Search Documents

By Tianming Sun, Gabriella Tranell, Ragnhild E. Aune, Mark William Kennedy

Rare Earth Elements (REEs) are critical for the production of many advanced materials and products. Mining and primary production of REEs are generally associated with significant environmental impacts. By recovery of REEs from secondary sources, through recycling or as a byproduct, the adverse environmental impacts may be partly avoided. In the present study apatite concentrate originating from iron ore beneficiation done by LKAB in Kiruna, Sweden, is explored as a possible source for REEs. The composition and distribution of the REEs within the concentrates are studied using ICP-MS, XRD and SEM-EDS/EPMA, as well as the melting point and heat of fusion using DTA-TGA-MS. The behavior of the material during melting has also been studied through wetting and slag saturation experiments. The overall aim of the study is to evaluate the implications for future smelting experiments aimed at concentration and recovery of the REEs.

Jan 1, 2015

By Richard D. Hagni

An enhanced Interest in pyrometallurgical dusts has recently emerged due to increased world-wide environmental concerns. Mineralogical study of dusts samples from lead sinter plants. lead smelters, and secondary steel mill electric arc furnaces has shown that they can be readily studied by reflected light microscopy. These dusts typically are composed of small particles sufficiently large that their mineralogical identification and characterization can be conducted under the reflecting light microscope. Scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS) has been used to confirm optical identifications and chemical compositions. The sinter and blast furnace dusts at the Doe Run Smelter at Herculaneum, Missouri are commonly about 20-150 11m. They consist predominantly of galena, chalcopyrite, sinter. slag. coke. and particles. Dusts from remote sampling sites 112-1 mile from the lead smelter are composed of similar particles and abundant fine-grained particles, less than 10 um. of locally derived calcium-aluminum silicates. Electric arc furnace (EAF) dusts are mostly spherical and less than 10 11m. They consist predominantly of iron oxides (magnetite. franklinite. jacobsite and solid solutions of these spinels), zincite. and calcium-iron silicate glass, together with smaller amounts of hematite. sylvite. coke and metallic iron. Reflected light microscopy is rapid provides mineralogical data on individual grains within dust particles. and allows direct observations of textural intergrowths in pyrometallurgical dust particles.

Jan 1, 1991

By Daowu Yang, Zhuo Ren, Hui Liu

"In this paper, the photochemical catalysis degradation effect of photocatalyst obtained by charcoal-supported nano TiO2 (nano TiO2 / charcoal) on the formaldehyde in the air was studied. The influences of the nano-TiO2 loading and the photoreactor structure on the efficiency of photochemical catalysis degradation of formaldehyde was reviewed.The nano - TiO2 / bamboo charcoal adsorption of formaldehyde, as well as the influences of a certain amount of formaldehyde after adsorption on its photochemical catalysis effect were discussed. The sol preparation process of Ce-doped nano-TiO2 was described. Experimental results indicated that: the surface of bamboo Charcoal still has a strong formaldehyde adsorption capacity after Supported by Nano TiO2.After adsorbing formaldehyde, the photochemical catalysis degradation efficiency of formaldehyde of the catalyst at a steady state is basically the same with new prepared catalysts’. When the thickness of the catalyst layer of the multi-ladder-type structure photoreactor is 2mm, the interval is 20mm, the absorption efficiency of formaldehyde of Nano- TiO2 / bamboo charcoal is the best . Nano-TiO2 undoped Ce responded with no degradation of formaldehyde after 2 hours, while the degradation rate of formaldehyde of the Ce-doped nano- TiO2 reached 15% 2 hours late, and the formaldehyde decontamination of the equipment reached 94%.IntroductionEmerging out of home decoration in the distribution of formaldehyde, benzene, ammonia and other indoor pollutants have been proved to be very harmful to the human body. Photocatalysis can eliminate air pollutants, in particular, can effectively degrade the air volatile organic compounds, it is a new method of air purification developed in recent years. the biggest advantage of photochemical catalysis degradation is green, this method can be available at normal temperature and pressure to degrade formaldehyde and other organic matter into carbon dioxide and water without secondary pollution.Nano-TiO2 have become the most studied photocatalyst due to its stable, non-toxic harmless, superior photochemical catalysis properties [1]. Initially nano-TiO2 powder was used as a photocatalyst, but it’s difficult to recover and easy to wear and tear [2,3]. Later, the TiO2 was used in the form of film loaded on some carriers, such as glass beads [4]. As the photochemical catalysis reaction occurred on the catalyst surface, only the organic matter adsorbed on the catalyst surface can be degraded, so the catalyst was requested that must have a strong adsorption. Combined the adsorption properties of bamboo charcoal and the photochemical catalysis activity of nano-TiO2 together. Made the photocatalyst by loading the nano-TiO2 on bamboo charcoal to degrade organic matter in the air. Nano-TiO2 semiconductor photocatalyst has a strong catalytic oxidation due to the photo generated hole of the surface [5,6],and has a potential application. Some studies have shown that nano-TiO2 photocatalysis activity can be increased by doping certain metal ions [7,8].The aim of our work in this study was to use bamboo charcoal load Ce-doped nano-TiO2 photochemical catalysis oxidation to degrade formaldehyde,and design a multi-ladder structure photoreactor, also prove the availability of the device from the theoretical and experimental."

