Search Documents

By Matthew Spedding

The complex nature of the carboniferous measures prevailing in the U.K. has dictated the types of mining required to exploit the coal seams. Most mines in Britain are referred to as deep mines in the sense that they operate at depths of 1800 - 3000 feet. The main system of coal transport to the surface is by vertical shafts which intersect the workable seams which at times number between 4 and 5. As mining has been practiced in most of the major coalfields in the U.K. for well over 100 years, with the initial extraction of the shallower and more profitable seams, the present management have been left a legacy of indiscriminate extraction which severely hampers their efforts to maximise the mine layouts. There is no single standard design of mining layout capable of meeting the wide variety of conditions which exist in the British coalfields. Mining layouts are subject to fixed and variable parameters. In discussing multi-seam working, the main parameter must be the effect of old workings above and below the seam to be extracted. There is a distinct lack of reliable information which would enable layouts to be designed to completely avoid or control these destructive forces. The guidelines are, therefore, mostly empirical.

Jan 1, 1977

By G. Lodewijks

Today most belt conveyors used for the transportation of bulk solid materials are driven in a centralized way with all drives in one location. The dynamics of these systems has been studied since the early seventies of the previous century and are well understood. Compared to the more conventional belt conveyor system with a centralized drive station positioned at the head and/or tail of the system, a decentralized driven layout with drive stations distributed along the whole length of the belt offers a number of advantages. However, to make a decentralized driven configuration a good alternative to a centralized driven, the system designer will have to balance these benefits with the increased complexity. The full potential of a decentralized driven system can only be realized if the right balance is found between the locally applied drive force and the motion resistances occurring along the system. From previous research it was found that in a multiple driven belt conveyor system the most dominant belt behavior occurs in the belt section between the tensioning device and the first drive station. In this paper different possibilities are analyzed to improve this dominant belt response and optimize the starting behavior. This can be accomplished by changing the predescribed start up profile, starting the drive stations in sequence rather then all at the same time and altering the locations of the drive stations.

Jan 1, 2008

By Laurence M. Demers, Douglas C. Kuhn

It has been suggested that radicals on the surface of dust particles are key chemical factors in the pathophysiology which results from the occupational inhalation of coal and silica dust. In addition, oxygenated derivatives of arachidonic acid (eicosanoids) have been implicated as important biochemical mediators of mineral dust-induced lung disease through their role in bronchial and vascular smooth muscle reactivity, inflammation, and fibrosis. Therefore, we assessed eicosanoid production by the rat alveolar macrophage (AM) exposed in vitro to mineral dusts with varying surface chemical characteristics in order to determine if radicals associated with the mineral dub1 could influence the production of pro-inflammatory mediators in the lung environment. Rat AM were exposed to freshly fractured or "stale" bituminous coal dust, as well as untreated silica or silica calcined to 500°C and 1100°C. Prostaglandin E2 (PGE2) and thromboxane B2 (TxB2) levels in incubation medium were determined by specific radioimmunoassay. When AM were exposed to freshly fractured coal dust, PGE2 and TxB2 production were markedly increased. In contrast, exposure of AM to "stale" dust significantly reduced PGE2 and TxB2 production. In vitro exposure of AM to untreated silica resulted in a significant increase in PGE2 and TxB2 production compared to control. However, exposure of AM to silica calcined to 1100°C resulted in eicosanoid levels which were not significantly different from control. These findings suggest that radicals associated with respirable coal and silica particles may play a key role in the ability of mineral dust to activate AM eicosanoid production.

Jan 1, 1991

By Morgan M. Sears

In recent years, one large mine collapse and numerous smaller bump events have resulted in a renewed interest in coal bump research. With numerical modeling, the Energy Release Rate (ERR) calculation quantifies the ?release? of the gravitational potential energy of the rock mass into the environment as mining progresses. This release of energy can occur passively in the form of heat and sound or dynamically in the form of pillar bumps or rock bursts. From the initial application of a calculated energy release rate in the deep hard-rock mines of South Africa, the ERR was found to have a significant correlation with the risk or potential of damaging coal bumps or rock bursts. In this research, an ERR calculation is incorporated into the modern LaModel program to facilitate the analysis for potential coal bumps. Initially the ERR calculations in LaModel are verified using a case study of cut sequences originally modeled using the MULSIM/NL program. Then, the ERR calculations are applied to a bump-prone mine in Southern Appalachia were a number of different pillar recovery cut sequences were used in order to minimize the risk of bumps.

