Search Documents

By G. G. Krishna Murthy

Several experiments were carried out to simulate the bath smelting reactions where iron oxide particles were dropped on to an iron-carbon bath containing molten CaO-SiO2-Al2O3 slag layer on its surface. The composition of the slags used in the experiments was %CaO:46.1; %SiO2:41.7; and %A1203:12.2. Experiments were con¬ducted with carbon saturated iron melts contained in either a pure graphite crucible whose walls were covered with a pure alumina tube, or a pure flat bottom alumina crucible, at 1723-1823 K. Degree of reduction of a pure iron oxide particle was linear with time in the initial stages (up to about 20% oxygen of the original pellet was reduced). The rate of reduction of smaller oxide pellets was smaller than that of a bigger pellet - the time for complete reduction of a 5.6 g wustite pellet was smaller than that for a 1.2 g wustite pellet. It was also established that the interaction rates obtained by adding a molten pure oxide particle of given weight to the system were lower than that determined by using a solid oxide particle of same weight. The overall rates of reduction decreased with decreasing the bath temperature. The experimentally determined rates of reduction based on the time for 70% reduction were influenced substantially by addition of slag up to about 50 g on to a bath of 78.8 mm in diameter, and remained constant when slag present on the bath surface was between 50 g and 200 g.

Jan 1, 1993

By A. A. EI-Geassy

High-grade iron ore fines rejected from the DRI plants (>96%Fe2O3) were isothermally reduced in 30-60%CO/H2 gas mixtures at 973-1273K. The freshly reduced reaction products were then subsequently carburised in either Hz/CO or H2/CO/S mixtures at 823-1 073K for 30-120 min. The thermogarvimetric technique was used to follow up both of reduction and carburisation reactions as a function of time. The carburised samples were characterized by X-ray and Mossbauer techniques. Chemical and carbon analyses were also applied. The influence of temperature and gas composition on the reduction behavior was investigated. The calculated values of apparent activation energy, application of gas-solid mathematical formulations were correlated with the microstructures to predict the reduetion mechanism. The influenee of carburization time, temperature, CO contents in H2/CO or H2/CO/S were investigated. A conversion extent of Fe to Fe3C was taken as a measurable index for the efficiency of carburization rcaction under the different experimental conditions.

Jan 1, 2003

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By John W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct ironmaking pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicates that 69% are less than 2.5 um across, 21 % are 2.5-5 um, and 10% are larger than 5 um. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By N. L. Piret

Reprocessing of low zinc-bearing residuals with a zinc content of less than 10%, originating from the iron and steel industry, has been given more and more attention in the last few years, due to the potential landfill liability and the increasing cost of disposal by dumping. Whereas, recycling of hazardous electric arc furnace dust is already being performed commercially on a large scale in the U.S., Japan and Western Europe, almost no reprocessing takes place in the case of these low grade zinc-bearing materials. In blast furnaces and basic oxygen furnaces dusts and / or sludges are generated at a rate of 1 to 2 % of the respective production. The technologies for the retreatment of these types of materials, either commercially available or still being developed are briefly described hereafter. They involve internal recycling, upgrading by physical separation methods, separate hydrometallurgical processing and pyrometallurgical treatment. Their scope and limitations are critically assessed in terms of technological applicability, economic feasibility and environmental compatibility. Since, the possibtlity of achieving economic profitability is unlikely with this type of material, the main criteria for acceptability of the treatment process are: generation of a iron-rich material, suitable for treatment by the iron/steel industry, acceptance of the non--ferrous metal-bearing sub-product by zinc smelters, generation of non-hazardous waste materials.

Jan 1, 1992

By R. Nilsson

In the present work, an assessment of the sulphide capacities of a number of binary and ternary slag systems have been carried out in the light of a sulphide capacity model. The model is based on the expression: {CS- exp (-A G °/R T) ? ao2 / fs2-} where AGO is the standard Gibbs energy change for the above reaction, ao2 is the activity of oxygen ions and f, is the activity coefficient of the sulphide ion in the slag. In the present model, the ratio (ao2/fs2) is optimized for the experimental data available in literature. The systems assessed are the binaries MnO-SiO2, CaO-SiO2, Al2O3-CaO, as well as the ternaries CaO-Al2O3-SiO2 and CaO-MnO-SiO2. In the case of all these systems, the experimental data available in literature were complemented by measurements carried out at the Division of Theoretical Metallurgy. The sulphide capacities of some FeO- containing binary, ternary and quaternary slags are also examined. The potentiality of the model to estimate the sulphide capacities of complex slag systems from binary and ternary data is demonstrated.

