Search Documents

By M. Wong-Kian, L. A. Cornish, A. van Bennekom

Samples of four different satellite materials were prepared by either hot isostatic pressing (HIP) of the powder or tungsten inert-gas welding of rod onto a 316 L stainless-steel substrate. The samples were subjected to a series of comparative erosion corrosion tests, and generally the Hipped samples experienced between 13 and 24 per cent less loss in mass than the equivalent welded alloys. Resistance to erosion corrosion increased with increasing carbon, chromium, and tungsten contents. Metallographic studies indicated the differences in carbide content between the different satellite materials, and the differences in morphology between the Hipped and welded samples. Finer and more homogeneous microstructures were

Jan 1, 1995

By Thomas D. Henderson, Donald E. Crowell

INTRODUCTION This paper presents a "case history" of the steps taken to estimate capital and operating costs for a typical porphyry copper concentrator of ±9,070 metric tons (10,000 short tons) per day capacity. The concentrator described herein is hypothetical, but is based on experience and is, in effect, a composite of several actual projects. The numbers used are illustrative only and do not represent actual costs at any particular concentrator. These numbers are, however, representative of typical milling costs at one point in time, and. are sufficiently accurate to illustrate the cost estimating procedures described in this paper. It is not possible to publish actual, current milling costs and, in any event, actual cost figures quickly become meaningless in today's economic situation with various costs all rising at different rates. The paper is divided into three parts: (1) order-of-magnitude estimate, (2) feasibility study estimate, and (3) discussion of differences between estimated and actual costs.

Jan 1, 1978

By W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and trucks at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between the shovel and trucks with the new truck cycle times.

Jan 1, 1968

PURPOSE OF STUDY The case study was initiated because of the very real need to provide the best mineral inventory block estimates possible for the relatively new Sacaton mine. Sufficient mining had been done and records kept whereby it was possible to test the various estimation methods against detailed blasthole samples taken during mining. Three estimation methods were selected for testing: (1) the polygonal method, (2) the inverse distance squared method (IDS), and (3) the geostatistical kriging method. The results of the comparative analysis was thought to have very practical application to the selection of extension functions for future estimation of grade for mineral inventory blocks. GENERAL GEOLOGIC DESCRIPTION The porphyry copper deposit of the Sacaton open pit mine is related to small quartz monzonite intrusives of Laramide age which have been intruded into Precambrian granites. Both rock types act as host for the mineralization, which has been secondarily enriched sufficiently to constitute ore. The chalcocite enriched zone has been subjected to postenrichment oxidation processes with consequent partial destruction of the chalcocite blanket. Several mineralogical populations are represented in the total ore zone, but the blocks on the mine benches involved in the study were restricted to the top of the enriched zone. COMPUTATION OF MINERAL INVENTORY BLOCK ESTIMATES In order to make valid comparisons among the three estimation techniques, all of the inventories were prepared from diamond drill assay data used in the original engineering feasibility study. The data was taken from ex-

Jan 1, 1980

By Johnson N. W, Ralston J, Lauder D. W, Smart St C R

The flotation behaviour of the Hilton ore of Mount Isa Mines has been examined in the presence of two collectors (sodium ethyl xanthate (Ex) and sodium diisobutyldithiophosphinate (3418A)) over a range of flotation Eh values and collector additions. Tests were also conducted in the absence of collector to determine the relative contributions of natural and self-induced floatability of the major minerals in the feed. In these tests the influence of metabisulphite on the self-induced floatability of the minerals was also determined. Attention focussed on optimising the selectivity of galena flotation. It is shown that the Hilton ore sample contained lower levels of naturally hydrophobic iron sulphide minerals than are generally contained in the Mount Isa lead-zinc ore. Furthermore, the self-induced floatability of galena was less than that exhibited by the galena in the Mount Isa lead-zinc ore. Sodium metabisulphite (MBS) reduced the self-induced flotation of galena but had no effect on the natural floatability of the iron sulphide minerals.

Jan 1, 1991

By F Sandrone, J-P Dudt, J Zhao, E Paltrinieri

Tunnel boring machines (TBMs) excavation is nowadays more and more considered a valuable alternative to conventional tunnelling. As a matter of fact, thanks to its advantages such as greater rate of advance and safer working conditions, the application of TBMs has increased significantly in recent years. Despite the possible excellent performance of TBMs in favourable ground conditions, the advance rates could be significantly slowed down or even obstructed in limiting geological situations. This obviously traduces in potentially longer tunnel construction times and higher costs and, therefore, in a preference for conventional method. One of the major geological hazards encountered during tunnel construction, is related to the presence of fault zones or heavily jointed and fractured rocks. The most common geotechnical problems resulting from tunnelling in these difficult conditions include the instability of the excavation face, instabilities of side-walls producing large overbreaks on the tunnel profile, excessive deformations in case of squeezing grounds, frequently changing stresses in terms of magnitude and direction, high water inflows, etc. The decisions aids for tunnelling (DAT) is a model and a computer code that can be used to evaluate the influence of the uncertainties related to both the geological/geotechnical conditions and the construction process on final tunnel construction time and costs. In this framework, the DAT is used for assessing the effects that challenging ground conditions may have on tunnelling operations in terms of costs and delays. This is done by simulating the tunnel construction considering several geological profiles. The aim of the study is comparing different excavation methods (ie drill and blast versus TBM) in changing ground conditions along the tunnel alignment ranging from good rock, to very poor and fractured formations. The results show the impact, in terms of changing construction time and cost, of the excavation method versus the ground conditions.CITATION:Paltrinieri, E, Dudt, J-P, Sandrone, F and Zhao, J, 2014. Comparison of excavation methods in different ground conditions with the decision aids for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 573–580 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Hosseinzadeh Barforoosh, A Abedi, M Taji

