Search Documents

By K. Y. Haramy

This report describes the development of an equation for predicting the crushing strength of 2-inch (5.08-cm) cubes of coal from point load tests made on irregular lumps. The equation was developed from point load and cube crushing strength tests performed on coal samples from six Western U.S. coal seams. For the six coals tested, the means of the point loads [(P)] in kg at failure were approximately proportional to the deans it the distances [(V)], in cm between the platen points for lumps in the 2 to 10-cm size ramie. This finding is at variance with results of tests on other rock types reported in the literature, which tend to show that P is proportional to D2 , as is normally assumed (in theoretical grounds. [The average crushing strength of a 2-inch (5.08 cu) cane for each type of coal was plotted against the log 10 of the slope of the P vs D plots, AP/AID . A straight line was fitted to these plots. The equation of the fitted line is cr = 1.72 x 10 4 10gK -2.10 x 10 4, where Cr is re estimated 2-inch (5. 08-cu,) cube crushing strength of the coal in psi and K is the scope of the straight line fitted to a plat of P v D for the same coal.]

Jan 1, 1982

By Gottlieb P, Sutherland DN

The paper describes a method of making quantitative mineralogical measurements on many of the major lead/zinc orebodies in Australia. The work was done using QEM*SEM. It was found that a relationship betwen phase-specific surface area and particle size, when plotted in a suitable way, gave a straight line with slope related to the grain size of the mineral in question. The method provides an excellent way of differen- tiating between minerals in existing orebodies and, consequently, an easy way to establish a comparison between a new prospect or orezone and current operations.

Jan 1, 1988

By Z. Smieszek, Z. Szota, P. Gajowski

"A new method for measuring the total quantity of suspensions contained in the electrolyte during copper electrorefining has been developed by the Institute of Non-Ferrous Metals, Gliwice. Electrolyte purity, and the suspensions content in particular, is of essential importance for the quality of electrolytic copper produced during the process. Suspensions contribute to the increase of slime impurities in electrolytic copper and increase losses in noble metals. Up to now, the laboratory method has been used for the· process control which provides analytical results with considerable time delay. Therefore, it is useless for the process control.The measuring method developed enables continuous measurements of a suspensions content directly within the stream of the flowing electrolyte. The principle of measurement is based on changes in optic properties of the electrolyte with varying suspensions content.1. IntroductionIn copper electrorefining, it is essential that the final product quality be maintained. If suspensions are present in electrolyte, the content of slime impurities in electrolytic copper, (such as Pb, Ag, Bi, Sn, Sb, and As), increases which can result in the occurrence of the so-called slime dendrites on cathodes, thus debasing the quality of the product. As a normal suspension content in electrolyte, the contents in the order of several mg/l are considered, usually not more than 5-6 mg/l, while contents exceeding 20 mg/l are referred to as an alarm state. Suspensions present in an electrolyte are usually a light fraction of anodic slime whose main components are metallic silver, lead sulphate, complexes of antimony and arsenic, and sometimes even calcium sulphate; they are mainly composed of very small particles of lead sulphate and antimony complexes. Sometimes - - in case of alarm states - - the so-called ""wandering slims"" can be observed, which are composed mainly of arsenic and antimony complexes. These ""wandering slims"" make a serious technological disturbance. In normal operating conditions of the electrorefining plant, an increase of suspension content can result from such reasons as crack of filter cloth in a slime filter, turbulent flow of the electrolyte, anodic passivation, aeration of the electrolyte, and improper servicing of an electrolytic tank. It is necessary to continuously control the suspensions content in electrolyte for proper electrorefining."

Jan 1, 1989

By J. K. Whyatt

Assuring ground control safety in many mining and tunneling projects depends, at least in part, on an understanding of in situ stress conditions that will be encountered. Yet it is rarely practical to conduct more than a very limited number of stress measurements. Stresses along the route of a proposed excavation are typically interpolated from available measurements, often assuming a linear variation of stress with depth (or elevation). However, projects where multiple stress measurements are conducted often report more complex variations of in situ stress, usually in apparent relationship to geologic structures. These structures often include lithologies of contrasting elastic properties. A method is proposed for estimating stresses in these cases by first back-calculating regional loads from available stress measurements and then modeling the distribution of stress throughout the rock mass. The method has been successfully applied to a set of in situ stress measurements from the Coeur d’Alene Mining District of northern Idaho, USA. Results provided new insights into district stress conditions and the distribution of rockburst hazards along mine drifts and between various mines. This success should transfer readily to suitable deep tunneling projects.