Jan 1, 2011

By Ricardo Melamed

Metallic mercury has been extensively used for gold recovery. Although the solubility and mobility of metallic mercury is low, this metal can undergo many transformations, leading to mercury contamination in humans. The complexity of Hg chemistry in the environment reflects its different possible oxidation states and species, with different physical-chemical properties. The interaction of Hg in the terrestrial system, as well as in the aquatic environment, is important to understand the mercury cycle. This paper reports data on the adsorption of Hg onto an Oxisol soil. Results show that the interaction of Hg(II) at the soil-solution interface depends strongly on ligand concentration in solution, which can affect Hg mobility. The presence of the chloride anion in solution increases the mobility of Hg(II) through the soil, due to a relative lower affmity of mercury chloride at the oxide surface. In the absence of chloride, Hg(II) form strong complexes with the surface, and its adsorption behaviour is similar to the adsorption of other hydrolizable cations.

Jan 1, 1996

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In order to produce good quality ammonium paratungstate, Sn needs be removed efficiently from the tungstate processing solution. The nascent hydrous ferric oxide has excellent adsorption ability and is often used as an adsorbent to remove metal ions from aqueous solution. In this paper, nascent hydrous ferric oxide is used to remove Sn from tungstate solution. Through experimental, the effects of pH value, reagent amount of adsorbent, reaction temperature and reaction time on the Sn removal are investigated. The study shows that 98% of Sn can be removed effectively from sodium tungstate solution and only 2% of W is lost during process under the conditions of pH 9~12, reagent amount of Fe addition 40 times Sn amount, reaction time 30min and room temperature. As the Fe addition reaches 90 times of Sn concentration in the ammonium tungstate solution, 99% of Sn is removed and APT with zero level purity national standard is obtained.

Jan 1, 2014

By K. R. Robilliard

The Peru based tin mining company, Minsur S.A., commissioned Ausmelt Limited to design, supervise construction and commission a tin smelter and refinery for production of refined tin metal. The plant is located 240km south of Lima, near Pisco, Peru and is operated by Funsur S.A., the wholly owned subsidiary of Minsur S.A.. Selection of the Ausmelt Technology followed a series of crucible scale test work and pilot plant trials conducted at Ausmelt's facility in Dandenong, Australia and two feasibility studies undertaken by Ausmelt in 1991 and 1993. Ausrnelt began the plant design in 1994 with the construction phase following in 1995. Commissioning of the plant commenced early in 1996 with a target throughput of 30,000 tonnes per annum of concentrates. In mid 1998 oxygen enrichment of the Ausmelt lance air was introduced to expand the capacity to the throughput of 40,000 tonnes per annum of concentrates. The process route involves the use of an Ausmelt furnace for primary concentrate smelting, followed by a conventional tin pyro-refining circuit to produce high grade tin suitable for sale. Further work continues between Ausmelt and Funsur to investigate the use of an alternative, more economical, fuel source and the installation of a second Ausmelt furnace. The paper reviews the project to date with details of ongoing operations and developments at the Minsur Tin Smelter.

