Search Documents

By Donald L. Stewart, Ken Overfield, Edward M. Williams

"Recent increases in energy cost have lead to a renewed focus on energy efficiency during aluminum melting operations to reduce fuel usage. The goals of a batch melting operation are to melt the charge using the minimum required energy, to melt the metal to the required temperature within the required timeframe, and to avoid generating unwanted contaminants by overheating the charge.The heat transfer efficiency of a conventional hydrocarbon fired aluminum melting furnace varies over the course of the melt cycle, depending on the conditions in the furnace. The purpose of this work was to develop a method of determining the transient heat transfer efficiency throughout the furnace cycle and to take advantage of this knowledge to optimize the melting process through furnace controls and proper production operations. This furnace survey methodology has been developed and used to evaluate a number of furnaces.Description of a Typical Batch Melting Furnace CycleA typical batch melting furnace cycle will consist of three stages:1. Charging – Solid metal charged through an open roof, solid or molten charged through an open door, and/or molten poured through a furnace blister2. Melting – From the time the door or roof is closed and the burners are turned to high fire until the charge is all liquid and has reached a temperature suitable for alloying (typically ~1350 °F / 730 °C)3. Holding – From the end of the melting stage until transfer or casting is completeIn some cases, further charging can take place after the melting cycle has started. This can happen when the entire solid charge will not fit in the furnace in one load, or if additional molten metal is added while the charge is melting. The bulk of the energy used in the melter is consumed during the melting cycle. The thermodynamic minimum energy requirements for melting pure aluminum are:• Energy required to heat pure aluminum from room temperature to the melting point at 1220°F (660°C) is 288 BTU/lb (670 kJ/kg)• Energy required to change state of pure aluminum from solid to liquid (heat of fusion) is 171 BTU/lb (397 kJ/kg)• Energy required to heat molten from melting point at 1220°F (660°C) to 1350°F (730°C) is 36 BTU/lb (83 kJ/kg)• Total energy required to melt a solid charge from room temperature to 1350°F (730°C ) is 495 BTU/lb (1151 kJ/kg)"

Jan 1, 2009

By Nils Eivind Kamfjord, Mari K. Næss, Gabriella M. Tranell

"In oxidative ladle refining (OLR) of silicon, the metal surface is oxidized resulting in the formation of a condensed silica fume (SiO2). In the current work, industrial measurement campaigns were performed aiming to measure the fume generation during OLR. A thorough discussion of the possible mechanisms has been included in order to improve our understanding of the Si(1)-O2(g) system.The measurement campaigns were performed at the Elkem Salten plant in Norway. In addition to fume generation from OLR, the metal temperatures and ladle purge gas amount were recorded. The results of this work suggest that fume generation during OLR results from splashing of the metal and/or oxidation of the metal surface, with oxygen transport to the metal surface being the limiting factor. Other mechanisms of SiO2 formation were investigated, however insignificant.IntroductionOne of the main environmental and economical challenges facing the metallurgical industry is fugitive emissions of both materials and energy. In the production of metallurgical grade silicon (MG-Si), refining of the silicon generally takes place through an oxidative ladle treatment (purging with an air-O2 mixture). In the refining process, exposure of silicon to air results in the formation of condensed silica fumes (SiO2) – one of the main sources of fugitive emissions in silicon production plants. The oxidation of liquid silicon, as opposed to solid silicon, has not been widely studied and described in the literature [1], thus a thorough investigation of the oxidation mechanisms, and factors affecting the oxidation reaction rate are essential in order to deal with the problem. In the current work, the rate of liquid silicon oxidation has been studied through industrial measurements of fume generation from refining adles, where the purge gas rate and composition have been varied. The results from these measurements were discussed in light of existing models describing the liquid silicon oxidation kinetics."

