Search Documents

By U. S. Sawant

During the last few years, Process Machinery Division, Rexnord, has conducted extensive research on the effects of cone crusher variables such as speed, throw and cavity design on the productivity of the crushers. Simultaneously, Rexnord's engineers have developed advanced design and testing techniques and criteria that assure efficient and reliable crusher designs. The combination of these two has resulted in a design of the 2390 Omnicone (1000 hp) crusher which fits on an existing 7 ft. Symons foundation and yet is capable of producing twice the tonnage compared to our 7 ft. super heavy duty (500 hp) crusher. Both speed and throw can be varied to give a wide application flexibility from making twice the tonnage to the finest product. The 2390 Omnicone also incorporates innovative features such as full balance, cavity clearing, adjusting under load with automation capability, maintenance-free seals, one head for all cavities, ease of maintenance and servicing, etc.

Jan 1, 1987

By A. J. Magerowski

Energy consumption is a main component of operational costs for the comminution of mineral bearing ores. Reduction of energy consumption has continually been addressed by mill operators and equipment manufacturers. Our testing over the last few years strongly indicates that the overall energy needed to comminute a mineral bearing ore can be brought down significantly, if more work is done in the crushing stages of the comminution circuit.This calls for uprating of the conventional crushing equipment into a new generation of crushing equipment to produce finer products. This will result in the emergence of new ideas in the design and application of equipment and corrnninution circuits.

Jan 1, 1986

By Ronald B. DeDiemar

This paper will present the intrinsic factors of a cone crusher that affect performance, develop and define an ideal feed gradation for a cone crusher and, finally, bring out an important new development in computer design of crushing chambers and show an ability to predict crusher performance without trial-and-error methods.