Jan 1, 2000

By H. V. R. von Rhaden

Systematic quantitative X-ray diffraction analyses performed on diamond-drill cores originating from the Aandenk formation at the Loraine Gold Mine, located in the Welkom goldfield, Orange Free State, South Africa, have revealed the presence of a number of phyllosilicate mineral assemblages which have not hitherto been reported from this region. Rectorite, a regularly interstratified 1:1 mica-montmorillonite "swelling clay", is found to occur together with paragonite, muscovite, pyrophyllite, kaolinite, and chlorite in highly-altered friable rocks. The presence of rectorite in mill feeds may have potentially serious implications with respect to gold recovery. Quantitative X-ray diffraction analysis for phyllosilicates can be used as an aid to correlation, and also to guide the widths of stopes in underground mining. Rectorite has a unique mode of origin, which is discussed.

Jan 1, 1991

By Semih Perdahcioglu, Arthur E. Morris

"The curricula for the majority of Materials Science and Engineering programs is devoid of all but the most rudimentary coverage of the principles of material and energy balance calculations. As a result, graduated engineers that need to make such calculations are faced with three unpalatable options. First, attempt to learn the subject by attending workshops or short courses sponsored by corporations or industry groups. Second, outsource the needed work to a consulting engineering company. Third, purchase a software package that's capable of simulating a process. Each of these options require a considerable investment of employee time and effort. The first option might be the best if suitable computational software was readily available. We review the recent development of such software, which is entirely based in Excel. The software tools include a thermodynamic database, tools for multiple computations, and a flowsheet simulation program. These tools employ teaching by simulation.IntroductionPracticing engineers often come up with situations where they must learn a technical subject that they didn't cover in their college classes. One possibility is to obtain a couple of texts on the subject, and delve in. Or, they may sign up for an intensive short course where they can get personal instruction and guidance. But the first option requires a lot of study time, and the second option may not provide the specific instruction (or intensity of instruction) required to appropriately master the subject. Here we look at ways of using simulation techniques to learn the methodology for making material and energy balances on industrial processes.Industrial heating processes have undergone many changes over the past dozen years, as vendors have introduced new heating equipment designed to recover the greatest possible amount of heat from the fuel, and to meet stringent environmental challenges for emissions (especially NOx). Even though the recent unprecedented drop in price of natural gas may have altered the urgency for improving a plant's energy efficiency, the need is still there. Until recently, there was a dearth of readily-available software for process engineers to use for simulating a plant's flowsheet. The good news now is the existence of several Excel-based software tools that make the calculational process much easier. [ 1]. Plant engineers may also be interested in a DOEsponsored program[2] which allows plant-wide and ""what-if' analyses of the energy balance."

Jan 1, 2013

By Bao Xiancheng

Jinlong's copper flash smelting process started up in April 1997. In the early days of production, lots of equipment and process problems were encountered. But, through continuous improvements in equipment and operation, the designed productivity was reached two years later and the smelting operation has been greatly upgraded since then. After more than 4 yew of production, we have made great achievements, such as increasing the flash furnace availability, significant improvements in operation control, optimization of concentrate burner's structure and operation, and smooth operation of the whole smelter. This paper outlines Jinlong's operational achievements made after commissioning, and discusses problems that were encountered and their countermeasures. Operational experience is also summarized

Jan 1, 2002

By Deyou Yin, Kongfang Feng, Bo Wang, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jinyin Xie

"The flow patterns and mixing characteristics in a water model of C-H2 smelting reduction furnace are experimentally studied in this paper. Water modeling is employed to investigate the features of gas jet stirring and the fluid flow patterns in the bath of a smelting reduction furnace during the top, bottom, and side combined blowing process. The influence of the gas flow rate for top, bottom and side nozzles, angle, submerged depth of each side nozzles and the height of the top nozzle has been examined. It showed that the gas flow rate of side nozzles and bottom nozzle had a key role on the fluid flow and mixing characteristics. The gas jet from the top nozzle could change the agitation and fluid flow pattern caused by the gas jets from the side nozzles in the bath.IntroductionFacing the current natural resources decrease and the environmental degradation, smelting reduction iron-making technique is believed to be the most representative at present. Mid last century, the concept of producing liquid iron or semi-steel directly from ore fines and inexpensive fuel was the subject of considerable pilot plant development activity. Among these projects, the direct smelting process, which is the reduction and melting of iron-bearing materials by carbon and other hydrocarbons in the vessel containing a molten bath, is the most popular one. A number of direct smelting processes have been developed around the world, e.g. COREX, DIOS, HIsmelt, AISI, ROMELT, etc.These studies put forward a new technology, which through bottom nozzle blowing rich hydrogen, top nozzle blowing rich oxygen and provide preheating ore and solvent, side nozzles blowing oxygen-coal to realize smelting reduction iron-making process. Owing to the metallurgy reactions always in high temperature, which is above 1600 °C, it is difficult to visualize the mixing behavior and measure the desired phenomena in the reduction vessel. With water modeling, the primary advantages are that it is relatively easy to observe and measure the flow phenomena in the bath."

