Search Documents

Researchers at National Institute for Occupational Safety and Health (NIOSH) are investigating how fiber-reinforced shotcrete mix designs can be extrapolated from proven designs employing wire mesh. This paper explains the results of round determinate panel tests and relates the flexural strength and toughness of fiber-reinforced shotcrete to known energy absorbing properties of wire mesh. The energy absorbed with central deflection is strongly influenced by the amount of fibres. The higher the energy absorption the more load cracked shotcrete can support. Two types of fiber-reinforced shotcrete were investigated, one with steel fiber and another with polyfiber. The residual load supported in Round Determinate Panel Tests can be matched with the strength of wire mesh, thus providing equivalent bag strength values for fiber reinforced shotcrete panels. There is also evidence of a panel crack width comparison to the load holding capabilities of the fiber in the shotcrete mixes. In practice, this provides designers with a method for comparing the ground support provided by fiber-reinforced shotcrete with that supplied by wire mesh.

Jan 1, 2010

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

How representative are partial-panel screen tests of the in situ response of screen to roof and rib deterioration and displacements? Can a more representative procedure that tests up to two full screen panels improve the utilization and effectiveness of screen as a roof and rib support? This paper details a new full-panel screen test procedure and the initial results. The full-panel test frame was designed to test a 2.4 by 3.6-meter screened area with bolt spacing as small as 0.3-meter increments. The initial design included up to 6 screen pull points, but additional locations can be added to produce a more uniform loading. The test frame was developed to capitalize on the capabilities of the Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division (PMRD) of the National Institute for Occupational Safety and Health (NIOSH). The initial tests included a baseline test of a partial panel (1.22 by 1.22-m screen section) using the original 1.52 by 1.52-meter test frame, a 1.22 by 1.22-meter screen section test in the new full-panel test frame, and two tests of 2.4 by 3.6-meter screened area in the full-panel test frame. The 1.22 by 1.22-meter screen section tests in the full-panel test frame produced a peak load 6% higher and a yield load 30% lower than the partial-panel (original) test frame. The multiple pull points of the full-panel frame produced variable yield, peak, and intermediate loads, but on average were lower than the single pull-point tests. INTRODUCTION Roof and rib surface support has become a major component of the stability and safety of underground coal openings in the past 15 years. The use of screen, either metal or synthetic, has proven to decrease the injuries of underground coal miners. By 2005, there were 466 injuries in the United States caused by roof skin failures, with numerous mines not employing roof screen. In contrast, in 2015 there were 175 injuries caused by roof skin failures, with at least some of the reduction due to the increased use of roof screen. A continued effort to increase the utilization of screen in areas of underground coal mines where workers are traveling and working can reduce these injuries even further. To aid in this effort, the testing of various screen types under various loading and attachment conditions is required. Past testing efforts have primarily consisted of partial-panel testing in a laboratory setting. Laboratory testing of roof screen, both metal and composite, has been conducted in several ways by researchers, manufacturers, and other entities. The primary focus on the testing has been evaluating weld integrity of 1.22 by 1.22-meter screen section tests of various screen types utilized in mining (Dolinar, 2006; Dolinar, 2009; Tannant, 2001). There have also been several efforts at numerical simulation of the screen and screen/rock interactions (Murali et al., 2006; Shan et al., 2014). A few full-panel tests were performed with one pull or loading point in the center of the screen panel (Shan et al., 2014). As most previous efforts have mentioned, the only true way to evaluate the capabilities of screen is to conduct full-panel testing. Single wire strand, weld, and partial-panel (1.22 x 1.22-m) tests as well as numerical modeling only provide insight into the actual response of full-panel screen. A new test frame and procedure have been developed at PMRD to conduct various loading, anchoring, and material testing.

