Search Documents

By R. U. Jackson

FACED with rising costs, the mining industry is looking to new methods and equipment to supply the relief necessary for profitable operation. Conveyor transportation is rapidly taking a superior position to motor tramming in underground mines because of lower installation, maintenance, and operating costs. Haulage is always a critical problem in underground mining. The ease of operation and flexibility of a haulage system can have an important effect on ultimate mining cost. With the average tenor of ores on the downgrade, larger tonnages are required for the same metal recovery. This selection of a tramming system can be the key to a successful, paying plant. Because this shift is being made at an ever advancing rate, it may become necessary to tailor mining operations to the transportation system, rather than to select a haulage system fitting set mining methods. In choosing a haulage system, the relative costs of the various methods are of the greatest importance. Adapting the mine to one or the other type of tramming is not considered in the cost analysis, and very likely would make little difference, outside of location of drifts and raises. In the cost sheet, the problem presents recommendations for a conveyor installation and a comparison of equipment, installation, operation, maintenance, and power costs are made. Under the track haulage estimate, no allowance was made for dumping equipment at the shaft pocket or bin. If this equipment was added to the balance sheet, the additional

Jan 1, 1952

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

By LeRoy D. Loy

To facilitate effective land reclamation and comply with existing state regulations, surface coal mine operators have in recent years adopted new mining techniques and equipment utilization for steep-terrain mining. In contrast to direct spoiling with draglines or shovels, these new mining methods require some form of overburden haulage from the excavation face to the point of reclamation. Although current mining methodologies such as Block-Cut, Modified Block-Cut, and Mountaintop Removal with Head-of-Hollow Fills have proven effective in achieving reclamation objectives, some production problems have resulted from pit congestion and excessive equipment delays. Recognizing this problem, the United States Bureau of Mines contracted Skelly and Loy to design innovative mining concepts utilizing conveyor haulage in place of trucks, loaders, dozers and scrapers. Project objectives required definition of current bottlenecks and development of mining systems to: alleviate bottlenecks; increase production potential; facilitate additional resource recovery; enhance reclamation; reduce safety hazards; and improve mining economics. Successful completion of project goals within a four year program involves systematic implementation of the following separate work phases: 1) Develop Concepts for Block-Cut Mining Systems; 2) Determine the Economic and Technical Feasibility of Concepts; 3) Prepare Detailed Design and Specifications of Concepts; and 4) Prepare Specifications for Conducting Field Tests of the Most Promising Concepts. At the time of this publication, Phases 1 and 2 are finalized with Phase 3 efforts well underway.

Jan 1, 1977

By Todd Hollingsworth

The Boddington gold mine is located near Perth in Western Australia in the Saddleback Greenstone Belt, a fault-bounded sliver of Archaean volcanic and shallow level intrusive rocks, surrounded by granitic and gneissic rocks. The mine began operations in 1987, producing about 7.7 t/a (250,000 oz/year) until mining ceased in 2001. Built on the footprint of the original mine, the Boddington gold mine expansion project involved opencut mining from two large pits. Expected gold production is around 31 t/a (1 million oz/year) for the first five years. It will be the largest gold mine in Australia. The mine has proven and probable reserves of more than 622 kt (20 million oz) of gold and has an expected life of more than 24 years. The mine is currently solely owned by Newmont Gold Corp., the world?s second-largest gold mining company, employing around 28,000 people worldwide. The conveyor and belt feeder contract for the Boddington gold mine expansion project was awarded by Aker Kvaerner Clough Murray Roberts (AKCMR) to FLSmidth Conveyor Engineering Inc. in August 2006. The contract involved the design and manufacture of 15 conveyors and 17 belt feeders with belt widths ranging from 450 mm to 2.4 m (18 in. to 96 in.) and conveyor lengths from 16 m to 2,172 m (52 ft to 7,125 ft). The total motor power added up to more than 16,700 kW (22,400 hp). The total length of all belting was almost 11.5 km (7.1 miles), and the total fabricated steel weight was approximately 3.7 kt (4,100 st).

