Search Documents

By Ephraim Jeya Kumari

The demand for the titanium dioxide pigments and the shortage of higher-grade titaniferous ores with low radioactivity and zircon sands worldwide has encouraged the development of new techniques for the beneficiation of lesser grade titaniferous ores. The inferior quality ores are invariably richer in radio-active and lanthanide oxides, which severely interfere with the fluidized bed chlorination reaction (FBCR), in which ultra-high purity titanium tetrachloride is distilled off for pigment manufacture. However the present beneficiation techniques require high quality ilmenite ores and are not suitable for upgrading lower grade ilmenite ores which do posses trace metals in the form of lanthanides and actinides as Al-phosphates and zirconium silicates, respectively. The presence of mineral hosts, zircon sand and monazite in ilmenite and anatase also increase in chlorine gas consumption in the FBCR and contribute to a larger volume of hazardous waste production, which must be neutralised at a significant cost before being disposed off safely. In view of the problems described for lanthanide (Ce, Nd etc) and actinide (Th, U) trace impurities in titaniferous ores, an alternative route, which is flexible and more accommodating for processing difficult ores, is discussed. In the new process, which may be used for richer grades of ores too, the ore is roasted in air with sodium carbonate below 950°C to promote the formation of water-soluble sodium ferrite and insoluble sodium titanate phases. In this investigation, the high-temperature roasting process and the ensuing hydrometallurgical leaching steps have been analysed in the context of selective separation of lanthanide and actinide minerals from the main titaniferous mineral structures. Evidences for the selective separation are presented based on the chemical (XRD, XRF, AA) and microstructural analysis (SEM, EDX, EPMA) of roasted mass and the leached product. The efficiency of selective separation is also reported based on the chemicals analysis and the particle size of the materials derived after leaching. The paper highlights the various thermodynamic aspects of reaction equilibrium in the Fe-Ti-O-Na system, and the effect of Eh-pH diagram in the determination of pH required for the better control of the removal of iron and sodium. Two different types of Ti ores, namely ilmenite and anatase, their crystal structure and the phase transformation will also be explained on the basis of wet chemical analysis, XRF, XRD, EPMA and SEM-EDX studies. The method developed examines the technological feasibility of the selective separation process.

Jan 1, 2006

By M. S. Moats

The treatment of oxidized residues of zinc with high iron content continues to present a technical challenge in both the steel and zinc industries. Two main problems are commonly identified and include high treatment costs and environmental concerns about contaminated, iron-bearing residuals. A new approach to this problem is described in which selective separation of the iron and zinc into salable products may be potentially feasible. The waste material is first leached to give a solution having an approximate concentration of 110 g/l Zn, 15 g/1 Fe and 40 g/1 H2SO4 and other impurities such as Pb, Cd, Cu and Sb. A suitable organic, such as D2EHPA, is used to load the majority of the iron. The aqueous phase is then acceptable for zinc electrowinning after standard solution purification. The novel step in the flow sheet is the efficient recovery of the ferric iron from the organic solvent using a solid metal to reduce the iron to the ferrous state. The Fe+2 is easily stripped into an aqueous phase in a relatively pure form, suitable for use in water treatment. Process parameters and possible flow sheet designs are described and discussed.

Jan 1, 1995

By In-Ho Chi

In copper metallization, resistivity of copper seed layer is very important since the thickness of seed layer is less than 200iun. Conventionally MOCVD has been used for this purpose however electroless copper plating is simple process and the resistivity of copper deposit is less than that of copper prepared by MOCVD. In this study eIectroless depositions of copper were conducted on different substrate to find optimum conditions of electroless copper plating for electronic applications. To find optimum conditions, the effects and selectivity of activation method on several substrates were investigated. The effects of copper bath composition on morphology were investigated. The effects of pH and stabilizer on deposition rate was investigated. The resistivity of copper with thickness was also measured.

