in seawater. It is found in more than sixty minerals and in brines and seawater as a magnesium salt. One of the more important magnesium minerals is magnesium carbonate, MgCO3, with a theoretical maximum magnesia, MgO, content of 47.6%; this carbonate form represents the world&apos;s largest source of magnesia. The next most used sources for magnesia are magnesia-rich brines and seawater, where it occurs as magnesium sulfate and magnesium chloride. Other commercially important magnesium-bearing minerals are dolomite, CaMg(CO3)2, which serves the aggregate industry as well as the chemical industry; brucite, Mg(OH)2, which is used in the production of both caustic and sintered magnesia; olivine, ([MgFe]2-SiO2), which serves the refractory and heat storage industries; talc, (H2Mg3(SiO3)4), which serves several industries as a filler and as an ingredient in cosmetics; and serpentine, (H4Mg3SiO9). All these minerals are of commercial value because of the desirable characteristics given to them by magnesia and by its placement in the crystal structure. These minerals are the starting raw materials for a wide range of products. These include the production of magnesium metal, and several grades of magnesia used for the production of both sintered magnesia for refractory manufacture and lighter fired caustic magnesia, the latter is used in fluxes, fillers, insulation, cements, decolorants, fertilizers, chemicals, in the treatment of waste water including pH control, and in the removal of sulfur compounds from exhaust stacks. Magnesite is one of several major minerals possessing a dual character, i.e., non-metallic industrial mineral because of its principal end use as a calcined/dead burned raw material in non-metallic end products and magnesium metal. A large percentage of the magnesia used to produce magnesium metal comes from seawater1 brines. The total primary metal production worldwide is about 350 ktpy. This report reviews magnesite solely as an industrial non- metallic raw material. Magnesite for most refractory purposes must have a content of sintered magnesia above 85%, with a preference for those sources that have the potential for 90 to 98% magnesia values. Dolomite, used in large tonnages because of its physical properties in the construction industry, also has a use in the chemical and the refractory industry. In its calcined form, dolomite is used as a slag addition in the making of steel, and it is used in a high-purity calcine to precipitate magnesium hydroxide from brines or seawater. The precipitated magnesium hydroxide is intermediate for the production of deadburned clinker for refractories and the production of magnesium metal. In many cases the high-purity magnesium hydroxide obtained by precipitation with calcined dolomite, or in some cases limestone, has supplanted much of the world&apos;s production of magnesia from the natural mineral magnesite. This is especially true of the United States and in major industrialized areas of Europe and Japan. The best known of the minerals directly and widely exploited for its magnesia content is magnesite (MgCO3), one of the calcite group of rhombohedra1 carbonates, which includes calcite (CaCO3), siderite (Fe2CO3), and rhodocrosite (MnCO3), among others. The members of this group enter into a wide range of substitutional solid solutions when the positive ions have similar radii. The radii of magnesium and iron ions are within 6% of each other; hence magnesite and siderite form a complete series, of which the mineral breunnerite (ferroan magnesite) is a well known end member. The radii of calcium ion is 36% larger than that of magnesium ion and only limited substitution exists at each end of the MgC03-CaCO3 series. Dolomite is not a member of the calcite group, but it occurs when calcium and magnesium ions alternate in equal number in an ordered structure among carbonate ions. The result of this relationship is that calcite and dolomite are commonly found intermixed with magnesite. They occur, commonly, as identifiable crystal entities, which can be separated to a varying degree from the magnesite by benefication techniques. Magnesite, when pure, contains 47.8% MgO and 52.2% CO,. The pure mineral is found occasionally as transparent crystals resembling calcite. Magnesite principally contains variable amounts of the carbonates, oxides, and the silicates of iron, calcium, manganese, and aluminum. Although the genesis of natural magnesite deposits can be complex, it is distinguished in nature in two distinct physical forms, namely crystalline, (with a wide range of visible crystal sizes) and cryptocrystalline, sometimes referred to as amorphous, where the crystal size is not detectable to the eye and will range from 1 to 10 pm. The two types not only differ in crystal structure but in the sizes of the deposits and in modes of formations. The crystalline form has a Mohs hardness of 3.5 to 4.0. The color range is from white to black with shades of yellow, blue, red, or gray. The color is not a significant indicator of purity but in a given deposit an experienced person can often roughly grade the magnesite by observing color and crystallinity. Macrocrystalline deposits occur in relatively few, but generally large, deposits on the order of several million tons. The ore shows a marble-like crystal structure and belongs to the sedimentary or metasomatic groups of origin. The cryptocrystalline variety of magnesite frequently occurs in many small deposits, although there are exceptions. Cryptocrystalline magnesite is typically massive with no cleavage and is sometimes descriptively called bone magnesite. The fracture is usually conchoidal, with a hardness of 3.5 to 5.0. The color is mainly white, but it can have tints of yellow, orange, or buff. Accessory silaceous minerals such as serpentine, quartz, or chalcedony are usually present. Calcium minerals are normally absent or in low concentration, this contrasting with the macrocrystalline form where calcium minerals are almost invariably present and some- times in high concentration. The specific gravity of cryptocrystalline magnesite ranges between 2.90 and 3.00, whereas the value of pure crystalline magnesite is 3.02. In actuality, the normal specific

