Search Documents

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By Jon Hurt

INTRODUCTION The entire scope of new facilities for Lake Mead Intake No. 3 includes a sub-merged intake structure, a deep tunnel beneath Lake Mead, a tunnel access shaft, Intake Pumping Station No. 3, and connections to an existing intake and water treat-ment facility, as shown in Figure 1. In March 2008 Vegas Tunnel Constructors (VTC), a joint venture of Impregilo SpA and SA Healy were awarded a $447m Design-Build contract by SNWA for a section of this work (Contract 070F 01 C1), including the 185 m deep tunnel access shaft, the 4.7 km long, 6.1 m diameter tunnel and the submerged intake. Arup, supported by Brierley Associates, is the Design Engineer for VTC. The scope of the work is shown in Figure 2. This paper will describe the design and construction on this contract, with a focus on the access shaft which is the most complete section of the work. The shaft is being sunk using drill-and-blast methods with the finallining placed as excavation proceeds. The shaft passes through a major fault zone, and extensive pre-excavation grouting for water control is required for much of the depth of the shaft.

By B Chapman, B Gaida, L Drowley

The 372 MW Ulu Jelai Hydroelectric Project is a peaking power scheme located in the Cameron Highlands, Malaysia. The main features of the project include an 84 m high roller compacted concrete dam; two weirs which divert flows from adjacent catchments via transfer tunnels into the main reservoir; an underground power waterway; and an underground power station complex comprising three large caverns with connecting tunnels approximately 240 m below surface level. The project includes approximately 25 km of tunnels excavated in fresh granite rock mass with some distinct shear zones of weaker material. The majority of the tunnels are being excavated using drill and blast, with the two transfer tunnels being excavated with a tunnel boring machine (TBM).This paper focuses on the design and construction of the Telanok underground power station complex and also some aspects of the design for the headrace tunnel. Topics covered include geological site investigations including in situ measurements of rock stresses; development of a geological model and parameters for rock support design; three-dimensional modelling to assess interactions between the caverns to optimise rock support; design of a rock anchored crane beam; construction of the caverns and design of the unlined headrace tunnel taking into account hydraulic jacking and operational pressure fluctuations.CITATION:Drowley, L, Gaida, B and Chapman, B, 2014. Design and construction of large caverns in granite – Ulu Jelai Hydroelectric Project, Malaysia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Andrew Peterson

The Maine Department of Transportation offered this challenging design-build project for a new, 12-span, bridge over the Kennebec River in Bath, Maine. This structure would be built to replace the existing Carlton Bridge connecting the village of Bath, Maine to neighboring Woolwich, Maine. The design build team of Flatiron Structures, Inc., and Figg Engineers, Inc., elected to design and build a segmental concrete bridge. Site conditions dictated that this bridge would be supported primarily on deep foundations. Case Foundation Company joined the project team in the winter of 1997 to install twenty-two, eight foot diameter drilled shafts. The drilled shafts were designed with 8' diameter, permanently cased shaft sections and 7.5' diameter rock sockets. Shaft lengths ranged from 20' long near the river's edge to 100' deep in the middle of the river. Rock socket lengths ranged from 12' to 30' deep. Two Osterberg Cell load tests were conducted on production drilled shafts. Figg Engineers utilized the results of the load tests to "fine-tune" the rock socket design during construction of the drilled shafts. Construction of the drilled shafts proved to be very challenging and called on every member of the design-build team to work together throughout the project. One of the most challenging aspects of this project was in the installation of the 8' diameter permanent casing and drilling of the rock sockets. Early in the project, it became apparent that the top of bedrock was broken and unstable. This condition limited the advancement of the permanent casing and the affect of a "seal" at the top of rock socket. As a result, as the rock socket was advanced, loose material spilled into the hole and stopped progress of the socket. In order to resolve this problem, the design-build team developed a redesigned drilled shaft which included the installation of a steel sleeve to seal off the unstable rock formation. Following installation of the sleeve, the rock socket diameter was reduced to 7' diameter and advanced additional length to achieve required design capacity. All drilled shafts were installed with equipment supported on floating barges. Water access, along with the long shaft lengths and very hard bedrock required the use of cranes and drilling equipment that far exceeded the requirements of typical drilled shaft projects. This paper will discuss the relationship between design, construction, and equipment utilization on this challenging design-build project. [ ]

Jan 1, 1999

By M. Trim, Y. Sun, D. Tepavac, A. Kumar

Configuration of Rozelle Interchange Project’s ventilation system required design and construction of some of the largest and tallest underground civil caverns attempted in Australia. The paper focuses on the technical challenges of designing these caverns within a heterogeneous, generally weak sandstone under highstress conditions while providing a construction sequence that would align with the contractor’s preferred techniques and schedule. Various construction techniques were investigated, but ultimately an observational approach relying on a construction sequence and specialized instrumentation met both the designer’s and contractor’s requirements. Relevant data obtained from excavations and the construction monitoring program are presented within.