Jan 1, 1996

By Saeid Pournaderi, Ahmet Geveci, Ender Keskinkilic, Yavuz A. Topkaya

There are mainly three commercial nickel laterites in Turkey: Gordes, Caldag and Sivrihisar. The first two appear in Western Anatolia. The third one, Sivrihisar (Yunusemre) laterites have been found in the first decade of the millennium, in the Central Anatolia region of Turkey. Since then, mining facilities have been continued in Yunusemre. Calcination, prereduction and smelting of Sivrihisar laterites have been extensively studied and published. In the current work, some results of the studies related to characterization of Sivrihisar laterites will be presented.

Jan 1, 2016

By Batric Pesic

The interactions of mineral-pyrite with T. ferrooxidans were studied by using a cyclic voltametry technique. The interactions with bacteria were carefully examined during the entire growth stage of bacteria (fermentation). Several very important discoveries were made. For example, the pyrite surface invariably drastically changed its properties at the second day of fermentation. Beyond two days of fermentation, the cyclic voltamograms were insensitive to convective diffusion produced by stirring. The SEM study revealed that bacteria populated the pyrite surface at an extremely high density levels. The high density of bacteria, and the solid reaction products formed on the pyrite surface created conditions for pore diffusion which explained why the CVs became insensitive to convective diffusion in solution (stirring).

Jan 1, 1990

By Zhihua Wang

Through metallurgical calculation and process analysis based on metallurgical theory, it is aimed to raise the concentration of smelting oxygen and improve the update speed of reaction interface, accelerate the reaction and achieve a high-intensity smelting at the stage of converting. The PM plant has launched a theoretical research on model of high-intensity converting aiming at increasing the oxygen concentration of converting, carried out transformation of Kaldo furnace converting system, performed a series of industrial trial operations, conducted multiple rounds of tracking test and data comparison in reducing the furnace cycle, lowering the unit consumption of fuel and stabilizing the furnace lining life. The move has practically tested and verified the correctness of high-intensity smelting theory.

By Yuchun Wang

In principle, supported liquid membranes could be an exceedingly elegant separation process. However they tend to fail by displacement and emulsification of the organic solution in the pores, which allows mixing of the feed and strip solutions. We have stabilized supported liquid membranes comprising moctylamine in nylon and PVDF supports by covering the pores with semi-permeable polyamide films, using an in-situ polymerization technique. Scanning electron microscopy demonstrates that the polyamide films are sensitive to production conditions and the nature of the support. The transport properties of stabilized supported liquid membranes for Cr(VI) are compared with those of unstabilized membranes.

Jan 1, 1998

By N. L. Piret

In copper smelting minimization of solid waste generation is receiving increased attention with more stringent environmental legislation and lower disposal space availability. Copper smelting slags generally being valorizable, solid waste generation is attributed to the presence in the feed of unvalorizable impurities which do not report to the slag and to the unavoidable formation of contaminated dilute acid solutions which need neutralization. As to unvalorizable impurities, solid waste minimization is achieved by rejecting them in the highest possible concentration. Dilute acid is mainly due to the formation of SO3 in the smelter gases and to the discard of decopperized bleed-off electrolyte. Its generation is substantially lowered by preventing SO3 formation, by converting the dilute acid to a valorizable product, e.g., by thermal decomposition for H2S04 recovery or by precipitation as chemical gypsum, and by suitable treatment of the bleed-off electrolyte for impurity removal. Industrial processes are evaluated and alternatives are discussed.

