Search Documents

Contents

Jan 1, 1985

By A. M. McKim

6, 7.3 meter diameter autogenous mills at Wabush Mines are undergoing conversion from a radial configuration of pulp discharger to a curved design. Improved discharging efficiency has effectively lowered the pulp level in the mill. The low level operation enhances the grinding efficiency netting a 12% power reduction. Significant reductions to rate of wear has been a spin off benefit. The design incorporates features for holding the assembly solidly in place thus eliminating bolt hole damage and leakers. Preliminary work in one 11 meter mill at Hibbing Taconite did not indicate that all the same advantages were available in their process.

Jan 1, 1982

By W. F. McDermott

The Iron Ore Industry has perhaps seen more varied and drastic changes in its approach to crushing and grinding in the last 5 years than any of the other mineral industries, Multimillion ton per year plants have become common place. Centralized control and computers have become an established benefit. Autogenous grinding along with a variety of rod and ball grinding flowsheets are in use. This morning I will discuss a few of the more important and new concepts in the control of these crushing and grinding circuits.

Jan 1, 1970

By R. C. Miranda

This paper intends to demonstrate the applicability of tools for advanced process control and online particle size image analysis in crushing and autogenous grinding circuits. In a crushing plant, cameras are installed in the conveyor belts of the circuit products. The vision system continuously processes the acquired images and thus obtains the variation of the size distribution curve. From these measurements, the advanced control system can operate, for example, at the opening of the crusher, in order to keep the P80 in the desired range. In addition, through the power information and level of the crusher's chamber, it is possible to increase the capacity of the crushing circuit. If the crusher is not equipped with an automatic opening adjustment, a warning may be issued to the operator to provide this setting manually. In mineral processes that use autogenous and semi-autogenous grinding for fragmentation, obtaining online F80 through the vision system allows for manipulating the parameters of rotation speed and solids concentration, through which the amount of material at the critical particle size that is produced can be controlled. In addition, the noise produced in the mill can be measured and controlled. Thus, it is possible to prevent breaches and to optimise the mill capacity for grinding. Image analysis combined with an expert system that translates this information and acts to seek the most appropriate particle size distribution, brings greater stability to the process optimising the capacity of the equipment, which allows for significant gains in production.

Sep 1, 2012

By John Gross

From the time when man first pounded one rock upon another or used heat and sudden chilling with water to disintegrate rock, the art of crushing advanced but slowly to the mule-driven arrastre and the Chilean mill stage until the advent of power-driven appliances made material progress possible. The combined efforts of manufacturers and operators have made modern machines highly efficient mechanically. Although marked progress has been made along mechanical lines, the theory and conception of underlying principles have not advanced so rapidly. This lack of advance in theory may be attributed to the unfortunate situation resulting from the controversy as to whether the Rittinger or the Kick law is applicable to crushing. Many pages of the technical literature are burdened with theoretical discussions in favor of one or the other of these laws, which have tended to cloud rather than to clear the atmosphere.

Jan 1, 1938

By J. J. DeMull, B. A. Boster

Amax's Sleeper mine uses conventional cyanidation milling and heap leaching techniques to produce gold. Since milling operations commenced in March 1986, average ore processing rates have improved from the design rate of 455 t/d (500 stpd) to more than 720 t/d (795 stpd). Heap leaching was added to the process facilities in September 1986 at a design rate of 1.5 kt/d (1650 stpd) and current heap leaching rates exceed 2.7 kt/d (2950 stpd). Presented are descriptions of the Sleeper processing facilities with emphasis on the crushing and grinding circuits, a review of the selection of crushing and grinding equipment, and a summary of operating performance during the first 16 months of operations.

