Search Documents

By Jürgen Lotze

Previously (1981), it was shown that the fiscal policy practised by some IBA-member countries is mainly responsible for a significant shift of known bauxite resources into higher processing-cost categories. The possible impact of politically imposed fiscal costs on the competitiveness of relevant bauxite resources is investigated in detail by means of a model calculation procedure.

Jan 1, 1984

By Mark E. White, John H. McCowan, Michael C. Costello

Minproc Engineers has carried out the design construction and commissioning of thirty two process plants in the period 1978-87. Twenty eight are gold silver recovery plants, and of these twenty two were gold alone and six were gold and silver. In most plants carbon was used for gold adsorption. Desorption has been carried out using the USBM Homestake method, the Anglo American Research Laboratories method, and the Micron Methanol method. Electrowinning has utilised steel wool, stainless steel wool, and aluminium cathodes. Electrorefining using polished stainless steel cathodes is practised. This paper summarises the experience gained in these operations

Jan 1, 1987

By G. T. Adel, W. Z. Choi

In previous work at Virginia Tech, a population balance-model describing the simultaneous processes of size reduction and mineral liberation has been developed. Experimental verification of this model, however, has been limited to a binary mineral system containing only one composite particle class. When considering multiple classes of composite particles, estimation of model parameters becomes much more difficult. In the present work, a procedure for estimating model parameters for a multiple-composite- class model has been developed. Emphasis is placed on direct experimental determination of these parameters. The physical significance of the breakage rate function and the liberation function in characterizing the liberation process is also discussed.

Jan 1, 1987

By Allen V. Reicks, Thomas J. Rudolphi

Computerization has allowed practical design of complicated and optimized belt conveyors for bulk materials from prediction of belt tensions around the belt circuit for a wide range of belt loadings and conveyance paths. These design methods are based on a knowledge of component operating characteristics and sources of tension change. As compared to generalized 'f' methods, CEMA's historical Kx and Ky has provided nonlinear and more specific predictions of belt tension as affected by various components and operating conditions. These empirical values were developed in a different age and generalizations made in their development are now a constraint to additional conveyor improvements. This paper discusses the potential from improved and standardized ‘friction’ predictions and presents the results of sensitivity evaluations as affected by calculation method

Jan 1, 2004

By Joe M. Bryan, George E. Rodger

The development of small precious metal mines in the western states has been directed at heap leach operations. Crushing plants are an essential adjunct to heap leach operations. They must meet environmental air quality regulations which generally follow a similar pattern from state to state. Prior to mine construction a permit must be obtained and an operating permit granted during or shortly after the start-up period. The typical construction permit application consists primarily of drawings, specifications and an explanation sufficient to indicate that the mass of particulate matter entering the atmosphere is below minimum standards. The operating permit may be granted following demonstrations that air emission control equipment or methods comply with information submitted in the construction permit application.

Jan 1, 1987

By J. M. Baker

It seems appropriate here to open with a quotation from the great pre-Confucian philosopher Lao-tze: "The softest thing in the world dashes against and overcomes the hardest. There is nothing in the world softer or weaker than water, and yet for attacking things that are firm and strong there is nothing that can take precedence of it." I am happy to report that our system of mining has worked out, with minor modifications, as well or better than was predicted. This, in a period of rising labor and material costs, has been most gratifying. Gilsonite is a solid hydrocarbon which occurs in vertical fissures cutting the sandstone and shale beds of the Uintah formation in south¬eastern Utah. It is found in other parts of the world under similar occurrence but nowhere else is it now being mined commercially. The Gilsonite veins on entering the shale members of the Green¬river formation break into small veinlets separated by shale, These veinlets are not now economical to mine.

Jan 1, 1959

By B. Cavender

The operating lifetime, or production rate, selected for a mining project is among the most important factors influencing the project's design and ultimate economic success. Incorrectly-determined lifetimes can lead to the erroneous rejection of projects as uneconomic as well as the suboptimal exploitation of producing properties. This paper examines the optimal lifetime calculation using traditional discounted cash flow and recently-proposed option pricing techniques. Using each method, the production rate is determined as that rate at which the project's net present value is maximized.

