Search Documents

Conventional treatment of oxide and oxidised sulphide minerals by flotation involves the use of sodium sulphide for sulphidisation. Sodium sulphide is generally applied in a "slug" dosing fashion with manual regulation. However, it is recognised that "over addition" or "under addition" of sulphidising reagent can result in poor flotation recoveries. Thus, control of sodium sulphide additions is an important aspect of a sulphidisation circuit, both commercially and metallurgically. In any plant where the flotation feed is "constant" it is possible to operate at a constant rate of addition of sodium sulphide. In actual plant practice, however, it is difficult to maintain a truly constant feed for any reasonable duration because this implies not only a constant feed-rate, but also constant mineral composition and particle size range. These factors can vary significantly and ideally require corresponding variations in the additions of sodium sulphide to maintain optimum recoveries. To cope with variations in the feed, it is essential to have automatic rather than manual regulation of the sulphide reagent addition. The CPS process achieves this control by utilising a sulphide ion-selective electrode as a control instrument in sulphidisation. The CPS process which uses a selective electrode, enables the sulphide ion concentration in the flotation pulp to be monitored and controlled continuously throughout the stage of sulphidisation.

Jan 1, 1989

By Y. Wang

In this study, homogeneous (unseeded) precipitation of nesquehonite (MgCO3.3H20) by the reaction of MgC12 with (NH4)2CO3 in supersaturated solutions at 30 °C was investigated. Factors which influence the precipitation of MgCO3.3H20, such as initial concentration, temperature, stirring speed, titration speed, equilibration time, have been studied. SEM images show that the initial concentration and titration speed have significant effect on nesquehonite's crystal morphology and particle size. In addition, stirring speed and equilibration time also have some influence on its properties. With the optimization of operating conditions, the crystals can grow up to a length of about 40µm and a width of 5µm, indicating good filtration properties. High purity nesquehonite obtained in this study was calcined to produce highly pure MgO at 800 °C as shown by XRD results. The novel process may be used to separate Mg and Li from high Mg/Li ratio brines in Qinghai, China.

Jan 1, 2007

By Afrodite Ntziouni, Vassilia Kasselouri – Rigopoulou, Athanasia Kyritsi, Konstantinos N. Pistiolas, Stamatia Gavela, Konstantinos Kordatos, Lazaros Iliadis

"The present study deals with the production and characterization of rice husk ash (RHA) and its use in the synthesis of zeolite of type ZSM-5. Rice husk was combusted in various temperatures with aim to find the suitable conditions for the production of amorphous silica. The resulted amorphous silica ash was then utilized as a starting material for the synthesis of ZSM-5 zeolite using the low temperature and atmospheric pressure process. The method led successfully to the synthesis of highly siliceous zeolite of type ZSM-5. The produced material was characterized using x-ray diffraction (XRD) and scanning electron microscopy (SEM).IntroductionRice husk is a major by-product of the rice-milling industries and it is usually used as a fuel for steam generation due to its high calorific power. During its combustion, rice husk ash (RHA) is produced. Knowing that the annual rice world production is over 615 million tons (2005), thus resulting in a potential production of more than 22 million tons of RHA [1], it can be understood that the RHA disposal is a crucial issue towards the environmental protection. However, due to the high silica content, RHA can be used as an alternative cheap source of silica for many uses, including as filler in polymers [2], concrete [3] and synthesis of zeolites [4-7].The burning of rice husk in air results in the formation of RHA with content in SiO2 that varies from 87 to 97% depending on the burning conditions, the rice variety, the climate and the geographic area [8]. Some small amounts of inorganic impurities are always present in the ash along with unburned carbon. The unburned carbon can be removed from the ash by further heating treatments in high temperatures, but this usually leads to the crystallization of the amorphous silica to cristobalite and/or tridymite [9]. The crystallization of the contained silica of the ash is also occurred when the burning conditions of husk are uncontrolled [10]. This crystallization is a disadvantage towards the preparation of silicon based materials, because the silica ash is rendered inactive in its crystalline form [11]."