Jan 1, 1990

By T. J. DeMull

AMAX's Sleeper Mine uses conventional cyanidation milling and heap leaching techniques to produce gold. Since milling operations commenced in March 1986, average ore processing rates have improved from the design rate of 455 tonnes per day to more than 720 tonnes per day. Heap leaching was added to the process facilities in September 1986 at a design rate of 1,500 tonnes per day, and current heap leaching rates exceed 2,680 tonnes per day. Presented are descriptions of the Sleeper processing facilities with emphasis on the crushing and grinding circuits, a review of the selection of crushing and grinding equipment, and a summary of operating performance during the first 16 months of operations.

Jan 1, 1988

By R. L. Beatty

Bond International Gold's Colosseum gold mine was discovered in 1865. No recorded production occurred, however, until the 1930s, with production of about 19 kg (615 oz) of gold. The mine was closed in 1942 as a nonessential industry during World War II. The property was acquired by Dallhold Resources in mid-1986. Construction of a 1.1-million Mt (1.2-million st), carbon-in-pulp (CIP), cyanide mill began in November 1986 and was completed in September 1987. Minable reserves are estimated to be 9.5 Mt (10.5 million st), with an average grade of 2.1 g/t (0.061 oz per st). This article describes the general process flow and plant equipment. And it looks at the maintenance and operational problems encountered in the first six months of operation. Process description Ore is direct hauled from the open-pit mine 1.5 km (1 mile) to the crushing facility. There it is crushed to -152 mm (-6 in.) with a single- stage, 1.5-m x 1.2-m (60-in. x 48-in.), 186.5-kW (250-hp), Fuller-Traylor jaw crusher. The ore is then stockpiled in a 31.7-kt (35,000-st) reclaim ore pile. Lime is added to the crushed product as it is conveyed to a single 6.4-m x 4-m (21-ft x 13-ft), Hardinge semiautogenous grinding (SAG) mill, followed by a single 4.3-m x 7.3-m (14-ft x 24-ft) Hardinge overflow ball mill. After grinding, the slurry is thickened and then preaereated for three hours. Following preaereation, the pulp is leached with NaCN at a pH of 11, also for three hours. The slurry then goes through a seven-stage CIP circuit for 21 hours. Then the tailings slurry is preaereated for three hours before cyanide destruction using the Inco process. Loaded carbon is eluted using an Anglo American strip, followed by electrowinning on stainless steel wire. The stainless steel wire is transferred to refinery cells where the gold and silver is plated on stainless steel plates. Following electrore-fining, the gold-silver foil is removed, melted, and poured into dore bars for shipment. The crushing, milling, refining, and maintenance processes require 37 people. Crushing The crushing area required changes and modifications following start-up. Several areas are of specific note. Structural failures Rubber support cushion blocks located under the coarse ore bin failed. These were replaced with heavier, more durable blocks and have since appeared to be satisfactory. A severe structural vibration was encountered in the entire crushing facility. A mechanical engineer, brought in by the contractor, determined the structure needed more support and cross-bracing.

Jan 1, 1989

By Larry S. Diaz

It is felt that prior to the presentation of the technical portion of this paper, some general information would be of interest. The Sar Cheshmeh Copper Mining Company was founded by the Iranian Government to oversee the design and construction of Iran's first copper smelter complex, which will be another step in the industrialization of Iran. Since this is the first such plant in Iran, Sar Cheshmeh wisely chose to enlist the technical assistance needed in regard to the facilities requiring engineering and operating know-how from outside of Iran. To obtain the foregoing, SCCM signed a contract with Anaconda-Iran, Inc., which was formed by The Anaconda Company for this project. The general scope of this contract covers the overseeing of engineering and design by Parsons-Jurden as well as physical plant construction. In addition to this, the same services were given to water supply and tailings disposal systems which were not included as part of the Parsons-Jurden contract. Anaconda-Iran is also assisting SCCM in setting up a training program for Iranian personnel for plant operations, administration, etc., which .will go on for some time after the plant startup, under the guidance of Anaconda-Iran expatriates. SCCM?s other responsibilities, in respect to the development of this industrial effort, are the building of a townsite for approximately 2200 families, the expected manning requirements, having all the facilities necessary to provide a pleasant life in a remote area. It has been estimated that the manpower for operations will be 2050.