Jan 1, 2001

By Munyaradzi Kwatara, Ron Schonewille, Edgar Peek, Juzer Tayabally

"The potential recovery of nickel from a South-American saprolitic laterite ore using the segregation roasting technique was investigated. The ore was heated to temperatures that ranged between 900 and 1 000°C in a rotary kiln. In all the tests, the laterite ore was first mixed with a predetermined amount of calcium chloride and either coal or coke. By varying the temperature, calcium chloride and reductant in the different tests, a preliminary set of optimal conditions was established for the specific laterite ore that was tested. A combination of chemical analysis and electron-probe-micro-analysis (EPMA) were used to determine and evaluate the effectiveness of segregation roasting on the recovery of nickel. The present paper describes the test procedure and the results that were obtained.IntroductionIt is known that laterite ore resources account for an estimated 72% of the world's nickel resources, with sulfide sources accounting for the remaining 28%. Yet sulfide resources account for 58% of the world's primary nickel production while laterite resources account for the remaining 42% [I]. There are numerous reasons for this discrepancy, but the most important one is the mineralogical and compositional complexity that is associated with laterite ore deposits. For example, this complexity currently offers only limited opportunities for upgrading, thereby creating capital intensive whole ore processing facilities. It then follows logically that the identification and application of a low-cost processing option for the treatment of laterites could potentially open up an opportunity for exploiting these vast untapped laterite resources.To this end, a preliminary screening investigation was initiated by Xstrata Process Support to evaluate the potential application of the so-called (nickel) segregation process as a unit operation that could potentially be integrated into a laterite processing flow sheet. Laboratory bench tests were performed on this segregation process and this paper details some of the findings from this preliminary investigation."

Jan 1, 2011

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderurgica Belgo Mineira, Joao Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

By Xin Wang, Hongmin Zhu, Shuqiang Jiao

"The behavior of electrochemically depositing silicon in a molten high-melting-point fluoride electrolyte was studied at 1300 °C. The cathodic product was characterized by XRD, SEM and EDS. Though the analysis of structure and composition of deposition, it could certify that silicon deposited on the Mo rod and alloyed with molybdenum. A series of tests had been performed on the cathodic behavior of Si4+ ions in BaF 2-CaF 2-Na2S iF 6 molten salt. The influence of electrochemical parameters on the cathodic deposition of silicon was also investigated. The electrochemical behavior of Si4+ ions in applied fluoride melts was observed to proceed according to one-step reaction.IntroductionGreenhouse warming has been a serious global issue. lt is increasingly urgent for clean and renewable energy. Effective utilization of clean and inexhaustible solar energy has become very important. Solar cell (especially poly-Si solar cell) production has significantly increased this decade, as there is a growing demand for clean energy. Since the early 1980s, the annual growth of the photovoltaic (PY) solar cell industry is more than 30%. More than 90% of the annual solar cell production is based on crystalline silicon wafers. This rapid growth leads to a shortage of silicon of the adequate quality and price for the continued growth of this industry [I , 2J. The most conunonly used technology to produce silicon is the so-called Siemens process. This technology, involves the forming of gaseous Si compounds such as trichlorosilane (SiHCli) or silane (SiH4) with subsequent thermal decomposition of these back to Si. This technology is associated with transformations from solid to gas, and then back to solid phase, which lead to high irreversible thermodynamic losses and subsequent high energy consumption, the energy cost being around 200kWh/kg Si [3l_ The purity of the material from this process is very high (9 to 11 N). In general, what is needed for solar cell purposes are reported to require 4 to 6 N quality. To promote continued growth of the silicon-based PY industry, there is need for a low-energy silicon production process which can produce large amounts of silicon with an acceptable quality and a lower price particularly."

Jan 1, 2012

By Gregor Kücher

Lack of basic knowledge on the semi-direct recycling methods for hard metals hinders the application on an industrial scale. However, advantages like reduced expenses and lower environmental impact draw interest at future potentials. Consequently, this report aims to offer insight into the influence of varying bulky hard metal substrates during their lixiviation in acidic media with an oxidant. The statistical software Modde 11 assisted in the development of a design of experiments (DOE) for evaluation of the impact of average grain size, binder and tantalum carbide (TaC) content on the leaching characteristics. The other experimental parameters were constant. Among them were temperature, solution concentration and quantity, duration and substrate surface exposed to liquid volume. Eventually, prediction plots and factors of the computed model equation describe the effects of varying substrate qualities on leached binder metal and selectivity.