Jan 1, 1979

By M. D. Flavel, J. C. Motz, G. V. Jergensen

Introduction Compared to the gyratory crusher, the cone crusher is character¬ized by its higher speed and a flat crushing chamber design which is intended to give a high capacity and reduction ratio for materials suitable to this type of processing. The aim is to retain material longer in the crushing chamber to do more work on material as it is being processed. A concept of how a piece of stone might flow through a secondary crushing chamber is shown in Fig. 45. The number of times material will be nipped during crushing will depend on material size, friability, and the geometry of the crushing chamber as well as its speed and eccentric throw. Cone crushers are usually specified in terms of closed-side setting (CSS) and a given quantity of material passing a particular square-mesh screen size. A criterion of product passing closed-side setting is often available. This value will vary according to the particular crusher design and the details of its applica¬tion. Essentially, cone crushers can be classified into distinct types, depending on their duty. Crusher sizes for all duties are described by terms arising out of common industry usage, such as 3-ft, 7-ft, etc., which refer to the crushing-head (mantle) diameter. At present the range of sizes available varies from approximately 2 to 10 ft diam. Weights vary in the range of 5 to 200 tons, and connected horsepowers range from 10 through 700. There are so many variations that specifics should be obtained from machine manufacturers. The crushing chambers that are fitted to various machines are also often referred to by terms arising out of common usage, such as standard for secondary crushers, and short head for tertiary crush¬ers, which refer specifically to the Symons design. Also used are more specific but equally vague descriptions, such as coarse, intermedi¬ate, and fine chambers. Some manufacturers such as Allis-Chalmers with their Hydrocone crushers refer to the model number of the machine by the feed opening and the diameter of the mantle. For example, a Model 10-84 Hydrocone crusher has an 84-in. diam man¬tle, and is capable of accepting a 10-in. diam sphere at the feed point to the crushing chamber. Rexnord and Telsmith define crushing cavi¬ties in their capacity tables as feed openings at minimum recommended discharge settings (closed-side settings). Each practice offers guidelines which should be carefully defined for the specific crushing problem. The utilization of a cone crusher depends on how well it is controlled and the features of the circuit in which it operates. Normally, it will operate in the range of 75 to 85% of the peak capacity. It is likely that industry pressures will call for a standarized de¬ applied crushing power. Experience has shown that the crushing process is more controllable if certain reduction ratios are adhered to for each stage. Technically, this is defined as that size of feed (in. or mm) of which 80% will pass, divided by the size of the product (in. or mm) which 80% will pass. Secondary Crushers These are the cone crushers which accept suitable feed size material either prepared by a primary crusher or occurring naturally, and reduce it to a size suitable for marketing in one stage, or make feed for subsequent crushing or grinding stages. Secondary crushers have feed openings of 4 to 25 in. in the larger (7-ft) models down to a 2'/a to 4 in. in the smallest 24-in. models. Reduction ratios normally range between 3:1 and seldom more than 5:1. In the 7-ft models, the cone crusher typically makes a product all passing 2 in., but this is dependent on the machine design and properties of the material being treated. Secondary crushers most commonly operate in open circuit. They also are operated in closed circuit with a vibrating screen, depending upon product requirements and conditions where the reduction ratio does not cause excessive power draw and build-up of circulating load. Screening ahead of secondary crushers is generally recommended, especially where the feed contains more than 25% material smaller than the desired closed-side setting. Tertiary Crushers These are cone crushers that normally take secondary crusher product and reduce it to a marketable product or make it suitable for subsequent comminution steps. The reduction achieved is a func¬tion of the crusher design and the properties of the material to be treated. The reduction ratio is normally in the range between 1.5 and 2 to 1, and seldom more than 3 to 1. The tertiary crusher normally operates in closed circuit with a vibrating screen and makes a product smaller than all passing 'h or 5/8 in. Fine Crushers Sometimes these machines are called sand crushers and are called by various manufacturer brand names, such as Gyradisc, Hydrofine, V.F.C., and others. A cross section of a Symons Gyradisc crusher is shown in Fig. 46. Essentially, these crushers would be used in a fourth-stage crushing operation, but could be called on to reduce a screened feed size fraction from a secondary or primary crushing operation. This type of crusher normally receives feed no coarser than 1'h in. that is scalped of all over-sized material and operates in closed circuit with a vibrating screen. For average materials, typical product is '/e in. top size, although a -10 mesh product can be produced on those materials having suitable characteristics. The crusher is nor¬mally operated in a separate circuit from the main crushing plant because of the variations in output rates that are caused by varying physical properties in the feed. The reduction ratio is generally less than 2:1, and circulating loads are generally high. More interparticle crushing takes place in these machines than with conventional cone crushers and capacities can be more sensitive to changes in moisture content, feed size graduation, and other physical properties. Design Features For the various applications, crusher manufacturers normally have a range of crushers of different sizes and power ratings to select from.

Jan 1, 1985

By J. D. Prater, H. R. Spedden, E. E. Malouf

Application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production, whereas formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing so1utions.l Detailed investigations made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a precipitation cone-type recovery system having advantages over older methods.

Jan 4, 1966

By Baltus Cornelius Bonse

Foi desenvolvido um composto de elastômeros termorrígido (ebonite) para a fabricação de um selo mecânico de vedação de hélices de barcos, para substituir os modelos comumente encontrados de cerâmico, que possuem alto custo e são fabricados no exterior, e de borracha com face em Teflon®, que apresentam problemas de adesão na linha de junção entre estes materiais, resultando em vazamentos. O composto de elastômeros deveria possuir dureza em torno de 90 Shore D, baixo coeficiente de atrito, resistência térmica, a abrasão e a intempéries marítimas, ao ataque de radiação UV e ser autolubrificante. A formulação que resultou no melhor produto consistia das borrachas natural, nitrílica, nitrílica carboxilada, e fluorada (Viton®), aditivadas com alto teor de enxofre (37,5 phr), cargas reforçantes, plastificantes e lubrificantes sólidos, entre outros aditivos. A aditivação e mistura das borrachas foram realizadas em misturador interno Banbury e misturador de cilindros aberto, enquanto a conformação e vulcanização dos corpos de prova e dos selos foram realizadas por prensagem a quente. Foram realizadas análises de curva reométrica, morfológicas por microscopia eletrônica de varredura, de resistência à tração, rasgo, dureza e de abrasão em torno mecânico simulando a pressão de vedação em atrito com o aço inox girando a 800 rpm. O êxito do selo ficou evidente, pois após a montagem em barcos, durante um ano tem realizado com sucesso a sua função.