By John A. Herbst, Kuang Y. Lee

Coarse particle size measurement is essential for the automatic control of a size reduction process like crushing or SAG milling in order to achieve optimal process performance. However, the on-line size measurement of coarse material is not easily obtained due to the problems of material handling and sample statistics. A technique based on advanced image analysis and quantitative stereology has been successfully developed and tested in a pilot scale setting. The chord length distribution of coarse particles on a moving conveyor was measured with an image analyzer and then transformed to the mesh size distribution with a stereological model and a special numerical method. Some test results as well as the technique's industrial suitability and limitations of this method are also discussed.

Jan 1, 1992

By C. D. Mishra

The recycling potential for any gainful utilisation of the waste products is dictated by their quality, especially the chemical characterisation. The methods commonly used for the analysis of fly ash e.g. wet chemical, AAS, ICP-AES etc are time consuming. The paper describes a rapid XRF-based method for routine analysis of fly ash which involves preparation of local standards, optimisation of sample preparation technique and use of a simple PC-based software to account for interelement effects. The matrix corrected values are found to agree well with the wet chemical data.

Jan 1, 1992

By A. Kalogeropoulos, T. Michalakopoulos

The DEM has been used in several studies to numerically simulate the response of rocks to the cutting action with drag tools. In this research, the aim is to realistically simulate the rock material and the cutting process by controlling the grain interlocking of the numerical assembly and streamlining the calibration process while focusing on the cutting force and the failure mechanism.

Apr 1, 2023

By Christopher Mark

A new method for the design of longwall pillars, called "Analysis of Longwall Pillar Stability" (ALPS), is described. The method is the final result of a research program that included two major field studies, extensive reanalysis of data from other in situ measurements, and detailed evaluations of available pillar design methods. The key problem addressed by ALPS is estimation of the abutment loads applied to longwall pillars. Based on underground stress measurements made in mines in three states, equations for predicting the magnitude, distribution, and time-of-arrival of abutment loads are proposed. Stress measurements are also used to evaluate empirical pillar strength formulas for use in longwall pillar design. ALPS has been verified by application to case histories from several mining areas, and examples taken from the Pittsburgh and the Blue Creek seams are presented. Step-by-step guidelines for using this design method are also given.

Jan 1, 1987

By Nicholas Chlumecky

To date information is somewhat limited concerning the strength and bearing capacity of floor strata, which is of great importance where proper roof control is desired. If the bearing strength of strata is not known, the support may be excessively strong in relation to the support capacity of the floor, with the result that strong props sink into the floor strata, giving them dubious value as a roof support. The method described is used to determine how tests are made on dry rock to determine the required support area for the base of props or other structures which may rest on rock strata in mines. Relationships were established for the bearing capacity of rocks which were subjected to loads by means of bearing areas of various sizes ranging from 0.09 sq cm (.014 sq in.) to 700 sq cm (108.5 sq in.). This permits the evaluation of the bearing capacity of rocks by testing small areas for the de- termination of the capacity of larger areas.

Jan 3, 1968

By Madgwick J

A novel method for determining viable cells of the mineral leaching bacterium Thiobacillus ferrooxidans has been developed. The cells were collected on 0.45/Lm cellulose acetate filters, washed with artificial minewater, and incubated in the presence of ferrous ion at pH3 in an atmosphere containing radioactive (14C) carbon dioxide. Colonies of bacterial growth were detected by the image formed on X-ray photographic paper (autoradiography). The method was compared with three conventional techniques and shown to detect three orders of magnitude more cells in cultures of Thiobacillus ferrooxidans in the late exponential phase of growth.

Jan 1, 1987

By John W. Bell

A FEW years ago the writer had the privilege of examining a piece of apparatus in the Forest Products Laboratory of McGill University which engaged his attention. The Forest Products Laboratory has an excellent installation of wood-grinding machinery, and the officials in charge were naturally interested in acquiring means for estimating the fineness of various wood grinds. The problem was referred to Dr. O. Maass ( l ). Dr. Maass designed a piece of equipment to measure the surface of a wood grind and derived an equation applicable in calculating its value, as follows : After inspecting this apparatus, the writer was disposed to believe that, with some modifications, Dr. Maass' ingenious idea might be utilized to measure the surface of mineral powders. Obviously, some difficulty would be found in maintaining an even suspension of mineral particles of high specific gravity compared to that of wood pulp. The writer will not bore the reader with a description of the various machines built and tried out. Some of these were satisfactory enough to obtain some valuable information, and to bring to light a difficulty which threatened to bring the investigation to an abrupt ending. For the mineral quartz, it was found that Kin the formula above stated was not a constant.

