Search Documents

By C. P. Mangelsdorf

The success of the Birmingham roof truss (Figure 1) in supporting some difficult roof conditions, particularly in the Illinois coal basin, has given impetus to the development of a number of alternate schemes. These schemes attempt to alleviate two major problems with the Birming-ham truss, namely, the time required for installation and the cost of material. Because of the difficulty of drilling angled holes and the number of different pieces of hardware which must be handled manually, most operators have been unable to install Birmingham trusses in the cycle and have had to schedule truss crews during the maintenance shift or whenever they would not impede production. Due to this delay the truss has traditionally been viewed as a supplemental form of roof support. In fact, the truss might qualify as primary support and replace at least two bolts if it could he installed in the cycle (and MSHA would accept it as an alternate in the roof plan.) [ ] Figure 1. The Birmingham truss. Two attempts to deal with the first difficulty have sought to streamline the truss hardware while preserving the essential character of the Birmingham truss. One of these, by Peabody Coal, is reported elsewhere in these proceedings by C. Bollier. Another is a contract issued by the Bureau of Mines to Bendix Corporation for the development of a machine, particularly suited for use in low coal, which will automate many of the operations currently executed manually. This machine is expected to be ready for field testing by fall of 1982. Once in place, a truss installed by either of these schemes will interact with the roof in the same way as a conventional Birmingham truss. An alternate approach has been proposed by several different manufacturers independently. Although the hardware details differ. the essential idea consists of two angle bolts, the heads of which are connected by a horizontal chord tightened to some pre-determined tension. Figure 2 shows the generalized concept and does not depict any one of the four systems proposed. The advantage of this scheme is that the angle bolts can be installed and tightened in the cycle, and as bolts, immediately satisfy the roof control plan. The horizontal chord can be added later to achieve almost any initial desired roof loading, the limits of which are defined below this scheme is referred to here as the angle-bolt truss. Because of a fundamental difference in the way in which load is transferred between chords, this design does not interact with the roof under subsequent loading in the same manner as a Birmingham truss. The purpose of this paper is to examine this fundamental difference and its consequences. [ ]

Jan 1, 1982

By P. van der Westhuyzen

Gone are the days of stock-standard diamond beneficiation and final recovery circuits that could, with minor modifications, be adapted to treat any diamond-bearing ore source. A new era has dawned, offering the opportunity to streamline existing diamond processing operations or develop simpler, more efficient, and economical diamond processing plants, with the focus on more efficient comminution, beneficiation, and final recovery. This change in scene has been brought about by: ? The introduction, rapid development, and maturation of multiple comminution, sorting, and recovery technologies ? The need to adapt to a new standard of project approach post the commodity super-cycle phase, where optimizing existing operations and developing scalable, ?fit for purpose? new mines are fast becoming the norm in diamond processing plants in both primary and alluvial operations ? The quest for energy efficiency and lower labour costs ? More remote and inaccessible reserves (under lakes, tops of mountains etc.). This paper serves to identify some technology advances and demonstrates how these could be considered as replacements for or in combination with conventional technologies to arrive at an optimum techno-economic solution. To name a few applications/technologies: ? Comminution: conventional cone crusher, modified/specialized cone crusher, and the high-pressure grinding roll (HPGR). Although significant advances have been made in recent years, this paper only briefly covers comminution within the beneficiation circuit design ? Waste sorting: NIR (near-infrared) sorting, optical (colour) sorting, XRF (X-ray fluorescence) ? Primary concentration by combining dense media separation (DMS) with either XRT (X-ray transmissive), pulsed X-ray, jigs, or pan plants depending on the application, scale, and economics ? Final recovery of diamonds with either conventional X-ray technology, pulsed X-ray technology, or XRT. From recent studies, it can be concluded that there is no longer a standard solution, but rather the ?right? or appropriate solution. Through combining a sound knowledge of the ore source (ore dressing studies or onmine data gathering) and leveraging off the advances in technologies, one is able, through trade-off studies, to arrive at the ultimate techno-economic configuration, the ?right? solution. Emphasis is placed on maximizing diamond recoveries through appropriate technology selection and minimizing the associated costs in an effort to de-bottleneck or improve efficiencies of existing diamond processing plants, or to arrive at the ideal new diamond process plant design..