Jan 1, 1976

By Phil Dakin, Rajiv Chandramohan, John Lo Grande, Greg Lane

Crushing and grinding circuit availability is a critical design factor defining the installed equipment selection and the process buffers required to maintain throughput during maintenance. The comminution circuit typically accounts for a process plant’s largest capital expenditure and energy use. Effective process and equipment selection and layout optimization are crucial steps when combining the objectives of cost-effective design and high circuit availability in operation. This paper outlines fit-for-purpose design principles for optimizing process flow, eliminating standby equipment and reducing buffer residence time whilst improving maintainability and operability.

Feb 1, 2025

By B. Fagerberg

Crushing and grinding practice in Sweden follows largely the international pattern. Certain special circumstances, however, have had an influence on the development. Most mines are worked underground in either quite small or in very large units. To utilize small sulphide ores, custom milling is rather common. Apart from the cement industry, the rock species treated are hard and abrasive. Another important factor is the increasingly strict requirements placed on the mechanical condition of different products, especially lump ores and coarse iron ore concentrates. A significant feature in the design and development of Swedish crushing and grinding practice has also been close cooperation between machinery manufacturers and the users. An account of these conditions and an outline of the crushing and grinding techniques employed in Sweden are presented in this paper with emphasis on the mining industry. For background purposes it may be mentioned that crude ore production in Sweden last year included 45 mill. tonsx) of iron ore, of which some 20 mill. tons from Kiruna alone, and 4 mill. tons of sulphide ore from 22 other mines, fig. 1. In addition 8 mill. tons of limestone were quarried for cement production and several million tons of stone and sand for roads, aerated concrete, etc.

Jan 1, 1968

By J. F. Myers

THE Tennessee Copper Company's operations are in the Ducktown Basin, in the extreme southeast corner of Tennessee. The ore is of the heavy sulphide type, the predominating sulphides being pyrite, pyr-rhotite, chalcopyrite and sphalerite. The gangue is a micaceous schist, with varying amounts of free quartz. The mining operation develops two classes of ore, each of which is concentrated by the flotation process in separate mills. Table 1 shows a typical analysis of the ore treated in each mill. TABLE 1.-Typical Analysis of Ore Treated Composition, Per Cent Mill Tons Capacity Cu Fe S Zn London 1,350 1.41 28.4 20.2 1.10 Isabella 850 0.69 44.7 31.6 0.31 LONDON MILL The London mill was built in 1922, with a capacity of 400 tons per day. This was gradually increased to 600 tons by 1926, to 900 tons in 1928, and to 1350 tons in 1938. Fig. 1 shows the crushing and grinding flowsheet in 1928, when the capacity was 900 tons; Fig. 2, the crushing and grinding flowsheet that was developed by 1938, for the treatment of 1350 tons per day. A comparison of these flowsheets reveals that this increase in tonnage, with a subsequent improved operation, was accom-plished with identically the same major equipment. Improving a concentrator's capacity, metallurgical results, and costs as time goes by is a commonplace practice, and is accomplished in various ways, depending upon the local conditions. The reason for presenting the data of how this was accomplished in the mills of the Tennessee Copper Co. is that a fast-running rod mill plays such an interesting role