Jan 1, 1944

By Madgwick J. C, Ralph B. J

A method for the determination of microgram quantities of uranium in leachates from low grade uranium ores is described. Solubilized manium is purified by transfer to an organic solvent by a selective solvent extractionprocedure using tributyl phosphate, iso-octane, and aluminium nitrate. The organic phase is mixed with scintillation fiuors in toluene and the radioactive decay determined in a liquid scintillation counter. The method is sensitive and reproducible in the range 3-30 µg uranium.

Jan 1, 1978

By Briggs H.

The illustrated device uses the principle that the lamp can burn with a smaller inlet passage if the air is rich in O2 and that the size of the inlet can be made a measure of O2 percentage. The appliance consists of an adjustable cut-off applied to the inlet of a safety lamp of the improved Gray pattern. Precision is assessed from tables of calibration tests in air contaminated with blackdamp of CO2:N2 composiiton 1:5.67 at temperatures of 40-70 degrees F. Results are presented of tests at St. Germain's colliery, of tests in air contaminated with pure CO2 and of air contaminated with both blackdamp and inflammable gas; published ranges in mine-air blackdamp compositions are tabulated as ranging from 90.06% N2 to 43.90% CO2. When firedamp is present at 1.25-2.5%, its content must first be estimated by means of the cap and a fifth of its value then deducted from the lamp reading for O2

Dec 1, 1916

By Stephen P. Signer

A method to assist in the evaluation and selection of roof bolts using in situ measurements of roof bolt loading has been developed by researchers of the Spokane Research Center, National Institute of Occupational Safety and Health. Both axial and bending forces are measured by strain gauges at many locations along the length of fully grouted bolts during various stages of mining. This information is then used to ( I) predict bolt loading for variations in bolt spacing, grade, and diameter, (2) calculate the design changes necessary in zones where bending loads are high, and (3) determine if bolt length is adequate. Results from several case studies of full-column bolt loading in coal mine gate roads are used to illustrate the design method. This knowledge will give design engineers a tool for the selection of roof support systems that will improve underground safety by reducing roof bolt failures.

Jan 1, 1997

By Philip W. Johnson, Charles D. Haynes

"Abstract - The coalbed methane industry has become a prominent source of domestic natural gas, with its technology having evolved over the past 30 years. Whereas most coalbed methane wells are able to produce without major interruption over their economic lives, wells operating in an underground mining area are subject to being mined-through. If mine-through occurs, the productivity of the well is at least compromised, and may even be terminated. The economic consequences of mine-through may be relatively simple if mineral ownership and extraction rights are common for the coal and coalbed methane. However, if ownership is not common and a superior coalbed methane lease exists, the coalbed methane ownership must be compensated for lost production caused by mine-through. This paper presents a relatively straightforward method to calculate the value of the lost production caused by the mine-through. It uses technology from mining and petroleum engineering, as well as simple economics and financial management techniques.Sommaire - L’industrie de la production de méthane houiller est aujourd’hui une source importante de gaz naturel domestique dont la technologie a considérablement évolué au cours des trente dernières années. Bien que la plupart des puits de méthane houiller peuvent être mis en production durant l’entièreté de leur vie utile sans interruption majeure, les puits implantés en périphérie de mines souterraines sont sujets à être recoupés par ces dernières. Un tel recoupement peut compromettre, ou même mettre fin à la production d'un tel puits. Les conséquences économiques du recoupement par une mine souterraine peuvent être relativement simples quand les droits miniers et les droits d’extraction sont détenus en commun pour le charbon et le méthane houiller. Si toutefois ces droits ne sont pas détenus en commun et qu’il y a eu octroi d’une concession de méthane houiller de qualité supérieure, les détenteurs du méthane houiller doivent être compensés pour la perte de production résultant du recoupement par une mine souterraine. Cet article présente une méthode relativement simple pour calculer la valeur des pertes de production suite au recoupement par une mine souterraine. Cette méthode fait appel aux technologies de l’industrie minière et pétrolière ainsi qu’à des techniques simples d’économie et de gestion financière."

Jan 1, 2006

By Bigdy D. N

The paper describes a system for providing mine management with a continuous indication of the effectivness of longwall coalface powered supports in controlling roof-to-floor convergence. The system comprises on-face instrumentation monitoring convergence and support leg circuit pressures, a means of transmitting the output of that instrumentation to the surface for collection, and software which presents both a condensed analysis for rapid review of the current state, and extended analyses from which remedial action can be recommended if a problem is identified. The results of a field trial are presented showing that meaningful results can be obtained.

