Search Documents

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003

By Gunhild Hennum, Tewodros Tefera, Gisle Håland, Annette Jahr

"Abstract The Gudrun field is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected to support the topside and was installed in 2011. The jacket shall be able to support 16 of 0.762 m (30 in) diameter conductors and is equipped with a drilling deck to allow for pre-drilling by a jack-up rig through the jacket. In general the soil conditions below mudline comprise of a thin top layer of very loose to dense sand overlaying several layers of sandy clay, ranging in stiffness from firm to hard. Below some 30 m depth the soil consists of layers of medium dense to dense silty sand overlaying very hard sandy clay containing thick beds of sand to 100 m depth or more below mudline. The jacket is secured to the seabed by twelve 2.438 m (96 in) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. Different design methods were used to determine the pile penetration depth. Pile drivability was evaluated using best estimate and upper bound soil parameters. The pile driving and blow count record show that the target penetration was reached as predicted. This paper discusses the different methods used to determine the pile capacity, target penetration depth and the drivability analyses made for the Gudrun jacket piles. The soil resistance during pile driving is back-calculated from the pile installation data and compared with the prediction made.IntroductionThe Gudrun platform is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected for the Gudrun platform. The general Gudrun platform jacket configuration is to a large extent dictated by the topside layout, the requirements for support points enclosing the well slots and access for the jack-up rig. The Gudrun platform jacket is a traditional 4 legged structure with a vertical side towards the jack-up rig. At the seabed the jacket is quadratic with a base dimension of 40 by 40 metres. Figure 1 shows the Gudrun jacket during load-out from the fabrication yard to the transport barge. At the site the jacket was lifted off the barge, upended and placed on the seabed by the installation vessel. The jacket is secured to the seabed by twelve 96"" (2.438 m) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. The target penetration of the piles is 47 m."

Jan 1, 2014

By David L. Borusiewicz, M. Suri Surendra

"Abstract Helical piles have been used as anchors and for supporting lightly loaded structures as a method of underpinning, etc in the past. Recently, helical piles are being used to support new structures because of their simple installation process using relatively light and mobile equipment. This paper presents the results of evaluation and design performed for the temporary support of existing piers during a bridge rehabilitation project.INTRODUCTIONThe helical screw foundation was invented and patented by Alexander Mitchell in England in 1833. He installed screw piles to support lighthouses in the tidal basins of England. Many applications in the earlier years in the USA were in North Carolina and in Florida to support lighthouses (in coastal plain deposits). A lighthouse of similar foundation design is still in use at Key Biscayne, Florida.In the USA, the helical piles were reintroduced as foundation elements for electrical transmission towers. Helical piles were also used for anchoring guys of self supported towers and as tie-backs for excavation support systems. Typically, helical piles are being used for supporting lightly loaded buildings and for underpinning buildings undergoing distress as a means of remediation. The helical piles are not commonly used in the transportation industry.HELICAL PILESHelical pile is a segmented deep foundation system with helical bearing plates welded to a central steel shaft. Load is transferred from the shaft to the soil through these bearing plates. Central steel shafts are available in either a square shaft (Type SS) or a round shaft (Type RS). The Type SS series are available in 38 mm to 57 mm square sizes. The Type RS series are available in 73 mm to 114 mm diameter sizes. Type SS-RS combinations are also available for compression applications in soil conditions where dense/hard soils must be penetrated with softer/loose soils above the bearing strata.The leading segment consists of a shaft with one or more helical plates that are welded to the shaft. The plates vary in diameter from 203 mm to 355.5 mm and have a thickness of 9.5 mm or 13.7 mm. Typically the plate diameter increases from the bottom of the shaft upward. A helical bearing plate or helix is one pitch of a screw thread. All helices, regardless of their diameter, have a standard 76 mm pitch. Being a true helical shape, the helices do not auger into the soil but rather screw into it with minimal soil disturbance. Helical plates are generally spaced a distance of two to three times the diameter of the plate directly below in order for them to function independently as individual bearing elements. A typical detail of helical pile is shown on Figure 1."

Jan 1, 2014

By Willie M. NeSmith

The use of drilled (screwed) displacement piles is an emerging sector of the United States deep foundation industry. During installation of these systems, a Ko to Kp environment is created in the materials surrounding the pile immediately prior to casting, and this condition results in increased shaft and toe resistance in soils where displacement leads to densification. Current continuous flight auger and drilled shaft design methodologies in the United States assume a Ko to Ka condition in the vicinity of the pile, and are thus an inappropriate starting point for static capacity analysis of drilled displacement piles. This paper examines constructability issues, and the sensitivity of performance to installation, and offers an empirical design methodology for drilled displacement piles. The proposed design process has been based on evaluation of 40 load tests, primarily in granular materials, and in a variety of geologic settings, and includes modification for soil types within the coarse-grained range.