Jan 1, 2011

By Ying Mao, Zhancheng Guo, Long Ma, Huiqing Tang

"A new 2D computational fluid dynamic (CFD) model was developed for the gaseous reduction of iron ore fines in an innovative reactor-multilayer moving-fluidized bed. The solution of the proposed model was performed by integration of FLUENT and PHOENICS. Numerical results of cold state were compared with the experimental data and the agreement between them was good. A hot case-gaseous reduction of iron ore fines using syngas with this reactor was simulated using the present CFD mode. Results indicate that under the given simulation conditions, total pressure drop is 90 Pa less than that under cold state though the gas supply rate is increased about 4m3 under hot state. Gas temperature decreases from 1073 K at the bottom to 500 K at the top, Utilization efficiency of the gas reduction potential is about 27 %. For ore fines reduction, the final reduction fraction could reach 0. 70 and solid temperature 900 K.IntroductionWith the development of coal gasification technology, various coals could be converted to Syngas with air or steam. Therefore gaseous reduction of iron ore fmes becomes an acceptable alternative process for iron making besides blast furnace route[!] and moreover it still has some advantages in processing low grade iron ore fines[2]. Gaseous reduction using fluidized bed technologies is the most competitive in all direct reduction iron-making processes up to now. It has the advantage that ore fines can be directly charged to the process without prior treatment while its disadvantages are particle agglomeration and high gas/solid ratio[3]. To avoid these advantages, a new reactor, multilayer moving-fluidized bed reactor has been developed for carrying out the gaseous reduction. Hydrodynamic behaviors of gas and fines in the reactor were studied and the results were satisfying[4]. However, due to its unique structure of the multilayer moving-fluidized bed and unique gas-solid flow pattern, models of multiphase flow as IPSA, DPM and Eulerian Model could not give a satisfying solution. The current paper is developed a new CFD model and a new solution approach for simulation of the reactive gas-solid flow in the multilayer moving-fluidized bed for its optimization, design improvement and future scale-up."

Jan 1, 2013

By Shiwei Sun, Hongxu Li, Xiangxin Hao, Xie Yang

"Environmental impact assessment of copper metallurgical processes will soon become a compulsory activity in the future. The goal of this work is to analyses the copper metallurgical processes including pyro-metallurgy and hydrometallurgy based on the life cycle assessment method implemented in GaBi software. The evaluation indicators such as global warming potential (GWP), acidification potential (AP), photochemical ozone creation potential (POCP) and human toxic potential (HTP) are taken into account. The results show that the major environmental impact phase in pyro-metallurgy derives from beneficiation because of the largest material and energy consumption. It is also shown that copper hydrometallurgy has significantly lower environmental impact than pyro-metallurgy. Based on the evaluation results, some corresponding optimization methods are recommended to reduce environmental impact.IntroductionCopper is an important metal in modem society due to its wide variety of uses, including electrical wiring, heat exchangers, piping and roof construction and increasingly consumer electronics. Demand for copper has increased dramatically over the past decades, driving production rates almost exponentially. Annual production of copper was estimated to be 20 million tonnes in 2012 with Chinese production at about 6.06 million ton in 2012P1. The production process of copper has environment impacts that often go unnoticed by the producer. Higher production, coupled with declining ore grades, is placing increasing pressure on the natural environment.Sound environmental management helps producers improve their manufacturing technique. LCA is a well-established tool for assessing environmental impact potential and can be readily adapted to map impact potential over time, which can be used to quantify the environment impacts of a product or a process [21. This is achieved by creating an inventory of all the energy and material flows used in the process's life cycle. The results of an LCA can be used to improve the operation of a process so that they have less impact on the environment."

Jan 1, 2014

By M. Zamalloa

Slag foaming is an important phenomenon in many metallurgical processes. It creates large surface areas for multi-phase reactions to take place. In other applications, it protects electrodes and improves the energy efficiency by reducing radiation from hot surfaces. However, it may also be a source of serious disturbances. To control and optimize the use of slag foams, an extensive knowledge of the factors controlling the foam formation and stability is required. Slag foaming experiments were carried out using synthetic FeO-CaO-Si02 slags at temperatures ranging from 1200 to 1350 "C. A data acquisition system was used to continuously measure the foam height, gas flow rate, bubble frequency and temperature. The experimental results show that the gas injection rate has a strong effect on the behaviour of slag foams. At high flow rates and rapid bubbling, unstable foams with short decay times were created. The addition of P20, favours the foam formation and stability by lowering the surface tension of the slag. The average foam life increases with decreasing basicity (CaO/Si02). It is proposed that this is attributed to the increase of the surface viscosity due to surface adsorption of a thin film of silica, retarding the drainage of the liquid films.

