Search Documents

By Robert Jakiel

The following paper is being presented to provide a basic understanding of the equipment and procedures used in multi-auger deep soil mixing as part of the program for the Deep Foundations Institute (DFI) Deep Soil Mix Seminar. The paper is written as a summary of the author's experience using multi-auger deep soil mixing equipment while working with SMW Seiko, Inc. on several east coast projects in the United States, particularly the soil-cement mixing for the soil stabilization of the Fort Point Channel area in Boston, Massachusetts, one of the largest and most difficult soil mixing projects completed thus far in the United States. The summary provides a brief summary and insight into some of the operational aspects of the equipment and procedures, and some of the important considerations when using multi-auger deep soil mixing. This paper is intended for use by both the contractor and the designer involved in selecting appropriate soil mixing equipment and procedures for various types of soils, depths or applications, or for a better understanding of the operational aspects, potential benefits, and impacts that the performance criteria may have on the operational capabilities of the soil mix equipment, when specifying multi-auger soil mixing for a particular project. Prior to reading this article it is important to become more familiar with the various acronyms and terminology used in soil mixing technology. A Definitions section has been provided at the end of the paper that will help the reader become more familiar with some of the terms used throughout this paper.

Jan 1, 2001

By Melvin I. Esrig

Lime Cement column stabilization of soft clay and sand in Salt Lake City, Utah and in San Francisco California is described and discussed. Stabilization permitted the construction, in a single stage, of a 14 m MSE wall on "medium" clay in Salt Lake City. It was used to mitigate the potential for liquefaction in San Francisco and to stabilize the Young Bay Mud beneath the BART extension to San Francisco Airport. These applications are described and the field measurements of performance are reported.

Jan 1, 2000

By Bo Westerberg, Mattias Andersson, Yvonne Rogbeck

"Deep stabilisation has been used in Sweden for decades. The method has been improved to allow it to be used in different types of soils and with new binders. One challenging soil type in Sweden is so-called sulphide soil, a fine-grained soil which contains organic material and iron sulphides. There have been some cases in Sweden of problems when using deep stabilisation in this type of soil, and in one case a slope failure occurred. This paper shows that it is possible to achieve good results with deep stabilisation in sulphide soils. Laboratory and field studies from a test site along the Botniabanan railway line in Sweden are presented. Geotechnical and chemical properties of the natural soil were investigated in the laboratory and one or more of these properties may explain the differences in the stabilising effect of sulphide soils. The strength of the laboratory samples and the columns in the field were tested and compared. It is shown that a satisfactory stabilisation effect can be achieved with the proper choice of binder, amount of binder added, curing time and mixing energy. In sulphide soils, more binder additive is needed than in “ordinary” inorganic clays.1. INTRODUCTIONThe term sulphide soils is used in this paper to refer to the unique types of sulphide soil commonly found in the coastal areas along the north-eastern coastline of Sweden between the cities of Gävle and Haparanda, a distance of about 900 km. Sulphide soils are in general very compressible, susceptible to creep deformation and normally show low undrained shear strength. A sulphide soil may have a negative environmental impact through acidification and chemical action if it is subjected to oxygen, for example during excavation or lowering of the ground water table, Mácsik (1999). In foundation engineering works, efforts are made, for environmental or/and economic reasons, to use the sulphide soil as the foundation instead of excavating it. Deep stabilisation by means of columns is a potential method for use when sulphide soil needs to be improved in order to reduce settlements or/and increase the stability of embankments.Sulphide soils were formed as sediments at river mouths and off the coast in the special environment prevailing at the time of sedimentation, Mácsik (1994). The water in which the sulphide soil was sedimented was brackish/sweet and the environment was typically deficient in oxygen. The environment prevented complete decomposition of the organic material in the sediments. As a result, sulphide soils were formed primarily in the form of a fine-grained composition of clay and silt minerals, iron sulphides and organic matter. Such environments still exist today and new sulphide soil sediments continue to be formed."