Jan 1, 2014

By Frank R. Cappuccitti

This paper will deal with current market trends for sulfide mineral collectors in three distinct parts; the global market for sulfide collectors, collectors as tools to solve mineral processing problems and new collector Research in the 1990's. The global market and manufacturing of sulfide collectors will be detailed as well as the trend towards using increasing amounts of specialty products. The use of Total Quality Concepts for laboratory and plant evaluations of new products will also be discussed. Research in the 1990's for sulfide collectors will need to focus not on the development of new chemical species but on the application of the new technologies that have already been developed.

Jan 1, 1994

By G. Karahalios

Industrial minerals always play an important part in the technological growth of a country. The extraction and trading of industrial minerals continues to expand, but the industry is now subject to stricter environmental guidelines. This paper presents the current status and growth potential of industrial mineral exploitation in the southeastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, the Former Yugoslav Republic of Macedonia, Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. Annual production figures per country are presented for 1992-1998. These figures are compared to each other, and, where applicable, they are compared to world production figures. The marketing of industrial minerals to Europe and other regions of the world and the effects of such trade on the local economies are also evaluated when such data are available.

Jan 1, 2000

By G. Karahalios

Industrial minerals have always enjoyed an important share in the technological growth of any country in the world. Today, extraction and trading of industrial minerals has expanded, but is also subject to stricter environmental guidelines. This paper presents the current status as well as the growth potential in the exploitation of industrial minerals in the countries of the south eastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, F.Y.R.O.M., Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. More specifically, annual production figures per country are presented for1992-1998. These figures are compared to each other and, where applicable, to world production figures. Trading of industrial minerals from these countries to Europe and the world and its effect to the local economies is also evaluated were such data is available.

Jan 1, 2000

By Robert B. Parsons

"As the 1981 annual reports of Canadian mining companies one by one see the light of day, it becomes clear that softer metal prices and rising costs are the main problems which beset the industry today. These problems are certainly not lightened by that familiar monster lurking in the shadows-taxation! Recent taxation trends in Canada, and the existing tax regimes for the mining industry, continue to be a major bugaboo.This examination by ""Tax Notes"" of the impact of current taxation trends on the mining industry is based on a speech delivered recently by Robert D. Brown, senior tax partner of Price Waterhouse, Canada, to the annual meeting of the American Institute of Mining, Metallurgical and Petroleum Engineers in Dallas.IntroductionThe purpose of this paper is to tell a story-and it is a story with a moral. The first thing to recognize is that, with depressed metal prices and weakening western economies, high taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. However, the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what the future holds for mining men in Canada will equally play an important role in the future development of the Canadian industry. Our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high marginal tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself."

Jan 1, 1982

By Robert D. Brown

The purpose of this paper is to tell a story - and it is a story with a moral. My topic is Present Trends in the Tax Environment Affecting Mineral Development in Canada, and the first thing to recognize is that, with depressed metal prices and weakening western economies, taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. But the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what taxes the industry will face in future years will influence the industry's further growth. My theme today is that, in Canada, our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself. This is a story with some happy parts in it, and, in fact, governments in Canada did learn, haltingly and grudgingly, that there are limits on the amounts that governments could safely extract from the industry, and that some assurances of long term fiscal stability were necessary if investors were to be induced to make massive commitments which could only be recovered over very lengthy periods.