Jan 1, 2008

By S Bluhm, LádeáOliveira, R Funnell

Taquari Vasouras potash mine (Vale Fertilizantes) has many interesting features including virgin rock temperatures of 50¦C at depths of 700 m. The mine has a relatively small shaft system with limited ventilation carrying capacity, which was not adequate to exploit the full extent of the deposit. This limitation was overcome by installing two large-scale recirculation systems with underground reconditioning centres. This paper describes this unique mine ventilation and cooling system and some of its history over the past two decades. The two controlled recirculation systems have been operating safely for some ten years and the use of large-scale recirculation has been a fundamental component in the increase of production and extending the mining further-and-further from the shaft centre. The recirculation systems have played a huge role in the mine profitability and comprehensively extending the mine life. The paper also discusses a number of novel design and operating features such as reverse running pumps for energy recovery. The underground chilled water system design required a number of special safety features in order to minimise the risk of water leakage since this could be catastrophic in a potash mine. This paper describes a good example of a mine in which the final ventilation and cooling system design ends up very different to what was envisaged at the greenfields stage.CITATION:Bluhm, S, Funnell, R and de Oliveira, L, 2013. Controlled recirculation and refrigeration at ValeÆs Taquari Potash Mine, in Proceedings The Australian Mine Ventilation Conference , pp 237-248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By LeEtta M. Shaffner, John R. Marks

The Homestake Gold Mine in Lead, South Dakota, commenced operations in 1876. As is the case with old, deep, continuously developing mines, a ventilation improvement is periodically required to maintain acceptable underground environmental conditions. Recent historical improvements at Homestake include a 5.2m diameter air shaft driven in the 1960's and a 2.1 MWR (580 ton) chilled water plant installed in 1978. By 1983, it became apparent that yet another ventilation upgrade would be needed to keep pace with accelerated development in the deepest mining sections. A study was therefore undertaken to project ventilation requirements for the next ten years and to select the method(s) most suitable to meet those requirements. The study called for a two-phase approach in which air flow and air conditioning were carefully balanced. Phase I, the installation of a new 2240 kW surface fan and several underground circuit changes, was completed in 1986. This paper describes Phase 11: the planning, design, installation and initial performance of the air-conditioning portion of the upgrade.

Jan 1, 1989

Controlled recirculation of nine ventila- tion air is becoming an acceptable practice world-wide. A brief review of operating and planned schemes is given which illustrates the various purposes for using controlled recircu- lation in different types of mines. A de- tailed description is given of the operating and proposed schemes on South African gold mines. This is followed by a description of some theoretical and experimental work which has recently been carried out into certain important aspects of controlled recircula- tion. This includes: safety systems, dust filtration, blast contaminant removal, radia- tion hazards and the development of an expert computer program for the design of controlled recirculation systems.

Jan 1, 1988

By David M. Mchaina, Allan E. Hall, W. C. H. Kruining, Alan Coode, Stephen Hardcastle

This paper details an investigation into the feasibility of recirculating mine exhaust air in Saskatchewan potash mines. This project was initiated following a previous study at Ruttan Mine, Manitoba, which indicated that recirculation of exhaust air to reduce winter heating costs was feasible. The potash industry was selected for study because the mines use a minimum of blasting in their production methods and the exhaust temperature is significantly higher than that of most metal mines. These factors simplify the monitoring system required and have the potential for greater waste heat recovery. A series of measurements of underground mine pollutants was made at the main exhaust and intake shafts in order to determine the feasibility of introducing controlled recirculation of exhaust air. An experimental recirculation circuit was created by opening two existing doors situated between the return and intake shafts. During this recirculation trial, the air quality parameters at the intake, mixed intake and exhaust measuring stations were monitored. The results obtained from a questionnaire circulated to the regulatory agency and the major potash producers together with results obtained from underground field studies at Central Canada Potash (CCP) Division of Noranda Minerals indicated that controlled recirculation of mine exhaust air has potential application in these mines either to reduce heating costs and/ or to increase the face air quantities. A recirculation system is to be designed in conjunction with CCP and the Saskatchewan Ministry of Labour, Mine Safety Unit to attempt to implement a working recirculation system for CCP.

Jan 1, 1989

By Allan E. Hall, Stephen G. Hardcastle, Lucien D. Nel, Jean-Paul Saindon

A description is given of the investigation conducted at Sherritt Gordon's Ruttan Operation in Manitoba during 1986. Gas and dust concentrations were measured in the exhaust air of the major working sections to assess the potential for recirculating exhaust air into the intake air in winter to reduce heating costs. The results indicate that there is excellent potential to significantly reduce winter heating costs by controlled recirculation of exhaust air. Gas and dust concentrations vary significantly during the working shifts but have consistent trends from shift to shift and day to day. The variations in gas concentrations have similar trends but no single gas could be reliably used to predict the variation of the other gas or the dust concentrations. Dilution and the other effects which reduce pollutant levels as the exhaust air returns to surface indicate that recirculation should take place as close to surface as possible, subject to the economic constraints of the airway construction required and the extra fan energy required for the longer recirculation path. Recommendations are made for the choice and positioning of air and dust monitoring sensors and the logic of a control system. Economic analysis of the results indicates that controlled recirculation is viable at an existing mine with a pay back period of approximately two years. Incorporation of a system into a new mine at the planning stage would significantly shorten the pay back period.