Dec 1, 2022

By Julio C. Martinez, Jeffrey L. Rice, Hayden Weschler

This paper details the extensive underpinning required to hold up the 39th street Bridge while demolishing its massive support piers and building a 30ft deep Cut/ Cover RR tunnel beneath it. The underpinning/SOE support required the construction of 16 large hand dug pits 36ft deep that were reinforced and concrete filled. In addition, an extensive steel support system was tied into the bridge super structure. All of the underpinning/tunnel construction was done while a 110ton crane sat directly atop the heavily trafficked – 66 ft. wide bridge. The tunnel excavation, concrete lining and final bridge pier support work will also be presented. All work was done within 5ft of active mainline tracks and that required tight grouting behind all lagging to eliminate any track settlement.

Jun 13, 2021

By Michael Francis, Chris Darton

More than 55 km of tunnels have been constructed by TBM in the last 12 years to refurbish and upgrade the high voltage cable network in London. These include a tunnel of 20km length using EPBM machines in both clay and granular soils. Route selection was made with reference to subsurface structures, existing ground conditions, using suitable shaft locations addressing environmental concerns. The complex interfaces to manage included obtaining of consents to the coordination of multiple suppliers. The paper describes how all these challenges have been met successfully and how technology has been employed to provide for safe construction and operation in the congested urban environment.

Jan 1, 2003

By Michel Claisse, R. P. Goel, André J. Rancourt, Kent Murphy

The Malana Hydroelectric Project is a private development located in HimachalPradesh State, India that was commissioned in June 2001. The plant was built and is owned by the Malana Power Company, a subsidiary of the Bhilwara Group of New Delhi. With a total head of 400 m and nominal capacity of 86 MW, the plant is capable of generating 360 GWh annually. The 3,1 km long, 4,0 m diameter power tunnel was designed to be excavated by conventional drill and blast methods. Contrary to traditional practice in India for pressure tunnels of providing a concrete lining, the Malana tunnel was finished mainly with shotcrete. In this way, the tunnel was completed in a period of18 months, a record for recent projects in the Himalayas, and at a cost substantially below that of conventionally lined tunnels. An interesting aspect of the project was the design of the steel tunnel liner linking the power tunnel to the penstock. The length of the liner was fixed finally on the basis of in-situ testing using both hydraulic jacking and doorstopper tests to evaluate the ability of the rock to withstand the internal pressure of4,0 MPa that exist near the downstream end of the tunnel.

Jan 1, 2003

By Andrew Baxter

The Crystal Bridges Museum of American Art in Bentonville, Arkansas is a beautiful glass and concrete structure cut into a valley that mingles with water ponds spanned by multiple bridges with suspended roofs. Or, at least it will be when completed in 2009. At Crystal Bridges, most of the proposed buildings involve cuts up to 50 ft high to be retained by the building structures. This requires the construction of retaining walls adequately founded to support lateral loads of up to 70 kip/ft. To add to this difficulty, the site is within a karst region with all the variability and irregularities associated with solutioning and erosion of the parent rock in this environment. The irregular rock profile made it virtually impossible to conceive a predictable arrangement of shallow footings and shear keys for the retaining walls. The existence of layers of soft soils within a hard rock formation made a caisson foundation impractical. The authors developed an innovative solution based on micropiles, which proved to be invaluable from a cost and schedule point of view. In areas where rock was shallow, micropiles were used as ?shear pins? to transfer the horizontal loads to the rock. In areas with significant overburden, a system of vertical and battered micropiles was devised to carry vertical and horizontal loads from the retaining walls. This paper presents a detailed description of the design and installation of the micropiles used as shear pins, and includes the results of lateral load tests performed on full-scale models of the grade beams on shear pins. The work performed shows that micropiles in rock can be effectively utilized for support of significant lateral loads provided that an adequate arrangement of suitably sized micropiles is provided, and that micropiles used as shear pins may develop significant tensile stresses when loaded laterally.