Aug 8, 2018

Africa is rich in natural resources, much of which remain untapped. Despite that, international mining companies have largely stayed away from the continent due to political instability in many countries, lack of infrastructure and the inability to gain control of mineral deposits. Today, optimism is growing concerning African mining. Many of its nations are moving toward privatization of their mining industries. They see it as a way to improve the lives of their populations and become politically stronger. Ministers from 22 African nations were Denver, CO in June for the World Bank's Multilateral Investment Guarantee Agency's Fourth Annual African Mining Investment Symposium. The three-day symposium drew more than 400 mining executives and government representatives. Foreign mining investment in Africa is on the increase. In 1996, international mining companies spent about $418 million on exploration. That is more than double the $190 million spent in 1994. Mining executives say the mining climate in Africa is improving because countries are privatizing the industry and rewriting mining laws that encourage natural resource development. They estimate that private mining firms now control about 80% of mining today. Mine development will help lift the living standards for Africans, the ministers said. The average income for ordinary Africans is about $500 a year. If this new mining boom continues, citizens of nearly all African nations will reap the benefits of better infrastructure and government services, as well as more higher paying jobs, the ministers said. They also issued a word of caution to mining companies attempting to join in the African boom. Concerns are being raised about the treatment of villagers and the environment. In the past, foreign companies would "behave about like colonial masters," said Gerald Ssendaula, natural resource minister for Uganda. Africa is in a different position now, he said. "Now we are solving our own problems." Mining companies must respect local communities or risk creating unrest that will threaten fragile new governments, said Akolang Tombale, chief geologist for Botswana. On the other hand, he said villagers must accept that mining development will benefit them. "They feel these are their natural resources. There must be a mutual interaction between the companies and the people."

Jan 1, 1997

Following the suggestion of Engineering Council and at the direction of, the President, representatives from each of the Federal Government bureaus interested in map-making were called into a conference for the purpose of coordinating all of the Government's map-making activities. This conference has now reported back to the President the results of its findings, which indicate that Engineering Council's recommendation in this matter was well founded. While the conference report states that its members were of the opinion that little duplication of effort existed, it recommends the formation of a permanent Board of Surveys and Maps. An extended review of the map-making activities, which is given as an appendix to the report, indicates that this recommendation is a logical step. The conference recommendations concerning this Board of Surveys and Maps are as follows: (1) the Board is to he com-posed of representatives of mapping bureaus to be assisted by outside engineering organizations, which have been named above; (2) the estab-lishment of an information office in one of the Government bureaus, preferably the Geological Survey, which is to be under the supervision of the Board and is to be a mapping information clearing house for the Government and outside engineering organizations; (3) copyright laws are to be so changed that copies of all. maps made in the United States and with Governmental authority, will go to the central information office; (4) the Government departments are to receive orders to cooperate, with the Board; (5) future topographic maps of all kinds are to conform with specifications for the standard topographic map; (6) the U. S. Coast and Geodetic Survey to have supervision of final adjustment of all important control data under specifications approved by Board of Surveys and Maps; (7) surveys in the form of maps and publications are to be issued as soon as possible after field work has been completed; (8) program of the Interdepartmental Committee on Aerial Surveying was approved. Outside technical and scientific organizations that are called in for consultation are to operate in an advisory capacity only, responsibility for action on Governmental work is. to rest solely with the Governmental agencies.

