Search Documents

By A. G. Cecutti

A brief overview of the known significant health effects of both Nickel and Cobalt will be presented. Some time will be given to the current research activities, especially for Nickel. Emphasis will be placed on some of the controversial issues associated with their health effects.

Jan 1, 1988

By B. R. Baldock

The converting of high-grade nickel matte for production of low-sulphur matte or nickel metal is a process which has eluded metallurgists in the past because of the limitations of conventional converting furnaces. The high temperatures required and the refractory nature of nickel oxide has prevented practical success in a process which has been known to be theoretically feasible for a long time. The Ausmelt top submerged lancing system is capable of operating under close control of the smelting conditions. High temperatures and both rapid oxidation and rapid reduction can be achieved. These features have provided the basis for successful pilot plant trials of the desulphurisation of high-grade matte from the Kalgoorlie Nickel Smelter. Sulphur level in product was lowered from 20 to 25% to as low as 0.2%, with iron levels in matte in the range of 1.0 to 3.5%. The theoretical background of matte desulphurisation is surveyed and the pilot plant operations described. The implications of the results in relation to commercial plants and possible refinery operations are summarised.

Jan 1, 1993

By A. Erçin Ersundu

In the present work, three different domestic iron ores; Sivas Divrigi B Head high grade hematite lump ore, Malatya-Hekimhan-Hasançelebi medium and low grade magnetite lump ores reduced with Soma-Kisrakdere lignite coal to investigate their suitability for sponge iron production. A laboratory scale box furnace was used to carry out the reduction experiments. In the experimental studies different operation parameters were selected being Cfix/Fetot. ratio, temperature in the range of 1100 - 1250 oC and time, to determine their effects on metallization. Metallization degree up to 90 % was found in the reduction experiments realized by using Sivas Divrigi B Head high grade hematite lump ore, whereas for Malatya-Hekimhan-Hasançelebi medium and low grade magnetite lump ores 60 - 65 % metallization degrees were obtained.

Jan 1, 2008

By Hideaki Tokuyarna

Recovery of metal such as V, Ni and Fe from oil fly ash is important for efficient use of natural resources and protection of environment. Leaching of metals from fly ash followed by ion exchange of leached metals has been examined to develop a process which can selectively recover V and Ni from the fly ash. Experiment of leaching with water, HCI, H2S04 and NaOH leads us to propose a two-step leaching process as an effective and mild operation. The first step is leaching with water for removal of Ni, Mg, A1 and Zn and the second step is leaching with acidic solution for the recovery of V. The metals V and Ni are then separated from other metals in each leached liquor by ion exchange. Advantage of this separation process is that acidic leachant can be reused, which contribute to save separation energy.

Jan 1, 2002

By S. P. Rivers

The stainless steel industry re1ies on nitric-hydrofluoric acid (HNO,/HF) pickling solutions to remove surface contaminants and maintain the corrosion resistance of the steel. More stringent environmental guide1ines are expected to be placed on the disposal of these solutions which could significantly increase processing costs. The U.S. Bureau of Mines has been conducting research to develop a process for recycling depleted pickling solutions, thus reducing the quantity of by product acids generated. Research has shown that F- can be liberated from the predominant iron fluoride species (FeF,') by using oxalic acid in an electrodialysis cell. Ion selective membranes allow dissolved metals in the depleted solution to be replaced with hydronium ions by metathesis, thereby regenerating the HF. The regenerated HN03/HF is then retained in the pick1ing solution. This paper reports on the research effort at the U.S. Bureau of Mines Rolla Research Center to apply electrodialytic recycling to HN03/HF pickling solutions.