Jan 1, 2019

This paper summarizes the process development behind the design of three different types of paste fill plants at operating Canadian hard rock mines. Each application has a unique paste backfill mix and process which utilizes the materials economically available to the mine site. The different plants produce paste fill composed of base metal tailings, a blend of recovered disposal pond tailings fines and alluvial sand, gold ore tailings, and a blend of gold ore tailings and alluvial sand. This work has led to the joint development by Inco and GL&V Ontario of the compaction storage mechanism for the de-watering of mill tailings to a paste consistency.

Jan 1, 1994

By Benjamin C. B. Hsieh

Many processes in the hydrometallurgical and chemical industries require the separation of dissolved material from suspended solids. Counter current decantation (CCD) with thickeners is one of the methods generally used. The process engineer needs a quick and accurate CCD calculation method. Several theoretical 1-12 CCD calculation methods are available in the literature . The simultaneous 1, 2 equation method for a complex circuit as used would take too long to solve the problems. Approximate equation method1 is not accurate and is for simple cases only. A shortcut method developed by Counselman3 contains no mathematical equation, and thus is not suitable for computer programming. Based on Counselman's method, Woody4 derived two simple equations in terms of percent soluble loss for two typical examples. Scandrett5 included a term for mixing in his formulas. This mixing efficiency was defined by Murphree6. Another method which depends on making volume calculations instead of using weights is presented by Mastin8 and Cahalan9. None of these methods is related to dissolution and pre¬cipitation reactions. Chen 10,11 demonstrated his methods for counter current leaching. His results are calculated from the general solution of a derived linear difference equation for constant underflow, and from the solution of a derived non-linear Ricatti difference equation for variable underflow. This paper concerns derivation of a general equation for CCD washing with provisions for adding and withdrawing the streams, and for leaching (dissolution) or precipitation reactions. These equations take several forms depending on the input information available. A set of simplified equations for continuous counter current washing and leaching is derived for determining:

Jan 1, 1972

By Taghi Sherizadeh, Paul Brooks, Dogukan Guner, Samuel Nowak

Large excavations are well known to result in rock mass deformations which can present challenging situations for mine personnel. Most of the currently available ground movement monitoring devices fail to adequately provide mine operators with highly accurate and meaningful insights into rock mass deformation or displacement. The use of distributed fiber optic sensors (DFOS) in industries such as oil and gas and civil engineering has shown the potential of these sensors to deliver real-time, highly accurate, and long-range distributed strain measurements with great success. However, the use of these sensors in underground mining is limited to a few case studies.

By D. Crouse

A significant wollastonite resource has been discovered and evaluated near Seeley's Bay in southeastern Ontario. The deposit occurs in Grenville Frontenac Terrane granulite facies rock within a calc-silicate skarn in contact with Proterozoic-age gabbro. The steeply-dipping and tightly-folded wollastonite skarn beds are interlayered with diopside and quartz-feldspar skarns in a southwest-plunging synclinorium. More than 9 million tonnes of a drill-proven and inferred resource grading 41 % wollastonite has been identified, as well as an additional 3 million tonnes grading 30%. Mineralogical and process test work with the wollastonite from this deposit has demonstrated the potential to produce a high purity, high aspect ratio wollastonite product.

Jan 1, 1994

By Eugene L. Foster

The engineering profession has traditionally devoted its efforts to understanding and modifying the Earth's environment in order to adapt it to man's needs. In appraising our overall performance, I would have to say it has been a mixed bag. In many areas, notably communications taken in the broadest sense, and development of creature comforts, we have done a good job. In others, we have failed, particularly in our assessment of the effect of our work on the environment. Our failures have been due in part to a lack of understanding or foresight, and in part to a disproportionate emphasis on lowest first cost. Now, with an increasingly large number of people living in a finite environment, there is an urgent need for reassessment. It is no longer possible to pursue a single objective without regard to its side effects. Our projects are too large, and there are too many of them. Environmental impacts must be taken into account in all important engineering decisions of the future. There are forces at work which will help to bring this about. Thinking people everywhere have realized that adverse alteration of our environment eventually affects every one of us. The majority of our citizens, who now live in cities, are beginning to appreciate the advantages of a good natural environment in a way which others who have been closer to the soil have appreciated for years. Our people have flocked to the cities because they wanted to be "where the action is." At the same time, there is a strong desire for what we have come to call the quality of life. Today, we all want the standard creature comforts. We want to be able to move freely