Jan 1, 1993

By S. L. Huang, J. D. Rockaway, N. B. Aughenbaugh

Shale has long been recognized for its tendency to swell when exposed to the atmosphere. Interaction of moisture with exposed shale strata can cause serious ground stabi1ity problems, since the initial strength of a shale is reduced if the material is sensitive to moisture variations. In this paper, the authors present a classification system to estimate the response of swelling generated within shales. This characterization of the swelling potential is based upon plasticity, susceptibility to moisture, mineralogical constituents of clay size particles, and fabric. Use of this classification system in conjunction with other existing rock properties tests will provide data for more rational engineering design.

Jan 1, 1986

By D. E. Ranta, Neil D. O’Donnell, Thad B. Ostrowski

Ore reserve estimation at the Syncrude Canada Ltd. open-pit oil sands mine in Northern Alberta has evolved since the project's inception. Early techniques followed a conventional petroleum reservoir analysis format, with relatively widely spaced drill holes and semiquantitative grade data. Experience has developed a more standard mining approach, including classification of geological materials by both lithology and sedimentary origin, timely and multi-purpose drill holes, precise analytical data, empirical recovery factors, a computerized geological data base, and an orebody block model. Future efforts will involve enhancement of existing techniques, use of geostatistical algorithms, quantification of confidence limits, and improved control of the ore model by geological parameters.

Jan 1, 1992

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) is linked to cumulative back, neck and abdominal disorders. In low coal mines, space restrictions make it difficult for seat suspensions to isolate operators from shock and WBV. Researchers at NIOSH's Pittsburgh Research Laboratory are responding to these issues by investigating viscoelastic foams. For the full-load case, an ergonomic seat made with viscoelastic foams can isolate the shuttle-car operator from shock at 15 Hz. Researchers used results from additional foam testing using an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 2000

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states, and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies important problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2003

By B. Dabrowski, J. D. Miller, D. Halbe, J. Hupka

An air-sparged hydrocyclone (ASH) mobile system was evaluated for continuous stripping and recovery of cyanide (the AVR process) from process water at a gold plant site. The ASH unit performed exceptionally well as an absorber. HCN was removed from the gas phase in a single one second pass with an efficiency exceeding 99%. HCN concentration in the discharged gas phase was lower than 10 ppm, which provided for a safe working environment. The stripping efficiency, controlled by the Henry’s Law constant, exceeded 40% in one pass.

Jan 1, 2004

By Robert G. Moorhead

Fine-coal screening can be one of the most critical operations in a modern coal-cleaning plant. The yield and quality of clean coal produced in fine-coal circuits is controlled as much by how efficiently 0.15 mm (100 mesh) particles are sized as on the performance traits of the fine-coal cleaning device itself. In addition, the increased interest in effective fine-coal sizing operations indicates that many operators have also discovered its importance in affecting the quality and yield of clean coal produced in fine-coal circuits. This paper describes the three most prevalently used fine-coal screening technologies and discusses their sizing mechanism, performance, and application.

Jan 1, 1988

By Jin Anshi, Wang Dai, Wang Zingshen

Both fire and gas problems in Fully Mechanized Sublevel Caving Coat Face are quite different from those in common fully mechanized coal face. Pouring N2into the goaf would be the best method to prevent fire in the goaf. In this paper how to determine parameters of pouring N2 is discussed. Comparing distributions of gases and temperature before pouring N2into the goaf with those after pouring N2 into the goaf, the effectivenesses of preventing the fire by pouring N2 into the goaf are testified. Some special gas problems appear in Fully Mechanized Sublevel Caving Coal Face, which are proved to be serious and interrelated with pouring N2 into goaf. Finally, a few methods adopted to deal with gas problems are described simply.