Jan 1, 2015

By Bezalel C. Haimson

Anna, Ohio, at the junction of Cincinnati, Findlay and Kankakee arches, has been the site of repeated and sometimes damaging earthquakes. As part of a seismicity investigation near-surface (0.15-1 m depth) overcoring strain measurements were conducted in four limestone and dolomite quarries surrounding Anna, the results of which suggest a complicated regional stress pattern, with changes in the maximum horizontal stress direction from N45ºE to N15ºW. Since such abrupt stress fluctuations are rather atypical in the Midwest and since the reliability of near-surface tests in defining regional stress had not been established, we decided to remeasure the stresses at the same locations but at greater depths (0-200 m) using the hydrofracturing method. Owing to the weak horizontal bedding planes of the Silurian shaly limestones and shaly dolomites and the relatively shallow depths, many of the tests yielded horizontal fractures, providing information only on the vertical principal stress (-0.029 MPa/m depth). However, sufficient tests in each of three testholes resulted in vertical hydrofractures to enable the calculation of all three principal stresses. Within 50-170 m depth the horizontal stresses in all three quarries appear to belong to a uniform regional Stress field defined by the following relations: [']Hmin = 5.1 + 0.014 D; [0] Hmax = 10.1 + 0.014 D, where D is depth in meters. The direction of [O]Hmax within 50-170 m depth is uniform at N70°E (±15º). The hydro- fracturing results obtained at Anna, Ohio are in agreement with the prevailing stress regime in the midcontinent both with respect to magnitudes and directions. The results suggest a possible thrust mechanism for a proposed NW-SE fault along which most of the earthquake epicenters have been located, and a left lateral strike-slip at greater depths. The focal mechanism solution of a recent major earthquake near Sharpsburg, Kentucky, some 200 km south of Anna, also indicates strike-

Jan 1, 1982

By R. M. Clowes

Lithoprobe is a collaborative, multidisciplinary research project which is providing new insights into the tectonic evolution of the North American continent through its work within ten study areas across Canada. For the mining industry, such results provide a well-constrained regional framework and better understanding of tectonic processes which lead to the development of ore deposits. In mining camps, seismic reflection methods have proven effective in imaging shallow to moderately dipping litho logic contacts as well as structural features, and in some cases have been used for the direct detection of ore bodies. Here, short case histories are provided for the Abitibi greenstone belt (VMS deposits) in Quebec and the Thompson nickel belt in Manitoba.

Jan 1, 1999

By J. Chai

In order to find the behavior of dewatered unconsolidated strata during the process of injecting water through a borehole, a new type of fiber Bragg grating (FBG) sensing system was successfully used for the real-time strain monitoring of unconsolidated strata during a water injection process for a dewatered unconsolidated strata of a coal mine. The unconsolidated strata water injection test was implemented through a borehole at a depth of +115.83 to +135.15m. The employed FBG strain monitoring system and ground water level observation system were installed at the depth in the unconsolidated strata where the water injection was conducted through two different boreholes. The water injection pressures in the test were 0.1, 0.2, 0.3MPa respectively, and the total water injection volume was 4226.84m3. The relationships between the water injection pressures, water injection volume and the strain change of the unconsolidated strata, the stress and strain conditions of the unconsolidated strata before and after water injection, were analyzed. This paper presents the results of these tests, and shows that the dewatering compression of the unconsolidated strata is reduced with increasing water injection pressures and water injection volumes. Comparing the stress-strain conditions before and after water injection, it is found that the stress of the water injection strata is in tension, which confirms the theory that the settlement of the thick unconsolidated strata is directly caused by the reduction of ground water levels. The high sensitivity and stability of the FBG monitoring system used was able to realize the real-time strain monitoring of the water injection process within a deep unconsolidated strata. This FBG monitoring system and the test results presented are very important for understanding further treatment of settlement in unconsolidated strata.

Jan 1, 2012

By P. Ventura

Reliability of the liquefaction analysis is based on data plotted as by piezocone, as by deep vibrocompactation monitored tests. The negative porewater pressure, re lated to hydrostatic value, recorded by piezocone, is a good marker of the absen ce of the liquefaction. Systematic measures of the ground settlements, inside the vibroinfixed steel pipe, allow to locate the liquefable strata with loose density. Experimental study of the combined soil improvement by stone columns is carry out in particular in sea bed. The interaxis of the columns for the best efficiency is valued as of the vibrocompactation, as of the drainage effects, especially during earthquake.