Jan 1, 1992

By Marcelo B. Mourão

The reduction of iron ores by solid carbon, when both are agglomerated together in the form of pellets, has important kinetic advantages. Although several studies have been performed on the subject, some points on the controlling mechanisms need clarification. There is a big scatter in the values of the apparent activation energy reported in the literature, and this may be due to factors like heat transfer, flow of gases in the reduction system, pellet size and composition. This work is concerned with the effect of several parameters on the reaction rate. The parameters studied were temperature (in the range 1173 K to 1423 K), carbon type (coke or charcoal), pellet size, gas flow rate, catalyst action of the produced metallic iron and added sodium carbonate. It has been shown that the values of the apparent activation energy can change according to the reduction conditions employed, and hence any modeling effort will have to take account of these parameters. EPD Congress 1994

Jan 1, 1994

By Henrlk Gripenberg

To solve the environmental and financial problems of the traditional Rotary Salt Furnace process, a new salt-free method for aluminum dross and scrap melting, ALUREC, has been developed by AGA and its partners, Hoogovens Aluminium and MAN GHH. AGA and Hoogovens Aluminium developed the main process concept and jointly carried out trials on pilot plant scale. Owing to excellent results" the partners decided to jointly erect a commercial scale test plant. The order for the design and erection of the furnace went to MAN GHH. The three companies designed the test plant and began operation in the spring of 1994. The results have been excellent and the process is expected to be a technical and commercial success.

Jan 1, 1995

By Alex Meystel, Diran Apelian

"In this paper, an outline is given for a theory of intelligent control (IC) of manufacturing processes (MP) based upon what all of them have in common: all MP's can be represented as distributed networks of sequential/parallel elementary ""lumped"" models; all elementary models are organized by definite input-output conditions, and by the set of constraints; all elementary models incorporate not only well defined physical knowledge, but also assumed physical knowledge, expert knowledge, expected knowledge to be obtained during the process from sensors, etc. This creates a hierarchy of elementary controllers coordinated by local coordinators of different levels up to a global coordinator. The latter verifies the adequacy of MP by using a holistic image of the process: depictogram. The structure of knowledge based controller is introduced, and the analytical/linguistic tools of control are presented. The concept entails a number of perspectives which are discussed in the conclusions.1. IntroductionIt is becoming increasingly clear to those of us in Engineering and Technology oriented fields that the so called ""service industries"" do not create wealth. Moreover, it is now accepted that manufacturing is the key to the creation of wealth from a socio-economic point of view. This appreciation of the importance of manufacturing is reflected by the transformations we are seeing in our factories, as well as the changes in both curricula and research activities of our universities. Though we find these changes to be in the right direction, there is yet much more to be done to advance the frontiers of manufacturing and materials processing as we approach the third rnillenium."

Jan 1, 1988

By B. Q. Li, S. P. Song

"Numerical models are developed to represent complex electromagnetic, free surface deformation and fluid flow phenomena in floating zone refining processes with radio frequency inductive heating. The computational methodology is based on the coupled finite/boundary element method for the electromagnetic field distribution and the Galerkin finite element method for magnetically driven fluid flow and free surface profiles of the molten zone. With the models, the complex transport and free surface phenomena in a floating zone system can be studied as a function of various operating conditions including applied current, frequency, inductor position and shape, surface tension, floating zone diameter and height. Results show that the equilibrium shape is sensitive to the height of the molten zone and that the free surface shapes can have a significant effect on the melt flow in the molten zone. Our extensive simulations also suggest that to ensure accurate results, the same mesh should be used, whenever possible, for both the electromagnetic forces and fluid flow calculations.1. IntroductionThe floating zone processes have been widely used in the materials industry to grow ultra-pure rare earth metal or semiconductor single crystals for sensor or electronic applications that have a tough demand on purity. Developed based on the principle of magnetic melting/levitation, the processes possess a main advantage that the molten zone is supported in air by the electromagnetic forces generated by the coil (see Figure 1), and therefore is free from contamination from a container. Consequently, the final products made from the floating zone processes have higher inherent purity than those by other techniques [1-4].Complex physical phenomena occur in the floating zone processing of materials. These include free surface deformation, magnetically-driven melt flow, which may be turbulent or mildly turbulent [5] depending on the applied conditions, and solidification. Thermal stresses also develop in the single crystals, which are affected by the flow and temperature field and which can have direct implications to qualities of single crystals [6]. An understanding of the fundamentals governing these physical phenomena can be of critical value in elucidating the physics that controls the properties of the metal or semiconductor crystals being produced, thereby providing a rational basis for process improvement and quality control."

