Search Documents

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009

By Qian Xu, Guangshi Li, Xionggang Lu, Xingli Zou, Hongwei Cheng, Cong Xu, Changyuan Lu

The roasting of nickel-bearing sulfides is a complex but important process which has not been adequately characterized. Combination of X-ray diffraction and scanning electron microscopy has been proved to be useful for such experiments. The leaching results of nickel, copper, iron and cobalt was analyzed by ICP methods. Process possibility of polymetallic sulfide concentrates through a three-step procedure (oxidation roasting - chlorination - water leaching) was suggested. Ammonium chloride could react with nickel/copper oxides to produce intermediate complexes. At the temperature range of 280~340 oC, these complexes further decomposed to the corresponding simple chlorides. Roasting sulfide concentrate using NH4Cl is effective for complex ores.

Jan 1, 2016

By Kumar M. Lyer

The channel reactor for ferrous and nonferrous processing has been modeled as a combination of ideal reactors. Cold model studies simulated the counter-current flow of slag and matte (or metal) with high-strength submerged gas injection. A composite model has been developed which describes the mass transfer between the two liquid phases, including the transfer of minor elements. The residence time for the matte droplets in the matte/slag emulsion is compared with the settling rates for the matte droplets in the slag to determine their relative importance in the mass transfer between matte and slag. The governing equations for mass transfer have been developed using correlations for the mass-transfer coefficients in the continuous and dispersed phases. An application of this scheme to a typical copper smelting system is presented.

Jan 1, 1993

By Srinath Viswanathan, Adrian Sabau

"In general, the occurrence of microporosity during metal casting is due to the combined effects of solidification shrinkage and gas precipitation. The governing equations for fluid flow and hydrogen evolution indicate that porosity formation and fluid flow are strongly coupled. However, in most studies on microporosity, it is considered that the porosity formation does not influence the fluid flow in the mushy zone. In this study, a computational methodology is presented for the numerical simulation of interdendritic fluid flow and microporosity evolution. The solution algorithm presented includes a fully coupled, implicit treatment of microporosity and local pressure in the mushy zone. The effects of microporosity evolution due to the local pressure drop in the mushy zone, and pore expansion in casting regions where liquid feeding alone cannot compensate for the solidification shrinkage are also considered. It is shown that neglecting the effect of porosity formation on the pressure in the mushy zone yields higher pressure drops. By its growth, microporosity partially compensates for the solidification shrinkage, reducing the feeding demand. A reduced feeding demand requires less fluid flow to compensate for solidification shrinkage, and results in smaller pressure drops in the mushy zone. Therefore, in order to accurately describe casting defects, comprehensive models of fluid flow, heat transfer, and solidification must include the effect of microporosity as well.IntroductionIn the terminology commonly used by foundrymen, porosity is usually considered to be either ""hydrogen"" or ""shrinkage"" porosity. Hydrogen porosity is the term given to porosity that is generally rounded, isolated, and well distributed. Porosity that is interconnected or clustered, and of an irregular shape corresponding to the shape of the interdendritic region, is usually termed shrinkage. In general, the occurrence of microporosity in aluminum alloys is due to the combined effects of solidification shrinkage and gas precipitation [1]. Continuum models [1, 2- 7] have been used to predict the level of porosity in castings. A number of other studies have also attempted to understand the phenomena of porosity formation and pore growth [8-10] and pore morphology [11].The governing equations for fluid flow and hydrogen evolution indicate that porosity formation and fluid flow are strongly coupled. However, in most studies [4, 9, 10], it is considered that the porosity formation does not influence the fluid flow in the mushy zone. Kubo and Pehlke [3] presented a methodology for the prediction of microporosity distribution in shaped castings by considering the effects of both the hydrogen precipitation during solidification and the pressure drop in the mushy zone. In their approach, the local pressure and porosity were computed in an uncoupled manner based on a ""flux of interdendritic liquid"" criterion, i.e., either pressure or porosity was first computed using the other variable at the previous time step. Their approach has been used with little change in numerous studies [6, 12, 13]. Recently, Kuznetsov and Vafai [14] presented a fully coupled, one-dimensional model for the computation of pressure and porosity. They showed that neglecting the effect of porosity formation on the pressure in the mushy zone yields higher pressure drops and an over-prediction of final porosity. They also showed that the influence of porosity formation on the pressure is larger at lower pressures in the mushy zone."