Jan 1, 1993

By Sepp Härkki

The energy crisis in Finland after World War I1 together with a sharp rise in the price of energy caused Outokumpu Oy to consider replacing the electric furnace smelting of copper concentrates by some other method. The flash smelting method developed under these circumstances offered a considerable saving of fuel through the utilization of the reaction heat of sulphides and yielded a high recovery of sulphur in the form of acid. The pilot plant testing of the new process was carried out in the years 1947 - 1948. The process was adopted for the smelting of copper concentrates (1) (2) (3) on a commercial scale in 1949 and applied successfullv to the smelting of -nickel concentrates' at the Harjavalta Works in 1959 (4) (5) (6). In 1962 Outokumpu adopted another type of flash smelting where elemental sulphur is recovered from the gases after the thermal decomposition of pyrite in the flash smelting furnace (7) (8): In recent years, the copper-nickel flash smelter and pyrite process have been combined to produce elemental sulphur instead of SO2 from the smelter gases (9) (10). The basic idea of the Outokumpu flash smelting process for sulphidic ores is that the conventional methods with separate roasting and smelting operations are replaced by a combined roasting, smelting and part-converting process carried out in one unit. The heat generated from the exothermic reactions can thus be used for smelting the ore so that only a small amount of additional fuel is needed. The characteristic of the method is also that the dried, fine-grained concentrate is smelted in suspension, which offers the best conditions for rapid reactions. The recovery of waste heat from the furnace off-gases had been considered already in the original flash smelting system. A

Jan 1, 1976

By K. Robinson

Following the longest Smelter campaign in BCL?s history it was planned to completely rebuild the flash smelting furnace in 1987. This was the fourth major overhaul and the most extensive so far attempted. Detailed planning took place over several year$ preceding the shutdown and implementation was completed in 54 days. The key to minimising shutdown time was the method designed for installation of the new uptake shaft and reaction shaft. Major repair work was also undertaken in the waste heat boiler and electric furnaces. Both of these activities had an impact on the critical path of the flash smelting furnace overhaul.

Jan 1, 1993

By Yuan Zeping

The distributions of impurities in the copper melt, the slag and the gas phase in copper flash smelting process were under study in the Guixi smelter, particularly during operating conditions of high oxygen enrichment with production of high grade matte. Several methods for the removal of impurities such as As, Sb and Bi in the copper smelting process were developed and implemented at the Guixi smelter. This paper described the effects of high oxygen enrichment, elevated matte grade, high temperature and high production rate on the distribution of impurities, methods adopted at the smelter for the removal of impurities, and the associated benefits in the utilization of these removal techniques which include the mathematical model for material blending, high thermal intensity operation at the flash furnace, extended converter blowing, and injection of slag modifiers consisting of Na2CO3 and CaO powder mixture to the converters and anode furnaces.

Jan 1, 1999

By Kurt Westerlund

Three. years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm /h at Boliden Ronnskar Sweden on a TBRC smelting palena (PbS). Operating experience from the Kivset flash WHB 11.900 nm /h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3 /h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By Yuanbo Zhang, Yingming Chen, Zijian Su, Bingbing Liu, Jun Chen

Iron, tin-bearing tailings is a kind of hazardous solid waste generated from cassiterite dressing operation. It is difficult to utilize the tailings by present mineral processing methods due to the complex dissemination characteristics. In this study, a process of gas-based magnetizing roasting followed by magnetic separation was studied for separating and recovering iron from the tailings. The effects of roasting and magnetic separation parameters on the recovery of iron were systematically investigated. The optimum parameters were proposed as follows: CO/(CO+CO2) content of 5%, roasting temperature of 850 C, roasting time of 60 min, grinding particle size of 90% less than 45 μm and magnetic field intensity of 800 Gs. Under these conditions, the magnetic concentrate containing 68.5% Fe and 0.06% Sn was achieved, which can be used as high-quality raw materials for direct reduction iron production.

Jan 1, 2016

By Kenichi Moriyama

The Sumitomo Toyo Copper Smelter started operation in 1971, as an epoch-making smelter at which 9996 of the charged sulfur could be captured. In the past ten years, the amount of treated copper concentrate has-been increased from 1,300 l/ day to 1;900 t/ day by the extremely effective application of the oxygen enrichment for a flash smelting furnace and converter furnace. The sulfuric acid production capacity at the acid plant has also been increased up to 1,900 t/ day corresponding to the increase of copper concentrate smelting rate without installing an additional acid plant. Furthermore the sulfur fixed ratio is kept at a high level, more than 99.996. despite the SO. strength fluctuation of the wide range of 596 to 1396 which is attributed to the combination of flash smelting furnace and, P.S. converter. These -operational results at the? acid plant were achieved by several modifications. and two examples are briefly described as follows; (1) Converter modifications in order to cope with the high SO, strength -gas (2) Introduction of the anodically protection shell and tube type acid coolers In addition. the quality of sulfuric acid has been positively increased. For example, the concentration of iron and arsenic, which were the main Impurities in ?sulfuric acid, was successfully .reduced.