Jan 1, 2011

By Katsuyoshi Tatenuma

"In order to mitigate the effect of global warming by preventing the accumulation of atmospheric CO2, a permanent fixation method of surplus CO2 as an insoluble mineral onto the sea bottom is proposed. As the proposed reduction method of atmospheric CO2, the concrete concept of this method is to form an insoluble carbonate mineral (CaCO3) by direct electrolysis of the seawater; Ca2++2HCO3 -+OH- ? ?CaCO3(insoluble)+CO3 2- (soluble)+H++H2O <not as coral reef reaction>, are directly disposed of itself onto the sea bottom. By this treatment, a concentration of carbonate is reduced in the section of superficial seawater, and therefore the absorption capacity of atmospheric CO2 increases depending upon the shift of chemical carbon equilibrium between the mass of superficial seawater and the atmosphere. As no additives are required, or no secondary waste are produced, the proposed method assuming as green-orientated, has possibility to resolve fundamentally the problem of global warming in a green orientate manner.IntroductionRecently, the amount of atmospheric CO2 has been exponentially increasing and it is a main greenhouse effect gas causing the global warming [1, 2]. The concentration of atmospheric CO2 has increased more than 30% (370ppm in 2001) during only last two centuries, therefore approximately 750 Gton-C of CO2 currently exist in the atmosphere, in which 180 Gton-C of CO2 are accounted for the increment during two centuries [1, 3, 4]. In order to avoid the progressive increase of CO2 global abundance, 3 Gton-C of the incrementing amount per year [4], have to be removed annually from the atmosphere."

Jan 1, 2008

By Alicia E. Ares

316 L Stainless Steel samples were solidified directionally under conditions which produced the columnar to equiaxed transition. The position of the transition was located in each sample and the distance from the bottom of the ingot was measured. During solidification the distribution of temperatures were measured by means of thermocouples located strategically. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solidus fronts. Comparing the location of the transition and the values of these parameters it was found that the temperature gradient reaches negative values of as low as -13.44 "C/cm, and velocities of the fronts of around 0.1 cm/s. Also, a supercooling of 5.81°C were measured which was associated with the supercooling for the nucleation and growth of the equiaxed grains ahead of the columnar front. In addition the primary and secondary dendritic spacing was measured in both regions. The spacing was compared with the predictions from available models. The results are presented and discussed in the frame of the results obtained for other alloys

Jan 1, 2002

By Guolin Zheng, Jian Pan, Deqing Zhu, Xianlin Zhou

"In ferronickel production, nickel oxide and part of the iron oxide are reduced to metal by agglomeration and smelting in blast furnace. Due to the physical and chemical properties of the laterite ores, a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality. In this paper, the process of pelletization of nickel laterite was developed, and some parameters to strengthen the pelletization of nickel laterite have been optimized. The results show that the compressive strength of fired nickel laterite pellet can reach over 2000 Newton per pellet while firing at the temperature of 1220 °C~1250 °C in 12 min. The product pellet can be used as high-quality burden for blast furnace to manufacture ferronickel.IntroductionIn recent years, the global stainless steel market was developed exuberantly, which greatly promoted the needs of the basic raw material of stainless steel smelting - metal nickel. Currently nickel sulfide ores are only 40% of global nickel reserves, but offer 60% of all the nickel production. However, with the deficit of resources, the nickel sulfide ore (high grade ore) is depleting, so there is an increasing focus on the utilization of low-grade nickel laterite. Recent research has focused on the wet treatment process to utilize nickel laterite, and less on the use of other technologies [1-8]. The economical and efficient technology relies on the reduction of nickel oxide and part of the iron oxide metal by agglomeration and smelting in blast furnace in China. Some domestic steel companies have adopted this process [9, 10]. Unfortunately a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality of fired pellets. In this study, the process of pelletization of nickel laterite was developed firstly, and some parameters to strengthen the pelletization of nickel laterite have been optimized, and the product pellet can be used to produce stainless steel and ferronickel alloy by blast furnace."