Jan 1, 2010

By A. R. Anderson

UNTIL recently all discussions directed at justify-ing the use of mechanical-loading equipment and conveyors have referred chiefly to tons per man and cost per ton. But there is another consideration that ? will speed the adoption of mechanical loading in mines even though tons per man on present day stand-ards were not increased nor the cost per ton decreased. With restricted immigration, improved facilities for education in our mining communities, and increased opportunities for recreation, the type of man who can or will throw 20 tons of coal per day over the side of a mine car is disappearing. Whether we will it or not provision must be made to replace muscular effort by mechanical means. Fortunately, indications are that the process will be accompanied by increased output per man and lower production cost, and though the outlook may now be a bit clouded in spots, all should profit by the change. The operator should enjoy a more stable business with more assured profit, the miners should get a better livelihood with less arduous effort and under safer and pleasanter working conditions, and the consumer should gain the assurance of a supply of coal always available at reasonable prices. That sounds like the millennium in the coal business perhaps. Of course, it is not, but there is just enough of that millennium stuff in it to encourage those of us who are working with today's problems of applying loading and conveying equipment to underground opera-tions. If we discern clearly that there can be no back-sliding, and that all will share in whatever advantages accrue, we will carry on more vigorously, and may right-fully expect to have the necessary cooperation of all the elements within the industry. As nature does not seem to have followed a definite plan in the formation of coal deposits it is not likely that any one standard method or type of equipment can be evolved for mining the coal. The method of mining that maybe most advantageously employed with load-ing machines and conveyors depends on the character of the strata overlying the coal as much as anything else.

Jan 4, 1927

By R. P. Stahura

In many ways, conveyors are the lifeline of mining and processing operations. Like arteries in the human body, they continuously supply materials to and carry finished products and waste away from vital on-going operations. And like arteries, when the conveyors are running with less than maximum efficiency and productivity, it spells serious trouble for the operation's overall health. Inefficient conveyors suffer carryback, leading to the build-up of materials on idlers and other expensive components. They spill and leak material at loading zones and conveyor transfer points, causing accumulations that can damage the belt, wear moving components, and increase both clean-up labor and maintenance expense. They wander or mistrack, spilling material and endangering personnel and conveyor components including the belt itself. And through these inefficiencies, they multiply the operation's hidden costs. These added expenses are created in lost production, increased downtime for service and maintenance, and the cost of the replacement of prematurely worn equipment. In addition, the attitude that inefficiency is "good enough" is recognized elsewhere in the organization; as a result, other departments relax or operate at less than peak performance. Quality goes down and with it employee morale.

Jan 1, 1992

Chromite ores have a long history of low pricing and for AustraliaÆs only chromite mine this has been a particularly tough challenge, especially as the mine is located nearly 400 km from the nearest port at Port Hedland. A stockpile of chromite fines (-16 mm) has been built up since 2003. The opportunity to develop a facility to treat this material to produce a chip (-16 + 1 mm) product and a sands (-1 mm + 45 micron) product was taken when the price increased to above US$140/t. A simple add-on plant containing a heavy media cyclone circuit for the chips and a spiral circuit for the sands was designed and developed. During construction of the fines plant the price of chromite reached a level where the payback for the entire project was less than eight weeks. Soon afterwards the price and the demand for chromite plummeted and the site was put on care and maintenance, except for the commissioning of the fines plant. This put considerable pressure on whether to continue to operate the plant or to place it in care and maintenance. Times of boom and bust provide management with almost totally opposite views. By not taking a conservative view on prices and costs, the effect of extremely low prices and minimal demand can be devastating to a good project. Designing and building plants with conservative costings in boom times gives a greater chance of keeping projects alive during the bust periods that tend to follow.

Jan 1, 2009

By J Paradis, K Dudgeon, M Topping

At Newmont’s Jundee Operation, exploration and resource geologists collaborated to produce an open pit resource model. Using a variety of modelling and estimation techniques but no new data, an uneconomic underground target was converted into a potentially economic open pit evaluation. During an industry downturn, it is more important than ever to efficiently share expertise, ideas and resources to problem solve and produce meaningful project outcomes. The two departments brought together different methods and ideas, and the process showed that certain methods worked better than others in different situations, thus the appropriate method was applied to each part of the evaluation. The results were used to create new procedures and improved lithology modelling and resource model estimations. Adaptability of the geology departments and collaboration such as this are key to ongoing improvements and future mine life at Jundee.CITATION:Dudgeon, K, Paradis, J and Topping, M, 2014. Cook open pit model – the hurdles: how we leapt, lunged, stumbled and overcame them, in Proceedings Ninth International Mining Geology Conference 2014 , pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Vernon R. Shorter, Wayne N. Clark