Jan 1, 1997

By Liping Gu, Gordon A. Irons

"A 1/3 scale ""thin-slice"" model of an electric arc furnace was developed so that gas could be injected to simulate foaming gas evolution. The influence of arc jets, oxygen lancing and bottom bubbling was also simulated. Liquid velocities were measured by a white light particle image velocimetry system. Numerical simulations of some of these effects were made using commercial CFD packages. Comparisons with measured results show that considerable care is required to select the appropriate model and to interpret the computational results.INTRODUCTIONDuring recent years electric arc furnaces (EAF) have captured a significant share of steel production, partially due to increased productivity through the introduction of advanced technology such as oxygen injection, slag foaming and long-arc operation, process automation and post-combustion. However, systematic analysis of the process and these effects on heat transfer and fluid flow in the furnace is still in its infancy. Most investigationsl1 6l have been restricted to a specific application such as oxygen lancing or bottom stirring. In addition, it is very difficult to make comparisons between these computed results and experimental/industrial results. In this work a 1/3-scale ""thin-slice"" model of Dofasco's 190 ton EAF was built. The fluid flow in the bath due to the arc jets, bottom stirring, oxygen lancing and CO evolution was simulated. The velocity distributions in the bath were measured using Particle Image Velocimetry (PIV) System. In addition, numerical simulations of bottom stirring and CO evolution were carried out using two commercial CFD packages (Fluent and Phoenics). The objective of this work is to validate the mathematical models so that they can be applied to the full-scale furnaces."

Jan 1, 1999

By Saskia Duyvesteyn

For many applications in hydrometallurgy and water treatment it would be advantageous to use ion-exchange resins in stirred reactors. However, attrition of the resin may lead to significant losses of both resin and metal values and prevent water quality goals from being reached. We have studied the recovery of fine resin particles by froth flotation, using the model copper - Dow XFS4195 chelating resin system. As the functional group on the resin is a bis-picolylamine, the resin should be amenable to flotation by anionic collectors, such as sodium dodecylsulfate and sodium dodecylsulfonate. The kinetics of copper loading from dilute aqueous solutions in an agitated vessel were studied as a function of copper concentration, pH and resin bead size. The flotation of unloaded resin was investigated for different types of collector, collector concentration, conditioning time, and resin bead size. Potential applications are discussed.

Jan 1, 1995

By P. D. Nolan

Smelters operating under pollution control orders have become increasingly dependent upon the reliable operation of sulphuric acid plants and no factor affects the long term reliability of those plants more than efficient gas cleaning. The sources and characteristics of contaminants in smelter of fgases and the conventional approaches to removing these contaminants to accepted levels are discussed. New technology is described which offers advantages of lower capital cost, lower operating cost and reduced space requirements over the conventional approaches. This new technology has been developed by LAB s.a. and is licensed for metallurgical gas applications by Chemetics International Company.

Jan 1, 1983

By C. J. McKee

A gold-silver-lead-zinc deposit at Montana Tunnels, Jefferson County, Montana is located in a diatreme of middle Eocene age (45 to 50 m.y.). Sulfide minerals within the diatreme occur as disseminations, veinlets, and locally as breccia matrix. Principal sulfide minerals are pyrite, sphalerite, and galena. The diatreme is a matrix-rich quartz latitic breccia with a fine grained rather soft matrix and heterolithic clasts. The ore deposit contains approximately 50 million tons of ore at a grade of 0.025 oz/ton Au, 0.5 oz/ton Ag, 0.25 % Pb, and 0.65 % Zn. Mining is by open pit methods. The original process flowsheet included flotation and cyanide leaching. Problems with the leaching circuit led to a change to the straight flotation process which is presently in use. To maintain a reason-ably uniform feed material, blending of ore is required for grades of four metals as well as for ore hardness and oxidation.