By Henry Hu

In high pressure die casting processes, proper control of temperature die yields a high casting production rate and superior quality components, Die temperature is usually influenced by various die design and process parameters such as size and location of intemal water cooling lines, flow rates of cooling lines, and pouring temperature of molten metal. Among them, the cooling water flow rate plays a major role in controlling thermal pattern of the die_ In order to develop an effective control strategy, data of local die temperature must be collected and analyzed, In this study, a PC-based data acquisition and control system (DACS) for die temperature control has been designed, and established, The developed DACS has three input channels for temperature signals and one input channel for water flow rate signals, as well as one output channel for a water pump, and is capable of displaying data in both curve format and value format. Implementation of the DACS in a laboratory setup has also been attempted, It should be pointed out that more advanced control mechanisms can be potentially integrated into this system in future,

Jan 1, 2003

By A. Haxhiaj, Mitovica, E. Haxhiaj

"The paper discusses problems encountered during the release and possibility of using the thermal gas quantity Mathematical models are used to calculate the positive thermal effects of the gases and losses of thermal quantity with gases in the melting process of electric furnaces. The paper discusses in details the percentages of CO, CO2, H2S, O2 and the humidity in gases and their impact on the technological process in electrical furnaces in Drenas. The paper also confers the quantity and temperature of gases, the transfer of thermal quantity and dust with gases in the environment. The paper presents the percentage of humidity in the load which is added in electric furnace for melting and its impact on thermal and environmental balance in the technological process of melting in electric furnaces. Key words: Furnace, load, temperature, humidity, gases.IntroductionNickel easily reacts with gases in the atmosphere of the furnace in which the nickel ore is processed. Such reactions can explain challenges in producing high quality nickel. Reductive atmosphere with the surrounding gases composed of sulphurous anhydrite has harmful effects on the production of nickel. This is mainly due to solubility of hydrogen as well as nickel oxide in the melted metal. Nickel reacts with carbon monoxide and forms carbide of nickel and nickel oxide which dissolve in the melted metal. Carbon monoxide also dissolves in the melted metal. The presence of carbon dioxide and water vapor in the atmosphere of the furnace impact the decrease of acidity in reductive atmosphere of the furnace. The carbon dioxide reacts with nickel and forms nickel oxide and carbon monoxide. Water vapor reacts with nickel and forms hydrogen and nickel oxide that have negative impact on the structure of nickel and its alloys. In this paper the analytical and experimental analyses are proposed that lead to minimization of the negative effects of gasses and humidity in the melting process. As the practical example, the electrical furnace in Drenas is analyzed.1. The Load and Its CompositionThe basic function of the rotational furnace is drying and reductive roasting of the ore which directly is loaded into the electrical furnace for melting. It is important to mention that the degree of roasting and pre-reduction of iron-nickel oxides is reached if the roasting process of the load in the rotational furnace is done at the temperature of 900°C to 1000°C, with the reductive atmosphere in the furnace and with minimal amount of oxygen in the processing gas. The optimal process of roasting and pre-reduction of the load in its mass is around 13 wt%. With the removal of the humidity and the sterile pare of the ore, with the positive impacts in utilization of the thermal and electrical energy in the melting process in electrical furnaces."