Introduction Coal is the US's largest indigenous fossil fuel resource and is used to power 57% of this country's electrical generation (NCA, 1986). Congress, however, is focusing its attention on the acid rain issue and public sentiment is leaning toward further curtailments of SO2, NO, and particulates from utility and industrial coal-burning facilities. The Cool Water plant has proven that integrated-gasification-combined-cycle (IGCC) technology can reliably produce economical electrical power while limiting SO2, NOx, and particulates to a rate of only one-tenth of the federal New Source Performance Standards for coal-fired plants. Process water requirements at Cool Water are 40% less than those of a conventional coal-fired utility plant equipped with flue-gas desulfurization units for stack gas scrubbing, thus reducing waste water treatment requirements (Clark and Shorter, 1985). The IGCC technology employed at Cool Water has now been demonstrated to efficiently convert coal to electricity in an environmentally superior fashion. The Cool Water Coal Gasification Program is an unincorporated California association of six partners whose commitment is proving that the integration of gasification with combined cycle power production (IGCC) is commercially viable and environmentally safe. The 120 MW Cool Water plant began commercial production on June 24, 1984. The Program is operating it for a five-year commercial demonstration period. The Program is about halfway through this period. Much of that which was intended to be proven is now fact. In this mid-term assessment, the authors report that the com-

Jan 2, 1987

By Will D

This presentation is to outline the current practice of mechanised stoping a one-metre wide, gold bearing ore body to optimise fragmentation, minimise dilution and reduce stoping costs.Coolgardie underground operations have historically been mined using traditional shrink stope methods, but in this recent economic environment (with falling gold prices and high costs of traditional methods) it was necessary to look for alternative methods in order to reduce costs and increase productivity.Although still in a learning and refinement phase, CGNL is satisfied that it is feasible, practical and more economic to use mechanised long up-hole stope and long-hole rising methods to significantly reduce the mining cost, reduce dilution, increase safety and increase productivity three-fold compared to traditional airleg methods used throughout the Fasten Goldfields.

Jan 1, 1993

By Walter Weeks

THE process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. CASE I If compressed air is allowed to expand to the atmospheric pressure through an orifice in an air line that is supplied by a running compressor, no cooling results except the negligible one due to the Joule-Thompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected.

Jan 1, 1937

By Walter S. Weeks

THE process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. Case 1 If compressed air is allowed to expand to the atmospheric pressure through an orifice in an sir line that is supplied by a running compressor, no cooling results except the negligible one due to the Joule-Thompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected. Symbols P1 Absolute pressure in pipe line, lb. per sq. ft. P3 Atmospheric pressure, lb. per sq. ft. V1 Volume occupied by 1 lb. air in pipe. V3 Volume occupied by 1 lb. air at P3. Cv Specific heat of air at constant volume, B.t.u. per lb. per deg. F. Cp Specific heat at constant pressure, B.t.u. per lb. per deg. F. T1 Absolute temperature of air in pipe, deg. F. T3 Absolute temperature of air outside after expansion and mixing and coming to rest. J Mechanical equivalent of heat (778 ft. lb.) R Gas constant for air, ft-lb. per deg. F. = 53.3. Formulas Consider 1 lb. of air moving out of a pipe. The air behind it does work on it to the extent of P1V1 ft-lb. This work is really done by the thrust of the piston of the compressor and does not come from any energy that exists in the air in the pipe. The pound of air contains

Jan 1, 1937

By Martin Chabicovsky, Milan Hnizdil

Emulsions are frequently used for the cooling and lubrication of working rolls during the cold rolling. The fact that the lubrication and cooling are not separable makes the optimization of both functionalities difficult. The higher emulsion temperature decreases the cooling efficiency compared to cold water. Heat transfer and fluid flow laboratory (Czech Republic), CRM (Belgium), Tata steel (Netherlands) and Henkel (Germany) cooperated on the increasing of a cooling efficiency during cold rolling. Part of this research was focused on an influence of the emulsion composition on a cooling intensity. The cooling efficiency was laboratory investigated. The stainless steel sample with thermocouple was heated and then it was cooled by a nozzle. Tests were performed with various emulsions and pure water. The heat transfer coefficient was computed from measured temperatures. The cooling intensity (heat transfer coefficient) of all tested emulsions was similar but an increase of the cooling intensity was found with water. Further various emulsions concentrations were tested. Results showed decreasing cooling intensity with increasing oil concentration. Adding additives therefore is thought to cause a noticeable decrease of the cooling intensity.