Jan 12, 1919

By W. R. Toeplitz

Probably a more descriptive title would be "Much Ado About Nothing." By "nothing," of course, I refer to the porosity which is the main feature of this type of bearing. Porosity has a decided effect on the manufacturing techniques, the structure and physical properties, the oil content, and on the installation and service of oil-retaining porous bronze bearings. A simple curve can be drawn by plotting specific gravity along the abscissa and percentage of porosity by volume on the ordinate. A bronze composition, analyzing 89 Per cent copper, 9.75 Per cent tin, and 1.25 per cent graphite, has an absolute solid specific gravity of 8.5. At this specific gravity, of course, occurs the point of zero porosity. Conversely, at loo per cent porosity, the specific gravity is zero. A similar curve can be drawn for bearings impregnated with oil; the only change being that the specific gravity at loo per cent oil will be 0.89 if we assume that that is the specific gravity of the lubricant. The curve is useful in determining the oil content by volume for any specific gravity. The normal range of oil content for porous bronze bearings of this composition is from 35 to 16 per cent, which is in the specific gravity range of from 5.8 to 7.3. In addition to the amount of porosity, the type of porosity is important. The first consideration here is that the porosity must be intercommunicating. This can be determined by a number of simple tests. The first method, which is very accurate, is to extract the oil in the bearing by cycling

Jan 1, 1945

By R. R. Hoffman

The name L'brush,l as applied to the parts to be briefly considered in this paper, is not clearly descriptive of the design and function of those parts when the usual definition of the word is applied. In a general way, the brushes to be considered here are the parts employed on certain types of electrical equipment to facilitate the transfer of electrical current between a rotating or moving element and a stationary element. These machines are generally motors and generators of both the slip-ring and commutator types, rotary converters, battery charges, etc. Parts that serve a similar purpose on relatively slow or intermittently moving devices such as rheostats, switches, controllers, etc., are generally referred to as contacts. A few special applications involve the use of current-carrying washers, rollers, bushings, etc. As may be inferred, therefore, the design of these brushes and allied parts is dictated by both electrical and mechanical considerations. In most cases these factors are closely interrelated, and unfortunately many of them are not subject to exact scientific or mathematical analysis. Special Advantages Since brushes operating on direct-current machines must carry the load current, resist destructive action from voltage induced in imperfectly compensated armature coils, and in addition act as a bearing material, maintaining intimate contact with the commutator at peripheral speed, which may be as high as 70 miles per hour it is difficult to obtain in one brush the ideal properties necessary for perfect functioning under all operating conditions. The engineer-designer, therefore, when selecting a brush for a specific application, must choose a grade that possesses the characteristics most adequate to meet the conditions involved. In many cases a characteristic that makes a specific grade of brush the ideal selection for one type of machine may be of secondary importance to some other property when the brush is applied on another machine. Frequently different grades of brushes must be applied to the same type of machines when they operate under different or unusual atmospheric conditions. Completely satisfactory brush operation depends on freedom from appreciable sparking, minimum electrical and mechanical losses, negligible commutator or slip-ring wear, uniform film over the commutator or slip ring, quiet operation and good brush life. The ability to produce special structures, and to combine in widely varying proportions materials that are incompatible, through conventional melting and alloying procedures has been the basic contribution of powder metallurgy to the solution of problems involving brushes and allied parts. This is especially true where current-carrying capacity is a major factor, owing to the limitations of all carbon or all graphite brushes in that respect. Metal-graphite Brushes With very few exceptions, friction between moving elements. across which

Jan 1, 1945

By F. R. Hensel

The present paper describes a number of experiments with fine silver, coin silver, silver-cadmium oxide and silver-nickei-copper compacts, prepared by powder metallurgical methods. The test data are of a preliminary nature, since most of the work was exploratory. Fine Silver Eject of Compacting Pressure on Hardness and Density during Cold and Hot Pressing The cold-welding properties of silver have received considerable attention and the welding characteristics are functions of such variables as: cleanliness of metal particles (impurities and adsorbed gases), chemical nobility of particles, plasticity and hardness, particle assortment, particle shape, particle porosity, apparent density, temperature, pressure, time, recrystalliza-tion characteristics. Chemical nobility, plasticity and low temperature of recrystallization after work-hardening are responsible for the excellent low-temperature bonding properties of silver. Several series of compacts were pressed at pressures of 5, 10, 20, 30, 40, 50, 60 70 and 80 tons per square inch, at temperatures of 32°C. (room temperature), l00°, 2000, 300°, 400°, and 450°C. Silver powder of minus 325-mesh, produced by displacing silver from a nitrate solution by means of copper, was used. The density was calcuiated from accurately measured and weighed compacts. The hardness was measured on the Rockwell F scale. The investigation shows that an increase in pressure promotes a higher density and hardness regardless of pressing temperature, up to a temperature of 400° C. The pressure-density curves at various pressing temperatures are shown in Fig. I, the pressure-hardness curves at various pressing temperatures, in Fig. z. The greatest increase in both hardness and density was obtained in the pressure range of 5 to 20 tons per square inch. A compact from each series was annealed at 300°C. in air, for various lengths of time. The hardness values after annealing are shown in Table I. A minimum hardness was obtained after one hour of annealing. No change in density occurred during annealing. The maximum density was obtained at 80 tons per sq. in., and at this pressure the hardness is equal to that of hard-drawn wrought