Jan 1, 1989

By Roberto Folchi, Hans Wallin

Lake Mead, the largest man-made reservoir in the United States, is located about 30 miles southeast of Las Vegas, Nevada. For the construction of Lake Mead third water intake, which is entirely placed underground, an underwater excavation was needed at a depth of 100 m (330 ft): a large surface had to be deepened by 20 m (66 ft) in basalt.

Jan 1, 2012

By Salvatore] [Parand

Deep well disposal is a much used and abused term which is the panacea for wastewater disposal in some minds and creates near hysteria in others. It can be the answer to a difficult waste disposal problem, or if improperly employed, can create more problems than it solves. My purpose in this presentation is to focus on the value and limitations of deep well disposal as expressed by New York State's experience and policies. To he sure, I feel a place for such practices docs exist if adequate safeguards are utilized. I shall give a broad brush approach to New York's legislative, geologic and operational concerns and speak briefly on some case histories. I shall not delve deeply into the technological details since I am not an expert in mining exploration or well drilling.

Jan 1, 1973

By W. A. Steingraber

This paper discusses the application of deep well disposal techniques to the problem of disposing of large volumes of low level radioactive wastewaters generated by the in situ uranium mining industry in Seth Texas. Data is presented on wastewater composition and volumes, geologic and hydrologic parameters of the disposal reservoirs, tell construction techniques, well operation, well monitoring requirements, and critical factors in evaluating the Safety and environmental impact of a deep injection well system.

Jan 1, 1980

The association of deep well turbine type pumps with metal mining is by no means a new one, though undoubtedly each application has certain features of interest, conformable with attendant circumstances. Although all conditions pertaining to a particular operation in one mine are rarely, if ever, duplicated in another mine, it is felt that some aspects will be parallel, or in various ways comparable.Therefore the following descriptions of an installation of a deep well turbine pump as part of dewatering plant in connection with shaft sinking may be of general interest to metal mine operators.The Man and Supply shaft at Mount Isa Mines is designed as shown in plan by Fig. 1. It is the main entrance and service shaft for the entire property and hence is in constant use. Arrangements for sinking must be such as to cause little or no impediment to routinehoisting work. Also, being the main shaft, it has been essential to deepen it in step with successive level developments.During the period of operations at Mount Isa only a limited time has been available to complete succeeding levels down to the present No. 7 haulage level (895 ft.), and sinking operations in soft, broken, leached, and heavy water-bearing country have presented many features militating against reasonable speed and cost. Outstanding among these difficulties has been the large volume of water contained in the pervious brecciated country.

Jan 1, 1939

By Hallan Marsh

THE subject of this paper is apt to bring to mind wells ranging from 6000 to over 8000 ft. in depth. However, it is uncommon to pump wells at depths greater than about 5000 ft. Fig. 1 shows the number of wells being pumped at various depths by one company in Southern California. FIG. 1.-NUMBER OF WELLS BEING PUMPED BY ONE COMPANY FROM VARIOUS DEPTHS IN SOUTHERN CALIFORNIA. A few companies have a very few wells pumping at depths greater than this. This paper will deal with wells between 3000 and 5500 ft. in depth. Most California oils at these depths are between 25° and 35 gravity. The subject is so broad that it will be necessary to omit many interesting phases, and to treat others very briefly. Power, power transmission equipment, power efficiency, counterbalancing, sucker rods, pumps and volumetric efficiency will be discussed.