Jan 1, 1994

By Michael L. Sorokin

The behaviour of cobalt during processing of nickel raw material is analysed within the Ni-Co-Fe-S-O-SiO2 system using the computer model. For this purpose the thermodynamic parameters for "three-suffix" Margules's equations in Co-Fe-S and Co-Fe¬Ni-O-S1O2 systems were computed! Phase and iso-activity diagrams for Co-Fe-S system, and phase diagrams for the systems Co-O, Co-Fe-O, Co-Ni-O, C-oO=SiO2 and Co-Fe-O¬SiO2 are calculated using the developed computer programs and identified parameters. The diagrams are used to analyze cobalt behaviour at smelting and converting.

Jan 1, 1995

By Daniel Hoffman, Katerina Aifantis, Ibrahim Miskioglu, Jaroslaw Drelich

"A new method to determine the elastic modulus of a material using the atomic force microscope (AFM) has been proposed by Tang et al. (Nanotechnology 2008, 19, 495713). This method models the cantilever and the sample as two springs in a series. The ratio of the cantilever spring constant (k) to diameter of the tip (2a) is treated in the model as one parameter (a=k/2a). The value of a, along with the cantilever sensitivity, are determined on two reference samples with known mechanical properties and then used to find the elastic modulus of an unknown sample. To determine the reliability and accuracy of this technique it was tested on several polymers. Traditional depth-sensing nanoindentation was preformed for comparison. Using both methods, the elastic modulus of the polymers tested was calculated. The elastic modulus values from the AFM were within ±(5-20)% of the nanoindenter results.IntroductionThe atomic force microscope (AFM) has proven to be a useful tool for characterizing materials on the micro- to nano-scale. The most common use of AFM is to image and measure the topography of the sample surface, but AFM has also been used to characterize the mechanical properties of materials [1-3]. With AFM's ability to scan the sample surface, features of interest can be found and indented. It provides an advantage over traditional nanoindenters that use optical microscopes and thus cannot resolve nano-scale features. This makes AFM a useful tool for characterizing materials on the nano-scale."

Jan 1, 2011

By Huimin Lu, Min Li, Jinghua Zou

"Zeolitic imidazolate frameworks (ZIFs) are new type of porous materials, form inerratic polyhedral in three-dimensional with large cages and small apertures, and appear structural diversity. Their hole size can be adjusted. These materials have high selective adsorption capacity to carbon dioxide. In this paper, zeolitic imidazolate frameworks were synthesized by solvothermal synthesis method with dimethylformamide (DMF) as solvent and structuredirecting agent, divalent metallic ions as cation, and imidazole as ligand. The crystals were characterized with XRD, SEM for their crystal structures and physical properties, the adsorption of the crystals for carbon dioxide was also tested, and the result suggests that these porous materials have a capacity of 1.35ml/g for storing carbon dioxide at 273 Kelvin under ambient pressure.IntroductionGlobal warming caused by the increase of carbon dioxide in the atmosphere has become one of the main environment problems, contemporary research has focused on ways to slow or stop this trend. CO2 capture has attracted attention due to the potential to trap and sequester large amounts of CO2 from concentrated sources such as power plants [1]. Traditional technologies in capturing CO2 include absorption by aqueous amines [2]. However, utilization of this process is energy intensive and expensive. Carbon dioxide storage materials investigated so far can be divided into two categories: chemical storage adsorbents and physical storage media [3]. The first kind of materials can chemically adsorb carbon dioxide within their structures and need thermal energy to release the adsorbed carbon dioxide. The examples of the chemical adsorbents include aqueous amines, gas-hyperbranched aminosilicas [4]. The physical adsorbents store carbon dioxide by physical adsorption of carbon dioxide at elevated pressure and release the adsorbed carbon dioxide at low pressure. The physical adsorbents that have been investigated for carbon dioxide storage include zeolites, carbonaceous materials and other porous materials. Until recently, a new type of microporous material, known as zeolitic imidazolate frameworks (ZIFs), has been reported as promising adsorbents for carbon dioxide storage [5 ~ 10]."

