Search Documents

By Catherine Williams-Beam

Thallium is more toxic to humans than mercury, cadmium, lead, copper or zinc. Its chemical behavior resembles the alkali metals (K, Rb, Cs). It occurs almost exclusively in natural waters the monovalent thallous cation. The solubilities of thallous compounds are relatively high so that monovalent thallium is readily transported through aqueous routes into the environment. The major sources of thallium are the base metal sulfides and precious metal bearing sulfides. Therefore, it is often present as a contaminant constituent in waters emanating from heavy metal sulfide bearing deposits. Thallium can be effectively removed from wastewater to <2 µg/L by reductive precipitation of thallium sulfide. Effective thallium sulfide precipitation requires a controlled solution potential/pH combination. The required potential can be effectively achieved by utilizing a particulate iron slurry or packed column environment. Experimental results will be presented and discussed.

Jan 1, 2003

Bath smelting options for recovering valuable metals from jarositic residues containing 22-28% lead and 16-30% sulphur obtained from pressure leaching zinc-lead-copper bulk concentrates were investigated using thermochemical computations and crucible-scale experiments. Direct fuming of lead and zinc from a slaglmatte bath at 1250-300°C was demonstrated successfully. Up to 93% of the lead was recovered in the fume and steady-state recoveries of zinc were predicted in the range 82-95% under these conditions. The energy required for the fuming reactions was supplied by partial combustion of the fuel, added as char, with air. An important feature of the process is that the recoveries to the fume are not significantly affected by changing: the fuel:air ratio over a wide range. Thermodynamic computations, confirmed by experimental results also showed that the presence of a matte phase is not essential for high recovery of lead and zinc to the fume. Operating conditions which produced a matte ensured that about 70% of the silver and 80-90% of the copper were recovered into that phase. Approximately 98% of the arsenic in the residue was fumed. In the absence of matte the slags contained high arsenic levels (260-330 ppm) but low arsenic (20-60 ppm) levels were achieved when matte was produced.

Jan 1, 1994

By Paul B. Queneau

U.S. plants solely devoted to recovering values from metal-rich wastes have established market niches based on one or more competitive advantages: superior process technology, access to key feedstocks, unique equipment, special knowledge of markets, and an appropriate exit for outfall water. Plant methodology, competitiveness, environmental factors, and economics are examined, with particular attention to feedstocks, technologies, products, and outputs.

Jan 1, 2003

By L. Y. Zhang

The current status of metal hydride alloys for NiMH batteries was systematically reviewed. Extensive application-oriented research and development has successfully made the NiMH battery an important part, with growing potential, among rechargeable batteries. The rare earth based metal hydrides (AB5) have been considered the best alloy material for use in the negative electrode in NiMH batteries. However, being in demand for high performance electronic markets, the still young NiMH industry is facing serious technical challenges in developing better products. Among all the efforts to respond to the challenges, advanced AF3, alloys are in great demand: the capacity enhancement race requires new or improved alloys possessing higher volumetric capacity; price competition mandates MH materials with low cost; high performance under severe service environments calls for alloys with high corrosion resistance when subjected to electrochemical cycling; and finally, high power service requires the negative electrode to deliver current at high rates.

Jan 1, 1997

By George Grandy

Kvaerner experience is being used to develop software to design or simulate crushing and screening plants. The model techniques discussed are presently being used for open-circuit plants and are being extended to closed circuit plants. The program contains a library of routines, each representing a piece of equipment or unit operation, which are assembled into one of several open-circuit plant configurations. Routines include gyratory primary crushers; standard secondary and shorthead tertiary cone crushers; single, double or triple deck screens; and stockpiles, feed bins and belt conveyors. The program uses steady-state models to simulate the performance of crushers and screens that have small residence times and quickly reach equilibrium when operating conditions and/or parameters are changed. The dynamic aspect of the total circuit model concerns the storage units within the circuit, i.e. stockpiles and bins, and, in the closed circuit configuration, circulating loads and size distributions. In many cases, just vendor&apos;s catalog data are necessary for a pre-feasibility simulation; in other cases, actual plant test data are required to obtain more accurate simulations. The entire plant is shown in a single graphic screen so the user can see all the relevant information he might want, and soft-keys are provided for the user to make on- line parameter changes and observe the effects on storage elements, equipment feed rates and the final product size distributions. The model also reports equipment utilization in percentage, power consumption, and other related operating information, and soon, will be able to report estimated capital and operating costs.