Jan 1, 2011

By J. Bostjancic

As wastewater discharge regulations become more stringent, power plants, manufacturing plants and other industrial sites are looking for ways to reduce makeup water requirements and to recycle and reuse as much wastewater as possible. In some cases, environmental regulations require zero liquid discharge, meaning all wastewater must either be retained on site or reduced to solids for disposal off site. Zero liquid discharge or "closed-loop" wastewater treatment systems using evaporators and other process equipment have been well-accepted in recent years. Often overlooked is the fact that zero discharge is not just the latest fashion--many commercial zero liquid discharge systems have been in operation since the mid-70&apos;s. This paper will give specific examples of zero liquid discharge operations from 1974 to the present, showing how evaporation equipment and processes have changed to meet the requirements of industry and environmental regulations.

Jan 1, 1996

By Peter R. Sanford

Cyanides are present as a dilute constituent of streams from a variety of metallurgical and mineral-processing operations. In addition, a cyanide concentration in excess of approximately 100ppb is toxic to aquatic life, and consequently these operations require a waste-treatment process to reduce the already dilute cyanide species by several orders of magnitude. Furthermore, the waste streams may have flowrates in excess of a million gallons per day. The paper reports on research conducted with a laboratory?scale electrochemical porous (graphite felt) electrode (anode) flow-reactor, which was conducted in conjunction with a computer-aided simulation of a mathematical model describing the intrinsic rate-phenomena associate with the electrode processes. The laboratory-scale cell, of rectilinear geometry, was found to be capable of reducing a feed-stream anolyte (KCN-KOH and supporting electrolyte of a single salt ? K2SO4) with a cyanide concentration of 10ppm, to less than 100ppb, at current efficiencies in the neighborhood of 50%. The computer simulation of the cell performance based on the mathematical model (and constraints imposed for tractability) was found to provide only for qualitative agreement.

Jan 1, 1998

By F. Shahbazian

attempt to systematize the knowledge on slag viscosities, the present work was carried out. The Among the physical properties of slags, viscosity is very important in understanding the mass out in the temperature range 1438-1762 Q The rotating cylinder method was used in the viscosity measurements. Crucibles and spindles made out of pure iron were employed. The transfer phenomena in metallurgical processes. The viscosities of fayalitic slags are of great interest in the non-ferrous metal industry, with special reference to copper production. In an slags were prefused before the measurements. In order to take into account the vaporization reactions involving CaF2, pre- and post measurement samples of the slags were chemically analysed and the compositions were ascertained. The results show that in the case of the CaO-SiO2 system, CaF2 additions tend to decrease the viscosity, in accordance with the expectations. In the case of the "FeO"-SiO2 system, at higher "FeO" / SiO2 ratios in the slags, a reverse trend was observed. The results are discussed on the basis of a viscosity model for silicate melts developed in the present laboratory as well as the structural considerations of silicates.

Jan 1, 2000

By Na Wang, Chao Du, Hongmin Zhu, Kai Huang, Shuqiang Jiao

"Niobium aluminides were directly synthesized by a sodiothermic reduction process of NbC15 - AlCb which was dispersed into LiCl - KCl - NaCl - CaCb melts. The melt supplied a homogenous reaction medium which was substantially beneficial to the co-reduction of Nb and Al to form niobium aluminides in situ. The reduction was performed at 500°C for 4 hours. The products were analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM). The corresponding results indicated that niobium aluminides powders were successfully synthesized.1. IntroductionNiobium aluminides have received considerable attention as high-temperature structural materials, due to their high melting points, relatively low density, high strength, excellent oxidation and creep resistance [1-4]. Figure 1 shows that there are three intermetallic compounds in the Nb - Al binary [5], which includes Nb3Al (A15 structure, Cr3Si type), Nb2Al (D8b structure, cr-CrFe type) and NbAb (D022 structure, TiAb type). These niobium aluminides have been used in turbine blades or in stationary gas turbines [6-8]. However, despite their attractive features, the ir applications are still limited by the long and costly fabrication process [9, 10].Niobium aluminides were industrially fabricated by the mechanically alloyed process [11-13]. Traditionally, niobium is extracted from Nb2O 5 or K2NbF7 by a metallothermic reduction process while aluminum is produced by the Hall-Heroult process of Ah03 electrolysis. Based on the extraction of Nb and Al, respectively, niobium aluminides is synthesized by a mechanical powder alloying process. The present process for making niobium aluminides requires a set of complicated equipment, has high production cost and time consuming [14, 15].The purpose of this work is to present the simple, economic and direct synthesis of niobium aluminides powders utilizing a sodiothermic reduction from NbC15 - Al Cb dispersed into molten salts."