Jan 1, 2013

By Klas G. Hultbom

Mercury is present as trace contaminant in many raw materials for metallurgical plants. When such materials are treated with pyrometallurgical processes the mercury is volatilised. Mercury has a high vapour pressure, even at low temperatures, and therefore it is removed only partly by normal gas cleaning processes. The Boliden Norzink scrubbing process removes elemental mercury by converting it to calomel. It is widely used in the base metals industry. This paper gives examples of the application, and also outlines the background for the development of the process. Another technology developed by Boliden for mercury removal is the Selenium filter. This is a fixed bed filter based on the reaction between elemental gaseous mercury and selenium, by which mercury selenide, HgSe, is formed. The mercury selenide is a highly stable compound with extremely low solubility in water and very low vapour pressure. Mercury is removed selectively without any side reactions. Special applications for the selenium filter technology include mercury removal from gases containing sulphur dioxide and geothermal off-gases.

Jan 1, 2003

By Xianzhong Hu, Qingbo Yu, Qin Qin

"Oxy-fuel combustion is one promising option among different CO2 capture technologies. The object of this work is to show the effect of CO2 dilution on the laminar flame speed, flame structure and reaction pathway for methane oxidation at O2/CO2 atmosphere. In this paper, kinetic simulations were made using CHEMKIN with GRI-Mech 3.0 mechanism, which was validated by experimental data of laminar flame speeds. The reaction pathway of CH4/O2/CO2 mixture was derived from reaction flow analysis. Results showed that CO2 decreased the flame speeds, lowed concentration of major intermediates and increased flame thickness. The major chemical pathways of CH4 to CO2 have not changed at O2/CO2 atmosphere comparing with O2/N2 atmosphere, but contributions to major intermediates formation from each related elementary reaction have changed a lot. In addition, the secondary chemical pathways of CH3 oxidation became different at O2/CO2 atmosphere.IntroductionNowadays, as the global economy is developing fast and the pollutant levels (especially global warming gases) are increasing, a lot of researches are focusing on new technologies which can cut greenhouse gas emissions [1]. New technologies have been developed, such as high Mild combustion, flameless combustion and Integrated Gasification Combined Cycle (IGCC) technology. Oxy-fuel combustion using carbon dioxide as dilution of oxygen is considered as a promising approach for reducing CO2 emission. The properties of CO2 in flue gas are different from N2 in air. On one side, the transport, thermal and radiative properties of CO2 are different from N2 in air. On the other side, CO2 is not inert but directly participates in chemical reactions and recent researches [2-5] also present the chemical effects of CO2 on oxy-combustion. For these differences above, the characteristics of oxy-combustion are not alike with traditional combustion. It is necessary to develop the investigation of oxy-combustion.In all combustion processes, laminar flame speed is an important parameter, which links to combustion behavior. Analysis of this parameter can provide a better understanding of the effect of CO2 dilution in the process of oxy-combustion. Several investigations of laminar flame speeds of oxy-fuel flame have been improved, including experimental measurements and numerical computations. A.A.Konnov et al. measured the flame speeds of oxy-methane and oxy-ethane mixture using the heat flux method with a flat burner [6-8]. V. Ratna Kishore et al. used heat flux method to measure the adiabatic laminar flame speeds of hydrogen [9] and H2/CO mixture [10]. Adiabatic laminar flame speeds of hydrogen in O2/CO2 atmosphere are much smaller than in O2/N2 or in O2/Ar. The burning velocity of H2/CO mixture decreased with increase in CO2 content in mixture. Jeongseog Oh et al. [11] used Bunsen flame to measure the laminar flame speeds of premixed oxy-methane mixture with angle methods in atmospheric condition (300k, 1atm). The results were SL=29.1cm/s and SL=29.5cm/s respectively derived from oxy-methane from CH* images and Schlieren photos."