Jan 1, 1999

By Abhoy Mukherjee

The Luanshya Smelter is a traditional Reverberatory Smelter which once worked with up to three coal-fired reverbs, and now operates one Reverb and one hot Peirce- Smith Converter, projected to produce approximately 42.000 tons per year of copper anodes. The aim of this study is to select a smelting technology which best fits the upgrading of the Smelter, such that low capital and operating costs are achieved for the projected design production capacity of 60.000 tpy, limited by the available supplies of concentrates. An equally important requisite is the compliance of present and future environmental regulations, which determines the need to install and Acid Plant to treat the smelter primary gases. In the process selection study, the following technologies were analyzed, at a Conceptual Engineering level: the Oxy-fuel Burner Reverb, the Teniente Converter, the CONTOP Cyclone Smelting Reactor, and further, the Ausmelt Furnace, the engineering of which was provided by the proprietary firm. The engineering of the other processes was developed by INDEC, which also integrated the comparative analysis of the four options. The analysis of a comprehensive set of technical factors, including integrated smelter metallurgical models, together with the evaluations of economical features, led to the selection of the CONTOP Smelting Technology for the modernization of the Luanshya Smelter.

Jan 1, 1999

By Rodney T. Jones

Mintek has developed and piloted a novel process for the treatment of nickel-copper and PGM (platinum group metal) sulphide concentrates. The ConRoast process is based on the removal of sulphur by roasting, followed by smelting of the dead-roasted concentrate in a DC arc furnace using an iron-based alloy as a collector for nickel, copper, cobalt, and PGMs. The environmental benefits with respect to sulphur emissions are considerable, in that essentially all of the sulphur is removed from the enclosed roasting equipment in a continuous stream of SO2 of an appropriate strength for feeding to a sulphuric acid plant. This process allows great flexibility with respect to the selection of ore types, and does not impose limits on the minimum quantities of contained base metals or sulphur, and can tolerate very high contents of chromite in the concentrate. The furnace alloy is water-atomized prior to leaching. Iron may be rejected from the alloy hydrometallurgically, by precipitation as hematite for example. The ConRoast process achieves very high metal recoveries, and produces high-purity metals, and a clean high- grade PGM concentrate.

Jan 1, 2002

By Rachel De Lucas

In recent years, as the price of oil soars upward, scientists have started to focus on other energy sources, such as hydrogen. As magnesium can be used for hydrogen storage by forming MgH2, industry will see a growing demand for the hydride. In hydrogen storage and release cycles using magnesium, hydrogen is released from magnesium hydride through hydrolysis and magnesium hydroxide is produced. Therefore, recycling magnesium hydroxide back to magnesium becomes important. The solid oxide membrane (SOM) process is an emerging technology for this process. In the SOM process, MgF2-CaF2-MgO flux is contained in a stainless steel crucible, which works as the cathode. An ionic-conducting YSZ membrane, connected to a liquid metal anode, is partially immersed in the flux. During electrolysis, when the voltage between anode and cathode is higher than the dissociation potential of magnesium oxide, magnesium ions move toward the cathode and are reduced into magnesium vapor. The oxygen ions move toward the anode, passing through the YSZ membrane. They are then oxidized, forming pure oxygen, CO/CO2 or steam (by reaction with hydrogen). The magnesium vapor, generated at the cathode, is collected in the condenser as high purity magnesium. SOM experiments have been conducted with different liquid metal anodes and without reductants. The SOM technique is a highly energy efficient process and with by-products being oxygen or steam, it is also an environmentally friendly green process. A 2-D electrostatics mathematical model was developed as an initial step towards optimizing the design for a three-tube scale-up SOM electrolysis cell. Several possible geometries were examined to develop the scale-up model and convergence of the model was achieved.