Jan 1, 2001

By David B. Dreisinger

Mass and heat balance modeling is a powerful tool for the design and analysis of hydrometallurgical process flowsheets. In this first of two papers, we examine the basic fundamentals of mass and heat balance modeling, and apply these concepts to several flowsheets using a simple spreadsheet model. In this way, we aim to demonstrate how such models are not only easy to construct, but can also be indispensable for comparing various flowsheet alternatives, for making rational economic decisions, and for developing a basic understanding of existing process behaviour.

Jan 1, 2002

By G. L. Watt

Fine sized titanium diboride (TiB2) powders have been synthesized in a thermal plasma reactor. Precursor for the synthesis were rutile, boron oxide, and methane. The effect of plasma gas type, precursor ratio, and input power on the synthesis was studied. The produced powders were characterized by X-ray diffraction and chemical analysis. The purified powders were CIP'd, HIP'd, sintered and characterized for porosity, hardness, and microstructure and the results compared with a commercially available TiB2 powder sample.

Jan 1, 1995

By R Bartlett

Process engineering-science originally developed for percolation leaching of ore in heaps is extended to the decontamination of unsaturated soil, either in situ or after excavation and emplacement as a soil heap on an impervious pad. Phenomena considered include: soil matrix porosity and permeability; percolating solution retention, capillarity and flow; washing sweep efficiency; optimum solution application rates during leaching; soil agglomeration to improve soil permeability and soluble contaminant transport by diffusion in soil agglomerates. Practical aspects briefly discussed include leach pad construction, solution distribution and recovery from the soil, and solution containment.

Jan 1, 1994

By R. G. Reddy

Industrial copper reverberatory furnace slags were treated by high temperature techniques (sulfide and carbothermic reduction) to recover copper in alloy or matte phase at 1473K. Recovery was investigated for the condi¬tions of varying amounts of metallic sulfide, carbon and CaO additions. The results showed that recovery of copper increased with increasing amounts of carbon addition, and also is strongly dependent on the initial concentration of copper in the slags. Copper recovery for both carbothermic reduction and sulfide treatment were modeled with linear relationships as follows: for carbothermic reduction (%Cu recovery) = 9.0 (%Cu in slag)initial 73.8 and for sulfide (%Cu recovery) = 7.1 (%Cu in slag)initial 82.2 Higher copper recovery was obtained with sulfide treatment than with carbothermic reduction of slags.

Jan 1, 1983

By Benoit DeBecker

Laboratory-scale experiments have shown that chromium metal could be recovered from chromate wastes by modifying slightly the chromium electrowinning flow-sheet. After reduction by sulhr dioxide and precipitation of chromic hydroxide, the solid residue is dissolved in the chrome alum solution and the metallic impurities are removed by cementation on manganese. The presence of dissolved manganese in the electrolyte does not affect the cathodic deposition of chromium and it eliminates the anodic production of Cr(V1).

Jan 1, 1994

By T. H. Jeffers

The U.S. Bureau of Mines' Salt Lake City Research Center. has developed porous polymeric beads containing immobilized non-living biological materials for extracting metal contaminants? from wastewater&. Immobilized biological materials include peat moss, algae, biological polymers, and other materials that demonstrate high .affinities for heavy metals. The beads, designated as BIO-FIX beads, have distinct advantages over traditional methods of utilizing biological materials in that they have excellent handling characteristics . and can be used in conventional processing equipment or low-maintenance systems.. Toxic metals such as copper, cadmium, zinc, lead, and mercury are several of the many heavy metals effectively removed from mine wastewater& using B'IO"FIX beads. Continuous cyclic testing indicated that the beads continued to produce treated effluents which met National Drinking Water Standards (NDIJS) after 175 loading-elution cycles, Adsorbed metals were removed from the beads using dilute ?mineral .acids. In many cases" the extracted metals were further concentrated to enable processors to reclaim the metals, thus minimizing the generation of a hazardous sludge. Tests indicated that use of the beads in a low-maintenance system was particularly effective for treating remote acid mine drainage waters? and small toxic seeps from hardrock mining districts ..