Jan 1, 1974

By K. Fuenkajorn

Geomechanics and geohydrological considerations for the seal design for mine openings are presented. Design guidelines derived from laboratory and in-situ experiments are proposed. The results suggest that seal design, specifications and material selection should be site-specific. Performance requirements for a specific seal location should be identified. Evaluation of sealing effectiveness should be made on the entire seal system, i.e. seal, seal-rock interface, excavation-induced damage zone and the surrounding rock.

Jan 1, 1997

Paper and paperboard manufacturers need to quantify the carbon footprint and environmental impact of their products to satisfy market, social and government demands. Coated paper products contain minerals, such as kaolin and calcium carbonate, at significant levels; some coated paper grades have mineral contents as high as 45% by weight. Some uncoated paper has no mineral content, but most uncoated paper contains some mineral to improve appearance, process efficiency and cost. Super-calendared paper grades can contain levels of mineral up to 35% by weight. This paper describes how to calculate the carbon footprint of kaolin and calcium carbonate minerals used for white pigments. The carbon footprint of these minerals strongly correlates to the primary energy sources, final product form and energy used to calcine kaolin and lime. Kaolin and calcium carbonate pigments have a favorable impact on the carbon footprint of paper and paperboard products by directly substituting for fiber and by reducing the energy needed for paper making. Key words: Kaolin, Calcium carbonate, Paper production, Carbon footprint, Lifecycle analysis

Jan 1, 2010

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

Electronic detonators have been in commercial use for a decade, with an excellent safety record. This paper lists known incidents involving electronic detonators. Typical standards required by regulatory bodies for static electricity and electromagnetic fields are reviewed. The performance of some detonators is compared to these standards; in general the minimum standards are easily exceeded. The general resistance of electronic detonators to extraneous electrical energy that can be derived from the body of test results is compared to danger levels for exposure of humans to these energies; it is shown that electronic detonators can safely tolerate higher electrical energies than people can. This comparison includes comparable data for electric detonators, which are shown to be more vulnerable to extraneous electrical energy than people are. Electronic detonators also bring significant safety benefits in blasting due to their testability, two-way communications, reliability, programmability and precision. The links between these attributes and enhanced safety are discussed with examples from actual blasting. Although electronic detonators are usually more vulnerable to extraneous electricity than non-electric initiation systems, the paper shows that the net safety benefit in handling and blasting is in favor of electronic detonators, which are the safest initiation system that has ever been offered to the mining industry.