Jan 1, 2006

By A. V. Tarasov

The nonferrous metals industry has been a sector with one of the highest growth rates during the recent years. The prospects for the Russian metals industry during the period until 2010 are associated first of all with a growing domestic demand for its products. The technological level of the metallurgical operations in Russia is relatively low in comparison with industrially developed countries: the average energy requirement is higher by 20% to 30%; the amount of generated waste in the process of rolled products manufacture is twice as high; the average labor productivity is lower by 2.5 to 3.0 times; the overall negative environmental impact is twice as high. Improvement of the technological level of the nonferrous metals production under the conditions of market economy is possible by application of innovative technologies for the development of this sector. The main trends for development of the nonferrous metals sector are: - meeting of more stringent requirements to the quality of concentrates; - more complete recovery of associated elements as commercial-grade products; - development of continuous process lines based on autogenous, resource-saving and environmentally safe processes; - use of combined technologies, including pyrometallurgical, hydrometallurgical and upgrading processes; - expansion of the fields of application for nonferrous metals and their alloys.

Jan 1, 2006

The entrainment of copper matte in the slag during the slag skimming stage of a Peirce-Smith converter was studied with a dam break model. Experiments were carried out with a range of fluid pairs where the lighter fluid was allowed to overflow a weir and the amount of entrained heavier fluid measured. The resulting entrainment is measured as the ratio of the heavy to light fluid withdrawn. The fluids include oil-water, water- glycerol and salt solutions-water pairs to cover a wide range of densities and viscosities. It was found that the Richardson number, Ri, correlates the entrainment well. For the case of the liquid-liquid interface initially at the same height as the weir, the entrainment was found to vary with Ri-1/3. The transient flow was simulated with a volume of fluid (VOF) code written in-house and used a stairstep approach to represent flow obstacles. The code was validated against the experimental results with good agreement for the variation of the heights of the two fluid with time. The simulation showed that the prevailing mechanism for entrainment is due to a pressure differential created across the liquid in the converter during pouring resulting in the heavier liquid being rotated upwards and over the weir.

Jan 1, 1999

Laboratory trials were performed in an induction furnace to study droplet formation during lance blowing. Compressed air was blown on a molten iron bath consisting of iron alloyed with carbon and silicon. Steel droplets were collected using a specially designed sampler. The average steel droplet composition and the oxide layer thickness were determined using scanning electron microscopy combined with energy dispersed spectroscopy. In addition, the concentration gradient of elements was determined using a microprobe. It should be noted that a special technique had to be developed in order to prepare the droplet sample. The size distribution and composition of the droplets was also determined using the microprobe. It was found that the carbon content in the droplets was lower than the carbon content in the bulk.

Jan 1, 2006

By Leonard J. Friedman

The contact process for the production of sulfuric acid has been used commercially since before the turn of the century (1880?s), and rapidly replaced the chamber process after the development of vanadium catalysts in the early 1900&apos;s (1910&apos;s - 1920&apos;s). Plant size has increased from a few tons per week to single train units in excess of 4,000 tons per day. Much of the history of the contact process is in the minds of the few remaining early process pioneers that started in the industry in the 1920&apos;s and 1930?s, and in sulfuric acid industry books published in 1921, 1925, 1936, and the last Deucker and West in 1959. Since those not familiar with history are doomed to repeat the failures and mistakes of the past, this paper includes a brief history of the contact process along with the history and development of equipment and materials in each equipment area of the process. The main focus of the paper is to present the development and analysis of equipment and materials in the contact section of the sulfuric acid plant - from the dry tower to stack.

Jan 1, 1999

By Roberto Parada

In a long term program for the optimization of the Outokumpu Flash Smelting Furnace at Chagres Smelter many different subprograms are being developed. One of them is the design and application of a sampling method that can allow the direct diagnostic of the quality of the copper concentrates combustion. We present in this paper the evolution of the sampling devices used in a ten months of continuous sampling campaigns and an example for the sulfur elimination and magnetite formation in the flame from 60 cm to 100 cm under the burner. These type of information combined with the appropriate mathematical modeling of the combustion must propose some considerations to correct the classic criteria in the preparation of the charge for the smelting of copper concentrates based only on the mass and energy balance from the chemical and mineralogy composition of the concentrates.