Jan 1, 1940

By G. P. Holmes

"IntroductionThe copper-molybdenum property of Brenda Mines Ltd. is located 18 miles north west of Peachland in the Okanagan Valley of the Southern Central interior of British Columbia. The actual site is 50 miles north of the international boundary and 150 air miles east of Vancouver at an elevation of 5000 feet above sea level. The earliest written mention of the prospect is found in the Geological Survey of Canada, Memoir No. 243, issued in 1947 by Dr. H.M.A. Rice. In 1954 the area was staked by a prospector, Bob Bechtel, who interested Bern Brynelsen of Noranda Exploration in examining the claims. A joint Noranda - Kennecott program resulted but since the grades were so low the property was not taken up until in 1964 a re-examination by Chapman, Wood and Griswold produced recommendations leading to the construction of the Brenda Mine as it is today.The rounded, timber covered mountains of the area are composed of the tuffs, argillites and limestones of the Upper Triassic Nicola Group, which is intruded by a Jurassic quartz diorite, called the Brenda stock0 The actual orebody occurs in a strongly fractured zone within the Brenda stock, approximately 1500 feet from the contact with the Nicola group0 The ore minerals, .chalcopyrite and molybdenite, associated with pyrite and magnetite of lesser importance, occur as fillings within the fractures 0 The grade of the ore decreases outwards from a central higher grade core and in January 1971 total reserves were estimated at 165 million tons assaying 0,182% Copper and 0,049% Mo."

Jan 1, 1972

By Bertrand Robinson

Epitomized, there have been no innovations recently in crushing, but in grinding the trend has been towards larger units under more automatic control with an increased use of autogenous grinding. Crushing Portability of primary crushers to "follow the face" reduces material handling costs. The top size of crusher feed still establishes the size of the crusher; the feed opening should be 1 1/2 times the size of the largest feed. The maximum size of crusher product is 1 ½ times the open scale setting of a jaw or gyratory crusher. Practice dictates use of scalping screens ahead of any type of crusher when the feed contains 25% or more of product size. If required capacity is under 600-700 tph economics favor a double toggle crusher or an impactor. For larger capacities the gyratory crusher is favored.

Jan 1, 1970

R. S. Shoemaker: Our first question is, is there a need for a grizzly before a primary crusher? What is its effect on crusher capacity and crusher maintenance? Is it worth the extra capital cost in a crusher installation? Vincent: ASARCO has a grizzly at Mission. Utah Copper uses grizzlies ahead of their gyratories. There is some quite abrasive ore at Mission, an argillite type of rock, which has a work index of 16.5 to 20, which is getting up toward the taconite classification. We get a life of 12- 16 million tons per set of concaves or per mantle with the grizzly ahead of the crusher. At Duval Corp., some 6 miles to the south of Mission, their crusher installation on a good, hard rock does not have a grizzly, and the last information I had is they get a life of about 2 ½ -3 million tons on their mantle and concave. At Silver Bell, our other copper unit in Arizona, they do not have a grizzly ahead of the gyratory and there they get a life of about 5-6 million tons. At Utah Copper, which we all know is a fairly soft ore, relatively speaking, they get a life of 24-27 million tons with grizzlies ahead of the crushers. I think a grizzly has a very definite effect on the life of the mantle and the concaves. As far as a jaw crusher is concerned, I think that usually it is desirable to have a grizzly if it is properly designed, which means it is self- cleaning. Otherwise I would not like to see one in the circuit.

Jan 9, 1967

Shoemaker: We've all heard a lot about epoxy liner backings. This brings up the question-do zinc furnaces still have a place in a new plant? Meaders: I would, you must understand, be prejudiced in this question because we introduced epoxy backing into the industry. Naturally, we wouldn't have done so if we didn't think it should be done. With that background maybe I could give a little more information on this particular subject than some of the others, because we now have been in this business for some three or four years.

Jan 11, 1967

By John Gross

THE deductions drawn in crushing and grinding operations have heretofore been based on a separation of the products into various sizes. A crushed product may be sized by sieving, by elutriation, and by aid of the microscope. To estimate the surface of each size the relation of the surface to the estimated average diameter must be assumed. Such a relation, owing to the irregularity of the particles, may involve two assumptions: First, a factor to convert average diameter to surface for one particular size; and second, a variation in the factor as the diameter of the particle changes. Obviously a surface measurement in which such assumptions and estimates are involved is questionable. In the first paper of this series1 a method has been given by which an accurate measure of surface of quartz can be obtained from its dissolution rate. By the use of this method, surface measurements have been made on a series of sieve sizes of crushed quartz, the results of which are given and discussed in this paper.