Jan 1, 2002

By Naresh Koirala

The Greater Vancouver Regional District completed installation of a 2.5 Km long, 2400 mm diameter concrete sewer in Delta, British Columbia in 2000. The sewer traverses through area of peat and soft ground. The ground investigation along the sewer alignment consisted of cone penetration tests and auger drilling with standard penetration tests. The gravity sewer is supported on precast, pretensioned spun concrete piles imported from Malaysia which had never been used for a major project in North America. The capacities of the installed piles were tested using pile driving analyzer (PDA) and three static load tests. A total of 46 PDA tests were carried out during pile installation. The paper describes the pile vetting process the owner went through prior to accepting the piles for use in the project and performance of the piles. It compares the pile capacity estimated from the PDA tests with that estimated from soil mechanics methods using data from cone penetration tests and standard penetration tests. The ranges of estimated capacities calculated by different methods are discussed from design capacity selection considerations.

Jan 1, 2004

By Roy C. Bartholomae, Jeffrey Shawn Peterson

1. INTRODUCTION In the early 1980s, the U.S. Department of the Interior’s Bureau of Mines Pittsburgh Research Center required that a large reverberation acoustic facility be constructed. This facility was designed to determine the sound power level emissions of mining equipment, especially continuous miners and jumbo drills. A contract for a conceptual design of a reverberation chamber was awarded to Wyle Laboratories of Huntsville, AL, which had extensive experience in the design, construction, and accreditation of acoustical reverberation chambers. The following standards were referenced as guidelines for the design of the chamber: ANSI S1.31-1980, “Precision Methods for the Determination of Sound Power Levels of Broadband Noise Sources in Reverberation Rooms” and ANSI S1.32-1980: “Precision Methods for the Determination of Sound Power Levels of Discrete-Frequency and Narrowband Noise Sources in Reverberation Rooms.” Specific requested criteria included that the room be large enough to accommodate typically large mining equipment and that there be adequate acoustical modal density in the frequency range of interest. It was also required that the room dimensions would support broadband acoustical measurements down to the 100 Hz third octave band. With the closing of the Bureau of Mines in 1996, this reverberation chamber lay dormant for a number of years. However, this facility is now part of the National Institute for Occupational Safety and Health’s (NIOSH’s) Pittsburgh Research Laboratory (PRL). One of NIOSH’s missions is to decrease noise induced hearing loss among the nation’s mineworkers. To this end, PRL researchers are refurbishing and instrumenting this reverberation chamber to facilitate assessment of the various engineering controls being developed to decrease the sound power level emissions of mining equipment. Early on, this work has sought to bring the chamber up to the level of ISO 3743-21 standard for engineering grade measurements for broad-band noise, with a longer range goal of improving the lab to meet the requirements of ISO 37412standard for broadband precision grade measurements. 2. DESIGN OF THE REVERBERATION CHAMBER The nominal room dimensions are 18.3 meters long by 10.3 meters wide with a height of 6.7 meters. The chamber volume is 1,286 cubic meters. These dimensions are important, as few reverberation facilities are large enough to test typically huge mining equipment. The floor is poured concrete with a sealer to make it acoustically reflective. The walls are built of hollow concrete block, 16 inches long x 8 inches high by 12inches thick. Each block has two hollow cores. The hollow block cores were completely filled with concrete with horizontal and vertical steel reinforcing bars 16 inches on center. This was done to supply a

By Shaw-Shong Liew

This paper presents the design concept using floating piles to support 2500Ton oil storage tanks on a very soft alluvial clayey soil of about 40m thick in Riau Province of Sumatra, Indonesia. The floating piles of various penetration lengths were designed to support seven numbers of such storage tanks seating on a 20m diameter and 500mm thick reinforced concrete (RC) circular raft. The pile points have been strategically located at the RC raft. Varying pile penetration lengths have been designed to minimize the angular distortion of the thin RC raft and the out-of-plane deflection at the tank edge. Vibrating wire strain gauges were installed at different levels inside the ø350mm prestressed reinforced concrete piles to measure the load transfer profile during the static load tests and water-loading test. The installation and interpretation of the instrumentation are described and discussed. Boreholes, in-situ tests like piezocones, vane shear tests and standard penetration tests, and laboratory testing were carried out to obtain geotechnical parameters for the pile designs. Static load tests were also carried out on the spun piles of varying lengths of 24m, 30m and 36m respectively. It has been demonstrated that the floating pile system can be a cost effective design to support heavy structures on very soft compressible deposits with satisfactory performance. Finally, the design concept validated with the results of instrumentation is discussed.