Jan 1, 2008

By A. J. Williams

"Whenever a decision is made to bring a mineral deposit into production, the Owner in actual fact has decided to convert substantial sums of capital into productive capacity with the intenti6n of making a profit from such conversion.Escalating costs of construction, frustrating and costly delays in comp1etion, the increasing tempo of technological change and the increasing size and complexity of mineral processing projects have convinced Owners that the best way of implementing their capital must be sought and utilized. This requirement has stimulated a search for ways and means of applying modern management techniques to the design and construction of mineral processing plants.This search by consulting firms has resulted in the evolution of the concept of project management and the development of planning and con trolling techniques with the result that Owners can seek and obtain better assurance that their project objectives will be fulfilled.This paper will attempt to outline how a mineral processing plant can be brought into production through the implementation of project management techniques.Definition And Objectives Of Project ManagementThe design and construction of mineral processing plants is subject to the restraints of three inter-related parameters -Quality, Cost and Time each of which influences and is influenced by the other two.Project management is a technique where the Owner delegates complete responsibility to a single organization for all phases of a project (design, procurement, construction and commissioning) for the above parameters but retains freedom for major decision making. Normally, the consultant under-takes full responsibility for all phases, but partial project management services can be provided when the Owner so desires.The objective of project management is first to devise and define and then to implement a program in which the relationship between the three parameters of Quality, Cost and Time is optimized, i.e., the desired functional and other requirements are attained (but not exceeded) at the lowest practicable overall cost in the shortest practicable time. The measure of success of a project lies in the degree to which this objective is achieved."

Jan 1, 1974

By C. Y. Kao, Roger Y. Cheng, C. S. Hsieh

The mushroom-shaped Minghu power cavern located in central Taiwan is 21.2 m (W) by 40.5 m (H) by 127.2 m (L) and is designed to house 4 units of power generating-pumping equipment with a total capacity of 1,000 MW. This paper presents an introduction to the geological conditions at the cavern site; the rock mechanical tests undertaken; the design approach adopted; the construction method and sequence followed; and the instrumentation provided in the roof arch to monitor the behavior of the surrounding rocks. The measured data collected from the embedded instruments will be compared with those obtained from theoretical analyses and presented in this paper. Several technical problems encountered during the construction stage are covered and the solutions of these problems are also described therein.

Jan 1, 1983

By Juan M. Pestana, Jeremy M. Gasser, Cuneyt Gokmen, Paul J. Sabatini, William Tanner, Daniel J. Woeste

An access pathway and working platform were designed and constructed for equipment access for a Deep Soil Mixing (DSM) pilot study over a coal combustion residual (CCR) surface impoundment (SI). The DSM pilot study was conducted to evaluate slurry mix designs and construction techniques for installing DSM columns up to 95 feet deep. Two-dimensional (2-D) limit equilibrium and 2-D finite element analyses were used to evaluate multiple failure mechanisms including: (i) bearing capacity, (ii) punching shear of mixed ground and underlying CCR, (iii) effect of fluidized DSM columns on working platform stability, and (iv) liquefaction. The analysis results were used to design ground improvement required to increase bearing capacity and stability of the CCR under the proposed equipment access route. A long-reach excavator was used to perform shallow bucket mixing and walk onto the CCR SI atop previously mixed cells following a minimum cure time and acceptance of quality control test results. Prior to mobilizing the DSM rig, a static load test was conducted to evaluate performance of the working platform. Both the access pathway and working platform demonstrated acceptable performance under the design loads during the DSM pilot study. This case study emphasizes the economic and safety benefits that can be realized by appropriately designing critical temporary work items such as access pathways and working platforms in difficult ground conditions. INTRODUCTION A Deep Soil Mixing (DSM) pilot study was conducted at a coal combustion residual (CCR) surface impoundment (SI) to evaluate slurry mix designs and construction techniques for closure design of the SI (Site). Sluicing of CCR at the facility ceased and closure will be initiated based on requirements in the final United States Environmental Protection Agency (USEPA) Rule for Disposal of Coal Combustion Residuals from Electric Utilities, 40 CFR 257, effective October 19, 2015. The proposed closure approach involves constructing a DSM containment structure (DSM Wall) to separate the SI into two areas: (i) a closure by removal area; and (ii) a consolidate and cap-in-place area. The proposed DSM Wall would retain the CCR within the consolidated closure footprint and provide a barrier between the two areas of the SI. The predominant CCR in the SI where the pilot study was conducted were fly ash and bottom ash. CCR materials in surface impoundments are generally soft and saturated as a result of being sluiced into place and can present stability and safety challenges when performing earthwork activities.

