Search Documents

By Donald P. Richards

West Elk Coal Company operates its Mt. Gunnison No. I mine on the western slope of the Rocky Mountains in Western Colorado. The mine is located along the north fork of the Gunnisson River near Somerset, Colorado as shown in Figure 1. The mine is designed for a sustained production of 1.4 million tons per year out of the "F" coal seam in the Mesa Verde formation. The coal seam is nominally 7 feet in thickness and dips at about 3 ½ degrees to the northeast. Mining of the seam is up dip with the entry portals on the north facing slope of Mount Gunnison. The mine is designed as a five entry system with four entries for ventilation and access and one entry for a coal-handling conveyor. The mine entry layout is shown in Figure 2. Initial mine planning began in 1979, with "permitting" complete and construction starting in the fall of 1981. A "turnkey" contract for design and construction of all five parallel mine entry tunnels was awarded by West Elk Coal Company to a Joint Venture of Jenny Engineering Corporation (design and contract management responsibility) and Affholder, Inc. (construction responsibility). The first entry access into the coal seam was completed in the early spring of 1982. The mine has been operating at full service (all five entries) for nearly 3 years.

Jan 1, 1984

By Leo L. Van Sambeek

Specification of properly sized pillars to support the overburden is one of the most challenging aspects of salt mine design. Interest in salt pillar design is heightened by the recent flooding of the Retsof salt mine, water inflows to the K2 potash mine, and closing of the Belle Isle salt mine because of ground control problems. A series of numerical modeling analyses show that a simple pillar design equation for salt pillars adequately reproduces results of extensive modeling efforts. The paper describes (1) the basis for the pillar design equation, (2) equation verification by comparison with numerical modeling results, and (3) equation validation by comparison with measurements and observations of salt pillar behavior.

Jan 1, 1997

By M. O. Serbousek

In 1975 the Bureau of Mines Spokane Research Center began a series of laboratory and field tests to investigate the feasibility of developing a substitute for the organic chemicals used in resin roof-bolting systems. An inorganic system, comprised of calcinated gypsum, an accelerator, and microcapsules of water was developed and patented by the Bureau in 1977. The system has several advantages including economics, non- toxicity, nonallergenic, inflammability, and is not based on petroleum products. Two roof-bolting systems utilizing inorganic cements are under development at the Spokane Research Center--a cartridge system, using the microcapsules of water and accelerator, and a slurry system, using a mix-inject method which combines dry powder cement with water for simultaneous injection into a predrilled roof-bolt hole. Several underground field tests have been conducted in eastern coal mines. Test results indicate that inorganic cartridge systems are adequately supporting mine roof in several test sections. Economic potential for the bolt systems appears favorable.

Jan 1, 1981

By Vincent Scovazzo

Cost-effective underground mine configurations have been designed in highly fractured rock masses where the stone possesses a high material strength. A limestone mine in the eastern United States is used to demonstrate procedures for the geotechnical design of one such operation. The mine discussed is located in both limbs and the axis of a recumbent fold that fractured the rock mass. In a highly fractured rock mass, where the host rock has high strength, a design can be developed to alleviate intact rock failure. This is possible because in most cases as the stress levels needed for intact failures are approached, the stresses are quickly dissipated due to movement along discontinuities, which represent planes of weakness. As a result most underground failures in highly fractured rock are due to sliding or toppling. Even when intact rock fails in a highly fractured rock mass, it is the movement along an existing joint or other weakness plane that often initiates or causes this failure. It is therefore important to obtain the characteristics of weakness planes that are the discontinuities within the mass. The required information on weakness planes, geology, and strength of materials is discussed and recommendations for obtaining this information are presented. A discussion is provided on failure modes and the use of developed information for their evaluation. The impact on geotechnical design is demonstrated through pillar sizing procedures; however, this approach can also be applied to mine roof and pillar foundations.

Jan 1, 2002

By Chris Adams

The application of pre-tensioned tendon roof support assisted Harworth Colliery in their revival, from impending closure to lowest cost deep-mined producer in the UK, over just six months last year. The paper describes this success story, how it came about, the reasons "why", and the method "how"

Jan 1, 2003

By Kanaan Hanna

The integrity factor approach was developed by the Bureau of nines to assess the stability of mine pillars and has been applied primarily to longwall chain pillars. Recently this approach was applied to a room-and-pillar mine in the Illinois Coal Basin. A special configuration of hydraulic borehole pressure cells was installed in a pillar to determine the in situ strength-and- stress relationship of the coal pillar and to verify the applicability of the integrity factor approach. Results indicate that the integrity factor approach is applicable to the assessment of pillar st6b:lity and nay bs a realistic and effective approach for room-and-pillar mine design.