The effect of blast loads on beams is one of the main issues in the analysis of steel structure. In this study, experimental tests on steel beam under blast loading, and also numerical simulation by the Autodyn software to analyse these structures, is discussed. Experiments on steel beam size of 12 by Emulite4 explosive with 30 mm diameter and cortex is done. The patterns of cutting and bending generated in the two tests (empirical and simulation) show a good match.CITATION:Taji, M, Hosseinzadeh Barforoosh, A and Abedi, A, 2015. Comparison of experiment and simulation of blast loading on the steel beam, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 161–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Klaus Rieker

Over the last 30 years Wayss & Freytag Ingenieurbau AG has gained a lot of experience in mechanized tunnelling on various major projects. During this period most important developments concerning the machine technology for EPB- and Slurry-Shields have taken place. Since the first application of a hydro shield for the Wilhelmsburg Collector project in Hamburg in the early seventies, several stages of development have led to the current state-of-the-art in mechanized tunnelling. The continuous improvement of TBM techniques allows the execution of high quality tunnelling, particularly with regard to maximum safety and efficiency. The practical experience of the construction companies is of essential importance in order to continue further development and improvement.

Jan 1, 2005

By R. F. Favreau, Patrice Favreau, Dennis Mahan

Cast blasting is becoming more and more popular, not only in coal mines but also in other operations which require excavation of an upper layer of waste rock to uncover temporarily and excavate a layer of ore, which may for example be material for the fertilizer industry.

Jan 1, 2014

By A Duran

When dealing with rocks in the geotechnical profession, a common activity involves providing an estimate of the intact strength. The tactile approach and descriptions of strength that apply to soils is well documented, can be readily checked through the use of a pocket penetrometer and are known to provide reliable estimates of strength. Moreover, although different soil strength classification systems are present, the bounds between classification classes are compatible across almost all documented classification systems. However, this is not the case for rock strength materials. There are numerous systems within the literature, some with different concepts, and almost all have different bounds to each strength classification. In this paper, the author presents seven classification systems for estimating intact rock strength and highlights issues in their implementation. Example cases are presented to discuss the typical concerns confronting field strength estimates.CITATION:Duran, A, 2014. Comparison of field estimated strengths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 101–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Delon Hampton, Francis K. Mensah-Dwumah

INTRODUCTION The state-of-the art in the area of soil-structure interaction is not sufficiently developed that one can accurately predict the earth load distribution on buried structures. This lack of knowledge has led to the use of high factors of safety in their design and conservative assumptions for the loading diagrams. As a step towards the improvement of the design methodology for buried structures, it is important to be able to apply new analytical techniques and monitor the performance data obtained on full-size buried structures. The performance data should preferably include: 1) the actual stress distribution on the buried structure, 2) stress distribution in the buried structure and surrounding soil media, 3) vertical and lateral movements in the soil adjacent to the buried structure, and 4) deflection of the buried structure. Brown (1967), Davis (1972), Krizek, et al (1974), Krizek and MacQuade (1978), and some few others have compared the performance of full-size culverts with finite element results. Despite all these efforts, a complete understanding of the soil-structure interaction problem has not yet been fully achieved. In an effort to make improvements in the existing design procedures for buried structures constructed in an open-cut, the Department of Environmental Services (DES), Washington, D.C., in conjunction with Howard University, undertook a detailed study of Section II of the Capitol Hill Relief Sewer (CHRS). Inclinometers were used to measure lateral movements of the excavation wall and the total normal interface stresses acting on the concrete sewer were obtained using glotzl total pressure cells. This paper describes the results of the field instrumentation program for acquisition of data, their comparison with the design assumptions, and the results of a series of post-construction finite element analyses of the CHRS project.

Jan 1, 1979

By Jr. Pickering

Commercial quality kaolin deposits occur in fluvial sediments in both central-eastern Georgia and in the eastern Amazon River area of Brazil. Distinctive coarse and fine particle size kaolin deposits are present in both areas; they have many remarkable similarities for mineral deposits occurring at such wide geographic separation. Industrial, mineralogical, crystalline, and chemical resemblance of the coarse and fine kaolin deposits from the two areas will be described in detail. Knowledge of similarities of the Brazilian clays to those which have dominated world production in Georgia will help to develop superior quality kaolin products for world use in paper, paint, plastic, ceramic, and other applications.