Jan 1, 2019

By B. W. Snyder

INTRODUCTORY THE earliest known case of transmission of natural gas by pipe lines was early in the Christian era when the Chinese used bamboo pipes to transport natural gas from surface seepages to heat brine for the recovery of salt. Since that time many materials have been used as conduits-hollow wooden legs, wood stave pipe, day tile, cast iron, and, finally -since about 130 years ago - steel pipe. Even then, this new material came into use rather . slowly for, as recently as 80 years ago, wood pipe was still being used. However, as techniques were developed to take advantage of the properties of steel, this material gradually replaced all ethers for the transportation of gas for longer and longer distances at ever increasing pressures. In 1912, one of the longest pipe lines of its size at that time was built-this was a 16-inch line bringing gas from Bow Island to Calgary, a distance of 170 miles. We have been able to find records of only two ether such lines at that time-one a 185-mile 16-inch line from Vivian, Louisiana, to Little Rock, Arkansas, completed in the summer of 1911, the ether a 280-mile line from West Virginia to Toledo, Ohio. This last ? mentioned line was reported in a magazine article of September, 1912, but no indication was given of its size on completion date. It is apparent, therefore, that modern high pressure transmission of natural gas is a technique less than forty years old.

Jan 1, 1951

By Timothy O’Rourke, Karrie Buxton, Chris Lynagh, Daniel Dobbels, Frederick Vincent

The Doan Valley Storage Tunnel Project in Cleveland Ohio was constructed to control Combined Sewer Overflows (CSOs). It is a complex system of three tunnels ranging from 8.5 to 18 feet in diameter with a total length of about 2.3 miles that was put into operation in mid-2021. The project lies within and below the cultural, educational, and medical hub of Cleveland, which presented unique design and construction challenges. This paper provides a case history of the design and construction, with particular attention given to lessons learned in devising a large tunnel system that can carry both dry and wet weather flows constructed in rock with limited cover, within a flood plain area and vibrant urban center

Dec 1, 2022

By West Coast Staff

Attention to the design of facilities for drainage, of both surface water and seepage, made it possible to attain, for a qam impounding residues from a concentrating mill, a more stable sand wall which can eventually be carried to a greater height.EXPERIENCE WITH No. 1 DAMResidue from the lead zinc concentrating mill, which treats the ore from the Rosebery and Hercules Mines, was pumped 3,600 ft. through a 5-in. diameter woodstave pipeline to the site of the dam. It was formerly delivered through a 4-in. steel pipeline.State laws prevent the residue being discharged to waste into the Stitt River. Furthermore, as a pyritic residue it is a potential source of sulphur.Between 1936 and 1956 more than 1,000,000 tons. of residue was paddocked. The run-of-mill product was roughly classified at the dam in a 6-ft. diameter cone classifier and the sand fraction was pumped by a 3-in. pump to the front wall of the dam across a shallow valley. The overflow gravitated to the rear of the dam (Fig. 1). Typical sizings were:

Jan 1, 1958

By Gerald G. Griswold, Allan G. Provost

INTRODUCTION The Norad Expansion Project was located 10 miles southwest of Colorado Springs, Colorado, within Cheyenne Mountain. The expansion areas to be excavated would be adjacent to the existing underground Norad complex, which would remain in operation during the work on the expansion. The original complex had been constructed approximately eight years earlier and had been in full operation for approximately five years. Phase I, Excavation was awarded the Tiro Construction Corporation, a subsidiary of Harrison Western Corporation, Denver, Colorado, in the fall of 1970. Notice to Proceed was given to Tiro on 28 December 1970. The project owner was the U. S. Air Force, design was performed by the U. S. Corps of Engineers, Omaha District, who would also serve as the construction agency. [ ]