Jan 1, 1988

By Takamasa Ishigaki, Gervais Soucy, Mohamed Rahmane

"The induction plasma jets employed for the in-flight nitridation of molybdenum disilicide (MoSi2) powders were investigated in terms of their flow characteristics. The present study shows the effect of the operating parameters of the plasma torch, as used for this process, on the plasma jet properties. The enthalpy probe techniques, along with mass spectrometry, were employed for the measurement of the jet temperature, velocity and concentration fields. The measured values were compared to the results of a numerical simulation performed on the plasma flowing inside the torch-reactor system. The process operating conditions studied were the plasma plate power, chamber pressure and sheath gas composition. The optimal conditions for effecting the nitridation process using thermal plasma are obtained at moderate plasma plate power, at around atmospheric pressure and by using a mixture of argon and nitrogen as the plasma torch sheath gas.IntroductionMolybdenum disilicide (MoSi2) based composites are considered to be one of the most promising candidates for high temperature structural material applications [!], especially because of their high melting points, good oxidation resistance and relatively low cost. However, the wide application of these composite materials is still limited by some factors such as their brittleness at room temperature and lower strength at high temperature (> 1500 K). To overcome such limitations, a number of researchers [2-4] have earlier studied various kinds of reinforcements for MoSi2, e.g. oxides, silicides and nitrides. More recently, Fan and coworkers [5-9] have demonstrated the possibility of in-flight nitridation and carburization of MoSi2, using a thermal plasma process. This work has confirmed the plasma synthesis route as one of the most promising methods for creating an in-situ second phase structure. Properties of the plasma flow, such as its temperature, flow velocity and composition, are of crucial importance for the nitridation of MoSi2 powders during their flight in the plasma. Therefore, the optimization of such a process involving plasma· generated reactive species necessitates a thorough understanding of the plasma flow characteristics."

Jan 1, 2000

By Milton Manrique, Edgar E. Vidal, Patrick R. Taylor

"Ultrafine zirconium carbide powder has been synthesized using zircon concentrate and methane in a thermal plasma reactor. The effect of several experimental variables, such as power used and zircon particle size, on the conversion has been studied. A thermodynamic analysis of the possible reactions and stable compounds was performed. A mathematical model that describes the in-flight decomposition of zircon particles was developed based on a description of the temperature and velocity profiles calculated in the reactor. It was shown that the formation of zirconium carbide from zircon and methane is thermodynamically possible. Complete 'vaporization of zircon in the reactor is predicted when the particle size is below 45flm and the effective power entering the reactor is 15 kW. The powders were collected and characterized by XRD, SEM, TEM and chemical analysis using ICP. Results of the product analysis indicated the presence of zirconium carbide, zirconium oxide, silicon carbide and silicon oxide.IntroductionIn recent years there has been an increased interest in the production of nanometric sized powders of ceramic materials for use in advanced materials applications. One possible method to produce these powders is with a thermal plasma reactor, which offers high temperatures and fast quenching rates. This technology has been called - Thermal Plasma Synthesis - [1].Zirconium Carbide (ZrCx) has typical properties of transition metal carbides: elevated hardness - between alumina and diamond - a high melting temperature of 3420°C and high chemical stability at room temperature [2]. ZrCx has a Bl crystal structure with deficiencies in the number of carbon atoms in the cell with x between 0.6 and 1 [3]. Different methods have been used to produce ZrC, one method is by direct reaction of zirconium hydride or halide with carbon. Other methods used are direct reduction and carburization of zirconium oxide (Zr02) and reaction of metallic zirconium with a caburizing gas such as acetylene [3]. Recently small films of ZrC have been obtained using a sputtering device [4,5]. ZrC has been used in nuclear plants as a low neutron absorbing and high mechanical resistant refractory material and also as a constituent in cathodes made of UC-ZrC [6]. It is also used in the form of tubes, boats and crucibles to handle molten metals and as part of electronic devices used for thermoionic transducers. Recently ZrC has been used along with zirconium diboride (ZrB2) to produce composite materials [7,8]."

Jan 1, 1996

By O. Ryosuke Suzuki

A new metallurgical process via sulfide is proposed: a sulfide is produced at a high temperature from its metallic oxide using gaseous CS2, and this sulfide is electrochemically reduced to its metallic state using molten salt. This combined process via sulfide is effective to obtain high purity of metallic powder, even if the metal in its oxide is strongly combined with oxygen. For example, it is not easy to reduce stable oxide TiO2, and only Ca can remove oxygen to form α-Ti. However, a fairly large amount of oxygen remains as Ti–O solid solution. Because the solubility of S in Ti is very small, this proposal was examined experimentally both on the conversion of TiO2 to TiS2 and on the successive reduction of TiS2 to Ti. TiO2 powder was exposed to CS2 gas flow at 1073 K, and the conversion to TiS2 was confirmed. TiS2 could be reduced to Ti powder either by calciothermic reduction or electrolysis in a CaCl2 melt. By Ca reduction at 1133 K in CaCl2 melt, sulfur concentration decreased to 0.03 mass%S when the amount greater than twice the stoichiometric calcium amount is added. By electrochemical reduction at 1173 K in CaCl2–CaS melt, S concentration significantly decreased to 0.01 mass% S when four times larger amount of electric charge was supplied.