Jan 1, 2014

By Toru H. Okabe

As part of a systematic study on the thermodynamic properties of complex nitrides, phase equilibria of the system Li-M-N (M Mg, AI, Ga) at 900 K were investigated. An attempt to determine the thermodynamic properties of complex nitrides was made by using the galvanic cell method, which utilizes LiMgN as an electrolyte under nitrogen atmosphere. The electromotive force (Emf) of ilie cell at temperatures between 800 and 1100 K was measured. Whilc the Emf of the cell at 900 K was measured to be 0.137 V, data discrepancies of ±0.03V were found. It was difficult to determine temperature dependence of ilie Emf. The Gibbs energy change for the reaction, 113 LbN (s) + 1/3 Mg3N2 (s) = LiMgN (s), at 900 K was determined to be tJ.Gor (LiMgN) -13.2 (±2.9) kJ/mol. Using thermodynamic information on ilie binary nitride from literature, the standard Gibbs energy of LiMgN was derived to be AGO f (LiMgN)= - 121 kJ at 900 K. The thermodynamic stability range of nitride was discussed by constructing isothermal chemical potential diagrams that provide a better understanding of ilie stability region of the LiMgN phase. The diagram was found to be in good agreement with the isoiliermal phase diagram determined by ilie alloy equilibration meiliod. Although the obtained data includes large uncertainties, the results provide a better understanding of the iliermodynamic stability of nitrides. The potential application of this complex nitride to nitrogen chemical sensors or a medium for controlling nitrogen potential is also shown.

Jan 1, 2003

By Nozomu Uchida, Uematsu Keizo, Daisuke Shouji

"Grain orientated microstructure was developed for the improvement of ceramic characteristics. Novel polarized light microscopy was developed to examine the grain orientation quantitatively. The degree of grain orientation was estimated from the retardation determined with a Berek compensator. The method was essential to determine a minor grain orientation, which could not be analyzed by means of conventional X-ray measurements. The data were favorably related to ceramics characteristics. The comparis of the ceramics with various degree of orientation was very important to explain the change of ceramic characteristics with processing.IntroductionMicrostructure with grain orientation has a high potential for greatly improving characteristics of ceramic. However, there has been strong restriction on processing and material for developing this structure. It has been crucial to apply forming methods involving high shear such as injection molding1). Grains must have an elongated shape.In recent years, much attention has been paid on the effect of high magnetic field on diamagnetic materials2)3)4), Many ceramic materials are known to be diamagnetic. High magnetic field has a high potential to orient grains. The principal driving force for grain orientation is the magnetic anisotropy of material, which is generated by non-cubic crystal symmetr5). This method of grain orientation is not restricted by grain shape, and can be applied to all materials having non-cubic crystal structure.This study uses alumina as raw materials, and produces alumina ceramics with orientated grain in high magnetic field (10T). Alumina has a magnetic anisotropy due to hexagonal crystal structure. The degree of grain orientation in the green and sintered bodies will be examined and their relevance to magnetic field will be discussed."

Jan 1, 2000

By Wang Haibei

China is the important country in terms of Ga, Ge reserves and products. These elements usually associate with lead and zinc ores such as in Fankou, Dachang and Lanping mines. Until now these metals could not be extracted from zinc residues effectively. The main reason is that it is difficult to separate zinc and iron. BGRIMM has carried out considerable research on this subject and some hydrometallurgical processes were developed. Zinc residues were pressure leached with a reducing agent such as zinc concentrates or SO2 at 110~130C. The final concentrate of H2SO4 was 30~50g/L. The metals such as Zn, Fe, Ga and Ge were dissolved into solution. In the leaching residue Pb and Ag could reach 20% and 2000g/t. The feed of solvent extraction was prepared from the leaching solution by pre-neutralization ? precipitation of Ga, Ge and acid dissolving. Then Ga and Ge were extracted by solvent extraction through P204 and G315 produced by BGRIMM. After stripping, metallic Ga was produced by electrowinning. GeO2 was produced by precipitation. The iron in raffinate was removed by the hematite process. The solution after removal of iron came back at the zinc neutral leaching stage. In 2003-2004, pilot tests were finished in BGRIMM in cooperation with Fankou Lead and Zinc Mine Ltd. And the extraction rate of Ga and Ge in the leaching stage was 94% and 83% respectively. The total recovery rate was 90% and 80%. It is estimated that the technology has a wide commercial use in the coming five years.