Jan 1, 1945

By F. R. Hensel

P. R. Kalischer.*—I should like to amplify a little one of the points made by Dr. Hensel, and rather violently disagree with him at the same time. He brought out the point that when the higher forming pressures are used on the green compacts there is a marked decrease in the density as sintered. We found that to be true and, of course, many of you notice that that is true with copper compacts also. But, in my opinion at least, it is not true that the expansion is due to entrapped air. We have vacuum-pressed both silver and copper compacts and obtained almost exactly the same numerical expansion as we secured by pressing in air. The powder, however, that is vacuum-annealed does show a slight decrease in expansion on sintering, but almost the entire increase on expansion can be overcome by very slow rates of heating. And it is our opinion that a majority of the expansion is due to dissolved oxygen in the discrete metal particles themselves rather than to entrapped gases. Another interesting observation that we have made is that often with silver or copper compacts it is desirable to silver solder or braze the compact into some part of a piece of equipment after completing powder metallurgical operations on it. If such a compact is sintered and coined, say a silver compact, given an initial forming pressure of 10 to 15 tons per square inch, and sintered, there is an adequate amount of shrinkage and it can be coined at about 50 or 60 tons per square inch and bring up the density nearly to theoretical. If, then, that compact is silver-soldered into some part of a fixture or a machine, it will expand very beautifully, and the only way that this can be overcome. as far as we know, has been to reanneal after the coining operation at a temperature higher than is to be used in any subsequent operation. In that way, a density very nearly theoretical can be achieved, but the coining operation cannot be carried to the excessively high pressures or expansion and bubbling of the compact will occur again.

Jan 1, 1945

By F. H. Rhines

Page Foreword. By F. N. Rhines............................525 Design Factors for the Metal Forms with Which Powder Metallurgy May Compete. By Fred P. Peters...................... ......527 Discussion..................................530 Powder Metallargy as Applied to Machine Parts. By A. J. LanghamMer........531 Discussion......................... . Pole Pieces for Electric Motors from Iron Powder. By F. V. Lenel...........535 Discussion....................... . Bearings from Metal Powders. By W. R. Toeplitz.................542 Discussion.........................'.........549 Brushes and Allied Powder-metal Parts. By R. R. Hoffman . .............'550 Electrical Contacts Manufactured from Metal Powders. By E. I. Larsen........554 Sintered Magnets. By C. B. Fulton........................557 Friction Articles from Metal Powders. By C. T. Cox..................565 Discussion..................................567 Certain Characteristics of Silver-base Powder Metallurgical Products. By I?. R. Hensel and E. I. Larsen........................ ....569 Discussion............................... . . . . 579 Some Properties of Sintered and Hot-pressed Copper-tin Powder Compacts. By C. G. Goetzel..................................580 Discussion..................................593 The Sintering of Metal Powders—Copper. By C. J. Bier and J. F. O'Keefe......596 Some Experiments on the Effect of Pressure on Metal-powder Compacts. By Jerome F. Kuzmick..................................612 Discussion.................................. 630