Jan 1, 2009

By Stéphane Servant, Jacques Ouellet, Ferri Hassani

This paper presents essentially the logistic and practical aspects involved for in situ testing of mine paste backfill with a self-boring pressuremeter. The investigation discussed in this paper is part of an extensive and ongoing research project to identify and validate an in situ testing technique for cemented mine backfill such as hydraulic or paste backfill as well as Insitu behavior of backfilled stopes. After a literature review on field testing of soils and past experiments on mine backfill in situ testing, the self-boring pressuremeter was selected as the most appropriate instrument for this task. The authors presents in this paper the technical aspect involved in a field trials that was conducted in a Canadian underground mine using paste backfill. The results of this first successful trials show that self-boring pressuremeter test can provide high quality and reliable backfill characteristics results, using analytical techniques developed for soils (Ouellet et al., 1998). The parameters obtained were: estimation of the lateral stress in the ground, the soil stress-strain response and the soil strength. The logistic and equipment required to conduct such testing underground is fully described. Performance achieved in the field and technical difficulties encountered are highlighted. Recommendations for future experiments with such instruments are given. Some potential technical improvements to better adapt this in situ testing technique to mine backfill are proposed.

Jan 1, 2001

By Steven J. Van Kauwenbergh, Talaat A. B. Lawendy

Batch laboratory-scale beneficiation tests were conducted on four high-iron phosphate samples. These samples included sedimentary ores (Tilemsi Valley, Mali and Tahoua, Niger), a sample from an igneous phosphate deposit (Matongo, Burundi), and a fine-grained phosphatic iron ore processing residue from Chile. The Matongo phosphate deposit occurs as a thick (up to 80 m) residual blanket of P205-enriched soil over solid parent rock (carbonatite and associated rock types). Although the Matongo deposit is an igneous deposit, ore from the deposit can be subjected to beneficiation treatments commonly used to treat sedimentary rocks. The beneficiation flowsheets designed to process these diverse ore types involve attrition scrubbing, size classification, and flotation. At the best flotation conditions tested, phosphate concentrates assaying 32.0%-39.0% P205 and 1.0%-1.5% Fe2O3, were obtained at 64.2%-82.2% overall P2O5 recoveries from run-of-mine (ROM) ores containing 9.2%-28.6% P205 and 5.9%-16.1% F,20,. A cleaner phosphate concentrate assaying 33.1% P205, 1.8% A1203, and 3.3% Fe2O3 at 53.4% overall P205 recovery was obtained from the phosphatic iron ore residue that originally contained 4.5% P205, 8.0% A1203, and 17.6% Fe2O3.

Jan 1, 1993

By Eivind Grøv

"INTRODUCTION Tunneling and underground excavation is related to handling of uncertainties, risks associated with geological conditions are significant and ‘unexpected geological conditions’ often claimed. This fact was brought to the table long ago, and ITA (the International Tunnelling and Underground Space Association) published its 25 Recommendations on Contractual Sharing of Risks in 1988 (Ref. 1). This public-cation constitutes an important asset to the tunneling industry in terms of being a guideline for those working with contractual issues, even today almost 30 years after being published. A more recent document is the ITIG code of practice for risk management of tunnel works from 2015 (Ref. 9). Various countries or geographical regions have their own view and tradition on risk sharing and tunnel contracts. In Scandinavia unit rates contracts are most commonly used with bid-build model, it shares risk between owner and contractor, owner retains the risk for geological conditions while contractor carries risk for performance efficiency. Rock strengthening is determined assessing rock mass quality encountered at tunnel face. Grouting is applied to stem water. Actual quantities may differ from the contract’s BoQ but a flexible contract with remuneration is installed to enable adjustment of actual quantities. Variations of quantities involve a clause to adjust construction time. Unit price contracts deals with expected and foreseen still ‘unexpected geological conditions’, if the ‘unexpected’ element results in variations in quantities. Work activities have quantities and ‘standard capacities’ for regulation of construction time. Variations in quantities are expected in tunnelling and hardly deserve the term ‘unexpected’. If truly unforeseen geological features necessitate work not included in the BoQ, then the contract must be supplemented and can be said to be inappropriate. Fixed price contracts may not provide the intended predictable cost and is as such also inappropriate in the view of a risk sharing principle, once the geological baseline proves to be incorrect. ‘Adjustable fixed price’ contracts, combining unit rate and fixed price, may prove suitable."