Jan 1, 2011

By Zhihao Yue, Honglie Shen, Yahui Teng, Ye Jiang

"In this paper, manganous nitrate [Mn(NO3)z] was used to assist the etching of silicon wafer in hydrofluoric acid (HF) for the antireflective application, and alumina (Al2O3) layer was deposited on the surface of the etched sample by atomic layer deposition method for further antireflection. The surface morphological and compositional studies of these samples were performed by scanning electron microscopy attached with an energy-dispersive X-ray spectrometer. The surface reflectance measurements were carried out using UV-Vis-NIR spectrophotometer. Binary structures of pyramids and nanopores were obtained by etching the alkaline textured monocrystalline silicon wafer in HF and Mn(NO3)z mixed solution for not more than 15 min. But excessive increase of etching time of up to 30 min resulted in the whole destruction of pyramids. The average reflectances of the 5-min-etched sample before and after being coated with 75-nm-thick Al2O3 layer are 4.62% and 3.47% in the range of 200-1000 nm, respectively.1. IntroductionAs we know, the reflectance of silicon wafer after being sliced is so high that the maximal photoelectric conversion efficiency of silicon based solar cells is limited. Therefore, alkaline texturization process was used for silicon solar cell in industrial production. But the reflectance of this alkaline textured wafer is still greater than 10% and this process can only be used for monocrystalline silicon solar cell."

Jan 1, 2013

By R J. Singh, E. Z. Chacko, Devilal, S. K. Jha, Rina Sahu, Sheshank Shekhar

"Breakouts are one of the biggest problems encountered during continuous casting of steel billets. Billets get cracked locally or break completely in two parts during solidification causing the liquid part of the partially solidified billet to empty inside the cooling chamber. Proper control of important parameters is necessary to avoid break outs during continuous casting. In the present work, the nature of the break outs at a billet caster at Tata Steel was studied. Data analysis was also done for certain casting parameters and the Sulphur tracer test was conducted to understand solidification in the mould. It was found that to reduce the occurrence of break outs, it was necessary to tune the operations based on the grade being cast and the design of the mould tube being used.IntroductionA break out during the continuous casting process is a rupture of the partially solidified shell inside the secondary cooling chamber, causing the contained liquid steel to spill out. In the mid 1970s while continuous casting technology was still in early stage of development, causes of breakouts was not well understood. Today, with technological development much has been understood about breakouts but, most of the understanding has been in the slab casting process wherein due to the higher level of instrumentation, a lot of information has been gained. In billet casting however, due to the geometry of the mould housing with the tube mould, multiplied by the complexity of the multiple strands, instrumentation has not been used and obtaining data for analysis has been difficult.Breakouts at billet casters are still the main hindrances to production. A break out results in a loss in production since the strand which has had a break out is now not available to produce and thus a six strand caster would be reduced to a five strand caster, increasing the time for casting the same tonnage. Additionally extra set up time is required as more often than not a mould change is required in order to have the strand casting again."

Jan 1, 2014

By Nina Bianco, Diana Drinkwater

MetSkill is a professional development program for metallurgical engineers that integrates with normal duties in their first one or two years of service. Graduates work together on a structured technical project, facilitated by specialists and supported by formal learning, and ultimately reported to their technical managers. The program enables graduates to “fill the gaps” in their undergraduate education, which is increasingly pertinent as engineering degrees become more general. Participants report that they enjoy the focus on more challenging (rewarding) aspects of their jobs and feel more confident about problem solving. Sponsor companies add that the relationships developed with external technical specialists enhances opportunities for innovation and development. MetSkill was delivered to two major resource companies in Australia in 2012. This paper provides an outline of the program and the reasons for its success, and demonstrates how the learning model could be applied to groups of graduates in other engineering disciplines.

Jan 1, 2014