Jan 1, 1945

By Fred P. Peters

At first glance this paper may seem unique among those comprising this symposium on designing for powder metallurgy, since it is evidently concerned with everything but Powder metallurgy. This paradox mill be at once resolved, however, when the real Purpose of the symposium meeting is understood—to present factually and objectively the things that can and cannot he done with powder-metallurgy methods, and especially to set forth with brutal frankness the limitations of Powder metallurgy, so that costly over-enthusiasm and misapplication may be prevented. Since much of powder metallurgy's future development (and many of its present disappointments) has been in competition with other and long-established methods of fabricating parts, it is easy to see that its true competitive possibilities in any given case cannot be accurately appraised without rudimentary knowledge of what the competition can do. This paper, therefore, presents a few reminders of things you all know—a background to be kept in mind as you examine the data on each of their specialties given by the authors of the papers that follow. From the standpoint of the design engineer powder metallurgy is often in Competition with one or more of the following: sand casting, die casting, permanent-mold casting, precision investment casting, ma- chined bar stock, screw-machine parts, cold-heading, drop-forging, and stamping and drawing. We will here briefly discuss each of these individually, and set forth so, rough (and therefore dangerous) generalizations about its competitive position, especially with respect to powder metallurgy. Sand Casting Sand-casting of small parts is sometimes an inexpensive method of manufacture, for its raw-material costs (i,e., for gray iron) are the lowest of the various methods and it involves the use of no tools and dies of jewelry quality. its design flexibility— that is, the ability to make complicated, cored and undercut parts in one piece—is about the highest of the competing processes and in this respect it can do many things that are impossible by powder metallurgy. For small castings its production rates may be higher, by using multi-impression molds, than can be achieved with parts of the same size by powder metallurgy. But its labor charges for melting, pouring, patternmaking and molding are comparatively high and the waste it entails in gates and risers is always considerable. Tolerances of sand castings are wide (+1/6 to 1/32 in- per in.) and where precision approaching that of powder metallurgy is required sand castings must be machined to final size, thus increasing their cost. Steel sand castings are more expensive and less precise than iron, and nonferrous the most costly of all.

Jan 1, 1945

By Fred P. Peters

T. D. Yensen.*—As my information is of a negative nature, I think it belongs under this paper. We are particularly interested in magnetic materials and we would like very much on occasions to make use of powder metallurgy. We have tried repeatedly to use powder metallurgy in preparing our nickel alloys but always. with negative results; that is, we cannot get as good magnetic properties by powder metallurgy as we can by starting with a molten material. We have tried by all possible means to make materials' like 50 per cent iron-nickel alloys by powder metallurgy. The compacts can be regularly lorged and rolled but no matter what we do in the way of annealing, the magnetic properties come out very much poorer than if we start with molten material. F. V. Lenel. †—I want to mention one characteristic of articles made from metal powders which distinguishes them from die castings; that is, their wear resistance. Die castings usually are made from zinc or aluminum alloys and a few copper-zinc alloys; all of them are comparatively soft and not very wear resistant. I know of a number of cases where powder metallurgy rather than the die-casting method was used for producing a certain part because higher wear resistance was needed than could be attained in die castings. A, J. LanghammeR.*—The subject of powder metallurgy is somewhat difficult to discuss, and portray, in the time that his been allotted. Most of you would rightly be bored if we went into details. However, I will cite one incident that possibly will help illustrate some of the potentials. Last summer I was in Washington and met Navy officials for the purpose of studying the possibility of making a certain part by powder metallurgy. The part is highly intricate and I happened to remark that the material cost would be high; that is, the cost on one raw material. Promptly a high-ranking Navy officer said: "Mr. Langhammer, if you must pay x dollars a pound for the raw material, but achieve the desired results, the cost of the finished part would still be low."

