Search Documents

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of rgrinding conditions on galena flotation and galena separation from pyrite. The various reactions occurring on the mineral surface were investigated by a range of techniques, including OH- addition to maintain the grinding pH, EDTA extraction, XPS and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the metal oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite but had little effect on galena. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled."

Jan 1, 2003

By Sakai Kunito, Nigel B. Sugden

If an Earth Pressure Balance (EPB) TBM is operated effectively tunneling can be carried out producing negligible ground movements. Using the methods given in this paper face losses of the order of 0.5% and less are generally obtainable using an EPB. Operating the EPB TBM in this manner reduces the requirement for the building protection measures used to protect surface structures. This can result in a considerable cost saving for the construction of a tunnel under built up areas. This paper to give guidance on the causes of ground movements around a TBM and the methods of running an EPB TBM that will minimize those movements. Details of how this was successfully done during the construction of the Bangkok Metro are given. The paper is split into three parts as below. 1.Causes of ground movements due to TBM tunneling 2.Methods of controlling those movements using an EPB TBM 3.Case history Bangkok Metro (water main)

Jan 1, 2001

By Alday B. Andrews

A computer program called Seiswise that predicts the character and intensity of ground vibration generated by surface blasting operations was developed and field tested. The program uses the time histories of one or more pilot shots in combination with various initiation sequences to construct synthetic seismograms which are examined to select designs that will produce low levels of ground vibration.

Jan 1, 1990

By Hideki Shimando

Periodic weighting and windblast which are caused by the dynamic effects of overburden in a longwall panel significantly affect longwall mining This study describes past experience with wind blast at Miike Colliery, proposes a new loosening system using hydraulic fracturing and moistening, and also discusses strength deterioration in hard-to-collapse roof rocks due to water in order to solve the problems caused by the effects of dynamic roof rocks behavior in a longwall face

Jan 1, 1998

By Hamid Maleki

Mine seismicity is influenced by the mechanical properties of both near-seam strata and overburden/underburden and the prudent selection of mining methods and mine layout designs, utilizing sitespecific structural setting of the mines. The importance of adequate data collection, monitoring, and prudent structural designs has long been recognized and utilized in many U.S. operations with adequate engineering resources. In this paper, two case studies of historic seismic events and contributing factors, in deep coal and trona mines with overburden thickness exceeding 1,500 ft, are reviewed using observations and analysis. By back analyzing the overburden response in a historic room-and-pillar coal mine, the overburden collapse mechanism associated with a 3.3 magnitude seismic event is reviewed as well as the need for improvements in designs including panel and barrier pillar widths. Similar high-order seismic events were also experienced in trona mines of the Green River Basin during 1990s, interrupting room-and-pillar mining and creating ground control concerns. Efforts to improve structural mine designs are described in this paper leading to stable and productive operations for decades following the high-order seismic events in both coal and trona case studies. These efforts included improving room-and-pillar extraction layouts and utilizing properly designed longwall mining techniques that were verified using long-term geotechnical instrumentation. The study mines are located on the Wasatch Plateau (WP), Utah and in the Green River Basin (GRB), Wyoming. More recently, in Utah’s East Mountain alone, Energy West Mining Company (EWMC) has extracted some 165 million tons of coal without any significant incidents. Overall, favorable geologic conditions and prudent mine layout designs are key elements to this successful experience in both single- and two-seam layouts. Utilization of conservatively designed longwall mining technique in the GRB has been geotechnically stable, using reported experience in 15 panels and monitoring results in the Northwest (NW) District with measurable longwallinduced seismicity being rare. These studies demonstrate a considerable amount of progress that has been made within the last four decades in the application of longwall mining technique, integrated monitoring, and analyses for the verification of structural designs in mines in the United States.

Jul 1, 2023

By P Cavieres, R Dunlop, S Gaete

El Teniente Mine started the exploitation of the primary rock in the beginning of the 1980s decade, using caving methods. Since the beginning the mining activities have induced seismicity including some occasional rockbursts. Owing to the relevant damages, the mining operations were stopped in some production sectors. This paper describes the concepts that have been used in order to control the induced seismicity based on the strategies for controlling the rockmass breaking process, which depend on mining parameters. It also presents the main concepts applied in the Teniente Sub6 sector design and the experience collected during its sector exploitation.

Jan 1, 2000

By M. J. Gula, S. S. Xue, E. P. Horwitz, J. T. Harvey

A study was conducted to control iron in copper electrolyte streams using Eichrom Industries' new monophosphonic/sulphonic acid resin. The resin strongly and selectively extracts ferric ion over copper and cobalt from highly acidic copper electrolytes. The resin has a loading capacity of 27-g/L iron and can be readily regenerated. In addition, the new resin can easily be synthesized using commercially available starting materials. This paper presents the experimental results for iron control in copper electrolyte streams using the new resin and discusses its potential applications to other hydrometallurgical streams.