Jan 1, 1979

By Jørn Thomsen, Christoffer Brodbaek

"As governments increasingly accord high priority to sustainable energy, policymakers are finding that wind energy has a long track record as a proven alternative to conventional energy supply.Over the past two decades, wind turbine projects have been constructed offshore because of more stable offshore wind conditions and because there is more available space for large wind farms out in the open sea. Vindeby Wind Farm in southern Denmark was constructed in 1991. As the world’s first offshore wind farm, it provided valuable information and experience for researchers and designers that have led to new technologies and design improvements, a trend that will continue as more offshore wind farms are constructed. Today, the world’s capacity of the installed offshore wind turbines exceeds 1,000 MW. Most of these are installed in Northern Europe where there was early political support and favorable conditions, such as strong winds and relatively shallow waters. Offshore wind projects are now under development around the globe, including continental Europe, the U.K. and North America. ‘The largest offshore wind farm today is Denmark’s Nysted Offshore Wind Farm, which has a total capacity of approximately 480,000 MWh, equivalent to the yearly consumption of 120,000 households. It is five to six miles offshore in the Baltic Sea in the southern part of Denmark.The owner is a joint venture between DONG Energy of Denmark and E.ON Sweden. Bonus Energy (now Siemens) supplied the wind turbines, and P. Aarsleff A/S and subcontractors supplied the foundations. The contractor’s consultant, COWI A/S of Denmark, developed and designed the turbine foundations. With a total capacity of 165.6 MW, the project consists of 72 Bonus 2.3 MW turbines in water depths up to 33 ft. The turbines have a hub height of 226 ft, and the turbine blade diameter is 270 ft. The rotor and nacelle (the structure that houses the generator, gearbox and other equipment) weigh approximately 150 tons, and the weight of the steel tower is approximately 130 tons. The wind farm site is located in a relatively protected area of the Baltic Sea, but during the winter months, the water often freezes and the foundations needed to be constructed to resist ice forces. The founding soils at the site are overconsolidated clay tills with boulders and with a thin layer of softer surface sediments. Pockets of up to 30 ft of soft sediments were encountered, which required special foundation preparations."

Jan 1, 2009

By Dempsey S. Thieman

The Kuparuk River Central Channel Bridge on the North Slope of Alaska provides critical access for oilfield service vehicles in the largest oilfield in the United States. The original sloped spill-through bridge abutments were protected by articulated concrete revetment. After 27 years of heavy service, ice impact, deep river scour, and high floods, the revetment required replacement. An OPEN CELL SHEET PILE® abutment was selected to replace the existing erosion protection and provide increased performance and structure life. Project engineers and contractors successfully addressed the challenges of low overhead sheet pile installation under the bridge, extremely heavy vehicle loads, and arctic winter construction conditions through innovative design and construction techniques. The project was successfully completed on schedule with minimal disruptions to critical bridge traffic. This paper provides a detailed discussion of the design and construction techniques utilized to address the challenges of the project, many of which could be adapted to other projects.

Jan 1, 2008

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019

By Nasr Sheta

"After Hurricane Sandy, the stability of an earth slope in the Atlantic Highlands, New Jersey in the United States was deteriorating due to slumping soils and erosion from flooding. A slope stability evaluation indicated the slope did not satisfy the requirements of the local building code. A triple-tier, pile-supported and mechanically stabilized earth wall was designed and constructed to stabilize the slope. The construction was planned from a 3-m-wide roadway and, because of rough terrain and limited work space at the site, a cast-in-place drilled-pile construction was deemed impractical due to slow pile production. An alternative procedure was utilized by pre-drilling holes, and installing precast tip-and-shaft-grouted (PCTSG) piles, which extended to competent soils to improve slope stability. A grade beam, connecting the PCTSG piles along with soldier beams and concrete lagging were used to form the lowest tier of the slope stabilization, while the middle and higher tiers were built as mechanically stabilized earth. The stability of the proposed stabilization was analyzed using 2-D non-linear finite elements. After construction, monitoring of the wall continued for about 8 months to check its performance, and indicated lateral and vertical wall movements were less than 25 mm and 6 mm, respectively, indicating effective slope stabilization.INTRODUCTIONStabilizing earth slopes using piles to connect near-surface unstable soils to underlying stable ground masses has been investigated by many researchers, who presented various approaches to evaluate the contribution of the pile system towards improving the stability of the slope. Some of these approaches consider the piles as structural elements receiving forces from the upper sliding ground mass and transmitting these forces to the underlying stable one. The force from the top sliding mass is applied at between one third and one half of the pile embedment into the top sliding mass, Anagnostopoulos et al. (1990), Fukuoka (1977) and Matsui et al. (1988). The point of application of the sliding force was explored based on successful case histories while addressing the safety factors for both geotechnical and structural design, Vessely A. et al. (2007). The development of numerical analysis techniques utilizing the method of finite elements (FE) also enabled better analysis and design of slopes stabilized using piles. A FE-based approach was successfully utilized to design slope stabilization with target safety factor based on the shear and bending demands and the spacing of the piles, Pradel D. et al. (2010).After Hurricane Sandy in October 2012, the stability of many properties constructed atop earth slopes located along the coast of the Atlantic Ocean has become a concern due to storm-induced erosion. This paper presents the analysis, design and construction of a hybrid slope stabilization system utilized at one of these storm-impacted properties, which is located in the Atlantic Highlands, New Jersey in the United States. The subject property consisted of a two-story residential dwelling and a parking structure, and was built on top of an about 8-m-high earth slope having crest at about elevation 10 m (el 10) and toe at about el 2."

Jan 1, 1900