Jan 1, 2006

By Dachun Liu, Wenlong Jiang, Baoqiang Xu, Yongnian Dai, Bin Yang

"In the traditional method for refining of indium, glycerin-KI and glycerin-NH4Cl are used as electrolytes to remove Cd and Tl by electrolytic refining, which produces In with a purity of 99.995%. Large quantities of polluted industrial waste water are the result. It is calculated that the saturated vapor pressure of Cd and Tl are between 1-200 Pa, which is much larger than the vapor pressure of In. Thus, the study of removing Cd and Tl was carried out over the temperature range between 700-950 °C and pressures between 1-15 Pa. After vacuum distillation the contents of Cd and Tl in crude indium could sharply fall below 1 ppm..IntroductionIndium is a is a pale blue and silver white metal, and has high ductility [1-2]. Pure indium is generally used as a raw material to produce semiconductor compounds, fluorescent material and ITO targets [3]. Sublimation, zone melting and electrolytic refining are major methods to produce pure indium from crude indium. Electrolytic refining is the main method to product pure indium at present. High productive efficiency, simplicity of operation and short cycle of production are major advantages. However, glycerin-KI and glycerin-NH4Cl are used to remove Cd and Tl in electrolysis method. Large quantities of polluted industrial waste water are the result[4]."

Jan 1, 2012

By Guo-Sen Zhu

Research on the formation mechanism and control of corner transverse cracks was carried out. The optical microscope and SEM were applied to analyze the characteristics of cracks. It is found that the cracks occur at the relatively lower temperature due to unbending strain and have almost nothing to do with the mold cooling and powder. The keys to prevent corner transverse cracks are to optimize the corner temperature of slab and maintain the good state of casting machine. Increasing casting speed and decreasing the cooling water flux at the corner in the unbending segments, resulting in mild cooling, were applied during investigation to control corner temperature above the upper limit temperature of the No.3 brittle zone of Nb-contained steel tested by Gleeble-1500 system. As a result, corner transverse cracks were minimized, but centerline segregation got worse. And then increasing the cooling water flux at the corner (intensive cooling) was applied to make corner temperature below the lower limit temperature of the No.3 brittle zone. Great diminution of both corner transverse cracks and centerline segregation was achieved finally.

Jan 1, 2006

By Godwin M. Beene

Large scale mining operations started in Zambia in 1913 and rapidly expanded during the post 1930 period with the opening of several mining and processing plants on the present Zambian Copperbelt. As a consequence of poor tailings dumps design methods at the start of the mines, and in view of stringent Government Legislation pertaining to environment in the recent years, Nkana Mine has developed a unique method of dump construction at its current tailings depository, Tailings Dam 15A. This method has enabled the revegetation of the dump retaining walls while construction is still in progress, a situation which was not possible on the older dumps. Cowdung has proved to be a superior fertilizer for providing plant nutrients on the tailings. The new method of dump walls construction and walls rainwater runoff drainage system has almost eliminated tendency of gully formation which is common on older dumps, as rainfall on the Zambian Copperbelt comes in intense thunderstorms. The decanted water from the dump is discharged to the natural environment in a controlled fashion after ensuring that it meets the Zambian Government Statutory requirements.

Jan 1, 1999

By Yu-ichi Kanbe

It becomes more important to control the composition of inclusions with increasing the demand for quality of products in terms of cleanliness. Along with the development of refining technology to make inclusions harmless, a study was made to develop how to predict the quality of final products. At first, observations of a number of defects revealed that the defects were caused by inclusions larger than 100 m in diameter. Therefore it is required to detect relatively large inclusions in steel, whose existence is quite rare, to identify the quality. In order to estimate the maximum size of inclusions in a given sample, the method with statistics of extreme values has been applied for continuously cast (CC) slabs, hot-rolled coils and cold-rolled coils of type 304 stainless steel. For the CC slabs the diameter of inclusions, which were analyzed to be mostly silicate with globular shape, in the specimens was measured. For the coils, the width of inclusions was measured at the unit section perpendicular to rolling direction because it corresponds to the diameter assuming that the width of globular inclusions does not vary with rolled. Then maximum inclusion diameter in a specimen was calculated. As a result, the obtained values in the rolled coils are larger than in the slabs. This may imply that the measurement with the coils gives the values closer to the truth. Besides, the measurement with the coils is even faster than with the slabs due to its simplicity of preparation of the specimens.