Jan 1, 1995

By Alex Moyano

At present, the Codelco Norte smelter processes in the Teniente Converter and the Flash smelting Furnace 1,420,000 t/y of its Chuquicamata concentrate with an arsenic content of up to 1.5%. In a near future Codelco-Chile is considering different processing options for a new projected concentrates from the Alejandro Hales mine (former Mansa Mina mine with an arsenic content of up to 6%). The main option is the possibility to process 3,000 t/d of mixing concentrates from the Alejandro Hales and the Chuquicamata mines, in the Teniente Converter. The main feature of this smelting unit will be high volatilization of arsenic when processing high arsenic-bearing concentrates. The CN smelter staff carried out a technical feasibility study to evaluate the processing of high arsenic-bearing concentrates directly in the Teniente Converter, thus the low arsenic-bearing concentrates can be processed in the FSF. Accordingly, laboratory scale tests were carried out at the Tohoku University facilities. The lab-scale results allowed an industrial scale test at the Codelco Norte smelter to smelt 2,300 tpd of high arsenic-bearing concentrates in the TC and evaluate the metallurgical impact in the smelting, converting and refining areas of the smelter. The main industrial-scale result confirmed the stabilization of the arsenic content at 0.5% in the 70% Cu produced white metal at the test condition.

Jan 1, 2006

By M. A. Barron, D. Y. Medina, R. T. Hernandez, I. Hilerio

"Chromium Nitride (CrN) thin fihns were deposited on steel AISI 316 substrates with reactive magnetron sputtering method. CrN films were produced under two different conditions. In the first one, the substrate was heated by a d.c. source. At the second coating was applied a negative substrate bias voltage. X ray diffraction, quantitative energy dispersive and scanning electron microscope, were employed to characterize their phases, chemical composition and microstructure. Additionally microhardness was evaluated using a microhardness tester. The results show that the phase formation of CrN thin films in the first case (with temperature) is better. Both coatings presented homogeneous surface. Their compositions shows differences though that gases flow are same. In attention to their hardness, presents an increment if it's compared with hardness substrate.Nomenclature.P Ar =Argon gas pressure during coating.PN2 = Nitrogen gas pressure during coating.Ts = Substrate temperature during coating.T f = Coating melting temperature. (CrN = 1050°C).E=Potential difference.t =Coating time.P=Target power (Cr) in magnetron sputtering de.HV = Vickers hardness.F = Applied charge.d= Average length of longitude of the two diagonals (mm)Introduction.Wear causes losses in materials surface, generating that components of mechanical systems suffer irreversible changes in their properties, causing a faulty operation of the system. It is important to control their effects, measuring and interpreting their causes clearly."

Jan 1, 2013

By Goran Vukovic

The use of gas purging plugs in the copper industry is a widely used practice. They provide substantial improvements especially in anode refining furnaces, where savings in process time and energy are obtained as well as refractory wear and buildups inside the furnace are minimized. The newly developed system, enables purging plugs to be implemented in both stationary and tilting furnaces, is in operation in vessels on three continents. An additional advantage in these furnaces above all other benefits is the significantly improved melting rate. This innovative and patented gas purging system consists of a purging plug cooling device and a slidable, cooled piping system. It provides compensation for any thermal expansion in the furnace lining and minimizes the risk of undesirable copper infiltration. User experiences and results of this widely used system are reported in this paper.