Jan 1, 1991

By Y. A. Chang, J. Woodford, C. R. Kao

Reactive diffusion studies between NbC and Si were carried out at 1300 °C under a vacuum of 10-5 torr and a uniaxial pressure of 1 MPa. The annealing time ranged from 8 to 100 hours. The Si used was single crystal silicon; the NbC was hot-pressed powder compact. A NbSi2+SiC two-phase reaction layer formed with NbSi2 as the matrix and SiC as discontinuous particles. The microstructure of the reaction product is homogeneous, dense, and fine. The NbSi2 grain size and SiC particle size are in the micron range. The growth of the reaction products follows parabolic kinetics. Extrapolation of the data to zero thickness suggests an apparent incubation time of 3.5 hours. However, for short annealing time «60 hours), the thickness data can be approximated by linear kinetics with an initial growth rate of about 2 11m/hr. Based on these experimental observations, a growth mechanism for the reactive diffusion between Si single crystal and NbC powder compact is proposed. We propose that the nucleation sites for the SiC particles are at the voids of the NbC powder compact. This proposed nucleation mechanism offers a potential way of controlling the SiC particle size by changing the void size and void density of the NbC powder compact. This hypothesis, if proven to be true, will allow us to control mechanical properties of the composites by tailoring the SiC particles formed. It is also pointed out that the microstructure requires Si to be the dominant diffusing species and to diffuse through the reaction layer, while Nb and Conly have to undergo local rearrangement.

Jan 1, 1996

By Bror Nyrnan

Solvent extraction technology and equipment have been developed within Outokumpu since the early seventies. During this period altogether nine solvent extraction processes for molybdenium, zinc, rhenium, cobalt, nickel, calcium and magnesium have been commercially adopted in Outokumpu's metallurgical plants. During last years a new mixer-settler concept based on a "Vertical Smooth Flow" (VSF) principle has been developed. It has also been found to be a good method for copper solvent extraction, decreasing essentially the crud formation and the organic and aqueous entrainments.

Jan 1, 1994

By Kazuhiro Nisizono, Takashi Kuroki, Nobuyuki Mori, Keisaku Ogi

"The improvement of critical current density and mechanical property is essential to the practical application of the superconductive oxides. A solidification technique is developed in this study for the growth of columnar or single Y123 crystal with finely dispersed Y211 and Ag particles through a monotecto-peritectic reaction of Li.(Ba-Cu-Ag-0 rich liquid)+ Y211-+ Y123+Lz(Ag rich liquid). The large solidification rate and temperature gradient can refine the Ag and Y211 particles. But Ag-free region is widely formed along the crystal growth direction in the central part of the Y123 cell. Since this phenomenon occurs because of the cellular growth, it is necessary to narrow Y123 cell width or to grow Y123 crystal with flat freezing interface. By controlling crystal growth direction using a seed crystal, Y123 columnar or single crystal with uniformly dispersed fine Ag particles are obtained. The· behavior of Ag and Y211 particles during the solidification of Y123 crystal is simulated by the peritectic growth model of faceted Y123 crystals.IntroductionY-Ba-Cu-0 superconducting oxide (YBCO) with high critical temperature also has excellent superconducting characteristic under the high magnetic field. The critical current density (Jc) has been enhanced by ·using unidirectional-solidification technique, which can overcome the weak-link problem at grain boundaries and control the crystal orientation and the distribution of Y211 particles which give effective magnetic flux pinning centers in the Yl23 matrix [1-4].In addition to improving superconducting properties, it is necessary to improve mechanical property for the practical application. The silver addition to the melt-textured YBCO superconducting oxide has been reported as the effective method to improve mechanical properties without degrading superconducting properties. Since the material properties are considered to be largely affected by silver particle size, form, dispersion state etc. in the Y123 phase, it is important to control Ag distribution in YBCO/Ag composites. Besides, it is also reported that the silver addition improve the corrosion resistance to the water and CO2 [5,6]. Nishizono et al. [7-9] have reported that the silver distribution in the YBCO/Ag composites is largely affected by the solidification condition, but yet some unclear points are also remained. YBCO has been also fabricated by the zone melting method [10-12], and Furuya et al. [5] and Hirano et al. [13] have reported the fabrication of silver added YBCO composites, but the distribution and behavior of Ag are not investigated in detail"