Jan 1, 1987

By Ron Robinson, Trevor Harrison

The planning, installation and commissioning of the first scheme of controlled recirculation of air flow in a section of coal mine in Great Britain is described, together with the proposals for a second installation. The work updates a previous paper (Robinson and Harrison, l986) on the subject. The special problems of ventilating the increasingly distant faces of the undersea mines in the North East Area of the British Coal Corporation are discussed and the alternative solutions stated. The advantages of using a system of controlled recirculation of air are proposed together with the safety features considered necessary. Design and installation details of the recirculation fans and a new booster fan are described.

Jan 1, 1987

By C. F. Meyer

The recirculation of mine air in an underground colliery, has always been regarded as a hazardous practice in South African collieries. The Mines and Works Act and Regulations states that fresh air, flowing Into an underground section, must flow out directly into the return airways after being utilized once in the section. One of the largest producing underground collieries in South Africa, Initiated a project on controlled recirculation with the permission of the South African Government Mining Engineer. The project involves the recirculation of 65 m3/s of air inside a ventilation district which serves a total of six production areas. The aim of the project was to increase the airflow to the sections without altering the existing ventilation system. Tracer gas studies were carried out to determine the actual distribution of the recirculated air to the individual areas. The results showed that an effective 54,18 m3/s of the recirculated 65 m3/s reaches the sections. This gives an air utilization figure of 83,4 per cent. Dust surveys were also carried out as part of the project to determine the effect of the recirculation of the return air on airborne dust levels. The results showed that the dust levels remained constant in the main intake and return airways and that no hazardous situation was being created. The project proved to be successful and showed that controlled recirculation can be executed and used as a solution for the supply of air to sections without endangering any lives.

Jan 1, 1993

By Andrew B. Cecala, Robert J. Timko, Christopher J. Pritchard

As mine venti1ation systems become more complex, it is increasingly difficult to supply fresh air to the working face. A high percentage of the fresh air entering a mine never reaches the working face because it short circuits through stoppings and doors, exiting the mine without being utilized. When ventilation limits are reached, the only option presently available to most U.S. mines is to sink a new shaft - an extremely expensive undertaking that many companies cannot afford. Reusing or recirculating a percentage of ventilating airflow may make it possible for some mines to remain operational while maintaining a safe environment for workers. Such a study was performed at a trona mine in Granger. Wyoming. A vane axial fan was used to recirculate approximately 9.4 m /s (20,000 cfm), 25% of the total ventilating airflow, back to the working face area of a three-entry continuous miner section. This study involved two evaluations: the first when the face was 305m (1,000 ft) from the recirculation fan, the second when the face was 610m (2,000 ft) from the fan. The evaluation consisted of monitoring the mine atmosphere for respirable dust, methane (CH4). carbon monoxide (CO), and nitric oxide (NO), at various locations in the intake and return entries. Several shifts were monitored, with and without the recirculation system in operation. With the recirculation system in operation. there was an increase in measured respirable dust concentrations in the intake along with a slight increase in the mine temperature (1.67°C). There were also some minor changes in CO and NO levels in the intake entry, but this seemed to depend on the proximity of the instruments to the turn-around point for the diesel haulage vehicles, than to whether the recirculation system was or was not in use.

Jan 1, 1989

By Tuck M. A

The increasing depth, mechanisation and distance of working areas from surface connections places an ever greater contaminant burden on ventilation airflows. Some British Coal mines are already experiencing significant problems in providing adequate climatic conditions in the working areas and have had to introduce air conditioning. Previous work has shown that in mines of low to moderate virgin strata temperature the application of controlled district recirculation could serve to improve climatic conditions at the working area.

Jan 1, 1988

By A. A. Sobek

Controlled release systems delivering the required concentration of an effective bactericide over an extended time period have been developed by The BFGoodrich Company's ProMac® Systems group. The ProMac system is site-specific and includes a four-step approach to controlling acid mine drainage (AMD): (1) Diagnosing the problem, (2) Prescribing the treatment, (3) Supervising the application of controlled release bactericides, and (4) Honitoring the success of applied treatment. The success of the ProMac system is evidenced by improved water quality, healthy vegetation, a reduction in levels of acidophilic thiobacillus, and a corresponding increase in population of beneficial microorganisms.