Jan 1, 2016

By Dong-mei Zhang, Feng Zhang, Hong-Wei Huang, Qiang Huang, Bin Ye

"1. INTRODUCTION Nowadays, many cities around the world have constructed metro tunnels to alleviate transportation pressure from rapid urbanization. In soft soil areas, metro tunnels are usually constructed by shield-tunneling method due to its high efficiency and little disturbance to environment. However, the tunnels may show significant post-construction settlement after several years of operation. Take Shanghai Metro line 2 for example, the maximum longitudinal settlement reached 160mm after ten years of operation, shown in Figure 1. When analyzing varying factors that contribute to the long-term settlement of tunnels, the effect of cyclic loading from train vibration is rarely taken into consideration for most researches only focus on the influence of leakage problems in the tunnel while neglecting train vibration induced leakage and resulting settlement. It’s true that metro tunnels from shield-tunneling method are prone to have leakage problems due to the special structural configuration. Furthermore, trains move hundreds of times inside the tunnel every day, which inevitably will cause accumulation and dissipation of excess pore pressure. When the excess pore pressure dissipates, tunnel settlement induced by train vibration occurs(Deng F H, 2007). Although researchers (Zheng et al., 2005; Wongsaroj et al., 2007; Mair, 2008; Shin et al., 2012; Zhang et al., 2012, 2015) conducted extensive numerical analysis on the relationship between tunnel settlement and relative permeability of tunnel to surrounding soil by treating tunnels as permeable media, their attention was only paid to the tunnel settlement from reduction of hydrostatic pressure in the ground, rather than from the dissipation of excess pore pressure generated by train vibration. Therefore, the influence of train vibration on the long-term settlements of metro tunnels is still not clear."

Jan 1, 2016

By A. J. P. Durham

Two low water flux test covers were placed on acid generating waste rack dumps at the Kidston Gold Mine in Queensland, Australia The climate is semi arid with distinct wet/dry seasons. The present study was initiated to develop a cover system to restrict infiltration. The design of the cover required optimization of water storage and evapotranspiration. Instrumentation was installed on both dumps to measure infiltration, moisture conditions and climatic parameters. Field measurements over the last three years indicate that both covers are performing satisfactorily. Selection of the final cover for closure is described on the basis of these results.

Jan 1, 2000

By S. D. Morrison, J. L. Watson

It is well known that the density and viscosity of a mill pulp have optimum levels for grinding efficiency, and sophisticated control loops are employed to control pulp density in industry. However, these control loops rely on a number of plant measurements, and often the input data will not permit effective determination and control of the mill pulp density. The use of a single remote pulp density measurement has obvious advantages, and it is suggested and demonstrated for laboratory batch grinding that mill noise measurements can indicate the effective density of the mill pulp. In addition, the mill noise is shown to indicate the actual effective pulp viscosity in the mill and hence permit the identification of the dynamic rheological regime existing in the mill. It is demonstrated that mill noise increases with grind time and, at any given grind time, with increasing pulp density in the pseudoplastic range. This increase in mill noise level with pulp density is interpreted as indicating a decreasing pulp viscosity. The results show that the transition from dilatant to pseudoplastic conditions within the mill, with increasing pulp density, can be identified by this increase in mill noise. When the pseudoplastic pulp started to exhibit yield characteris- tics, the mill noise fell dramatically. The technique of mill noise analysis is then used to investigate the effect of a grinding additive on the batch grinding of two ores. With a magnetite ore, the additive was shown to increase the mill noise, and hence decrease the pulp viscosity, in the pseudoplastic region and to increase the effective grinding. The molybdenite ore, however, did not show significant noise level changes and did not show improved grinding efficiency.