Jan 1, 1991

By E. Alaphia Wright

An accepted approach to open pit mining sequence planning is one of computer aided planning where: the planner works out his mining sequences by trial and error using interactive graphics; This approach gives results that could in- variably be improved given more time for the planning exercise. Increased emphasis on interactive planning reveals a need for simple formalized procedures for improving mining sequence planning practices. This paper discusses a case study in which Dynamic Programming (DP) is used in mining sequence planning. It is shown that DP can be applied to identify various intermediate, pit boundaries. These are then arranged in descending order of economic values and their material contents analysed with respect to tonnages, grades, production requirements, and equipment capacities. Those increments which best satisfy defined conditions are selected and the others discarded. The mining sequence is thus built up as a chain of best- economic valued mining increments satisfying given production requirements and constraints.

Jan 1, 1989

By V. E. Ross

A model has been developed that describes the behavior of mineral particles and water in the cleaning zone of flotation columns. The possible detachment of particles from their sites of attachment at the bubble surfaces is related to the flux of bubble surface area with increasing distance from the interface between the collection and cleaning zones and the late at which floated particles are transported into the cleaning zone. The drainage velocities of floated and entrained particles are calculated from the drainage velocity of water and the properties of the particles. The effects of wash water and inhibited drainage in the froth are also explicitly accounted for.

Jan 1, 1988

By K. Gorazda

The population growth, urban and industry development cause the increased pollution with different substances, which contain phosphorus. It contributes to the increased demand for its compounds, increasing the use of its natural resources, which is considered to be the most accessible source. The forecasts regarding the world natural reserves of phosphorus deposits are saying that more than 50% of resources used currently will be exhausted within next 60-70 years (Steen, 1998). European Union formulated its goals regarding the waste management in 1990. Its main rules include prevention of waste generation, recycling, reuse of waste as the raw materials in technological processes, separate collection and optimization of final removal. The phosphorus recovery from waste is realized currently in many ways: directly from the waste water stream in sewage-treatment plant, from the sewage sludge, from animal waste, industrial waste and other emissions from industry (Przewrocki et al., 2004). According to the rules of cleaner production the waste should be treated as the source of resources for the production of products with full value (Kowalski, 1998).

Jan 1, 2005

By Richard R. Klimpel

The author was the banquet speaker at the 48th Annual MPD meeting, sponsored by the SME Colorado Minerals Processing Section, May 14-16, 1998, in Colorado Springs, CO. Here are his remarks. It has been an exciting experience to have spent 34 years involved with the process of generating patented technology eventually leading to commercialization. In today's terminology, this process is called technology transfer. I have had the unusual experience of being involved doing basic research as an inventor while also being responsible for managing new product development and commercialization. In addition, I worked for 31 years before my retirement for a large research-oriented company, The Dow Chemical Co. In 1995, the company spent more than $1 billion dollars on research and development. The last three years of my career have been spent working with a research-oriented university, The University of Florida. And I have worked as a consultant helping several companies to optimize their products and processes. It is on this cumulative experience base that the preparation of this article is based.

Jan 1, 1998

By J. A. Herbst, T. I. Martinovic, Y. C. Lo

This study was concerned with the application of a computer simulation methodology to optimize the performance of mills grinding iron ore concentrate prior to pelletizing. The methodology involves batch and plant testing, modeling and computer simulation. The analysis of grinding performance was carried out and capacity increases were predicted in the context of detailed population balance models developed for the plant ball mills. Model developnent and plant confirmation were performed using data obtained in a series of batch tests and three plant tests. From experimental data and computer simulation it was found that ball size, percent solids and classification all had a significant effect on mill throughput. Based on the findings of this study, a 12-152 increase in capacity was predicted to be available by a proper combination of ball size charge and optimum percent solids. These predictions have been confirmed by plant tests in which the recommended operating changes have been made.

Jan 1, 1990

By David I. Dr. Hoyer

The Hicom mill is a conical mill in which a ball or autogenous load tumbles within a high-intensity acceleration field. An autogenous Hicom mill with a power density of about 1100 kw/m3 and a volume of just 4 litres reduced a 50 m quartzite feed to 90% passing 38 microns at a feed rate of 160kg/h (in closed circuit with a hydrocyclone). Batch tests have identified fracture, chipping and abrasion breakage mechanisms at pebble sizes of 5 to 50 mm. The special behaviour of the load in Hicom mills was exploited to develop a novel technique for estimating steady state autogenous load size distributions.

Jan 1, 1992