Jan 1, 1986

By Greg Rappard, Francois Holowenczak, James Rickard

The King George V (KGV) Shaft forms part of MTR Corporation Limited (MTRCL) Works Contract 703 extension of the underground West Island Line on Hong Kong Island. The Shaft and the associated adit was the sole access to excavate the running tunnels. Originally during the Detailed Design stage, it was concluded that blasting was not feasible at the KGV Shaft due to the close proximity of sensitive receivers in the form of residential buildings, electrical cables and hospitals. As a result, the Contractor planned to excavate the Shaft using mechanical means with a programme time of seven months. The Contractor appointed a Sub-contractor to analyse the feasibility of excavating the Shaft by blasting. The Sub-contractor reviewed the proposal and recommended the use of an innovative blasting technique that had never been previously employed in Hong Kong. The Sub-contractor recommended the Shaft be blasted using DetNet electronic delay detonator technology, manufactured by AEL Mining Services in South Africa, with an initial 1.5m depth of water ballast covering the blast face. The electronic delay detonators provided initiation accuracy to ensure there would be no overlap between sequentially detonating blastholes. The water ballast makes use of the effect of energy lost through the shock front causing the water to break up into droplets creating a spray dome resulting in the attenuation of the energy imparted into the surrounding rock mass. Various tests have demonstrated that both the maximum overpressure and impulse density are significantly reduced when water of a minimum depth is in direct contact with detonating explosives. This innovative blasting technique reduced the excavation programme by three months, saved HK$5 million in direct costs and totally mitigated the impacts on the public and other stakeholders nearby the KGV Shaft. Peak Particle Velocities (vibrations) rarely exceeded 2-3mm/sec (0.08-0.12in/sec) at a distance of 30-40m (98-131ft) from the blast location and air overpressure levels were reduced below the Hong Kong target level of 120dBL. In total, 24 blasts were fired with an average advance of 1.6m (5.25ft) with an average powder factor of 2.03kg/m3 (0.127lb/ft3) to 1.84 kg/m3 (0.114lb/ft3). The initiation pattern had 5ms between sequentially detonating blastholes and 20ms between adjoining rings.

Jan 1, 2013

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

By D. Large, M. H. Davies, B. Driedrichs, U. Matzander

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A prototype high-resolution electromagnetic system, based on the theory of controlled-source magnetotellurics, was developed. The electrical source field is fed into the earth by dipoles at preselected frequencies and a multi-channel receiver measures five electric and three orthogonal magnetic fields. Suitable mapping algorithms and spatial filters are applied to the data and a new technique permits calibration during measurement. The system was field tested over a blind orebody, at 250-550 m depth, in the Aguas Tenidas area of the Iberian Pyrite Belt. Ten lines totalling 12 000 m of profile length were completed in seven days and the orebody was identified. Tests in the Irish Midlands suffered from strong electromagnetic interference of cultural origin

Jun 21, 1905

By Matthew Kowalczyk, Steve Bloomer, Peter Kowalczyk

"Mineral deposits found near seafloor hydrothermal venting are of great economic interest. Valuable metals such as gold, copper, zinc, and other polymetallic sulfides are found in appreciable grades in seafloor massive sulfide (SMS) deposits associated with these vents. For mapping these deposits, electromagnetic prospecting is one geophysical method that is very useful because copper/gold rich deposits are highly conductive.Ocean Floor Geophysics (OFG) in 2008 developed the first EM system to successfully map the limits of conductive mineralization in a survey at the Solwara 1 deposit (Kowalczyk, 2008). Since then, towed coincident loop time domain systems have been developed by Waseda University (Nakayama and Saito, 2016) and have successfully detected known mineralization buried at 30m depth. Using a deep tow controlled source electromagnetic (CSEM) array, very clear anomalies have been measured (Murton, 2017) over known mineralization at the TAG field on the mid-Atlantic ridge.In 2014 and 2015, OFG partnered with Fukada Salvage and Marine Co. Ltd. and the Scripps Institution of Oceanography to map methane hydrate deposits off the coast of Japan using a towed controlled source electromagnetic (CSEM) system developed by Scripps. These hydrate deposits are resistive targets, and the Scripps system successfully mapped subsurface electrical resistivity distributions to depths of several 100 metres below the seafloor. OFG is attempting to extend the Scripps CSEM technology to map subsurface conductive SMS deposits to a similar range of depths below the seafloor."