Oct 1, 2019

By Yoshio Hiramatsu

In Toyoha mine near Sapporo, the ground temperature is very high, perhaps due to inflow of hot mineral water, the origin of which may be rock masses intruded by the igneous activity in the Tertiary period. The rock masses are found about 2 km east of the mine, their temperature being estimated at from 770 to 870 K at a depth of 3 km. In this mine several veins bearing zinc and lead ores have been mined down to the depth of 300 m from the level of the main entry, of which altitude is 551 m above the sea level. Formerly no attempt was made at development of the deeper part of the mine than the 350 m level from the main entry. Let us indicate hereafter the levels in this mine in such a way that the level 300 m deep from the main entry is denoted as 300 mL. Since 1974, however, the 450 mL of Tajima vein has been developed by deepening No. 5 Shaft to, and by driving drifts in the level. Much hot mineral water has been flowing into the drifts from rock. After twenty-eight months from the beginning of development, the total length of excavation amounted to about 1300 m. The success in development so far may be attributed to cooling rock and air with chilled water and to adopting heat-resisting explosives and detonators. This cooling costed very much and for further development in this level a more effective and economical cooling is desired if possible. To obtain fundamental data for designing an economical cooling, the authors investigated, as a preliminary study, the heat balance in the main drift of 450 mL, by measuring the temperatures of air, rock, hot mineral water, the rates of flow of air and water and so on, in August 1976. They are now carrying out continual measurements of the variations in rock temperature, air temperature and humidity with time. The present paper describes the details of the preliminary study.

Jan 1, 1980

By E. P. Palmatier

RECENTLY a cooling system has been in process of installation on the 3400 and 3600-ft. levels of the Magma copper mine at Superior, Ariz. The general system of ventilation employed at this inclined-vein mine is as follows: Ventilating air enters the shafts on the western side of the mine. Booster fans at each level each deliver approximately 38,000 cu. ft. per 'min. to the drifts. This air passes diagonally upward to the upper levels of the mine on the eastern side, where it passes up the shafts to large exhaust fans on the surface. Owing to the dip of the vein, all operations on the eastern side of the mine are above the 2500-ft. level, and those on the western side below the 2500-ft. level. At present, 2500 lineal feet of new drifts are being driven-on each of the 3400 and 3600 levels. The rock temperature is about 135°F. Until the new installation is completed, ventilating air for the two levels is supplied through Flexoid tubing from small booster fans -on the 3200-ft. level. The air picked up by these booster fans has a dry-bulb temperature of approximately 85°F. and a wet-bulb temperature of 82°F. By the time this air reaches the end of the Flexoid tubing at the 3600-ft. level, the dry-bulb rises to 101°F. and the wet-bulb to 86°F. The conditions at the head of the new drift were 102' dry-bulb and 93' wet-bulb.

Jan 1, 1937

By F C. D Michelin

As mines get deeper, the critical underground temperature limits will be exceeded, and an increasing number of mines will need to implement, expand or modify cooling systems. Surface cooling plants have many advantages over underground cooling such as efficient heat rejection, and lower relative capital cost; however the delivery of cooling through long underground distances can result in lost refrigeration capacity before the chilled air reaches the areas it is needed most. Refrigeration plants are therefore often overdesigned in size and capacity to compensate for underground losses.More mines are now utilising real-time monitoring and automated control of ventilation airflow and fan systems to ensure the conditions underground are safe and productive, and power consumption is efficiently managed. There may be significant opportunities to extend ventilation monitoring and control into the refrigeration delivery and control system.Energy reduction is an effective way to reduce costs and CO2 emissions, which is an increasingly important part of corporate governance. More efficient refrigeration control is a further step toward reducing energy consumption. This paper looks at an added step in how real-time monitoring can assist in controlling the output and chilled air delivery of a cooling plant. The requirements, implementation, benefits and challenges will be discussed.

Oct 12, 2022

By B Belle, M Biffi

Cooling of coal mines in the Bowen Basin, characterised by steep geothermal gradient, is presently achieved mostly through rental surface bulk air cooling in summer months. This paper argues that future mines will be required to focus their cooling resources more intensively to manage a challenging thermal environment where virgin coal temperatures of over 50¦C at a depth of 500 m are expected. Currently, mine cooling systems are employed to maintain the wet bulb temperatures (WBT) to below 27¦C at which point the risks of heat stroke or other heat-related issues are manageable. The capacities of these systems are in the range of 6 MWR to 10 MWR. The relationship between high working temperature environments and injury frequency rates is well established. Therefore, provision of appropriate cooling strategies and understanding their optimum performance and suitability are important to Australian coal mines of the future. This paper evaluates the underground temperature profiles of deep, gassy coal mines with propensity for spontaneous combustion and proposes the long-term cooling pathways to effectively manage thermal hazards. Thermodynamic modelling is performed on a longwall face and includes air leakage effects from goaf streams at various locations along the longwall face. The strategy summarises the application of underground bulk air cooling, chilled water sprays on the shearer and the resulting temperature profiles. Considering the new mining projects planned for the Bowen Basin region, a review of implementable cooling strategies such as mid-gate mobile bulk air coolers (BACs), spot coolers, underground bulk air cooling and the use of chilled water to enhance the positional efficiency of cooling plants, are discussed in this paper. Finally, the comparison of ærentalÆ versus æownershipÆ of cooling plants is analysed as part of long-term cooling strategies.CITATION:Belle, B and Biffi, M, 2013. Cooling pathways for deep Australian longwall coal mines of the future, in Proceedings The Australian Mine Ventilation Conference , pp 223-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