Jan 1, 1982

By A. J. S. Spearing, A. Mueller

The support of intersections in coal mines remains an important safety issue, mainly because the large diagonal span compromises the stability of the roof. This structural weakness is further exacerbated if the intersection is developed incorrectly, the pillar corners fail or the crosscuts are angled (not perpendicular). This report details the current support systems used and investigates unplanned falls of ground in intersections in coal mines throughout the United States. A possible failure mechanism is proposed and some suggestions are made to improve the effectiveness of the support in these vital areas.

Jan 1, 2009

By Dunlop JSF

A description of general mining proced- ures and tyre maintenance practice is given with particular reference to tyre mainten- ance facilities and record keeping at Groote Eylandt. Experience with tyre wear on Wabco 85C rear dump trucks is then outlined, concen- trating on wheel camber, wheel alignment, truck speed, tyre pressure, loading and haul road design. T T.1TUnilhTPTTnAT The Groote Eylandt Mining Company Pty. Limited mines and beneficiates sedimentary manganese ores from a series of orebodies occurring in the western part of the island. The island is one of a group on the western side of the Gulf of Carpentaria, about 50 kilometres from the Arnhem Land coast and about 650 kilometres from Darwin. Whilst capacity of the mine is presently 2.3 mil- lion tonnes of product per annum, current production has been reduced to just more than half this figure, due to a general mar- ket recession.

Jan 1, 1982

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

"To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.INTRODUCTIONCopper is one of the first metals extracted and the main material of choice for different high-technology applications today. Currently 80% of the world's copper comes from copper sulfide ores. However, due to the depletion of high-grade copper ores in the world and constantly growing demand for copper, the need to develop processes and technologies to treat copper resources from additional sources such as mine tailings, low grade deposits, industrial wastes and deposits with high impurity levels such as As and Sb will continue to increase (Miller and Craig, 1983). The beneficiation processes of copper-pyrite ores consisting of tennantite-tetrahedrite series minerals are generally complex. Tetrahedrite-tennantite minerals occur as fine anhedral grains intermixed with grains of galena, sphalerite, chalcopyrite, pyrite and other sulfides (Saharova, 1966). The mineralized zones of Southern Urals, Russia deposits correspond with these ore types but tennantite-tetrahedrite series are more abundant in ores at the Uzelginskoye deposit, some samples of which contain 70% of copper in tennantite form (Seravkin et al., 1994). This deposit differs from other similar copper-pyrite ores by thin mutual ""germinating"" minerals and higher content of arsenic (up to 0.8-1 %) which create additional considerable problems in enrichment (Solozhenkin et al., 2016)."

Jan 1, 2018

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.

Jan 1, 2018

By Kevin G. Stricklin

Introduction Continuous monitoring techniques have been used in the US and abroad for many years. A continuous miner has a monitor that measures methane and automatically gives a warning if the methane exceeds 1%. It deenergizes the continuous mining machine automatically at a maximum concentration of 2%. Main fans are also continually monitored to ensure operation. Alarms may also be given at a remote location should a fan slow or stop. The systems being developed can continuously monitor various gases and equipment throughout the mine and transmit pertinent data to a surface monitoring station. At this station, conditions throughout the mine can be monitored and, in some instances, controlled. These are known as Mine Wide Monitoring Systems (MWMS). History The use of environmental monitoring systems began in 1976 when a federal court approved the petition of modification to use belt air at the face. The first mine to receive a modification did install a system to supplement existing safeguards. Later, the Mine Safety and Health Administration (MSHA) and the US Bureau of Mines (USBM) conducted tests dealing with the use of belt air. Findings from these tests are being used to set guidelines as requirements of a petition. These requirements include: • Velocity of air has to be 0.25 to 1.5 m/sec (50 to 300 fpm); • Monitors will be installed at each belt drive and tailpiece and at intervals not to exceed 610 m (2000 ft); and • An alarm level of 10 ppm, above the ambient level is appropriate. The early uses of environmental monitoring could only be used outby the last open crosscut. That may be a reason for an initial slow growth of these systems. In June 1982, MSHA began evaluating systems that could be used in returns to ensure that monitoring systems being used in areas where permissible equipment is required does not of itself pose an explosion hazard. This is known as the Mine Wide Monitoring Systems Evaluations and Sensor Classification program. The evaluations and classifications granted are based on electric currents and voltages. Use of mine wide monitoring systems The environmental aspect of MWMS in today's coal industry deals with carbon monoxide (CO), methane (CH4), and air velocity. Just as all mines are different and encounter different problems, the MWMS are diverse and can be used to provide necessary data in all areas of coal mines. Mine operators in an ultragassy seam, for example, may be concerned with monitoring methane, while a mine that used diesel equipment may want to continuously monitor for diesel contaminants. In a mine with roof fall problems, airflow monitors may be helpful as an indication of whether the air is flowing in its normal course and at its normal volume. Today's MWMS can monitor any or all of these parameters. Most systems can be expanded as mining needs require. For example, a mine is now being monitored for methane and five years from now CO monitoring would help increase safety. It may be possible to use the same system by adding additional equipment. In the US, 30 environmental monitoring systems were installed from May 1985 through May 1986. In 1984 and 1985, there were 38 and 44 environmental monitoring systems in operation, respectively. Due to mine closings, 11 of these are no longer in use. However, the number of mines using environmental monitoring systems increased to 63. Use of these systems are not limited to any geographic area or