Jan 1, 2017

By Toshiaki Nakai, Kunihiko Takeda, Kimio Imaizumi, Hiroaki Shirasaka

"The new type of nano-porous silica particle was considered to be constructed by the spinodal decomposition-type process which was found to have narrower pores than those of conventional porous silica prepared from boron silicate or ""Shirasu"" balloon. Nano-porous silica particles were fabricated by the calcination of silica gel mixed with well-dispersed complex salts composed of phosphorous and molybdenum compounds. Both silica and inorganic salts were not perfectly dissolved in the suspension solution. After removing of the water, the silica-inorganic salts complex was volatized and successively calcinated at a temperature ranging from 650 °C to 800 °C. Then, the inorganic salts were removed by dissolving in hot water. Other inorganic salts such as potassium halides were also found to be effective as a pore-size controller.IntroductionControl of structure has an important role in the field of industry as well as in the separation and purification technology for metals and organic syntheses. Many studies on the control of material structures have been reported regarding porous materials with pores ranging from nanometer to micrometer scale. 1 ) One example is zeolite as a naturally yielded porous inorganic material. Various types of synthetic zeolites have been studied as ""molecular sieve"" materials with ordinary pore-size of less than one nanometer. In 1992, crystalline meso-porous material with a large surface area named MCM-41 was synthesized through the use of template synthesis. 2) In direct relation to our study, amorphous borate glass having 4 to 100 nm of fine pores known as Corning glass 3l or SiO2-Al2OrB2O 3-CaO porous glass having large pore dispersity ranging from 4 to 10,000 nm have been reported. 4 ) S) 6 ) Some examples of several reported studies are as follows: phase-separated porous glass consisting of B2OrAl2O3-ZrO2-RO-R2O complex oxide 7 ) glass with finer pore induced from hydrolysis of silane alkoxide, porous material attained by condensation polymerization through the use of sol-gel process 8), alumina meso-porous material 9 ) 10), silica-zirconia material 11), carbon porous material 12), etc.."

Jan 1, 2000

By Raden Haris Handayana, Jihan Farhan Lubis, Milia Putri, Tengku Deli Hamonangan Hasibuan, Sani Salahudin

An environmental issue that must be controlled from coal overburden blasting near the structure is ground vibration. Damaging ground vibration is the effect exerted from residual energy from blasting that does not work to fracture the rocks. Sebuku Tanjung Coal is a coal mining that operates T3 Pit adjacent to the High Voltage Tower. This structure is included in the Class 5 building with a maximum Peak Particle Velocity (PPV) of 40 mm/s. The shortest distance from the blasting location to the structure is 105 m. The initiation system used is electronic detonators combinate with emulsion as an explosives type. In Indonesia, the government regulated vibration limitation on SNI 7571:2010. The blast outcomes targeted are PPV below 40 mm/s, fragmentation size <80 cm for Excavator Komatsu PC-2000, and digging time <12 seconds. In this paper, the blast design was engineered by conducting Signature Hole Analysis for optimizing delay timing configuration and Scale Distance regression analysis to determine optimum charge weight per delay at the blast site. PPV results from 30 blastings achieved 100% below 40 mm/s with the range of about 1.773-30.250 mm/s. The deviation between PPV prediction to PPV actual is less than ±18% which provides the blasting with electronic detonator resulting in good PPV prediction for controlling vibration. The average fragmentation size (D80) is 55.81 cm in the 1st layer and 54.81 cm in the 2nd layer. The average digging time is 10.30 seconds in the 1st layer and 10.12 seconds in the 2nd layer.

Feb 6, 2023

By Anil Mahyera

Under contract to the Bureau of Mines, a roofbolting machine has been developed which will: control torque on the bolthead to within 4 percent of a set point, control thrust to a low level (150 lbf), and implement a tightening method to minimize variability due to bolt tension decay of a group of bolts caused by differing anchor creep rates. This bolter was used to determine bolthead and thread friction factors, and to determine the effect of adding a hardened washer to the bolt assembly on the uniformity of bolt tension in the laboratory and field. Recommendations for torquing speed, bolt lubrication, use of hardened washers, and thrust level on the bolthead are made. The relationship of this system to Improved roof control is discussed, along with additional work that remains to be performed. Patent Notice Patents are pending which protect the hardware and methods of controlling tension decay as discussed in this paper.

Jan 1, 1981