Jan 1, 2010

By J. E. Clemson

The Black Pine sediment-hosted, disseminated gold deposit is located in Cassia County, Idaho. Gold mineralization occurs in flat-lying zones 50 to 100 feet thick. Total geological ore reserves are 5.6 million tons grading 0.049 oz/t. Ore types include: non-carbonaceous, oxidized ore; carbonaceous, sulfide ore; and carbonaceous, partly oxidized ore. In the oxidized ores, native gold grains commonly occur in porous hematite pseudomorphs that have replaced disseminated framboidal and euhedral pyrite, and this gold should be readily leached by cyanide solutions. Approximately 4 % of the native gold observed in the oxidized ores is locked within gangue and may be refractory to cyanide solutions. Native gold has not been observed in the unoxidized samples, all of which are characterized by primary sulfides. It is suspected that the bulk of the gold mineralization in the sulfide ore occurs as submicroscopic particles within pyrite and will be refractory to cyanidation. It is believed that much or all of the gold observed in the oxidized samples was originally in pyrite but was released and re-precipitated during oxidation. The degree of oxidation of the pyrite and the presence/absence of preg-robbing carbonaceous material is used as a guide in delimiting zones of mineralization amenable to heap leaching.

Jan 1, 1988

By J. Szekely, S. Rhee

"A mathematical formulation has been presented to describe heat and fluid flow phenomena in CVD operations. In the statement of the problem, which included consideration of plasma enhanced CVD systems, emphasis was placed on identifying the parameters which play a key role in determining the rate and the spatial uniformity of the deposition process. This was done both through the appropriate dimensionless groups and by presenting an extensive set of computed results. The main conclusions that may be drawn from this work are that the deposition rate will be inherently non-uniform for atmospheric CVD systems; this may be somewhat ameliorated by inclining the susceptor or changing the vessel contours. Operation at greatly redeced pressures and for PECVD systems will give a much more spatially uniform deposition rate.1. INTRODUCTIONIn recent years, there has been a growing interest in chemical vapor deposition techniques for the preparation of thin films for semiconductor, photovoltaic applications and for coatings in general, as evidenced by numerous journal articles and symposium proceedings devoted to this topic (1-6). An interesting variant of this technique is to perform the deposition in a plasma or glow discharge at low pressures because this technology obviates the need for the thermal decomposition of the precursor at the substrate surface and permits operation at greatly reduced temperatures (7-10).By far, the largest portion of the reported work dealing with both these aspects of the technology has been concerned with the characterization of the deposit, quite properly so. However, in more recent times it has been realized that the transport aspects of these processes are also deserving of attention because the understanding of heat flow, fluid flow and diffusional phenomena may provide the key to the solution of problems associated with obtaining uniform deposits and the proper scaling of laboratory measurements in order to design industrial CVD systems."

Jan 1, 1986

By S. M. Hay

The zinc content of blast furnace and basic oxygen furnace dusts is low compared with electric arc furnace dusts and it is generally not economical to treat the dusts to recover zinc. However, they have a high iron content and removal of the zinc would allow recovery of the iron values. A literature review and thermodynamic analysis was undertaken and, as a result, several smelting options were identified. This paper describes experiments undertaken to develop understanding of metallurgical aspects of these processes which are not amenable to theoretical analysis. Dusts from an Australian steelworks were characterised in order to determine their mineralogical make-up and the form of the iron. The processing aspects investigated in the laboratory were slag-metal equilibrium and solid-state pre-reduction using reducing gases of compositions expected from bath-smelting processes. Particular attention. was paid to the deportment of zinc, sodium, potassium, phosphorous and sulfur between the phases formed during smelting and pre-reduction. The smelting results indicate that less than 10% of the zinc, sulphur, sodium and potassium report to the metal. About 99% of the zinc and potassium and about 80% of the sodium could be volatilised from the dusts by reducing them at 1,000°C with mixtures of CO, CO2, H2 and H2O even when metallic iron was not formed. The experiments indicate that smelting of blast furnace and basic oxygen furnace dusts should produce hot-metal of a composition which can be blended into the main stream of hot-metal in the steelworks.