Jan 1, 1988

A procedure fm the estimation of pilla1 strength is presented where the design of underground coal pillars is emphasized. An analytical approach has been developed, proposing that the effect of end constraints on the pillar strength and the ductile behavior of coal material should be incorporated in the computation of the stability of coal pillars. Bad on this approach, it has been found that end constraint has a significant influence on the pillar strength. The study indicates that when the end constraint is zero the computed strength of the pillar is the same as the unconfiied compressive strength of the coal mass and will not increase with the increase in the width to height ratio. However. when the end constraint is greater than zero the pillar strength will increase exponentially as the width to height ratio increases.

Jan 1, 1990

The formation of tension cracks in slopes is well known. Analytical studies require the determination of a critical slip surface for any slope and, in doing so, it is necessary to consider an appropriate tension crack. A general yet simple approach is proposed for identifying the critical slope failure surfaces associated with critical tension cracks. The minimum factor of safety consequently reflects both safety against shear sliding and tensile failure. In general, the critical slope failure surface for a slope determined in this way differs from that which is obtained without optimizing the position and depth of the tension crack. In particular situations, the difference is significant.

Jan 1, 1989

By D. F. Howarth

Two innovative ground reinforcement products have been developed for use in the mining industry. One of these products is a high strength polyethylene (HOPE) bar for use as a rib bolt in underground coal mining and as a corrosion proof tendon in open pit mines. The other product is a cable bolt (Ultrastrand) which demonstrates enhanced load transfer and is available in continuous lengths. Ultrastrand's exceptional in¬situ performance and versatility makes it ideal for mechanised installation in both underground and surface mining operations. Details of these products are presented and results from labortaory and field trials are discussed.

Jan 1, 1992

By John Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a mine slope entry, the problem becomes more complicated because a slope transverses through many different types of strata. Mine slope ground control has traditionally been practiced based on trial and error and prior experience. There is currently no well-accepted slope and support design methodology available for an economical and technically sound ground control plan. Over the last few years, Keystone Mining Services, LLC (KMS), the engineering affiliate company of Jennmar Cooperation, has developed a ground support design methodology called the ?Stress, Geologic, and Support design system? (SGSSM). This patent pending method enables accurate analysis of actual geo-technical conditions and stress; identifies strong, fair, and weak sections along the slope; formulates primary and supplemental roof bolting systems, designs optimal long-term steel structure support; and verifies the adequacy of the developed support. The method has been successfully utilized on various new slope projects and has been well received by state and federal regulatory agencies during the approval process. This paper details the concepts of the methodology using an actual case study of a slope project in the Midwest.

Jan 1, 2011

By S. M. Matthews

The magnitude and orientation of the in situ stressfield has been determined as a key factor in controlling the stability of openings for both coal mine development and extraction. Monitoring of roadway and pillar behaviour in conjunction with numerical analysis has identified specific stress control measures that have been successfully applied to improve productivity in underground coal mining operations. The influence of the major horizontal stressfield on the stability of openings has been identified at a wide range of sites including mines in Australia, Britain, the USA, New Zealand and Japan. Stress mapping, stress measurement and stress monitoring techniques have been applied to define the in situ stress regime and, together with the correlation of measurements of rock deformation and rock reinforcement behaviour, has enabled appropriate stress control measures to be developed. Stress control measures for development headings have required the selection of roadway orientation, roadway sequencing, reinforcement density and pillar size. The monitoring of behaviour at a range of trial sites has confirmed significant improvements in development stability. Stress control measures for longwall extraction have required rational selection of longwall orientation and extraction direction. Where a mine layout design incorporating the optimum longwall layout design has not been possible, the use of sacrificial roadways has been successfully applied to protect key roadways from stress concentration effects. Comprehensive in situ monitoring of behaviour has been carried out to confirm the mechanisms involved.

Jan 1, 1992

By Leo Gilbride

Western U.S. longwall operators face increasing challenges with optimizing ground control and productivity as mines reach greater depths and coal bursting hazards increase. Some western U.S. mines, many known to be bump-prone, achieved a successful balance between ground control and productivity by transitioning to side-by-side longwall panel mining combined with a yield pillar gateroad system. With this design, development footages could be minimized and pillar bumping averted by controlled yielding at moderate depths, generally in the range of 450 to 600 m. Over the past four decades, the yield pillar system has won wide acceptance among western mines facing pillar bursting hazards, particularly those in the Wasatch Plateau and Book Cliff coal fields of central Utah. However, recent attempts among the deepest Utah operators to mine side¬by-side panels with yield pillars at depths in excess of 600 m have been met with mixed success and, in some circumstances, with serious difficulty. Challenges include violent face bursting and excessive tailgate convergence outby the face, which can be crippling to ventilation. The use of interpanel barriers, i.e., barriers left between longwall panels, offers one possible solution to mining under deep cover with bump-prone geology. Interpanel barriers have already been adopted by Utah's deepest longwall mine, and others are considering their use. The geomechanical implications of mining with and without interpanel barriers, and the competing tradeoffs between ground control and ventilation are discussed.