Jan 9, 1987

Earth Sciences: The standard of living of the world's people depends upon human initiative, investigation, and know-how in exploiting the earth's resources. The Earth Sciences-geology, mineralogy, geophysics and geochemistry, meteorology, geography-are basic sciences dealing with those problems concerning the origin, constitution, and utilization of the earth's materials. The development of these fields in one department provides the greatest opportunity for direct contact and stimulus for scientists and teachers working in related fields. In the Earth Sciences, geology and mineralogy are obviously closely related. As rocks are the materials of which the earth is made, so in turn minerals are the constituents of the rocks. Conversely, a study of earth structures and the interplay of physical and chemical forces in the earth is necessary in order to understand the origin and source of minerals. Building on the basic core of knowledge of earth processes, earth structures, and earth history, the geologist will continue to push out the frontiers of stratigraphy, structural geology, pale-biology and petrology with growing insight into principles that control surface and subsurface rock conditions. As the field of geology has advanced, several lines of specialization have developed. The economic geologist

Jan 1, 1950

By M. A. Rodrigues da Silva Enríquez

One of the rare consensual points among different resource-based economic analytical approaches refers to the strategic role of rent from mineral extraction, as a decisive tool to ensure that the temporary wealth generated in the present can turn into permanent income in the future. For this reason, evaluation, distribution and use of mining rent plays a central role in the sustainable development of mining cities. Brazilian legislation provides for this at the municipal level by means of participation in the financial results of mineral extraction accomplished in these municipalities, with the Financial Compensation for Mineral Exploration (CFEM). CFEM is a type of ad valorem royalty, which charges taxes of up to 3% of the net revenue of mineral production. However, legislation does not establish how these resources should be used. Therefore, there is wide variation in the use of CFEM income among Brazilian mining cities. A study from a sample of the 15 largest mining cities in eight Brazilian states made possible identification of two main patterns with regards to the use of CFEM which were labeled "sustained use" and " the pitfall of the single treasury." In that regard, this article discusses the pressuring factors that contribute to these patterns, as well as the institutional arrangements which may be more favorable to inducing more sustained use of CFEM.