Jan 1, 2000

By Olusegun J. Ilegbusi

"A two-fluid model is used to calculate flow and heat transfer characteristics of a plasma jet. This model accounts for both gradient-diffusion mixing and unmixing that may result from pressure-gradient-body-force imbalance in the system. The unmixedness is considered to be essentially a Rayleigh-Taylor kind instability. Separate transport equations are solved for the plasma and ambient gas velocities, temperatures and volume fractions. The two fluids allowed to exchange mass, momentum and energy through empirical interaction parameters. The empirical coefficients are first established by comparison of predictions with available experimental data for shear flows. The model is then applied to an Argon plasma jet ejecting into stagnant air. The predicted results show the significant build-up of unmixed air within the plasma gas, even relatively far downstream of the plasma torch. By adjusting the inlet condition, the model adequately reproduces the available experimental data on the temperature profile.IntroductionPlasma jets have important applications in materials processing, some of which include spray deposition, melting and refining, heat treatment and materials synthesis. In a typical reactor, the hot plasma stream entrains a surrounding gas and the resulting heat and mass transfer and the condition of operation of the torch, determines to a large extent, the performance of the unit. The entrainment may prevent uniform mixing and produce regions of unmixed hot/cold gases and non-uniform deposits as a result of insufficient melting of deposit in cold regions. This phenomenon may also affect chemical reaction rate in plasma systems for NOx reduction in exhaust gases.The study of plasma phenomena is often conveniently divided into three parts namely, the plasma torch, the plasma jet and analysis of the particles carried in the jet. The present work concerns processes occuring in the near-field of the plasma jet i.e. just downstream of the torch."

Jan 1, 1994

By A. V. Tarasov

The proposed process is based on creating a controlled frothed layer of molten slag, in which fine particles of carbonaceous reductant and raw material to be processed are mixed with emulsified iron. Frothing of the slag layer without external blowing occurs as a result of intensive evolution of gaseous reduction products. The froth reaction process is maintained due to the heat of an electric arc in the slag layer. When the metal bath is heated by the arc to 1400- 1 500°C, the low temperature of the slag surface of about 1200-1 300°C is maintained due to low thermal conductivity of slag froth preventing heat loss. In order to maintain the required slag froth level and control the process temperature, air tuyeres are installed above the slag bath; blowing air serves also for oxidation of zinc in fumes and for its transportation. High adsorption and thermal insulating properties of slag froth ensure virtually complete elimination of dust and mist entrainment along with low heat losses. The main macrokinetic regularities of the carbon thermal reduction of zinc-containing slag melts have been studied under frothing conditions. The mechanism of formation of gas-slag emulsion has been identified under the conditions of reaction [C]+[O]=CO occurring locally at the slag-metal interface. It has been demonstrated that under the froth reduction conditions the zinc removal rate from the melt increases on the average by 3 to 5 times. Based on the physical and chemical data obtained, basic principles of the dezincing technology have been developed for different intermediate oxide iron-containing products produced in the process of ferrous and non-ferrous metals production.