Jan 1, 1945

By C. T. Cox

W. A. Reich.*—I should like to ask Mr. Cox if he has any information on the change in

Jan 1, 1945

By F. V. Lenel

This discussion is concerned with the method of manufacturing, the design possibilities, and the properties of pole pieces for direct-current electric . motors and generators made from iron powder. In such applications as pole pieces, the electric and magnetic properties of the material are of major importance, therefore they are discussed somewhat more fully. However, the main advantage in making pole pieces from powders lies in the rapid and inexpensive method of manufacturing these pieces, and in the flexibility of design, rather than in their superior electrical properties. As a matter of fact, pole pieces from iron powder have found their principal field of usefulness in small electric motors for controls and similar applications where the highest possible flux density in a given design is not required. Fig. I shows a number of different designs for pole pieces made from iron powder. The steps involved in fabricating them are: (I) briquetting—with each stroke of the briquetting press a complete . pole piece is produced; (2) sintering, and (3) sizing, which is a one-step coining operation in a hand-operated punch press. Conventionally small pole pieces are made from laminated electrical sheet steel stock by punching out the laminations and riveting them together (Fig. 2). The powder method has the advantage of being rapid and inexpensive; also, it makes possible the molding of pole pieces with a round hub, which are better from a design standpoint, as will be shown later. It is difficult to make such round-hubbed pieces from laminated stock. The pole pieces could, of course, be machined from solid stock, but this method is not widely used. The raw material for making pole pieces from powder is straight iron powder without the addition of any alloying ingredients. However, the grade of powder used is of considerable importance, as will be shown later when the influence of the grade of iron powder upon the magnetic properties is discussed. Pole pieces are briquetted in the same way that other iron-powder machine parts are made. Because the pole pieces are flanged—i.e., they have a hub and a wing section—they are made in presses that apply pressure from both ends. For best mechanical and magnetic properties, the density throughout the piece should be even and also should be constant from piece to piece. For that reason a powder of constant compressibility from batch to batch is needed for briquetting pole pieces. One method of obtaining the required magnetic properties is to sinter the pole pieces at temperatures higher than are used for most iron-powder parts. A temperature of 2400°F. and an atmosphere of hydrogen has been found satisfactory. No automatic furnaces of the roller hearth or mesh-belt type have yet been developed for such high temperatures. A box-type furnace heated with Globar heating ele-

Jan 1, 1945

By F. V. Lenel

R. P. Seelig.*—Dr. Lenel is to be congratulated on his presentation of a particularly interesting paper describing the use of the powder metallurgy process for the production of magnetic pole pieces. The only thing that might be added is that we have been successful in producing pole . pieces with a narrow hysteresis curve by the use of considerably lower sintering temperatures than the ones used by Dr. Lenel. It is quite possible that this use of lowe- temperatures has considerably widened the field of commercial application for pole pieces made from metal powders. Development work is currently being done on an a.c. application of a sintered iron part. However, I am in full agreement with Dr. Lenel that if eddy currents are an important factor in the application, we cannot substitute sintered material for laminated sheet-metal structures. Mr. Peters' remarks concerning the limitations of machine parts were well taken. The emphasis of the limitations makes it easier to define clearly what we can do and-what the advantages are of machine parts made of metal powders. When I mention metal-powder machine parts, I mean those of relatively high density, although complete elimination of porosity is not possible at this time. The limitations of the field for this type of parts are largely economical. I believe that Mr. Langhammer has made that point very clear. The following questions are very often asked: How large a part can you make? How close can you hold the dimensions ? How fast can a part be produced? In a majority of the cases, it depends on the cost at which the part can be produced. A large variety of shapes and sizes of a number of materials can be formed. However, the main requirement in this field of endeavor is whether this can be done more economically by powder metallurgy than by other manufacturing methods. As a general indication, it may be stated that densities up to 95 per cent of that of rolled material can now be produced commercially in simpler parts. Tolerances of plus or minus 0.001 in. are common, but where special conditions justify, closer tolerances can be held; we are producing a part of which one dimension is held to 0.0003 inch. Finally, as far as maximum size is concerned, technically this would depend on the capacity of the press and furnace equipment available. Actually, we find that the economical limit of powder-metallurgy machine parts is approximately one pound. From there on, each individual case must he studied on its own merits.