Jan 1, 1987

By Graham Swan, Richard K. Brummer

The paper begins by describing an underhand cut-and-fill mining concept for a 50m thick, generally tabular though irregularly shaped orebody dipping at 30 degrees and occurring at a depth of between 2300 and 2700m in the Sudbury Basin. From this, the broad design requirements of a fill system are stated. Two and three-dimensional numerical models are then described which were built to evaluate the theoretical benefits of different types of fill reinforcement. Included in this evaluation are the effects of span, fill strength, fill tightness, as well as static and dynamic loading types. Results, supported by large-scale physical models, are presented to show the significance of reinforcement on stable, undermined fill performance. Finally the paper describes work which has been done to evaluate the suitability of so-called silicated cemented backfill. This system is, in principal, attractive for deep mining applications since transportation is in the "safe" hydraulic regime, while fill water run-off, segregation and shrinkage effects are potentially eliminated in the stopes. The results from various surface and underground trial pours are reported which substantiate the proposed use of this type of backfill at depth.

Jan 1, 2001

By F. F. Peng, Z. Lu

Employing a combination of two types of polyelcctrolyte might become necessary to enhance both the settling rate of the flocs and the water clarity of a fine-particle suspension in a high-capacity thickening process. The sequence of addition, mixing, type and dosage of polymer all affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance, i.e., a high settling rate of the flocs and the deisired underflow density and overflow water clarity. The required performance can be achieved by either adjusting the pH prior to anionic polyelectrolvte flocculation or using a combination of polymer flocculant and coagulant (dual-polymer system). The dynamic thickening test results showed that only the approach using a dualpolymer system is capable of meeting the required performance. The effects of polvelectrolvte dosage, the sequence and numbers of polyelectrolyte addition, the feed concentration, the bed level and the rake speed on the settling rate, underflow percent solids and water clarity were studied in cylinder tests and in a laboratory dynamic thickening unit. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively using total suspended solids in supernatant, underflow density and capacity per unit of settling area per unit of time. The objective of this study was to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1999

By Scott G. Britton

Many times during the construction of a project, whether large or small, the engineer will become involved with management of the work and workforce. In some cases, mine management will turn over the direction and responsibility of doing the work to the engineer. Because of this, it is important to know some of the basic principles of human resource applications- among other management concerns. This chapter, therefore, looks at the fundamental principles of human resource management. Three broad discussions are presented to the reader. These are: (1) organization, communications, and responsibilities of management; (2) analysis of worker motivation; and (3) supervisory leadership. Each topic encompasses the current thinking for coal mining and mining management. Much of the information in this chapter comes from Practical Coal Mine Management, by this author and published by John Wiley & Sons, Inc., which discusses in depth many of the ideas presented here. Interested persons are directed to this text for more information on management skills.