Jan 1, 2002

By Bidjan Ghahreman

A total of 120 micropiles were constructed for foundations of a new selective catalytic reduction (SCR) unit in a coal-fired power plant east of Kansas City, Missouri. Construction was performed under restricted overhead conditions because of the existing facilities. The subsurface profile included about 70 feet of overburden composed of granular fill, stiff to very stiff cohesive material, medium dense sand, and very dense gravel. The bedrock was composed of alternating layers of shale and claystone (weak rock) and limestone (strong rock). It was decided that the bond zone would be entirely in the bedrock. The design rock profile along the bond zone was composed of 10 feet of shale and claystone underlain by 10 feet of limestone, which in turn was underlain by shale and claystone. To achieve the design compression and uplift capacities of 100 tons and 60 tons, respectively, a length of 23 feet was determined for the bond zone. Compression and uplift load tests were performed to verify the design. IBC-2000 elastic line, Decourt (1999) extrapolation, and Chin-Kondner extrapolation were used to interpret the load test results. The interpretation of load test data indicated that both compression and uplift capacities far exceeded the respective design loads. Spring constants of 397 tons per inch (T/in.) (in compression) and 290 T/in. (in uplift) were estimated from load tests at respective design loads. During the compression load test, no sign of creep was observed after the applied load was maintained at the design load (100 tons) for two hours.

Jan 1, 2009

By A. J. Paul Laprairie

The process for which it is to be used is too often the only consideration in the design of a vessel. A de-sign allowing for practical manufacture and erection, as well as for proper maintenance, can often give over-all economies. Most platework in-stalled today is of welded construction. Therefore, metallurgical control is important in its manufacture. Also, because many concentrating and re-fining processes tend to be corrosive, the subject of protective coatings as a part of the manufacturing process is extremely important. The plant de-signer should know how to evaluate and specify controls for the metallurgy and for the coatings. Mining operations are becoming more sophisticated in the field of mechanical engineering. More and more emphasis is being given to preventive maintenance. The first step in any maintenance program, however, is good inspection service. This paper will suggest methods for the inspection of platework, and outline methods for repair and replacement.

Jan 1, 1963

By M. Salimov, J. Sattarvand

The conventional visualisation method of remote equipment is through the installation of one or more cameras on the machine, and sending a live feed to the operator’s flat display. However, the performance of the teleoperation can be enhanced using better visualisation through virtual reality (VR). This paper presents the process of the design and manufacturing of a robotic platform that will be used in the next phase of the project for a VR-assisted teleoperated excavator. The robot consists of a loading boom and arm arrangement installed on the undercarriage of a CAT300-9D. All hydraulic cylinders are replaced with electric actuators, and crawling motors are substituted by electric motors. The pieces of the boom and the arm, as well as the bucket were designed in Autodesk Inventor, and manufactured from aluminium sheets using a desktop and CNC machine. Parts are joined by pins and welding as needed. An Arduino-based control system is developed for the robot, and motor controllers are used to convert the power commands from the microcontroller to the high-amperage actuators. The control system is capable of communicating with a wireless Play Station controller to operate remotely. The manufactured robotic excavator is planned to be utilised in multiple autonomy research projects.

Sep 1, 2021

By P. Cheung, J. Gulyas, R. Clary

Over the past 50 years, the use of autoclaves in the metallurgical industry has evolved from final metal recovery (hydrogen reduction) and purification (sulphide precipitate oxidation) to treating whole ores and concentrates. Recent process developments, such as the use of autoclaves for laterite leaching, have necessitated higher temperature and pressure operations, which in turn have seen marked advancements in technology and manufacturing capabilities to keep in step with process demands. This paper will discuss the advances in technology in terms of design, materials and construction of autoclaves and liners, typical dip tube design and geometric layout. This paper will also address specific auxiliary equipment, such as acid and steam injection systems, and components, such as agitator seal systems.