Jan 1, 1928

This paper addresses, in particular, the influence of winding depth on the selection of head ropes for Koepe winders. Because this is just one aspect of winder design that affects the operational safety of the winding system, the paper starts by considering all the issues governing the life and safety of the winding ropes. Regulations from a variety of countries are reviewed and comparisons of the legislated rope factors of safety and their variation with winding depth are made. This is followed by a discussion of the typical observed mode of in-service deterioration of Koepe head ropes. This mode of deterioration is due to fatigue and is influenced by the load range occurring in the ropes. Parameters contributing to load range are discussed and the influence of winding depth is highlighted. Lessons learned from early experience with very deep Koepe winders in South Africa are recalled. Predictions of load range as a function of depth are made, from which general rope life predictions are made for ropes selected by conventional national factor of safety requirements. This is illustrated in graphs comparing rope life as a function of depth. Typically a reducing life with depth is predicted. A rope selection strategy is advocated, which is based on achieving a constant rope life irrespective of the depth of wind. A new factor of safety (or rope design factor) equation is prepared that has the trend of increasing with depth. This proposed equation is compared with other published proposals that promote an increasing rope factor of safety with depth. It is shown that smoother winder drive controls enhance winding rope life and this improvement is quantified. The paper concludes by pointing out the consistency in predicted and observed life of winding ropes selected in accordance with legislated factor of safety approaches. It recommends the adoption of a new rope design factor equation for rope selection, to be used in conjunction with appropriate codes of practice for winding rope condition assessment and for the design, installation, operation, maintenance and testing of Koepe winders. The new rope design factor equation approaches a limiting economic depth of wind at shallower depths than the existing Koepe factor of safety approaches. However these older approaches æbuild-inÆ a reducing rope life with depth. The new rope design factor is therefore a more consistent way to select Koepe ropes and to evaluate economic trade-offs between Koepe and conventional double-drum or Blair winding systems.

Jan 1, 2005

By Yvone Franco Crosato

The dense population of Hong Kong requires the construction of tall buildings in reclaimed areas or perched on the slopes of the many hills. The large loads to be supported are carried by deep foundations. Many of those are bored piles, to rock, of diameters up to the 3.0 m. of today.

Jan 1, 2000

By Chas Dobbel

THE Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. 1 mine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present.. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great. margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the wear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was usd to drive prospect holes with jointed steel.

Jan 9, 1925

By Xuejing Xie

Exploration geochemistry for many years has been very effective in searching for mineral deposits covered by residual overburden or blind ore bodies hosted in pre-ore rocks. It has not been as effective discovering ore bodies deeply concealed under various kinds of transported overburden or post-ore sedimentary and volcanic rocks. From the 1980s to 1990s, various types of new geochemical techniques with the ability of deep-penetration through exotic covers have been developed. The concepts and methodology of deeppenetrating geochemistry are evolving from partial extraction and gas surveys prevailing from the 1950s up to now, but there are intrinsic differences. Most of the new deep-penetrating methods are used in detailed surveys to delineate deeply concealed ore bodies which could not be ascertained by conventional geological, geophysical and geochemical surveys. In this sense, the sampling and analytical methods of Nameg and Momeo are described briefly. Experiments of such strategic deep-penetrating geochemical surveys have been carried out in desert, alluvium, steppe and laterite covered terrains in China, Australia and Uzbekstan.

Apr 24, 2001

By Nobuyuki Okamoto

The 21-year long-term Japan-SOPAC Cooperative Deep-sea Mineral Resources Study Programme was completed in March 2006. The Programme, which commenced in 1985, has seen numerous marine research surveys being conducted within the Exclusive Economic Zones (EEZs) of 12 SOPAC member countries (Figure 1). The various research and government institutions that have been closely involved in this longstanding Programme include: the Japan International Cooperation Agency (JICA); Japan Oil, Gas and Metals National Corporation (JOGMEC) (formerly, the Metal Mining Agency of Japan, MMAJ) and relevant ministries of the participating Pacific Island governments.