By Akira Kaneda

Mitsubishi continuous process employs an electric furnace for settling matte from slag. Electrodes are immersed into the slag layer in the slag-cleaning furnace and the temperature of the melt is maintained at a predetermined level by Joule's heat. Electrodes are immersed to the depth where the current of each electrode is kept at a set value, and they are raised or lowered automatically to compensate for the deviation from it. Because electric resistance of the bath is varied with the matte level in the furnace and the composition and temperature of the slag, the immersion depth of the electrodes is affected by them. Therefore by monitoring the immersion depth and its change with time, abnormal situations in the furnace, such a~ rise of matte level or local abnormal state of melt, can be detected. In this paper, relations between state of the furnace and electrode behavior are discussed based on the plant data, and then a new and simple monitoring method of the condition of the furnace is proposed.

Jan 1, 2001

By R. L. Nyirenda

The use of ammoniacal ammonium carbonate (AAC) leaching for the treatment of carbon steelmaking EAF dust has been investigated on a laboratory scale. The experiments have been conducted on dust samples obtained from three European steelmaking companies. As received, the dusts were found to be toxic when tested according to current EPA toxicity testing procedures. Toxicity was on account of the leachability of one or more of the following elements: Ag, Hg, Pb, and Cd. Leaching experiments with concentrated AAC solution at 40 " C showed that zinc oxide present in the three dust samples, 60-80% of the total contained zinc, was rapidly solubilized. Data on the dissolution characteristics of Cd, Fe, Pb, Mg, and Mn are also presented. Toxicity tests conducted on residues of the leaching experiments found these to have leachates below past and current EPA toxicity threshold limits.

Jan 1, 1993

By D. A. Salinas G., A. H. Castillejos E.

Pachuca tanks are commonly used in the hydrometallurgical industry to carry out leaching operations. The fluidynamic characteristics of the liquid phase, resulting from the injection of gas into the draft tube, are important to achieve the complete suspension of the mineral particles and has a decisive influence in the mass transfer processes occurring in this reactor. This study investigated the effect of different design and operating characteristics on the liquid velocity field. using a laboratory-scale Pachuca tank. The transparent model was filled with water, and air was injected through the bottom in the absence of mineral particles. The liquid velocities over the whole reactor were measured under several experimental conditions using particle image velocimetry (PIV). This technique allowed to obtain a very detailed picture of the liquid motion even in the draft tube, as long as bubbles were absent from the measured field of view. The experiments have shown that the liquid velocities increase with increasing the draft tube to tank diameters ratio, the distance from the conical bottom to the draft tube entrance, or the gas superficial velocity. On the other hand, an increase in the water level with respect to the draft tube outlet caused a decrease. A mathematical model, which used the no-slip model, to calculate the variation of axial effective density along the two-phase region, was found to predict liquid velocity fields which agree very satisfactory with the experimental results obtained under all the conditions studied.

Jan 1, 1999

By Roderick 1. L. Guthrie, Mei Li

"A mathematical model was developed to study the role of orifice shape in the detection of inclusions in LiMCA (Liquid Metal .cleanliness Analyzer) system. The fluid flow field within the ESZ was obtained by solving the Navier-Stokes equations. The trajectories of entrained particles were calculated using the equations for motion of particles. A numerical study of the effect of orifice shape on signal shape generated by inclusions passing through orifice showed that the signals in a parabolic orifice are gaussian in shape, while those in a cylindrical orifice are trapezoidal in shape. This signal shape difference needs to be taken into account when performing particle discrimination. Orifice shape influences also pass-through fraction of inclusions. Finally, a study of the orifice shape on critical conditioning currents suggested that as the polynominal coefficient of the parabolic orifice increases, the critical conditioning current, which is also the maximum operating current, decreases dramatically. These critical conditioning currents also increase as the fluid flow velocity within the ESZ increases. IntroductionThe presence of non-metallic inclusions in metals often leads to impaired mechanical properties such as a reduction in fatigue strength, and to processing problems such as tear-offs in deep drawing and increased breakage rates in wire drawing operations. Similarly, inclusions cause a variety of surface defects in rolled or extruded products.Prior to the development of the LiMCA system (1) at McGill University in the early 1980's, it was not possible to measure inclusions, in situ, in liquid metals. Compared with other techniques, such as sedimentation, filtration and metallography, which require considerable amounts of labor and time, the LiMCA method has the advantage of providing not only information on the volume concentration of inclusions, but also on the size distribution of inclusions immediately and quantitatively."

Jan 1, 2001