Jan 1, 2004

By Nathaniel Arbiter

The development of flotation machines since the first industrial use of the process can be divided into three stages. The first, up to about 1930, was marked by diversity in the means for contacting floatable mineral with the air/ water interface and for generating the interface, as well as in cell design. By 1927 Taggart (1) could list 170 patents covering flotation cells, and he mentioned dozens which were or had been in operation. He divided cells into eight categories according to design, type of separating interface, and where in the cell and how separation took place. These were: (1) Film or skin flotation with wet or dry oiling of surfaces; (2) pulp body process with bubbles generated chemically by pressure reduction, by vacuum or by boiling; (3) agitation-froth processes involving local supersaturation with air; (4) bubble column; (5) pneumatic; (6) cascade; (7) subaeration; and (8) combination and miscellaneous types and processes. Most widely used then were the agitation-froth, sub- aeration, pneumatic types. By 1943 a significant reduction in categories had occurred to the two main divisions of mechanical and pneumatic cells according to whether agitation and aeration were (a) by an impeller with or without compressed air, or (b) by compressed air alone. Cells at that time were still relatively small; the Morenci Concentrator completed in 1942 used 432 1.7m3 (60 cu ft) Fagergrens for roughing 45,000 and later up to 55,000 t/d.

Jan 1, 1979

By C. Geenen

At its Olen site, Union Minière Copper operates a new full-size deposit tank house. A first 200,000 t/y module was commissioned in October 1996, and an additional 130,000 t/y unit started in April 1998. The main objectives of the new tank house project were to produce grade A cathodes starting from anodes with a wide range of compositions and at a minimal operating cost. The tank house uses Isa Process technology. Based on the process parameters agreed upon with MIM, UM Copper developed the basic design and UM Engineering was the in-house contractor for the engineering. The new tank house is equipped with advanced technology polymer concrete cells, automated two-bale cranes and high-capacity machines. The first 200,000 t/y module treats anodes with a more conventional composition at 330 A/m2; the second 130,000 t/y module treats anodes with a high slimes fall (12- 13 kg/t) at current densities up to 285 A/m2. After some teething problems, the new tank house is meeting all set targets. This paper illustrates and comments on the design characteristics and operational results.

Jan 1, 1999

By Guoming Liu, Weibai Hu

The designing aspects of column profile, cross-section and height, types of aerator or air sparger, and feeding and discharging devices have been designed and tested. In operating aspects, the flotation column: has beer, compared with the conventional mechanical flotation machine in large- scale plant practice. It has been found that the reagent conditioning time and the slurry residence time required in the column are longer than those in the mechanical flotation machine. The general opinion is that the flotation column can show some effectiveness in specific cases as long as it is properly designed and carefully controlled.

Jan 1, 1988

By Y. Poornachandra Rao, P. C. Sudhakar, L. Malakondaiah

NBV commissioned a 27.6 MVA furnace in the year 2005. This paper explains: a)Furnace design features b)Furnace process control, Direct slag granulation c)Continuous casting, Waste heat recovery, Sintering d) Gas cleaning plant, Protection of Environment. Keywords: Furnace Equipment, SiMn Production, Casting, Heat Recovery and Low hood

Jan 1, 2007

By Ken J. Fair, Vicken H. Aprahamian, Gus Van Weert

A consortium of Canadian mining companies, engineering firms and the Ontario Government has supported Hydrochem's efforts in the last year to design and cost a 10 tpd NITROX PROCESS® demonstration plant. A 5 kg per hour mini plant was installed at the Hydrochem facilities in Brampton, Ontario. This paper describes design testwork on Dickenson Mines arsenopyrite concentrate and application of the findings to the demonstration plant flowsheet. The control of nitrates in discard solids and stack gases is discussed in detail. Nitric acid oxidation of arsenopyrite results in significant ele- mental sulphur formation, enough for it to be detrimental to sub- sequent cyanidation. Flowsheet variations aimed at dealing with this process characteristic are discussed and testwork results on one option (hot liming) are described.

Jan 1, 1988

For many years the scrubbing of roaster gas carrying sulphur dioxide has been carried out at the plant of the Electrolytic Zinc Co. of Australasia Ltd. at Risdon, Tasmania, using long horizontal tubes. in which the gas stream crossed a shower of water. In order to provide for increased roaster capacity, it was evident that additional gas scrubbing capacity would be required to prevent pollution of the atmosphere.This provided an opportunity to review the whole operation of gas scrubbing and an investigation was initiated to determine the characteristics of a counter-current type of scrubber. It was hoped that a change to this type of scrubbing would also reduce the sulphur dioxide concentration of the gas delivered to the atmosphere to a negligible amount. This, paper outlines results obtained from an experimental tower which was operated under a wide range of conditions, the packing height, gas flow, water flow, water temperature, and concentration of S02 in inlet gas being varied independently. A description is given of the leading features and operating characteristics of the plant units, which are designed on the basis of the experimental results. Operation of the new scrubbing system commenced on October 5th, 1948.THE PROBLEMThe gas which is handled carries S02 which may vary in concentration from 2% to 5%, and reaches the scrubbing system at a temperature of approximately 180 deg. C. An appreciable amount of suspended material accompanies the gas which has passed the cyclone system.