Jan 1, 1928

By John Gross

A SURVEY of the status of ore dressing in 19231 placed particular stress on the need of research in the crushing and grinding of ore, especially on the need for a method of measuring the surface of the products obtained in crushing and grinding, and for fundamental data on the law of crushing, in order that intelligent conclusions may be drawn from actual crushing or grinding experiments. There has been no satisfactory means of determining the surface of crushed products. The results have been judged entirely by the amount of the various sizes produced, based on sieve sizing for particles above 74 microns in size and on microscopic measurement or elutriation for particles below 74 microns, a method which could give only a general idea of what had been accomplished. The fact that the long controversy between the followers of Kick and of Rittinger has resulted in no accepted conclusion is evidence of the need for fundamental data on the crushing law.

Jan 1, 1928

By John Gross

THE method of measurement of surface on quartz particles was given in a previous paper.1 With such a method the relation of surface produced in crushing quartz can be compared to the work in crushing without recourse to sieve sizing or microscopic measurement. In crushing, the work input must be known with a fair degree of accuracy. With crushers, rolls, ball mills, and similar apparatus the measurement of the work in crushing is subject to possible errors, due to friction in .the transmission as well as in the machine itself. Moreover, relatively large quantities of material must be crushed to get an average figure. In the selection of a method of crushing, simplicity in design and operation was desired and this was most readily obtained by the use of a free-falling body. A description of the apparatus embodying this principle is given herewith. THE CRUSHING DEVICE The apparatus used is shown in Fig. 1 and in cross-section in Fig. 2. The material to be crushed is placed in the crushing chamber C in the steel mortar M. The mortar is 3 in. dia. by 3 in. high. Two mortars are used, one having a crushing chamber 1-in. dia. by 1/2 in. deep, with a capacity of 4 g. of quartz, the other having a crushing chamber 1 ½ in. dia. by 3/4 in. deep, with a capacity of 12 g. of quartz. The position of the mortar is adjusted by means of three centering screws A. The steel plunger P, which fits neatly into the chamber, is placed on top of the material to be crushed. Plungers of different lengths were tried and as they were found to give practically identical results the length adopted was equal to the depth of the chamber.

Jan 1, 1928

By Earl R. Johnson

Ore broken at the mine or quarry face generally is loaded by power shovels into large trucks or rail cars and hauled to a primary crushing plant where it is reduced to a more workable size for ease in handling. The primary crushing plant is customarily located as close as possible to the center of gravity of the ore body and the projected limits of the mine pit to minimize the cost of hauling and to increase safety from flying rock as a result of blasting operations. A belt conveyor is used to transport the crushed product to a nearby ore treatment plant or, should this plant be located some distance away, the ore is loaded directly into cars and hauled by rail. Between trips the crusher product is accumulated in bins or stock piles. In all open pit mining and quarrying operations, the power shovel, the transportation equipment, and the primary crushing plant should work as a team, complementing each other. When establishing the design and selecting the equipment for these closely integrated operations, capital and operating costs for each unit operation must be weighed to achieve an optimum balance. Rising labor costs have given impetus to the universal trend toward greater efficiency, higher speed and larger equipment, and higher degrees of automatic control. The result is that power shovels have increased in size, haulage trucks are larger and faster, and only coarse crushers with feed openings adequate to receive run-of-mine lumps of ore with a minimum of secondary blasting are selected for new installations. These coarse crushers also have large through-put capacities, even when adjusted to produce a 6- to 10-in. size of product, thus making it possible to use a single stage of coarse crushing at the average mine. The use of a single crusher results in a compact crushing plant layout consisting of a dumping pocket for receiving loads of run-of-mine ore, a coarse crusher followed by a surge chamber for the crushed product, and a feeder to withdraw the ore at a uniform rate to deposit it on a belt conveyor. A

Jan 1, 1968