Jan 1, 2014

By Metehan Erdogan, Ishak Karakaya, Fuat Erden, Emre Ergül

"The FFC Cambridge process was suggested as a promising Si production technique for the expanding solar energy industry. Direct electrochemical reduction of bulk SiO2 plates and porous SiO2 pellets in molten CaCl2-NaCl salt mixture were investigated at 750°C by applying 2.8 V potential difference. The produced Si powder was brown and found to be contaminated by the Ni and stainless steel plates used as the cathode contacting materials. The reduction rates of the bulk SiO2 plates and porous SiO2 pellets were compared from variations of current and accumulative electrical charge that passed through the cell during the electrochemical reduction. The amorphous bulk SiO2 plates were reduced slightly faster than porous pellets of crystalline SiO2. The overall reduction potential of SiO2 pellets against the graphite anode at 750°C in molten CaCl2-NaCl salt mixture was determined as 2.3 V by cyclic voltammetry. This potential was supported by calculations.IntroductionMetallurgical grade Si cannot be directly used in electronic industry and some intermediate steps are required to produce industrial solar grade silicon (SOG-Si). A promising alternative solar grade silicon production technique is the FFC Cambridge Process [1]. Production of Si by electrochemical reduction of SiO2 at 850oC in molten CaCl2 electrolyte was first studied by Nohira et.al. [2]. In their study; Si formation was observed on bulk SiO2 cathodes after 1 hour of electrolysis. Complete electrochemical reduction of porous SiO2 pellets was first reported by Jin and his coworkers [3]. The mechanism of electrochemical reduction of SiO2 to Si in molten CaCl2 was explained in another study [4]. Reduction rates of bulk SiO2 and porous SiO2 pellets were also compared previously and it was found that reduction rates for bulk plates were higher [5]. Furthermore, it was reported that mixing Si into porous SiO2 pellet increased the reduction rate [5]. Mo [2, 4-7], Ni [3, 8, 9] or Si [6] were used as cathode contacting materials in various studies. Yasuda et. al. [6] produced Si with 99.80 % purity using Si plates as cathode contacting material to reduce metal contamination."

Jan 1, 2012

By Zhongliang Tian, Yun Cheng, Yexiang Liu, Ming Jia, Yanqing Lai

"A fundamental electrochemical study of Si ions in Na3AlF6-LiF melts and electrolysis using liquid cathodes was conducted. Cyclic voltammograms (CVs) clearly showed the depolarization of silicon deposition on liquid cathode by forming chemical complexes with the liquid solvent metals. Besides, co-deposition of Al and Si is possible when Si ions are insufficient in the molten salt. Based on the electrochemical results, silicon diffusion into liquid cathode is modelled and evolution of Si activity with concentration is deduced by a mathematic approach. Electrochemical study using liquid metals as working electrodes, can be used as an alternative approach for the acquisition of basic data on alloy behavior. Galvanostatic electrolysis showed that liquid cathodes are appropriate to collect the deposited solid silicon and the highest collection efficiency is almost 85%.IntroductionRecent years have witnessed an increasing demand for solar-grade silicon (Si) by the photovoltaic industry [1-4]. The preparation of high-purity metals through electrolysis and electrorefining offer many advantages such as low cost, low-energy consumption, and environment-friendly process, and thus has been widely used worldwide. From the perspective of electrochemistry [5-7], by utilizing the electronegativity difference between the impurities and Si and controlling the relevant process parameters, it is possible in principle to electrodeposit monatomic Si from a Si4+-containing compound melt. Moreover, because the carbon content of the high-purity Si obtained through electrolysis can be effectively controlled and used as a very ideal raw material in the preparation of electronic-grade and solar-grade Si, the preparation of high-purity Si through electrolysis has received widespread attention [8,9]. Monnier et al. [9] used a graphite electrode to obtain high-purity Si (99.9 %-99.99 %) from Si02/Na3AlF6 system through electrolysis; however, because the Si was precipitated in a solid form and showed poor conductivity, the deposition rate was too slow. Olsen et al. [10] obtained high-purity Si films via electrodeposition in K2SiF6/KF-LiF system by selecting electrode materials with high surface quality (such as Ag and graphite). However, in order to ensure the film quality, the deposition current density must be relatively low (10-50 mA/cm2), resulting in a low current efficiency and low deposition rate, which are not conducive to reducing energy consumption and applying to practical use"

Jan 1, 2014

By James B. Pfeiffer

TETRA Technologies, Inc., has applied its HDS? metals precipitation system to control a mine drainage problem. The effluent from the mine contains primarily zinc, manganese and iron, plus varying small amounts of cadmium, copper and lead. The flow from the mine averages 350 gpm, and varies considerably depending on season and weather conditions. The plant was designed to treat 1000 gpm of the water and generate a dense sludge suitable for recycling. The HDS? system contains a number of reactors, followed by post filtration and meets stringent metals discharge criteria as specified by New Source Performance Standards.