Jan 1, 1983

By John Reilly

"INTRODUCTION Successful management of megaprojects, meaning delivery within budget, on time and according to expectations, is a fundamental requirement. Many projects have been successful, some have not. This paper reviews megaprojects1, drawn from the author’s projects over the last 50 years, with “lessons-learned” and a summary of recommendations that, if implemented, would improve megaproject management and delivery. Characteristics of these projects are summarized – including outcomes related to key factors such as politics, management, organizational structure, contracting methods, cost estimates, risk and other elements. The projects include the Washington D.C. Metro, Boston Southwest Corridor, LA Metro, Toronto Rapid Transit Expansion Program, BART San Francisco, MARTA Atlanta, London Underground and the Washington State Highway megaprojects – including the SR520 Floating Bridge and the Alaskan Way tunnel. Other projects that illustrate successful, innovative management and contracting methods include the Madrid Metro (low-cost delivery), the Sydney Northside Storage tunnel (outturn cost, alliancing) and the Lake Mead tunnel (working in partnership, risk management). KEY ISSUES A characteristic of megaprojects is that their complexity increases exponentially with size (Reilly 2010, Galloway et al. 2012). These projects are very visible politically, have many stakeholders who must be satisfied and generally span many years and political election cycles. To be successful they must meet expectations, function efficiently, and be delivered under, at or close to budget and schedule. There is a widely-based perception that large, complex projects are always delivered late, over budget and with problems. Specific examples include projects such as Tren Urbano in Puerto Rico – $1.28 billion over initial budget (+133%), the Silver Line Transitway Project in Boston – $286 million over budget (+90%), the London Jubilee Line Transit Project – 2 years late and £1.4 billion (+67%) over budget, the Channel Tunnel Rail Project – £3.7 billion (+80%) over budget, Denmark’s Great Belt Link rail and road link (54% over budget), the 2003 Woodrow Wilson bridge tender in Virginia (72% over estimate) and Boston’s Central Artery Project – several billion (perhaps 100%) over what would have been a realistic initial budget and years late (Reilly 2001c, 2004a; Salvucci 2003)."

Jan 1, 2016

In 1991, most industrialized countries, except for Germany, were in a recession or a period of reduced growth. The US economy, already in recession, suffered from mounting banking system losses and the uncertainty brought about by the Persian Gulf War. However, US and worldwide minerals exploration did not collapse as it did during the mid-1980s. Even though gold and base metal prices declined, prices were still above cash costs for most operations. This allowed the continuation of established exploration programs but sharply limited new initiatives. Exploration 1990-1991 Planned worldwide 1991 exploration expenditures declined by about 8% from 1990 levels, according to a survey of 153 companies by the Metals Economic Group (MEG). Canada was the leading exploration target with 23% of the total, followed by Australia and the US (19% each), South Africa (13%), Latin America (11%) and the South Pacific (7%). The remaining 8% was split evenly between Europe and the rest of Africa. In Latin America, Mexico and Chile are the most attractive countries for exploration. Recognizing the risks involved, the industry has been cautious about ventures in the former Soviet Union. Survey results also showed that while the majors expected to maintain exploration spending, smaller firms were cutting back or actively seeking farm-outs from the majors (personal communication, M. Wegener, MEG).

Jan 1, 1992

By J. Wagner, P. Eger, G. Melchert

In 1991, LTV Steel Mining decided to close an open-pit taconite mine in northeastern Minnesota using a passive-treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. More than 50 Aft (55 million st) of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages. Before the closure, the annual median concentrations ranged from 1.5 to 50 mg/L. Copper, cobalt and zinc are also present but they are generally less than 5% of the nickel values. Median pH levels range from 5 to 7.5, but most of the stockpile drainages have pH levels greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential that a stockpile had to produce acid drainage, the lower the permeability of the capping material required Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to more than 90% for the plastic liner. Five constructed wetlands have been installed since 1992. They have removed 60% to 90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1 % of those for an active treatment plant. Because mine-drainage problems can continue for more than 100 years, the lower annual operating costs should pay for the construction of the wetland-treatment systems within seven years.

Jan 1, 2000

By Marc Lemieux

A new moving cone optimizing technique will be introduced. In order to facilitate under- standing of the moving cone optimizer, a re- view of the principles of moving cone design technique is presented. A concept called the negative moving cone design technique is also introduced to help facilitate understanding of the moving cone optimizing algorithm. In the introduction to Subsection 3.3, the relationship of the mineral inventory modeling technique to the ultimate pit design optimization methods was reviewed. Five modeling techniques were described, and four mathematically provable optimizing methods discussed. The broad use of the regular 3D fixed block model was attributed, in part, to its applicability to automatic optimization methods of pit limit design such as the Lerchs-Grossman graph theory algorithm, and in part, to its systematic nature.