Jan 1, 2006

By Joo Hyun Park

A history of the research regarding the spinel in the community of the stainless steels has simply been reviewed, followed by the recent studies for the formation mechanism of the spinel in the ferritic stainless steel melts equilibrated with the highly basic slags and the crystallization behavior of spinel phase in the calcium aluminosilicate melts containing MgO and CaF2 during slow cooling cycles. It has been proposed that the content of aluminum and calcium in the steel melts as well as the basicity and the content of MgO and Al2O3 in the slags are quite important factors affecting the spinel formation in view of the formation mechanism based on the reduction of MgO (or CaO) and Al2O3 in the slags by the aluminum and silicon added to deoxidize the molten steel. The use of magnesia refractory was also recommended. The formation mechanism of spinel from the MgO inclusions readily formed in the steel melts equilibrated with the highly basic slags has newly been proposed on the basis of the ionic exchange reactions at the inclusion/metal interface and the crystal chemistry of oxides. The crystallization behavior of the spinel phase in the calcium aluminosilicate melts was enhanced by the Al2O3 based on the ionic reaction of spinel formation in the oxide melts, while the size of the spinel crystals in the oxide melts decreased by addition of CaF2.

Jan 1, 2006

By S. B. Breyner, A. Ressler, D. Gregurek, A. Spanring

"The changes in process conditions that frequently decrease the service life of refractory products provided incentive for RHI AG to develop high performance bricks, especially for non-ferrous metal applications. Innovative product development was required to determine suitable refractory products for improving lining life. At the Technology Center in Leoben, Austria, practical corrosion testing methods and facilities, including an induction furnace and rotary kiln, enable detailed comparative analysis of brick wear on a pilot scale. In tests that were carried out using a fayalite type slag, the newly developed RADEX VFG magnesia-chromite grade showed very promising results compared to the standard grades. Based on the test results, optimal refractory solutions can be recommended for this challenging industrial application and field trials can be performed directly at the customer's site.IntroductionThe complexity of metallurgical processes in the non-ferrous metal industry, and especially changes to the process conditions in combination with the diversity of metal processing furnaces ''', requires a precise understanding of each individual system for appropriate refractory product selection l2'. In addition, particular importance is focused on the specific refractory consumption being as low as possible.Another important aspect results from the global shortage of resources, which forces companies to invest in recycling processes. In the base metal industry, recycling operations have resulted in significant changes; for example, operating with two slag chemistries and process temperatures will influence the performance of previously suitable linings. The raw material mix for primary smelters has also changed, including higher levels of secondary raw materials in the smelter feed."

Jan 1, 2012

By Chu Bo-Yi

"This paper contains a comparison of creep-feed and shallow-cut grinding on ceramics with both neat oil and water-based grinding fluids. When a water-based grinding fluid was used in creep-feed grinding on ceramics the vertical forces and specific energies increased markedly fast with result that the wheel surface was damaged seriously. Creep-feed grinding on ceramics with neat oil not only produced much lower grinding forces and specific energies but also resulted in the wheel remaining in good condition and minimizing damage to the ground surface. This finding may lead to a deeper understanding of the behaviors of grinding fluids in grinding processes both on ceramics and metal as well.1. IntroductionAs advanced ceramics are obtaining more and more applications in the technical area, some machining processes are needed after the sintering to reach the accuracy and finish required by components. Because of higher hardness and brittle behaviors of modem ceramic many researches have been done in order to improve grinding efficiency and surface quality.In the grinding metals the concept of creep-feed grinding has been developed in industry as a real alternative to the normal method of shallow-cut grinding. In addition to the general economic advantages, dimensional accuracy and surface integrity are invariable improved using the creep-feed grinding technique.In grinding ceramics former studies have done many works on both creep-feed and shallow-cut grinding on ceramics with water-based grinding fluids since the water-based were thought to be better coolants than neat oil in most tests of grinding metals[l]. It was suggested that the specific grinding energies of ceramics are markedly higher in creep-feed grinding. The grinding force increases vary rapidly with time in the creep-feed case. In other words, so-called speed stroke grinding with high workpiece speed is considered more suitable for improving the grinding efficiency [2][3]."

Jan 1, 1998