Jan 1, 2002

By J. Rajek

The novel multi-component, multi-particle, multi-phase precipitation model developed recently is used to predict the precipitation kinetics in complex 9-12% Cr steels investigated within the European COST 522 project. These steels are used for tubes, pipes, casings and rotors in USC (ultra super critical) steam power plants for the 21st century. In the computer simulations, the evolution of the precipitate microstructure is monitored over the entire production heat treatment starting with the casting process, including austenizing, several annealing treatments and in-service conditions. The main interest lies on the concurrent growth and coarsening interaction of different types of precipitates. Keywords: Precipitation kinetics, heat treatment, power plant steels, simulation

Jan 1, 2003

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-Al intermetallic compounds were transformed into Mn-Fe-Si-Al and Mn-Fe-Al compounds by the addition of manganese into molten aluminum. In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnA4 and FeMnAI6 are paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By James B. Pfeiffer

TETRA Technologies, Inc., has applied its HDSIM metals precipitation system to treat a waste stream containing scrubber blowdown and process water from a smelter operation. The combined stream contained cadmium, lead, selenium, arsenic and zinc, plus some iron and copper. Treatment requirements included meeting stringent mass flow limitations for specific heavy metals. The HDS ? system can reduce the arsenic from 600 ppm to less than one ppm. The process generates a dense sludge that can be reprocessed in a smelter, eliminating the liability associated with landfilling. Flow diagrams and process details are discussed.

Jan 1, 1994

By Antti Roine

HSC Chemistry is a widely-used therniochemical tool in the chemical and metallurgical industries and in universities. The main reasons for it's popularity is the easy user interface and the large integrated thermochemical database. This paper summarizes the main properties of the new HSC Chemistry version 3.0, and gives a short review of the new features: Some metallurgical applications with the new features are also presented. HSC Chemistry 3:0 contains seven calculation modules and a thermochemical database with more than 11 ,000 chemical compounds. The new spreadsheet type table editor gives more control to the user, the new graphics routines have fewer limitations and more formatting properties. The capability and speed of calculation routines have also been improved.

Jan 1, 1998

By G. Kugler, M. Tercelj

"The 1.2690 high alloyed tool steel is usually applied for cold working and is alloyed with carbide-forming elements Cr, V, W and Mo. It exhibits very poor hot deformability. Since there is no enough available data in literature for elucidation of this problem, hot workability and development of microstructure during hot deformation was studied. Hot compression tests were carried out in temperature range 850-1150 °C and strain rates range 0.001-6 s-1. SEM and OM were used for observation of microstructure. Results revealed very complex precipitation of carbides that depends on deformation temperature as well as on strain rate. It was found that especially at lower temperatures of hot working range the precipitation of carbides strongly depends on strain rate. Three different hot deformation behaviors’ were observed depending on temperature and strain rate range.IntroductionThe hot workability of highly alloyed high speed steels is usually described as relatively poor in comparison to other steels due to their tendency of cracking during hot working especially when inappropriate hot working conditions are applied. Alloying elements such as Cr, W, Mo and V in ledeburitic tool steels form carbides that improve hardenability, strength, hardness, wear resistance, etc., but they decrease hot workability and narrow hot working temperature range in comparison to conventional steels. The size, distribution, type and fraction of carbides, as well as the thermomechanical history of material and hot working parameters have major influence on the hot workability. The microstructure of ledeburitic tool steels during hot deformation can be characterized as a two-phase system consisting of an austenite matrix and a combination of ledeburitic carbides [1-4]. In the soft-annealed condition the total volume fraction of carbides is in the range 19-30% and in the quenched condition in the range 9-25%, depending on the chemical composition. During heating before deformation a large quantity of carbides dissolve, but non-dissolved carbides can have an extremely diverse influence on the hot workability due to variations in their composition, size, distribution, hardness and shape, and their different behavior during the deformation phase [5-7]."

Jan 1, 2011