Jan 1, 1988

By D Burgess

Since the days of mandatory high cost pilot plant testing in 6 ft + 2 ft SAG mills autogenous griding/semi-autogenous grinding (AG/SAG), mill specific energy is now calculated by various empirical formulae and pilot testing carried out in small laboratory mills. Barratt (1989) described a method using Bond Indices than adding a single factor of 1.25 to arrive at the AG/SAG specific energy. In 1991 the Canadians developed the SAGPower Index (SPI), test using 2 kg of material in a 300 mm diameter mill. This test has been further developed by Starkey, Hindstrom and Orser (2006). This test now includes a Bond Ball mill work index test.The Macpherson test is still being offered by some testing facilities. This dry test requires at least 180 kg of material.Morrell (2004) formulated an AG/SAG specific energy generator based on a drop weight index Value (DWi). This DWi value is related to the Ab parameter and the material specific gravity. Morrell reconfigured the BondÆs Third Theory formula to cause extra power requirements to be inputed. This technique incorporates the material specific gravity (SG). The AG/SAG specific energy values produced using this method are susceptible to higher values of crushing and rod mill work indices.This paper offered describes a more simple method to generate AG/SAG specific energies. This programme incorporates Bond work indices, the JKMRC parameter Ab measuring impact breakage and the parameter ta measuring the abrasion rate, then employs a series of efficiency values nominated for each transition size (AG/SAG T80). These efficiency values have been compiled over the years from actual operating plants and documented reports.CITATION:Burgess, D, 2012. A method of calculating autogenous/semi-autogenous grinding mill specific energies using a combination of bond work indices and Julius Kruttschnitt parameters, then applying efficiency factors, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 37-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By J. B. DILWORTA

Ix estimating the investment-value of a mining-property or plant, the value of which decreases with operation, it is often necessary to know the sum which must be set aside periodically from earnings either to renew the plant at the end off its life, or to return the capital involved when the earning-power of the investment has ceased. In such cases it is manifestly incorrect simply to divide the total amount to be retired by the number of periods (usually years) during which the investment shall be active, as the sums periodically withdrawn have a certain interest-earning power varying with the length of time they are held and with the opportunities afforded for their investment. But though the interest may be considered to accumulate regularly year by year, yet the rules and tables for compound interest do not apply, owing to the addition of a fixed amount of new money to the total at the beginning of each period. Briefly stated, the problem of sinking-funds is, to find the amount of money which must be periodically set aside at a certain rate of interest, regularly compounded, to yield a certain sum in a given, length of time. In most practical cases the interest is compounded and the fresh amount added at the same time-usually once a year-and on this basis the problem may be solved as follows

Nov 1, 1909

By Frank Firmstone

Discussion of the paper of John B. Dilworth, presented at the Pittsburg meeting, March, 1910, and printed in Bulletin No. 35, November, 1909, pp. 1041 to 1043. FRANK FIRMSTONE, Easton, Pa. (communication to the Secretary*) :-Mr. Dilworth's formulas and tables are of course correct, and the extinction will occur as calculated, provided the money periodically set aside for sinking-fund be really invested. and the interest compounded as assumed in the calculation. Actually, in almost all cases, such funds are used "in the business," in which case, in addition to the periodical charges for principal of the fund, additional charges must be made at the end of each period to cover the interest and compound interest on previous charges. The periodical charge for sinking-fund thus becomes a varying and continually increasing one until the date of extinction. On many accounts it seems more natural and convenient to make the extinction by a fixed periodical charge under the legal rule for partial payments, namely, that each payment should apply first to the interest due at the date of payment;: and any remainder, after this is satisfied, be deducted from the principal before the interest for the next period is calculated. The formula below is convenient for such calculations S, Principal to be extinguished. Q, Periodical payment or charge for sinking-fund. B, Balance unpaid at date of nth payment, but before that payment is made. r, Rate of interest per period per cent. n, Number of payments or periods. Then, B=S(1+r)n-Q(1+ r)n-(1+r) Received July 27, 1910.

Apr 1, 1911

By Pierre Mousset-Jones, Felipe Calizaya

The design of an auxiliary ventilation system for long underground openings (drifts, ramps and shafts), often requires the installation of multiple fans. The fans are installed in series and separated from each other by rigid ducts of fixed or variable length. However, problems relating to excessive leakage often occur, with each project representing a unique problem requiring an efficient solution. In this study, a method to determine the design parameters of an auxiliary ventilation system is presented. The method is based on the principle of partitioning a long ductwork into segments of finite length and solving the resulting networks separately. Specifically, the method is developed to solve two types of problems: constant fan spacing, and constant fan size. In the former, the fan spacing is fixed, and the problem is solved for fan sizes. In the latter, the problem is to solve for fan spacing. An example is used to illustrate the method.

Jan 1, 1993