Jan 1, 1994

By Richard L. Stein

INTRODUCTION Increasing a miner&apos;s chance of surviving a disaster requires advance planning for emergencies, adequate training of personnel, and the provision of proper survival equipment. It is extremely important that fires and toxic gases be detected early, and that warning systems such as stench, audible and visual alarms, and communications systems be provided to allow timely escape. However, situations do occur where timely warning is not provided and immediate escape is not possible, regardless of the precautions that are taken. Under such circumstances, a combination of new per¬sonal protective devices and old techniques can provide protection that is adequate to save a miner&apos;s life. SELF-RESCUE EQUIPMENT Self-rescuers are devices which provide a short-term supply of respirable air under the potentially lethal con¬ditions following a mine disaster. Functioning either as filtration devices for the elimination of carbon monoxide (CO) or as oxygen supplies, self-rescuers allow an endangered miner a limited amount of time in which to effect an escape or reach a place of temporary safety. Carbon-Monoxide Self-Rescuers For almost 50 years, filtration self-rescuers have protected miners&apos; lives following explosions or fires. Designed to eliminate carbon monoxide from inhaled air, the first of these devices was approved in the 1920s and has evolved into the two units that are approved today-the Mine Safety Appliance (MSA) W-65 and the Draeger 810. Both of these units rely on the cata¬lytic conversion of very toxic carbon monoxide to rela¬tively safe levels of carbon dioxide (CO,). As shown in Figs. 1 and 2, both of these filtration self-rescuers operate in the same manner. On inhalation, the mine air passes through both coarse and fine filters that remove the dust, preventing the dust from coating the chemical beds or entering the miner&apos;s mouth. The air then passes over a drying agent that removes water vapor; this is required to prevent the water vapor from poisoning the catalyst. Subsequently, the dried air passes over the Hopcalite catalyst, where carbon monoxide is converted to carbon dioxide. Then, the air passes through a heat exchanger that reduces the temperature of the inhaled air. Finally, the air is inhaled by the user. Air exhaled by the user passes through the heat ex¬changer and exits the device through an expiratory valve. Both units of this type are subject to certain limita¬tions: 1) The units do not protect the user against oxygen¬deficient air; when air is inhaled through this type of self-rescuer, the device only removes the carbon mon¬oxide. If the mine air contains less than 15% oxygen, anoxia is inevitable. Symptoms of anoxia include dizzi¬ness, shortness of breath, quickened pulse, and deeper and more rapid respiration while the victim is at rest. During heavy exertion such as would be expected dur¬ ing escape efforts, a 15% oxygen level can cause loss of consciousness. 2) The units do not protect against excessive levels of carbon dioxide. Available data on carbon monoxide and carbon dioxide concentrations following explosions or fires are limited, but there are indications that the carbon monoxide concentration can rise to 2% and the carbon dioxide concentration can reach 5 or 6% of the mine air (by volume). In some situations, the in¬haled air could contain up to 6 or 7% carbon dioxide. At a carbon dioxide concentration higher than 2%, breathing patterns can be affected adversely. At a con¬centration of 6 or 7%, the effects include severe respira¬tory distress, with unconsciousness resulting from exer¬tion such as that needed for escape activities. 3) The units do not protect against high inhalation temperatures. The catalytic oxidation of carbon mon¬oxide to carbon dioxide is an exothermic reaction that evolves a large amount of heat. As the carbon monoxide concentration increases, the temperature of the inhaled air also increases. Available data show that above 1.5% carbon monoxide, the air inhaled through some self¬rescuers can be as high as 90°C (194°F). At those

Jan 1, 1982

By Kadri Dagdelen

The classification of selective mining units (SMU) and the assignment of grades to those classified SMU are very important in open pit mining, especially for precious metal mining. When the classification is done, the true values of the SMU grades are unknown. These unknown SMU grades are mostly estimated analyzing the geologic data and blast hole assays. To classify the SMU&apos;s based on the estimate of SMU grade, without considering uncertainty associated with unknown SMU grade, yields incorrect decision in sending material to appropriate destination. In this paper, a method is developed to classify SMU&apos;s considering the uncertainty associated with unknown SMU grades. By using this method, traditional estimate of SMU grade is replaced with conditional probability distribution of SMU grade. The decisions about the destination of a given SMU are performed by minimizing the loss due to misclassification. Also, the asymmetric loss function by penalizing the overestimation and the underestimation unequally is used in assigning grades to classified SMU&apos;s. A case study is carried out to apply the traditional ore control techniques and proposed method in classification of SMU&apos;s and the assignment of the grades in a hypothetical gold mine.

Jan 1, 1999