Jan 1, 1949

By D. E. Pickett, J. A. Roland Faucher

"INTRODUCTIONMineral processing is undergoing growth and change at a rapid rate. The modern flotation process was discovered only in the mid-twenties, and uranium leaching in the mid-fifties. The growth of individual unit equipment size is also a recent development and is perhaps most dramatically illustrated by the increase in size and connected horsepower in grinding mills. It is also apparent in much of the equipment used in mining operations.These technical and mechanical developments have influenced the design of plants but not to the expected degree.Many metallurgists believed until recently that grinding an ore in the absence of steel results in a loEs of selectivity in the flotation. However results reported by Thornton (1), Fahlstrom (2), Canmet (3 & 4) have shown on the contrary better selectivity and improved recovery at a lower operating cost. According to the Aitik (2) plant results, the net difference in cost plus tailing value in favour of the two-stage autogeneous grinding circuit is in the order of 40 cents per ton of ore milled. Even a greater difference was indicated by the results obtained by Canmet on a sample supplied by Mattagami Lake Mines Ltd.Yet how many plants are taking advantage of these findings and how many plants are being converted. How much more improvement of the results would have been obtained if these tests had incorporated optimization of classification efficiency? By nature the mining industry and the mineral processors are conservative, and tend to emphasize the possible penalties for an unsuccessful innovation out of proportion to the potential rewards even for a significant improvement."

Jan 1, 1979

By A. Paulin, A. W. D. Hills

The work has shown that packed-bed behaviour can be predicted from the results of single-particle experiments, total reaction times being predicted somewhat more accurately than gas and solid temperatures and gas compositions. A small laboratory packed-bed reactor was built and used to study the decomposition of beds of specially prepared CaCO3 spheres, steps being taken to minimise the effects exerted by the walls of the bed on processes occurring within the bed. Gas and solid temperatures and gas compositions were measured at various points in the bed and compared with theoretical predictions based on kinetic data determined in previous single-particle experiments. The measured solid temperatures and total reaction times agreed remarkably well with the values predicted theoretically. Gas and solid temperatures measured after the reaction had finished at any point in the bed did not agree with the theory. This was because solid temperatures in the bed rose very rapidly once the reaction was completed and the walls of the bed could not be heated at a sufficient rate for their temperatures to rise as rapidly; thus some loss of heat from the bed to the walls was inevitable, and this could not be accounted for in the theory. In addition, the theory did not allow for the conduction of heat within the bed, and this resulted in some further slight discrepancy between the measured and predicted values, particularly after the reaction was completed. Gas compositions measured in the bed were rather scattered, but, even so, they agreed moderately well with the predictions of the theory.

Dec 1, 1971

By Mark Craddock, Johan Swanepoel

In this paper we present The Ultimate Flotation Cell, a newly developed flotation cell that is proving very popular in the industry. All flotation cells have only one purpose and that is the recovery of the required product, the patented impeller and disperser system of the Ultimate Flotation Cell allows total flexibility in order to achieve the optimal recovery. This ability to tune the cell performance provides the optimization of the ?capture? (collection) stage, all existing models address the need for a wide bubble size distribution (100µm-2 mm) to obtain a better flotation size-by-size, Yoon, 1999,Yoon 2000, Franzidis and Manlapig, 1999. The Ultimate Flotation Cell provides flexible performance optimization. This ability to optimize the flotation regime particular to a specific ore is achieved by the following factors: ? The impeller allows vastly improved air induction rates compared to conventional and sparged cells. This ability to induce and disperse large quantities of air, in a controlled manner, allows the cells to be tuned to give the optimal Sb by varying the rotational speed via a VSD which every cell is fitted with. ? The patented impeller gives a very constant and stable air induction rate, which ensures that the cell?s circulation pattern is constant, giving a very stable surface, allowing optimal froth depth. ? Although conventional dart valve, level control can be offered, great success has been achieved with a simple draft tube/sand relief device. ? The cells have a inlet design similar to the old Denver ?Cell-to-Cell? design, which guarantees the at lease one pass through the mixing zone in each cell. Actual plant performance data will be presented from two plants, one in Zambia and the other in the DRC.

Jan 1, 2007