Jan 1, 2002

By M. J. Gula, S. S. Xue, E. P. Horwitz, J. T. Harvey

A study has been conducted to control iron in copper electrolyte streams using Eichrom Industries’s new Monophosphonic /sulphonic acid resin. The resin strongly and selectively extracts ferric ion over copper and cobalt from highly acidic copper electrolytes. The resin has a loading capacity of 27 g/L of iron and can be readily regenerated. In addition, the new resin can be easily synthesized using commercially available starting materials. This paper presents the experimental results for iron control in copper electrolyte streams using the new resin and discusses its potential applications to other hydro-metallurgical streams.

Jan 1, 2000

By S. Shairp

The first commercial application of the Dynatec two-stage zinc pressure leach process commenced operation at the metallurgical complex of Hudson Bay Mining and Smelting Co., Limited in Flin Flon, Manitoba in 1993. A key feature of the successful leaching operation is the presence of iron in solution, which facilitates oxygen transfer in the autoclaves and enables rapid oxidation of zinc sulphide minerals. At the same time, the solution from which zinc is recovered must be essentially iron free. Precipitation of iron from the solution starts in the autoclaves and is completed in subsequent atmospheric purification steps. Conveniently, these iron precipitation steps also remove nuisance elements such as arsenic and fluoride from the solution, while producing solids with good liquid-solid separation characteristics. This paper provides an overview of the current operations in Flin Flon, with particular reference to the behaviour and deportment of iron throughout the zinc plant.

Jan 1, 2006

By M. H. Pettibone

During the past decade, the size of grin- ding mills has steadily increased. Mills 11 m in diameter with 9 mW motors have been installed with even larger units on the drawing board. The rising costs of energy and labor have spurred interest in improving efficiency while reducing capital investment and operating labor. Autogenous and semiautogenous grinding have experienced renewed interest as efforts to reduce operating and capital costs have increased.

Jan 1, 1981

By Nozomu Hasegawa

The phase diagrams and microstructures of the slags in the Mitsubishi Continuous Copper Smelting and Converting Process were studied for the prevention of the magnetite troubles such as accretion build-up on furnace hearths and launders, blockages at the melt outlet, slag viscosity increases and so on. According to the results of those studies, the silica and lime contents in the silicate slag at the smelting furnace, and the lime content in the lime-ferrite slag at the converting furnace were changed, resulting in lower and more consistent copper levels in the discard slag, with much less need for operators to clean melt outlets and launders. However, these changes may decrease the desirable amount of accretion-coating inside the furnaces and thereby reduce furnace campaign lives. Therefore, a method of estimating the magnetite level in the melts was developed, and slag compositions and temperatures have been controlled within the appropriate ranges to prolong furnace lives and also prevent magnetite troubles.

Jan 1, 2003

By Pengfu Tan

Converter slag chemistry control has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter has been developed to predict the behavior of magnetite in the converter slag. Predictions of bath temperature, slag and matte compositions, and magnetite content in the slag have been validated by industrial data. The effects of fluxing strategy, returns and skim charges, oxygen enrichment, and temperature on the magnetite formation in the slag have been predicted and discussed. Some improvements of the industrial operations have been presented.

Jan 1, 2005

By Bratt G. C

When zinc is electrowon from concentrates or residues of high manganese content, the zinc sulphate electrolyte may contain high levels of manganese. The manganese level is usually controlled by removal of manganese at the anode as the dioxide during the zinc electrodeposition stage.By increasing the temperature of an electrolyte containing 8 gll manganese from 35°C to 90°C, decreasing the acidity from 100 gll to 30 gll, reducing the current density from 432.A.m-2 t6 286 A.m-2 and using new lead anodes containing over 0·75 per cent silver, the current efficiency for manganese dioxide removal was .increased from less than 1 per cent to over 20 per cent.At the same time the current efficiency for zinc deposition was maintained above 90 per cent by additions of high molecular weight cationic polyacrylamides to the cell. By utilization of these conditions in a small number of cells, the manganese level in the circuit could be economically concrolled to any desired level.With these conditions the formation of the dioxide changes from an indirect route, via Mn04-, to a direct oxidation of Mn2+ to Mn02.The incorporation of impurities such as Pb, K, NH4, Cu, Ni, or Fe makes the deposit unsatisfactory for direct use in Zn - Mn02 dry cells. The deposit structure changes from cryptomelane at low temperature to y3-Mn02 at high temperature.