Jan 1, 2011

By Jasper D. Ward

The Indiana Limestone Company has developed an insulated, thin and comparatively light-weight pane 1 suitable for use as a spandrel panel in a curtain wall. The panel is about four inches thick and is composed of limestone backed with insulation. The inner surface of the insulation is protected with asbestos-cement board or a metal pan, depending on the type of insulation, building-code requirements and appearance (if the surface is left exposed). The limestone is cut to the size of the spandrel openings and the insulation and backup is applied in the mill ready to be shipped and in- stalled in the wall grid, A mortarless and waterproof joint with the metal frame components is achieved through the use of neoprene, thiokol, and caulking, The limestone is "dirt-proofed" (waterproofed) in the mill to slow down discoloration. The panel weighs more than some presently used materials. However, ILCO's architects and engineers have found that curtain wall systems capable of withstanding imposed wind loads are made up of sections large enough to carry this extra load of stone with little or no modification to the size of the metal frame. Limestone, a traditionally sound material, can be used in this new way without losing any of its natural qualities of dimensional stability, resistance to fire, and permanence.

Jan 1, 1959

By AIME

To be born in the East, reared and educated in the West, to do graduate work in Germany, leading to the doctorate in metallurgy, and to wind up-for the time being at least-in the Middle West as head of one of the outstanding mining and engineering schools of the country, is a unique career. Curtis Laws Wilson, dean (and in most respects, president) of Missouri School of Mines and Metallurgy at Rolla, is a native of Baltimore. He came to Anaconda in 1918 and in due course was graduated from Montana School of Mines, with an exceptional record. In 1921, after experience in metallurgical research at Anaconda, he became instructor in metallurgy at his alma mater. Because of his ability as a teacher, he rose rapidly to head of the department after special work at Columbia in 1923-24. In 1927, Wilson was granted leave of absence to study physical metallurgy under the great Tammen at Goettingen, and returned with his doctorate to his work at Montana School of Mines. His major metallurgical interest was then in age-hardening of copper alloys. Also after his return to Montana Mines, Wilson started

Jan 1, 1948

By Jetson Lemos Ferreira

O presente estudo teve por objetivo verificar a independência tanto da Curva Limite de Tensão (CLT), quanto da Curva Limite de Deformação Plástica Efetiva (CLDPE) em relação à trajetória de deformação. Para tal, foram utilizadas Curvas Limite de Conformação (CLC) de aço livre de intersticiais (Interstitial Free - IF), determinadas, primeiramente, por meio de trajetórias lineares e, posteriormente, por trajetórias bi-lineares estabelecidas por níveis de pré-deformação nos modos de tração uniaxial e estiramento biaxial simétrico. As previsões da CLT e da CLDPE, calculadas a partir das deformações limites da CLC convencional em trajetórias lineares e bi-lineares, mostraram-se independentes em relação à trajetória de deformação. Entretanto, verificou-se que o critério de escoamento adotado tem grande influência na forma e posição destas curvas limites.