Jan 1, 2006

By Carlos A. Nogueira

Spent Ni-Cd batteries contain in the electrode materials heavy metals like Ni, Cd and Co, which must be recycled due to environmental problems. Pyrometallurgy is normally used for recycling these end-of-life products, but alternative processes by hydrometallurgy, integrating also physical operations, can be used. Hydrometallurgy seems to be useful, because metals can be efficiently recuperated in chemical forms with commercial value. The economical viability of this recycling process can be improved increasing the treatment capacity, through the application to different types of residues with similar characteristics like Ni-MH and domestic batteries, or other residues containing Ni/Co, like sludges, dusts or spent catalysts. Spent Ni-Cd batteries were first physically processed using shredding and wet sieving operations. Best results were achieved using an output of 6 mm in the shredder and 1.4-2 mm in the physical separation by wet sieving, resulting a fine fraction containing 70% of the initial electrode material and only 6% of the initial scrap. The acid leaching of the obtained material in the previous operation was studied, being the parameters like: temperature, H2SO4 concentration and the liquid/solid ratio (L/S) optimized. The values attributed to the factors which concerned the best results obtained on the leaching process were mainly influenced by Ni recovery. In opposition, Co and Cd were easily leached in a wide range of conditions. To attain an overall recovery, with minimum costs, of the three metals, the values of T~100ºC, [H2SO4]=2.3-2.7 M and L/S=8-10 L/kg were considered the most appropriate.

Jan 1, 2006

By Annette Revet

Aluminum fluxes have been used for the remelting of secondary aluminum since the beginning of the recycling industry. During the last sixty years, a number of fluxes have been designed, researched and tested at the laboratory and plant scale. Fluxes are primarily a mixture of potassium chloride and sodium chloride with the addition of some other chloride and fluoride containing salts. The conventional Mining methods of potassium chloride and sodium chloride yield products that are not high in purity without costly reprocessing or additional refining. In 1993, Kalium Chemicals, Ltd. began supplying flux mixtures to the aluminum industry. Kalium produces potassium chloride and sodium chloride which are mined and refined by a patented solution-mining process. The salts produced by this process are high in purity with lower concentrations of iron oxide, sulfates, and other impurities. This paper will present the different mining methods used in the production of sodium chloride and potassium chloride. The paper Will address how these mining methods affect the purity of the final product as well as the effect of purity on the performance of the fluxing salt.

Jan 1, 1995

By Bingyi Bai, Wangjun Peng, Yanling Guo, Jieyu Zhang, Guoding Gao

The phase transformation of bayan obo ore with high concentration of iron and calcium was reduced at temperatures no more than 1000℃ were investigated in this study. The samples with insufficient carbon were treated at the temperature using a vertical furnace with a thermogravimetry (TG). The mineral phases and content were examined using Xray diffraction (XRD) and X-ray fluorescence spectroscopy (XRF) respectively. The complex phases of bayan obo ore transformed to some simple phases after treated with different content of carbon at the same temperature for 10 hours. The result of XRD、 XRF and TG showed that the reduction degree of Fe3O4 phase formation varied with the temperature and the carbon content of bayan obo ore.