Jan 1, 2010

By Z. Henderson, J. Saylor, L. R. Mendoza

"Diesel particulate Matter (DPM) is a byproduct of fuel combustion in diesel engines. It is classified as a carcinogen, with associated respiratory and cardiovascular health effects. The composition, size, and concentration of DPM is dependent on factors such as engine type, loading and fuel composition. Though a number of DPM abatement and control strategies currently exist, particularly in underground mining environments, occupational exposures remain a serious health concern. As a novel abatement approach, DPM scavenging by fine water or “fog” droplets has been proposed and a laboratory set-up has been built to test the efficacy on engine exhaust. Here, we describe a series of tests that varied engine load, system flow rate and fog drop number density. While none of these factors had overwhelming effects on the results within the ranges tested, the improvement in DPM mass removal attributed to the fog treatment was about 45% on average in comparison to no treatment. INTRODUCTION Diesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy1. More recently, however, adverse health risks of diesel exhaust have become increasingly clear. Many of these risks are associated with the physical and chemical properties of exhaust components1–3. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are a mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash3. The OC fraction of DPM results from unburned fuel and lube oil, whereas EC or soot is formed during the combustion of locally rich regions within the fuel. DPM is classified as a carcinogen6,7 and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustion-related fine particulate and increased cardiovascular and pulmonary diseases8,9. Diesel engines operate in relative fuel rich/oxygen lean conditions and are characterized by relatively high emissions of particulate as compared to spark-ignition engines2,3,10. Typically, these emissions range from 107 – 109 particles/cc and cover two primary size ranges: the nuclei mode where particles have diameters less than about <50 nm, and the accumulation mode where diameters are from about 50-10,000 nm. Most OC resides in the nuclei mode as semi-volatile compounds, while most EC is in the accumulation mode3. The physical and chemical properties of DPM vary with the type of engine, fuel (e.g., petro- vs. bio-diesel) and operating conditions such as loading (i.e., a function of torque and rotational speed)2,3,9,11,12. Loading is a particularly important factor with respect to DPM toxicity9,13,14, and on the effectiveness of after-treatment technologies2,3,15. Engine load alone can affect the EC/OC ratio, and the size distribution and number density of DPM. For diesel engines, the load is roughly proportional to the equivalence ratio3, defined as the actual fuel/air ratio over the stoichiometric fuel/air ratio for complete combustion. Light loads generally favor the formation of OC and small particles. As load is increased the volatiles are oxidized leading to larger soot particles (i.e., EC), but lower total number density of DPM. With further loading, the formation of soot offsets the decrease in volatiles, resulting in increased DPM mean size and number density3."

Jan 1, 2017

By L. R. Moore

The World Health Organization (WHO) considers contamination from oxyanions, such as selenium and arsenic, a global concern. While their elemental forms are toxic, the aqueous oxyanions are more so. These aqueous forms, which exist at a higher oxidation state, are the most common forms released during mining processes. Many technologies are capable of meeting the governmental discharge criteria for oxyanionic contaminants, but may possess limitations due to redox chemistry as well as the water matrices. An innovative technology was developed that can successfully reduce such aqueous forms generated during mining processes to a level below the discharge criteria. This paper discusses how an understanding of the sensitivities of this novel adsorbent towards these variations in water matrices and redox chemistry can be used to optimize its application.

Feb 27, 2013

By E. Watkins, V. Gangrade, P. Zhang, J. Addis, D. W. H. Su, T. Minoski, C. Hollerich, M. Van Dyke, S. Schatzel, H. Dougherty

"This paper presents the results of a comprehensive study conducted by the Centers for Disease Control (CDC), National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD) to evaluate the effects of longwall-induced subsurface deformations and permeability changes on shale gas well integrity and safety under shallow cover. NIOSH researchers selected a study site over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under 482 feet of cover. One in-place inclinometer well and three permeability monitoring wells were drilled and installed over a 125-ft by 275-ft centers abutment pillar. In addition to the inclinometer well and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the first 1,500-ft-wide longwall panel on the south side of the abutment pillar mined by the site.A number of FLAC3D finite difference simulations (Itasca Consulting, 2017) were conducted to estimate surface subsidence, coal pillar pressure increases, and horizontal displacements in the in-place inclinometer (IPI) monitoring well. Comparisons of the FLAC3D finite difference simulation results and the surface, subsurface, and underground instrumentation results show that the measured IPI casing deformations are in reasonable agreement with those predicted by the FLAC3D models, and that the measured surface subsidence and underground pillar pressure are in excellent agreement with those predicted by the 3D models. Measured permeability changes were incorporated into a preliminary calculation to evaluate the effect of a hypothetical shale gas well leak on longwall ventilation. Results from this 2018 research clearly indicate that under shallow cover, the measured horizontal displacements within the abutment pillar are at least one order of magnitude higher than those measured in a 2017 study under deep cover and slightly higher than those measured in a 2014 study under medium cover. This research represents a very important step and initiative in utilizing the knowledge and science obtained from mining research to improve miner and public safety as well as the safety and health of the workers in the oil and gas industries"