Jan 1, 2004

By Peter Zhang

As simpler and easier reserves are exploited to depletion, underground coal mining continues in more complex geologic settings and conditions. Roof bolting for long-term entry stability is always a challenge. For long-term entries of a mine such as belt, track entries and return airways, roof could be under-supported if one uses the same bolting plan as in short-term entries or even seem over-supported with increasing use of longer, stronger bolts along with mesh, pans, straps or trusses. In most underground coal mines, roof deteriorates over time with cutters developing deeper in entry corners; roof sagging and popping out between bolts; entry width increasing due to rib sloughage; and separations developing deeper up into the roof. In deteriorated long-term entries, roof falls could occur at certain locations and re-bolting could be costly or sometimes unfeasible. Therefore, it is important to choose an appropriate bolting plan during development based on mining and geologic conditions if the entries will be used for the long-term. In both short-term and long-term entries, primary roof bolting is critical in building a strong and effective beam. But in long-term entries, supplementary bolting is necessary in certain cases to ensure roof stability can still be maintained even if a roof failure develops beyond the primary bolted horizon. This paper deals with roof bolting for long-term entries based on studying the progressive roof failure and roof falls under different geologic conditions. The paper presents bolting considerations in terms of bolt type, length, diameter and spacing as well as bolting strategy to minimize the risk of roof falls in long-term entries.

Jan 1, 2011

By David A. Newman

Strength and physical property testing of coal is conducted regularly by the Arch Mineral Corporation as part of reserve exploration. Pillar design and mine layout are the primary applications for the coal strength data. Distinct differences in pillar behavior were observed during longwall mining at a mine in Southeastern Kentucky. Horizontal and vertical variation in both triaxial and uniaxial compressive strength was observed within the four (4) benches of the Harlan seam. Similarly, geographical variations in coal strength were noted across the Harlan seam reserve. During the past three decades substantial research efforts have been focused upon coal pillar behavior and the refinement of pillar design methodologies. Ironically, little attention was directed to integrating the variability of coal strength into pillar design. The authors examine, through the presentation of case history data, i) typical industrial practice with respect to establishing a database of coal strength for use in pillar design and stability analysis, ii) approaches in which the observed variation in strength in the Harlan seam is integrated into pillar design and stability analyses, and to iii) propose standards for coal cube testing

Jan 1, 1993

By Gift Makusha

Surface subsidence associated with coal mining activities in the Mpumalanga Province of South Africa changes the natural environment in several ways, and current challenges for mining companies include rehabilitation of the natural environment and the prevention of further degradation. To monitor the spatial and temporal evolution of surface subsidence, traditional fieldbased monitoring approaches such as GPS and spirit leveling are employed at a number of locations. However, the resulting measurements are point-based, and frequent revisitations are necessary to map the evolution of surface subsidence basins over time. To address these limitations, differential interferograms derived from repeat-pass satellite-borne synthetic aperture radar (SAR) systems were tested for their ability to measure and monitor surface deformation. The SAR data was captured by the European ERS-1 and ERS-2 satellite and covered a timeframe between 2008- 09-15 and 2008-09-15. The resulting interferograms revealed several features indicative of surface subsidence. Ground truth data confirmed the presence of a subsidence basin, detected using differential interferometry techniques during the 35-day period between April 12, 2008 and May 17, 2008; a maximum vertical deformation of 3.2 cm (1.3 in) was recorded. Interferometric monitoring revealed an eastward migration of the subsidence basin between June 2, 2008 and September 15, 2008 with an additional 4.7 cm (1.9 in) of subsidence observed. This migration coincides with the advance of the working face of the mine during this period. Finite element modeling will be performed in order to model the rates and evolution of surface subsidence haloes as underground mining advances. These presented results demonstrate the ability of interferometric synthetic aperture radar techniques to measure surface subsidence as well as the monitoring of the evolution of subsidence basins over time. This implies that the technique could be included, together with traditional field-based surveying techniques, in an operational monitoring system. With knowledge on deformation rates and subsidence basin evolution, informed decisions on current and future infrastructure development can be made and remedial actions and prevention strategies can be formulated for the problems associated with environmental degradation.