Jan 1, 1994

By Thais Cristina da Costa Caldas, Carlos Mauricio Fontes Vieira, Alline Sardinha Cordeiro Morais, Sergio Neves Monteiro

"This work has as its objective to evaluate the effect of the incorporation of a glass powder waste obtained from discarded and Hg-cleaned fluorescent lamp into clayey ceramics used to fabricate bricks and roofing tiles. Formulations were prepared with incorporation of the waste in amounts up to 10 wt.% into the clayey body. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa to fire at 850 and 1050°C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The microstructure of the fired ceramics was evaluated by optical microscopy. The results showed that the waste incorporation significantly improved the evaluated properties mainly at 1050°C.IntroductionFluorescent lamps use mercury as a main component for its operation. This metal is potentially toxic and can contaminate soils, animals and water bodies. The problem is aggravated if considerations are made with respect to the amount of lamps that are commercialized and discharged in emergent countries like Brazil [ 1].By using appropriate recycling processes applied to discharging fluorescent lamps it is possible to reuse most constituents of these lamps into new productive processes. A study has shown that one million common fluorescent lamps can generate 900,000 tubes of clean glass [2]. Moreover, this Hg-cleaned gloss may be recycled in different products.In fact, to recovery and recycle all materials that constitute the lamp instead of discharging them. This action protects the soil avoiding the formation of environmental passives [3]. It is also relevant to mention that the glass from fluorescent lamps is 100% recyclable while its permanence in the environment would correspond to very long time pollution, since its decomposition time is undetermined [4]."

Jan 1, 2011

By Y. A. Chang, L. M. Pike, C. R. Kao

"Knowledge of the site preference of ternary solute additions is essential to developing an understanding of how these solutes affect the properties of B2 intermetallic compounds. A quasichemical model will be presented which is able to predict the site preferences of dilute solute additions to tliple defect B2 compounds. The only parameters required are enthalpies of formation at the stoichiometric composition. General equations are developed which can be used to determine site occupations and defect concentrations for dilute as well as non-dilute solute additions. These equations use atom pair bond enthalpies as the parameters. It is found that the site preferences of dilute additions are not always in agreement with predictions based on the solubility lobes in ternary Gibbs isothelms. Predictions for dilute additions to NiAl and FeAl are compared to expel1mental results found in the literature. Satisfactory correlation is found between the model and the experimental results. In addition, the predictions from the model on vacancy concentrations in Fe doped NiAl are compared to recent experimental results by the authors.1.0 IntroductionIntennetallic compounds with the B2 crystal structure such as NiAl and FeAl have been investigated recently for possible use as structural materials in high temperature, oxidizing, and/or corrosive environments. The major limiting property of these materials has been a lack of sufficient room temperature ductility. Attempts to improve the ductility have often been made through ternary or higher order alloying. For B2 compounds, substitutional alloying additions can occupy either of the two sublattices and this site occupancy can be crucial in determining how the alloying addition affects the properties of the alloy. In this manuscript we will discuss the use of thelmodynamic modeling to predict the site occupancies of ternary alloying additions in B2 compounds with the triple defect structure."

Jan 1, 1996

By Riyad N. Ahmad-Bitar, Shadia J. Ikhmayies

"CdS/CdTe solar cells were built by depositing a 200 nm layer of Sn02:F on glass substrates by the spray pyrolysis (SP) technique, a 500 nm CdS:In layer by the same technique and a 1-1.5 µm CdTe layer by vacuum evaporation. The cells were CdCh heat-treated in nitrogen atmosphere for 30 minutes at 350 -.C. The photoluminescence (PL) spectra were measured at the CdS/CdTe interface for two cells with different values of the CdTe layer's thickness at temperature T = 60 K. A deconvolution peak fit was performed from which it is found that the peaks are characteristic of the solid solution CdSxTei-x· The parabolic relation that relates the bandgap energy with the composition was used to estimate x, where xis [S]/([Te]+[S]) and [Te], [S] are the concentrations of Te and S atoms respectively. The results show that the interface is smooth and the change of the bandgap occurs gradually.IntroductionCdS/CdTe heterojunctions represent a combination of materials promising various applications, and for solar energy conversion in the first place [1]. In photovoltaic cells the CdS material acts as a wide bandgap window. Direct bandgap CdTe with high optical absorption coefficient is used as an absorber [1]. Solar cells with efficiencies of 10 to 16% have been obtained with CdTe grown by close space sublimation, electrodeposition, vacuum evaporation and rf sputtering methods [2]. In this work the CdTe layer was prepared by vacuum evaporation because it results with films of minimum impurities, while the Sn02:F and CdS:In layers were deposited by the spray pyrolysis technique because it is a low cost method which enables intentional doping and large area thin films."

Jan 1, 2011