Jan 1, 1994

By David Cocke

Study of surface and subsurface interfacial chemistry of metallic and similar systems has its enormous technological importance. Copper, for example, is a common component of many alloys and bulk amorphous systems. It is being increasingly studied today because of its use for electronic interconnect systems where processing is done below 200 ºC. Since several types of copper oxides exist, and the degree of their formation is dependent on temperature, perhaps characterization by EDS-SEM depth profiling and EIS might delineate one type of oxide from another. In this paper, we described our work on transformation of copper oxides with temperature ranging from 70 to 350 °C and their characterization by SEM, EDS, and XRD. We also showed the use of the phase angle portion of the impedance as a means to identify the predominant structure and the transition through Cu3O2 between the predominant stable CuO and Cu2O.

Jan 1, 2009

By Tao Zhang, Wen-tao YU, Hai-bin ZUO, Jian-Liang Zhang

Sintering-pot tests and metallurgical performances of sinter with 4 kind of different Al2O3 contents are experimented in this paper. Results show: when the Al2O3 contents increase from 2.0% to 3.5%, acicular calcium ferrites in mine phase will be gradually replaced by plate-like iron calcium. The increase of Al2O3 contents will lead to the addition of liquid viscosity and the reduction of permeability of sinter bed. Sintering time will be prolonged. The rate of yield is stable basically but production is low; besides, the increase of liquid viscosity will decrease of drum strength. The change of permeability of the material layer will make RDI +3.15 decrease first and then increase when Al2O3 contents changed from 2.0% to 3.5%. RI of sinter shows a contrary trend because many open voids are formed by deterioration of liquidity first and then pores closed.

Jan 1, 2015

By K. Krishnapisharody, G. A. Irons

"The modeling of gas-liquid plumes in steelmaking ladles has been the subject of many investigations. In most studies, the “modified” Froude number, based on the momentum of the injected gas, has been employed to characterize two-phase plumes. This approach has several shortcomings and is critically reviewed in the present work. Based on an extensive review of previous work and theoretical considerations, it is demonstrated that the injected momentum and consequently, the modified Froude number has no significance to gas blowing operations in Ladle Metallurgy. Instead, an approach based on the “plume” Froude number, previously shown by the authors as the proper form for Froude similarity, is extended as a simpler alternative.IntroductionGas injection is central to most Ladle Metallurgy operations. During ladle processing, the steel melt is usually stirred by an inert gas like Argon through porous plug(s) fitted in the bottom of the ladle or a lance inserted deep into the melt. The purging serves several purposes viz., homogenizing the melt, flotation of inclusions, enhancing the rates both of refining reactions and dissolution of alloying elements and promoting inter-phase interactions in the ladle.The topic of gas injection into liquid baths has been the subject of several investigations in the past. A great deal of this work, both experimental and computational, was devoted to describing the structure and properties of two-phase plumes as reviewed recently [1]. Generally, the ascending two-phase mixture is sub-divided into three distinct regions [2]: the jet core, transition and the bubble plume, respectively. The jet region, where the momentum of the injected gas is transferred to the bulk liquid, is also called the ‘momentum region’. In a similar manner, the plume is called the ‘buoyancy region’ where the motion of liquid is caused by the buoyancy force exerted by the bubbles. The proper characterization of these regions is important for the analysis and modeling of stirring operations in Ladle Metallurgy. Although many mathematical correlations exist for this purpose, some issues of theoretical and practical interest to the modeling of gas-liquid plumes need further attention."

Jan 1, 2012