Jan 1, 1997

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion (Li-ion) battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V and 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicate that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Jan 1, 2024

By L. Yuan, J. Soles, W. Tang, R. Thomas

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12V, 24V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Feb 1, 2023

By G. I. Mathieu

"An experimental study was carried out to evaluate the performance of column flotation versus conventional flotation for the recovery of molybdenite from a Newfoundland ore. The objective was to verify the claims made by the inventors of the flotation column, Messrs. Pierre Boutin and Remi Tremblay, that their apparatus reduces the entrainment of fine gangue and other mineral impurities in the froth product. The research included a factorially designed series of tests to determine satisfactory operating conditions of the column. These provided a basis for comparative flotation tests with column and Denver cells. In the course of the work, the action of a few depressants was studied. Results indicated greater selectivity in the column and reduced reagent consumption."

Jan 1, 1972

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012

By E. A. Sondreal

Requirements of flue gas desulfurization (FGD) for Eastern and Western U.S. coals will not be the same because of differences in coal sulfur content, ash analysis, and beating value. The effects of these differences and of limited availability of water in the West are the subjects of this paper. Eastern and Central bituminous coals are generally high in sulfur and require removal efficiencies in the range of 70 to 90 percent to meet the Federal emission standard of 1.2 lb SO2/MMBtu. Ash in Eastern coals is low in alkali content and is relatively insoluble in scrubber solutions. High sulfur content and market availability make salable product methods more attractive in the fast and Central United States than in the West. Western subbituminous coals and lignites are generally low in sulfur content, however, only a few deposits could reliably meet the Federal emission standard without FGD, Required removal efficiencies generally fall in the range of 0 to 60 percent to meet the 1.2 lb SO2/MMBtu limit. If the standard were raised to 2 lb S02/MMBtu, approximately two-thirds of Western coals could be burned without FGD. Some Western coals contain ash high in alkali, some of which is soluble in scrubber solutions. This complicates scrubber chemistry, but it also provides the meant for displacing some or all of the limestone requirements when only moderate S02 removal is required. Dry areas in the West would benefit from full commercial developement of dry processes of FGD.

Jan 1, 1974

By E. A. Sondreal, P. H. Tufte

Flue gas desulfurization when burning western U.S. coals can be expected to be easier to achieve and less costly than when burning higher sulfur eastern and central coals. However, western coals cannot generally be burned in compliance with federal and state new source emission standards without some degree of control. Western coals and lignite represent about 20% of total U.S. recoverable reserves with 90% of that strip minable, and their production is predicted to increase from the 60 million tons mined in 1973 to 300 million tons in 1985. Most will be used for electric power generation, where low sulfur content is a paramount concern. Western coals are predominantly below 1% sulfur; low compared with typical values of 2 and 3% for eastern and central coals. Coal cleaning for removal of sulfur is not commercially practiced on Western coals, which typically contain half organic and half pyritic sulfur. A fraction of the pyrite sulfur could possibly be removed, but the

Jan 1, 1976

The General Purpose Simulation System (GPSS) is a computer simulation language that has been used for simulations of open pit haulage operations since the 60's. It is easy to learn, simple to use, and has a block-diagram structure that is amenable to load-haul systems. However, due to its lack of flexibility, there are situations where another language should be chosen. This paper reviews the characteristics and capabilities of both GPSS and FORTFAN with regard to open pit shovel and truck simulation. The relative advantages and disadvantages are highlighted and a case study presented along with comparative results from two computer models (one written in GPSS and the other written in FORTRAN).

Jan 1, 1986

By S J. Clarke, G Sieders

Double corrosion protection (DCP) rock bolts have evolved to become complicated assemblies comprising numerous components. This complexity is mainly associated with durability considerations including potential exposure to adverse groundwater conditions and ensuring separation of dissimilar metals within the bolt assembly itself.Recent progress in the construction of glass-fibre reinforced polymer (GRP) rock bolts have the potential to provide a viable alternative to conventional steel rock bolts in civil tunnelling applications. The durability of the material results in a much simpler bolt detail and permits the use of resin rather than solely cement based grouts.This paper presents the findings of the comparative structural testing of GRP bolts with conventional DCP steel bolts. The axial load performance, including stiffness, ultimate capacity and ductility of bolts are compared. Shear behaviour of bolts is considered, including durability issues associated with damage to the plastic sleeve used in DCP bolts.The paper also considers other issues which are relevant to the design of temporary and permanent rock bolts used in tunnel support, such as initial tensioning and grouting. Long-term performance, including durability and creep are also reviewed.CITATION:Clarke, S J and Sieders, G, 2014. Comparison of glass-fibre reinforced polymer rock bolts with double corrosion protection steel rock bolts for use in tunnel applications, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 237–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014