Jan 1, 1975

By T. C. Murray

An automatic control system was recently installed to insure the continuity of operation between the ship docking and ore handling facilities and the computerized conveyor-fed sintering plants and blast furnaces. Although the basic concept for material handling has not changed, many innovations including computer control have been implemented.

Jan 1, 1978

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

By D. W. Evans

Mine subsidence problems due to coal extraction have occurred in a number of areas throughout the United States. Depending on the local geology, the depth of the mined seam, the type of mining method employed for extraction, and other related factors, subsidence can result in anywhere from slight displacements to a total loss of ground. These conditions can have serious consequences on the health and safety of the people living above the mined areas. A number of methods exist to provide support for the ground overlying mines. All of these methods employ some mechanism for providing additional support to either the roof of the mine or the sides of the pillars. Since failure usually occurs due to overburden stresses which are transmitted to the roof and pillars, these methods employ techniques to counteract stresses induced due to the coal extraction. The applicability of any particular method will depend on the availability of backfill material, the areal extent of the affected area, and of course, the cost. The primary use of coal ash for subsidence control has been as a backfill material for the stabilization of large areas. Large scale backfilling projects for subsidence control have been performed in Rock Springs, Wyoming, Wilkes-Barre and Scranton, Pennsylvania, and in Fairmont, West Virginia. Some of these projects have utilized sand, as well as, coal ash as backfill material. Much of the backfilling work performed in the United States has been done in an effort to control mine subsidence in abandoned mines. South Africa, on the other hand, has used backfilling extensively both for ash disposal and to increase extraction in active mines. The utilization of repetitive fill and mine techniques has resulted in extraction increases of as much as eight percent in shallow mines and as much as twelve percent in deep mines.(1) The coal ash injection system which can be used for backfilling depends largely upon whether the mine voids are dry or submerged. For dry mines, hydraulic or pneumatic conveyance systems can be used, while submerged mines are limited to backfilling by hydraulic methods. The use of coal ash as a backfill material has a number of advantages, such as: 1. Coal ash is available in areas throughout the United States and in many instances is conveniently located near areas requiring backfilling. 2. Coal ash is available in significant quantities since many coals when burned will result in about 15 to 30 percent ash by weight. 3. Coal ash as backfill is, in many instances, the most economical alternative fill material. Due to the costs associated with above ground disposal, power companies will often times give the material away to lower their overall operating expenses. 4. Coal ash is usually pozzolanic in nature, that is, this material results in cementitious bonding within the backfilled matrix of material.

Jan 1, 1982

By Brian Flintoff

Basic process control is an integral part of most mineral processing plants. It is widely acknowledged to have helped many operations reduce costs and increase productivity and performance. The research community is very active in the development and evaluation of both model based and Al techniques for advanced control applications. Vendors and specialist consulting or engineering firms are in business to help deliver these solutions to the plant floor. It would seem that there is a good balance between business needs and technology, and that the industry should be moving steadily forward in an aggressive pursuit of plant-wide automation. However on closer examination one sees some systemic problems which are sewing to inhibit progress. One of the mist obvious manifestations is the gap which exists between the available technology and current This paper explores the control of mineral processing systems, with a particular emphasis on some of these problem areas.

Jan 1, 1995

By D Gelling

Mineral sands dry plants consist of a large number of repetitive unit operations with significant transport delays, in the form of stream pipes, conveyors and elevators. As part of the P255 mineral sands sponsorship and using the JKMRC developed conductor/non-conductor (CNC) gauges, control loops have been implemented at the multi-duty dry plant of Cable Sands Limited at Bunbury. This paper describes the loops for kV control on a rougher high tension roll machines (HTR). The options available are product grade control and ratio control using the JKMRC CNC gauges, which measure the percent conductors in a stream. The purpose of control is to stabilise the circuit operation against disturbances such as atmospheric and feed disturbances.

Jan 1, 2001

By Ira B. Jorafemon

In the interesting Institute symposium of the preservation of peace by force, through mineral control, one important aspect of the question was not presented. This is the responsibility the United Nations, and particularly the United States, will incur the through limitation of the economic activities of nations that are now friendly to us, as well as of nations that are enemies or are under the control of enemies. After the war all nations, friends as well as enemies will be poor. Hunger and bankruptcy will, will like the sword of Damocles, hang over the heads of all of us on this blundering planet. When the actual fighting is over, there will be a universal attempt to squirm out from under the sword by resuming production of peacetime goods, for trade as well as immediate consumption.

Jan 1, 1944