Jan 1, 1979

By G. M. Wilemon, B. J. Scheiner

The Bureau of Mines conducted investigations on extracting phosphate values from fine-particle wastes generated during the mining and beneficiation of phosphate ore by leaching dried wastes using a H2SO4-methanol mixture. Although phosphatic clay waste contains up to a third of the phosphate originally present in the ore, recovery of these values represents a significant challenge due to the fine grain size of the material, the particles averaging less than one micrometer in diameter. Waste samples obtained from two Florida producers yielded phosphate extractions of 71 and 84 pct, respectively, when leached under ambient conditions and at a stoichiometric acid ratio of 1.4:l. Elevated temperatures did not improve the amount of phosphate extracted. Undesirable A12O3, Fe2O3, and PlgO impurities were largely rejected; higher grade wastes gave acids that meet established industry impurity standards and lower grade samples yielded acids that marginally fell short of the standard. Separation of the crude acids from the insoluble residues was accomplished via vacuum filtration through either filter paper or commercial filter cloths. Both filtration rates and solids retention were improved by the addition of 0.5 lb/ton of poly(viny1 acetate) (PVAc) or poly(ethy1ene oxide) (PEO) to the methanol-acid slurries. These results show potential for substantially increasing the reserves of an important domestic resource.

Jan 1, 1989

By J. W. Wilson, S. Nakajima, B. D. Singh

According to the Project Independence blueprint, a 270 percent increase in coal production is expected from western coal fields compared to an increase of 100 percent for the nation as a whole. Furthermore, 30 percent of the total United States coal reserves lie in the western states, which are classified as beyond the strippable limits and can be recovered only by underground methods. In view of the fact that the majority of the seams in the West are thicker than those presently mined in other parts of the country, it is important to consider the parameters that relate to mining thick seams and the factors that affect such mining systems. Apart from thick seams, a common feature of many western coal fields is the occurrence of multiple seams that lie in close proximity to one another. These multiple seam deposits present difficult mining problems that have not been encountered to any degree in other U.S. coal fields; for example, ground pressure changes in one mine level caused by mining in the other, sudden water or gas influx from the adjacent levels, the danger of spontaneous combustion in gobs and large and complex subsidence displacements on the surface. Perhaps equally important is the fact that the country can ill afford the present systems of underground mining that attain only 50 to 60 percent coal recovery. With the probability of increased thick seam mining, conservation shall be a focal point in future mine design systems. It is possible that in the future it will be forbidden to adopt the present day wasteful mining methods to ensure that coal can be conserved for future generations.

Jan 1, 1977

By P. J. D. Lloyd

INTRODUCTION The mining of gold commenced on the Witwatersrand in 1884, and reached a mature state by about 1910, when nearly 20 million metric tons were mined. Mining has continued on the central Witwatersrand, the area of the first mining, at a similar rate until recent years. As a result, well over 1 billion tons of gold mining wastes have been dumped along a line over 80 km long, centred on Johannesburg and stretching from Randfontein in the west to Nigel in the east. (see Figure 1). The population of this conurbation, which straddles the line of mining, has grown to about 5 million. In 1922 uranium was first discovered as a constituent of the ore (and thus of the wastes). Investigations in the 1940's revealed that values near Johannesburg were low, but that, at the western and eastern ends of the central Witwatersrand line, and in the new areas centred on the towns of Carletonville, Klerksdorp and Welkom up to 200 km from Johannesburg, values were adequate to permit uranium recovery. Commercial production commenced in 1952, and by 1979 over 100 000 tons of uranium oxide had been produced. There thus arises on the central Witwatersrand nearly 1,3 billion tons of slimes containing an average of about 0,005% uranium and about 1,8% FeS2. The material grading is about 70%-75µm, and the primary mineral is silica (over 85%). The material is contained in dams constructed hydraulically. A typical dam has an area of about 100 hectares and there are over 6000 ha under slimes dams in the area of concern. The treatment of these dams for uranium recovery commenced in 1977. The situation has thus arisen whereby potential uranium ores have unwittingly been dumped in significant quantities within a major metropolis over a period of nearly a century. The purpose of this note is to review the experience arising from the potential hazard over a considerable time.

Jan 1, 1980