Anglo Platinum is in the process of introducing a number of initiatives, varied in nature, on a scale that will impact operations in the short, medium and long-term. The advent of mechanization on a large scale and the introduction of new mining technologies therefore require a different approach to the design of ventilation and cooling systems. In addition, the ventilation and cooling systems serving increasingly deeper operations will place a greater demand on electrical power consumption?this in an environment where power generation is limited and increasingly expensive. Ventilation and cooling systems currently being employed in platinum operations have evolved from practices first pioneered in deep level gold mines. However, in modern and future platinum mines, deepening of operations will take place in a somewhat different environment?particularly in terms of geothermal settings and electrical power utilization. This provides the opportunities to devise novel and energy-efficient ventilation and cooling strategies tailor-made to meet these challenges. The need for refrigeration and cooling at depth will increase the capital and operational cost component of ventilation systems and the medium-term limitations on the availability of electrical power will require the provision of innovative systems. The increased use of diesel-powered vehicles underground, the viability of energy recovery and feasibility of thermal storage opportunities are discussed in this paper. Some of the challenges and the solutions currently proposed in terms of ventilation system design, refrigeration plant selection and chilled water distribution methodologies are described. Changes in strategies core to this discipline that affect the health and safety of employees and the profitability of modern operations are deemed necessary to support the transformations that are envisaged.

Jan 1, 2008

By N. B. Pilling

THE development of a proper treatment for shells in connection with war contracts has brought to our attention the fact that the temperature of the liquid bath in which steel is quenched has a decided influence on the speed of cooling in the case of some liquids and very little in the case of others. Widely different physical results have been obtained by the use of water spray, water immersion, and oil immersion and further experiment has shown that the quenching effect of water used as a spray or an immersion varies greatly with the temperature of the water. The present experiments were undertaken with the idea of obtaining information of a quantitative nature regarding the quenching properties of a number of liquids used commercially in hardening steel. The general features of such cooling media are common knowledge and in the literature may be found records of numerous attempts to evaluate the cooling power of a liquid when used as a quenching bath. Much, if not most, of the data given on this subject is in the form of a simple statement of the time required for a certain heated mass to cool between two arbitrary temperatures when immersed in the liquid, quite regardless of the path of the temperature change. Our own purpose has been somewhat different. We have attempted to isolate that property of these. liquids having to do with their ability to absorb heat rapidly, as distinct from the behavior of a considerable mass when exposed to different thermal environments. More specifically, from the data obtained through autographically recorded cooling curves of a small standard mass quenched under various conditions, we have tried to analyze the mechanism of heat absorption by the several liquids, measure the changes in its rate as a function of the temperature of the surface of transference, and ascertain the influence of the temperature of -the liquid itself upon both.

Jan 9, 1919

H. M. HOWE, Bedford Hills, N. Y.-One wonders, whether it might not be well to check, by a rather simple and direct way, the inferences that would be drawn from this investigation. Suppose we quench, in these various liquids cylinders of steel, selecting material that is not likely to split in hardening, and then examine their cross-sections micro-scopically. If the cylinder is of any size, you will find a series of concentric bands, a very hard band, a softer band, and a hard band-but it seems that here would be a way of checking the inferences from the cooling curves by comparing these waves of hardness obtained in similar speci-mens quenched in different liquids. One would think that there would be great promise in that way. One's first thought is to quench similar pieces of steel, similarly heated, in different liquids and determine their hardness. I suppose many of us have tried that. We then meet the-difficulty that it is not the most rapid cooling that gives the greatest hardness. There is an intermediate rate of cooling that gives maximum hardness so that you can not by any simple method as that check this cooling method. But it seems possible

Jan 12, 1919