Jan 1, 2019

By P. Sander, M. Spiegl, J. Reilly, A. Van Droogenbroeck

Although the outdated idea of calculating risk as the deterministic product of its likelihood and impact is not entirely a thing of the past, a multitude of organizations have adopted the usage of probabilistic methods for risk analysis, as they better reflect the inherent uncertainty of cost and risk estimates with ranges. But are these advancements sufficient in a complex environment such as tunnelling projects, where inadequate modelling of cost and risk can result in estimate discrepancies that run into millions of dollars? This paper explores two advanced probabilistic modelling techniques for tunnelling projects. The first one demonstrates how the cost and schedule uncertainty related to changes in excavation and support classes can be modelled with correlated variables. The second example models the risk related to explosive ordnance clearance on construction sites using a probabilistic event tree.

Dec 1, 2022

By Enrique Jelvez, Nelson Morales Varela, Christian Ihle, Joaquin Silva

All mineral beneficiation processes require water for its execution. Therefore, the availability and adequate management of water are key to the existence of any mine operation. However, many mines’ operations are affected by water scarcity and risk an increase of operational costs or even production in some cases. This paper proposes a model to minimize the losses of water due to evaporation and re-absorption by adjusting the active and inactive periods of the discharge in different points of the tailing. When applied, the model determines optimal or nearly optimal discharge operation in all the scenarios that were evaluated.

Jun 25, 2023

By Felix Schmid

ABSTRACT Lateritic bauxite deposits of economic size and grade in Sierra Leone occur on granulites of the Kasila series. The high grade trihydrate ores of Mokanji are exploited by SIEROMCO since 1964. Remaining reserves are small (2 million tons) and operation moved over to the Gondama deposits of similar grade. Port Loko bauxite reserves are estimated at 100 million tons and are of relatively lower grade. It is planned to treat this ore locally into alumina. Guinea&apos;s bauxite reserves exceed those of any other nation. They occur as hard lateritic bauxite covers on plateaus of the Pre-Cambrian sedimentary formations and on doleritic intrusions. The genesis is still controversial. The Sangaredi mine has produced high grade ore for the last 10 years. Friguia exploits a relatively lower grade ore at a rate of about 2 million tpy to be treated in their local alumina plant. Kindia ore is mined at a yearly rate of 2,5 million tons since 1974. Untouched reserves at Ayékoyé and Tougué/Dabola are estimated at 6,000 million tons.

Jan 1, 1984

By J. K. Ross, K. O. Hoal, S. K. Appleby

Understanding ore variability is a key factor in the geometallurgical analysis of a deposit and is beneficial to process development and mine planning. Ore variability is a function of the mineralogy of a deposit, in terms of both ore and gangue minerals and their textural relationships. This study integrates optical microscopy and quantitative mineral analysis to characterize the mineralogy and texture from 13 samples from different lithologic units at the Bingham Canyon Mine. The analysis identified several parameters, such as modal mineralogy, alteration assemblages, distribution of mineral phases and alteration assemblages and microfracture and void space distribution. These parameters can have an impact on the materials’ behavior during processing. This study demonstrates that quantitative mineralogical analysis can provide detailed information for improved understanding of ore variability.

Jan 1, 2010

By L. Kulik

Sustainability of lignite mining in the Rhenish lignite mining area is ensured by a preceding study of the overall project, with the involvement of all those affected. The supporting holistic consideration of the various sustainability elements is essential for a later balancing of the several ecological, economic and social concerns. In what follows, a brief overview of the Rhenish lignite mining area is given as introduction to the focus of this report, which is on sustainability, starting with the approval procedure under regional planning law incl. opencast mine planning, and extending to concrete on-the-spot implementation, taking the Garzweiler II follow-up mine as example. To illustrate the issues involved, an account is given of some selected sustainability elements.

Jan 1, 2005

By T. P. Meloy

Riffles on a shaking table have a major effect on particle separation. This effect is modeled in a spreadsheet.

Jan 1, 1993