Jan 1, 2011

By Klaus-Dieter Beck

RAG American Coal Holding, Inc. affiliates operate two longwall mines in the Pittsburg seam in Pennsylvania, the Cumberland mine and the Emerald mine. A unique situation in longwall operation occurred at these mines as the mining activities reached the property boundary between the two mines. The retreat direction in the longwall panel in Cumberland mine is West-to-East while in Emerald mine, it is East-to-West. This unique condition required an adequate design for barrier pillar between the two mines to minimizing the mutual effects of longwall retreat when both longwall faces met and an adequate roof control plan for gateroads. Field studies that involved mainly roof-to-floor convergence monitoring were conducted to assess the effectiveness of the employed barrier pillar in isolating the mutual effect of longwall retreat. Three-dimensional finite element numerical modeling was used to evaluate the gateroad roof and pillar stability. The modeling was conducted such that it duplicated the actual mining process as realistically as possible. The modeling results predicted that the employed barrier pillar and the roof control plan would ensure stable gateroad systems in both mines during and after the two longwall faces met. The prediction was confirmed because mining operations in the two longwall panels were completed without any noticeable ground control problems.

Jan 1, 2004

By D. Reddish

The combination of free standing steel supports, such as arches, and rock bolts (mixed support) has Frequently been in used in UK coal mine roadways when it is considered that the strata and/or environmental conditions would not be suitable for rock bolts solely. However, how such mixed support systems operate is not fully understood. Due to the differences in the support method provided by rock bolts and free standing steel, the total support generated is not simply a case of adding the contribution to the support of the roadway given by the two systems. This paper describes a numerical investigation into mixed support systems when used in coal mine roadways. A series of 2D and 3D geomechanical models are described and the method of modelling the rock bolts and steel supports in coal mine tunnels is discussed. The numerical models described include rock boltd only roadways, steel supported roadways and mixed supported roadways in a variety of geological and in-situ stress conditions. Conclusions are formed that allow an insight into mechanisms of strata reinforcement provided by the support systems modelled. Further to this, a review of the numerical modelling of pre-tensioned rock bolted systems is described identifying the contribution to support efficiency given by the adoption of tensioning in full column resin anchors. The results obtained highlight that the effectiveness of the pre-tensioned load is dependant on the rock mass quality and in- situ stress level at the site where it is to be used.

Jan 1, 2004

By Ken Mills

This paper describes the first successful use of hydraulic fracturing to induce caving events "on demand" in Australia. Moonee Colliery operate a longwall immediately below a thick conglomerate strata. This strata temporarily bridges across the extracted longwall panel to create a large area of standing goal' When this standing goat' eventually collapses, the windblast generated presents a significant hazard to men working on and around the longwall face. Hydraulic Fracturing has been successfully introduced to take control of the timing of these caving events so as to eliminate the risk of windblast injury, The longwall face area is completely evacuated during the treatment. Water is pumped into an injection point located in the conglomerate strata above the standing goat. A horizontal fracture is generated and grows outward from the in point, separating the conglomerate strata below the fracture horizon_ At some point the strata can no longer span and a goat fall is initiated. After a treatment, mining can be recommenced with the windblast hazard eliminated.

Jan 1, 2000

By Robert R. Thompson

Retreat pillar mining is highly productive but dangerous. The primary danger during pillar removal is premature caving of the roof. Because the safety of the miners is dependent on successfully controlling the roof, the roof must cave in a predictable and dependable manner. Temporary support during retreat is usually obtained by setting posts. They are set manually by a miner working in a dangerous area. A solution to this problem would be a system which could set and retrieve roof supports remotely and safely. The Bureau of nines has developed a remotely operated Mobile Roof Support (PIPS) machine which will place and retrieve temporary roof support. Two PIPS machines were fabricated under a cost-sharing agreement with Southern Utah Fuel Company and mining equipment manufacturer. Each machine carries four 50-ton jacks and is remotely- Controlled by radio. The machines are presently being used by Southern Utah Fuel Company under a long-team cooperative agreement. Not only have there been material and manpower cost savings in not having to set posts, but also the time saved bas resulted in increased productivity. The projected costs of mass-produced machines with tethered remote control rather than radio remote control are estimated at $150,000 each. The radio remote control is more expensive and is considered an optional extra.

Jan 1, 1986

By S. M. Hsiung

In late September 1984, a longwall panel in West Virginia lost 60 powered supports when the face had advanced for 250 ft. from the setup entry. An in-mine investigation showed that it was a first weighting failure resulting from inadequate Support capacity. This paper presents the results of finite element modeling, which have led to a better understanding of the first weighting failure mechanism. The dynamic impact of the first weighting failure on the powered supports is analyzed. The optimum capacity for the powered supports in order to control the roof at face area under the geological condition is discussed.

Jan 1, 1984