Jan 1, 1945

By C. R. Fulton

The idea of making permanent magnets by sintering is not a new one, but until the introduction of the iron-nickel-aluminum permanent-magnet alloys there was little need for such a process. Permanent-magnet alloys in use up to the time of this development could be forged and machined to the exact size or shape required without too much difficulty. These new Fe-Ni-A1 alloys, which have become known as Alnico in this country, soon became very popular because of their superior magnetic properties, but when they were made by casting they did have some disadvantages when compared with the older type of permanent-magnet steels. Among these disadvantages were the following: 1. It was almost essential that they be cast to size, since they could not be readily forged or machined. The material could be ground but this was quite expensive, particularly for small magnets in large quantities. 2. The material had a large grain size and was mechanically weak. 3. Close tolerances could not be held and on small magnets this meant grinding almost the entire magnet. Because of the brittle nature of the material, there was considerable loss due to chipping and cracking during these grinding operations. 4. Because of its high aluminum content, the molten alloy had a high surface tension. It was difficult to prevent loss of aluminum by oxidation during the melting operation. In view of these difficulties it is not hard to understand why a process for sintering alnico was developed, or why sintered alnico has come into such widespread use in recent years. It might be well to qualify this by saying that it has come into widespread use for small magnets weighing 2 oz. and less, of the type shown on Fig. I. In this size range, sintered alnico has been able to compete in price with cast alnico. Magnets larger in size, of the type shown on Fig. 2, can be made but they do not compare favorably in price with the cast material. An idea of the range of sizes that have been produced is given by Fig. 3, which shows a small magnet weighing 0.006 oz. and a large magnet with a steel insert weighing 4 lb., both made from sintered alnico. Magnets weighing more than 2 oz., however, should not be made from sintered

Jan 1, 1945

By Jerome F. Kuzmick

Many investigations have been made on the effect of the variables of pressure, sintering temperature and sintering time on the physical and microstructural charactcristics of metal-powder compacts. Severa1 such investigations have indicatcd that pressure is the least important of these three factors in an attempt to secure a dense. strong compact by a simple coltl-pressing and sintering procedure. However, it was felt that a further study of the effect of pressure on pressed and sintered metal powder compacts might prove interesting, for the following reasons: In work done in the past on the effect of pressure, temperature. arid time, the, metal-powder compacts were subjected to long sintering periods, and temperatures right up to the melting point of the metal were applied. It was thought that pressure might exert a more profound effect under short-time simtering and within narrower ranges of temperature. such as normally would be applied in large-scale production of metal-powder parts. 2. It was hoped that something further might be learned of the nature of the bond in pressed and sintered metal-powder compacts. 3. It was thought that interesting infor mation concerning the work-hardening effect of pressure on the crystal structure. of sintered metal-powder compacts would be obtained. Procedure Rectangular bars, 2 by 1/2 by 1/4 in. were molded from the following metal powders: Atomizcd till powder, 325-mesh Atomized aluminum powder, 325-mesh Reduced copper powder, 100-mesh Electrolytic iron powder, 100-mesh Atomized 70-30 brass powder, l00-mesh The, till powder was molded at various pressures up to 40 tolls per sq. in. This was the maximum, because at higher molding pressures there was considerable extrusion of tin into the die wall, jamming the die plungers. The tin specimens were not -in tered, as this phase of the work was- done merely to see how much a very sold metal could be compressed. The aluminum powder was compressed at various pressures up to 50 lons per sq in. Higher pressures could not be used because of extrusion into the die wall The compacts were sintered one hour at 000 in pure dry hydrogen. The copper powder was molded at vari-ous pressures up to 96 tons per sq. in. One set was sintered at 750°C., another at 050 C. for one hour in pure dry hydrogen. The electrolytic iron powder was molded at various pressures up to 00 tons per sq. in. and sintered, one set at Soo°C and one set at 1300°C for one hour in pure dry hydrogen. Extra 325-mesh specimens were also prepared to study the effect of reduced particle size on grain structure. The brass powder was molded at various pressures up to 96 tolls per sq. in. and silltered for one hour. one set at 65o°C. and one set at 800°C, in pure dry hydrogeu.

Jan 1, 1945