Jan 1, 2015

By Malti Goel

"Technology advancements in fossil fuel based energy generation and consumption are currently being aimed at minimization of CO2 emissions. To attain energy security, India must accelerate the pace of economic development, while achieving reduction in CO2 emissions per unit of energy consumed. It would need access to advanced coal utilization technologies to be demonstrated on indigenous coal characteristics. Of specific importance would be: improvement in coal quality, increasing energy efficiency and suitability of other CO2 sequestration technologies for reducing CO2 footprints. There is need to address related risks and financial burden through adoption of policies and regulations including the issue of open access in energy research. In this paper, seven important areas of strategic plan that need to be pursued for managing CO2 emissions in steel energy sector in India are discussed.IntroductionWorld is facing a crisis of climate change, which follows in the footsteps of global energy and environment crises. Accumulation of carbon dioxide from the generation and utilization of energy is leading to greenhouse warming and climate change. The global warming is causing the boundary between four seasons to be fuzzy and resulting in more spiky weather. Significance of its impact on environment is also determining the technology development needs in various sectors of economy for taking remedial measures.To respond to climate change concerns, the steel industry is undergoing a transition. It is at the threshold of a rapid change in technology as it targets innovation to achieve 50% reduction of CO2 emissions per ton of steel produced. Fossil fuel use is the main contributor of increasing concentration of carbon dioxide in the atmosphere. The control of air pollution and CO2 capture are thus relevant for a coal based industry, whether thermal power plant or a demand side energy intensive industry. World steel production has shown phenomenal increase in first eight years of 21st century increasing from 780 Mt in 2000 to 1343 Mt in 2008 [1]. It was merely 28 Mt in 1900. The global CO2 emissions from steel industry are also increasing and became 2550 Mt (3-4% of total GHG). Indian industry contribution was 161 Mt (15% of direct emissions from industry). It is likely to grow further to keep pace with the accelerated economic growth of 8-9% per annum."

Jan 1, 2010

By Liangying Wen, Xuewei Lv, Yuelin Qin, Feng Zhu, Guibao Qiu, Chenguang Bai, Meilong Hu, Shengfu Zhang

"The COREX process is the first reduction ironmaking technology with coal and pure oxygen to get high quality hot metal, which consumes a lot of high quality lump coal and some coke. In order to increase the utilization of fine coal, reduce coke consumption and enhance the competitiveness of the technology, the combustion behavior of pulverized coal injection in melter gasifier is studied experimentally. The results show that the combustion rate of PCI increases with the increase of temperature. And the combustion rate increases with decreasing coal particle size. Compared bituminous coal with anthracite, the former’s burning ratio is higher than the latter in the same granularity. The combustion effect is remarkable when coal blend of bituminous coal and anthracite with the smaller particle size is pulverized in COREX process.IntroductionThe COREX process is the first reduction ironmaking technology with raw coal and pure oxygen to get high quality hot metal, which consumes a lot of high quality lump coal [1-3]. However, the proportion of lump coal in raw coal is very small, and it is avoidless to produce fine coal because of mechanical coal cutter and storage and transportation process, so it is important to resolve utilization of fine coal in COREX ironmaking process in order to energy conservation and reduce the cost of hot metal [4]. Currently, Coal briquetting technology is adopted to utilization of fine coal in COREX process [5], but coal briquetting system has high investment cost and requires feasible adhesive agent. The pulverized coal injection (PCI) into a blast furnace is being used on a global scale to improve the stability and reduce the cost of blast furnace operations [6]. The successful development of PCI in blast furnace is contributed to pulverized coal in COREX melter gasifier. However, it is different in PCI process between COREX melter gasifier and blast furnace, and the differences are as follows: firstly, The air is injected into blast furnace, which temperature is about 1200 ?, but in COREX melter gasifier the normal temperature oxygen is blasted, so PCI in blast furnace begin burning in blowpipe, but the combustion of PCI in COREX melter gasifier is only in raceway. Secondly, the racway of COREX is smaller than that of blast furnace of the same size. So, the combustion behavior of PCI is complex in COREX melter gasifier, which is not use for reference."

Jan 1, 2012

By Zongliang Zhang

Electrowinning is a significant step in metal extraction processes. Because the nature of electrowinning is to reduce metal from its oxidized state, substantial energy consumption accompanies it. Electrowinning processes of different metals have much in common—the deposition of the metal on the cathode and the counter-reaction on the anode. An advanced model was developed that can be applied to a variety of metal electrowinning processes. A model for specific metals can be readily obtained by modifying parameters such as potential, kinetics, and side reactions in the model. The model incorporates mass transfer, gas-liquid flow, electrochemistry, and deposition, making it a comprehensive electrowinning model. The model is applied to copper, nickel, and zinc and verified with the experimental results. In addition, the parameter settings and results of different metals were compared, showing that this model has great versatility and accuracy, thereby making it an efficient and effective research tool.