Sep 24, 2006

By Claudio Flores Martinez

The prospect of accomplishing economically and scientifically profitable deep-sea mineral mining within this decade or the next one is of particular interest to the emerging discipline of astrobiology which is concerned with the origin, distribution and future of life in the Universe. Several planetary bodies within our own Solar System such as Jupiter’s moon Europa and Saturn’s Enceladus now appear to be potentially habitable, or life-friendly, in terms of the three prerequisites for life as we know it: a sustained body of liquid water, biogenic elements (C, H, N, O, P, S) and energy sources to fuel metabolic reactions. Europa, for instance, possesses a global subsurface ocean, believed to be up to 100 km in depth, hidden beneath a kilometer-wide ice-sheet. A silicate mantle is directly interacting with a cold, aphotic ocean in which tidal forces might drive geological seafloor activity that results in the creation of hydrothermal systems. These locales are commonly hypothesized to be the cradles for an alternate origin of life on Europa. Especially alkaline hydrothermal springs, as found at Lost City, have been at the center of modeling the prebiological evolutionary dynamics preceding cellular life. Serpentinization-like reactions are also possibly fueling metabolic networks in putative microbial communities found in the oceans of the icy moos. Major space agencies around the globe are planning future space missions aimed at exploring and eventually characterizing potential life forms in these habitats. The technology needed for this exploration effort resembles the requirements for a successful deep-sea mineral mining industry: highly efficient AUVs (also equipped with biologically-oriented instrumentation), swarm robotics, landers, seafloor rovers and general high-pressure, cold temperature extreme environment engineering. Interestingly, science questions of deep-sea mineral mining and astrobiology converge too: the hypothesis of life originating at hydrothermal systems, the biogeographical distribution of species among these environments, adaptations of extremophilic organisms across the three domains of life and adequate autonomous robotic systems to assess the complexity of deep-sea biological communities. This presentation attempts to present a two-fold view of advanced planetary exploration that relates to a sustainable vision of deep-sea mineral mining: charting our oceans and developing technologies least harmful to endemic biology can propel the design and prototyping of future robotic planetary probes bound for aquatic missions on alien moons. Space industry, government and public interest towards a broadened planetary perspective on deep-sea mineral mining is promoted by addressing an astrobiological rationale of this endeavor.

Sep 1, 2014

By W Midgley, M Torok, I Canbulat, J Katupitiya, S Saydam, S Akdag

The green energy transition is expected to require a range of valuable minerals, which could be supplied through deep-sea polymetallic nodule mining. Deep-sea polymetallic nodules are mineral deposits with a composition well suited to produce lithium batteries, which are expected to be a necessary energy storage solution (Diouf and Pode, 2015; Paulikas et al, 2020) for the energy transition. By 2050 the annual demand for both cobalt and lithium is estimated to increase by around 450 per cent from 2018 levels (Hund et al, 2023), with the annual demand for nickel being greater than 2 million tons, and copper greater than 1 million tons. Polymetallic nodule mining is well positioned to provide these minerals in the near future. An intricate and comparatively unexplored ecosystem thrives within and surrounding the nodule fields (Smith et al, 2008). Deep-sea mining operations have the potential to disrupt and permanently damage this ecosystem through introduced pollution, artificial noise and light, and habitat destruction. Hence, there is a pressing need for new engineering and scientific endeavours to focus on developing new technologies to reduce any environmental impact from mining.

Sep 1, 2024

By Andrea Koschinsky, Luise Heinrich

(for an oral presentation) Activities for preparing future deep-sea mining offer the unique opportunity to study environmental conditions and anticipate adverse environmental impacts prior to the commercialization of the activity. Until know, environmental research has first and foremost focused on understanding direct impacts occurring at the seafloor or in the water column such as the removal of substrate, the suspension of sediment or the creation of particle plumes. Impacts occurring above the sea surface have thus far rarely been considered. The operation of deep-sea mining equipment, as well as of mining and transport vessels will be associated with a considerable energy demand. In the open ocean, this energy will be provided by heavy fuel oil (HFO), which is the cheapest and most common marine fuel. The combustion of HFO will be associated with the release of greenhouse gases and other pollutants. Deep-sea mining will thus directly add to already critical air pollution levels caused by international shipping. To contribute to a holistic assessment of deep-sea mining impacts and to address the previously outlined knowledge gap, we present the methodology to quantify the fuel consumption and associated emissions of a potential typical commercial manganese nodule mining operation in the Clarion-Clipperton Zone (Fig.1). Using the mine set up and energy demand estimates from a study commissioned by the German Federal Ministry of Economic Affairs and Energy supplemented by information from literature, we anticipate emissions of carbon dioxide (CO2), carbon monoxide (CO), methane (CH4), nitrous oxide (NO2), nitrogen oxides (NOx), sulfur oxides (SOx), particulate matter and non-methane volatile organic compounds.

Jan 1, 2018