Aug 17, 2017

By T. T. Wang, T. H. Huang, S. S. Zhan

"Fractures with diverse features dominate the hydraulic behavior of fractured rocks and are one of the major subjects for hydrogeological characterization of a site. This study investigates curve patterns obtained by packed tests, and as well the influence of fracture features based on 59 sets of in situ packer tests with different fracture combinations and fracture features. The result shows that, in the example of Heshe site, neat and tidy fractures usually provide stable channel for water flow during testing, and the hydraulic properties of fractures infilled with breccia and mud may change during testing because of leaching and/or washed out of infilling breccia and mud. Different combinations of fractures with diverse features in packed test sections lead to different curve patterns for in situ hydrogeological tests. For groundwater flowing predominately through neat and tidy fractures, the pressure-discharge curve of modified Lugeon tests are usually linear curve pattern, and the pressure decrease while the discharge increase in pressure-discharge-time curves of single-hole double packer tests, which benefit statistically determining the transmissivity of dominant fracture sets. INTRODUCTIONFractures interlaced in rock masses are major channels for groundwater flow and generally account for the anisotropic and heterogeneous characteristics of permeability for fracture rocks. To describe reasonably the permeability of a fracture rock, the Discrete Fracture Network (DFN) approach and others with similar ideals have been developed. Many methodologies and associate equipment, for instance, the televiewer and the in situ hydrogeological test, have been proposed to investigate the spatial distribution and the transmissivity for different fracture sets, which are two main parameters necessary for the DFN or similar model simulation (Pearson & Money, 1977; Barker & Black, 1983; Hsieh et al., 1985; Bernard et al., 2006; Quinn et al., 2012). However, diverse outlooks for the pressure-discharge curves and the temporal pressure and associate temporal discharge curves often confuse the investigation results by significant deviations on derived permeability (Houlsby, 1976; Zlotnik, 1994; Royle, 2009; Camilo, 2010).Aiming on technical development for in situ hydrogeological tests and fracture investigation, an experimental well site with 10 wells has been established in Heshe in central Taiwan since 2011 (Wang et al., 2011; Song, 2012; Zhan et al., 2013). Extensive geological survey and well-hole scanning by a televiewer provide spatial distributions and outlooks of fractures in detail. Additionally, a series of Lugeon tests, double packer injection tests and pumping tests have been performed to investigate the permeability of fracture rocks, and dominate fracture sets as well. Based on the results obtained from the Heshe site, this study classifies the curve patterns of hydraulic packer tests. The features of fractures involved in packed sections for packer tests are then inspected in detail. Relationship between the curve patterns of hydraulic packer tests and associated features of corresponding fractures in rock are discussed and addressed accordingly."

Jan 1, 2015

By Allan Rocas, Aswathy Sivaram, Daniel Cressman, Tatiana Chiesa

The City of Toronto plans to construct a 1,350 mm consolidation sewer along the East Don Roadway (EDR). The project includes installation of approximately 260 meter of 1,350 mm diameter concrete pressure pipe through microtunneling methods. The sewer alignment crosses underneath a busy 5-lane arterial road and then follows the very narrow East Don Roadway road allowance. This paper discusses the significant challenges overcome to design the Don Roadway sewer using slurry microtunneling methods through mixed face conditions below the groundwater table in a congested road allowance. A curved microtunnel was ultimately required to avoid conflicts with existing utilities, condominium tiebacks and a bridge structure.

Jun 13, 2023

By R J. Soriano, S Ciutina

The Masbate gold deposits are situated on the island of Masbate, 350 km south of Manila. A new plant was commissioned in April 2009. The grinding circuit consists of one semi-autogenous (SAG) mill Ø9.75 m × 4.27 m, two ball mills Ø5.6 m × 7.1 m and a pebble crushing circuit, which is usually called a SAG-ball mill-crusher configuration. The SAG mill was originally equipped with radial pulp lifters. The mill runs at fixed speed of 10.9 rev/min, which is approximately 80 per cent of critical speed (per cent CS). Due to the high speed of the mill the original radial design pulp lifters presented a high volume of recirculating load inside the chamber and consequently heavy wear on the outer circle (bottom pan).In order to address the high wear on the pulp lifters a number of avenues were considered in early 2011. The chosen solution was to change the geometry of pulp lifters from radial to curved design. The pre-existing drilling pattern on the discharge end of the mill was a major constraint. A number of designs were considered. The selection of the most suitable option was to be made based on 3D discrete element modelling (DEM) and smoothed particle hydrodynamic (SPH) simulations.The original radial design and two potential solutions for curved pulp lifters were simulated with 3D DEM and SPH software. The main three objectives were predicting the charge dynamics, the expected wear patterns and discharge efficiency. One of the solutions was chosen and implemented during 2012.Observations carried on after installation of the curved pulp lifters have confirmed, as expected, a reduction in wear intensity on the outer pulp lifters. In addition to this, at early stages of operation with curved pulp lifters, the mill operator noticed a reduction in energy consumed by the mill with no detrimental effect on mill performance.This paper is intended to further study the effect of curved pulp lifters on mill energy consumption.CITATION:Ciutina, S and Soriano, R J, 2014. Curved pulp lifters – can they save energy?, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 109–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014