Search Documents

By R. F. Harig

Designing an underground nuclear waste repository is a complex process. Although many decisions are involved before the design is complete, the first three--what the target horizon is, what the underground boundary is, and where the entry point will be located--are important because they establish the basis for the entire repository design. Even more important than these decisions, however, is the data on which the decisions are based. Because the current data are limited, an aggressive data gathering program is needed during the next design phase to augment information about the intricate interplay among all facets of the repository design and the geologic medium in which the proposed repository is to be developed. Although unique to modern engineering enterprises, the challenges involved in designing a repository in the unsaturated zone are within current technology and engineering practices.

Jan 1, 1991

By L. Cheng

Almost all modern cutting bits use a cemented tungsten carbide tip to provide adequate hit life against wear. Laboratory tests by the US Bureau of Mines have indicated that the number of strikes for ignition increased by a factor of three with a new non-rotating bit impacting a sandstone block when the clearance angle was increased by 10°, and that carbide-tipped bits allowed more strikes before ignition than steel-tipped bits by a factor of 7 to 10. Recent field tests in an operating coal mine indicate a dramatic reduction in the frequency of frictional ignitions and improvement in hit life by using a mushroom-shaped hit cap and a larger initial clearance angle. The latter was achieved by increasing the hit attack angle. Improved hit performance through selection of the grade of tungsten-carbide is a com¬promise between fracture resistance and wear resistance. A large clearance angle should he maintained by various techniques, such as a variable attack angle holder, or a reusable hit that can he reground.

Jan 1, 1990

By Michael McVay

The use of augered cast-in-place piles has seen tremendous growth under commerical structures in the past twenty years. Problems with vibration, soil densification and/or heave associated with driven piles do not occur with properly installed augered piles. Augered cast-in-place piles were originally constructed (1950s) with diameters of .31 m (12 in.) and lengths up to 6.1 m (20 ft); however with the advent of better drilling equipment, diameters varying from .41m(16 in.)to .61 m (24 in.) and typical depths ranging from 18.3 m (60 ft) to 24.4 m (80 ft) are achievable. Reinforcement may vary from a single high strength rebar (Grade 60) at the top of the pile to a continuous steel cage depending on loading (compression, tension-uplift, and lateral). Typical axial design loads (compression) for a single augered cast-in-place pile are in the 445 kN (50 tons) to 890 kN (100 tons) range.

Jan 1, 1997

By Bauduin C. Besix

The Eurocode 7 "Geotechnical Design" is based on "Limit State Design", tackling the uncertainties as much as possible at their source through: - selection of characteristic values of variables (loads, soil properties, pile resistance,...); - partial factors applied on the characteristic values; - model factors to account explicitly for uncertainties of the calculation rule if necessary. Eurocode 7 will propose three "design approaches". The selection of one of them will be by National Determination. For pile design, the approaches are: - approach 1 is a "material factoring approach" at load side and a "resistance factoring approach" at resistance side. The structural and geotechnical design are checked for both of two separate sets of partial factors. - approach 2 is a "load and resistance factoring approach" and is in several aspects close to a deterministic approach. The design is checked for one set of partial factors. - approach 3 is a material factoring approach, at load as well as at resistance side. The design is checked for one set of factors. The aim of this paper is to introduce to the design of pile foundations based on pile load tests and on ground test results (semi-empirical and analytical methods) in the frame-work of the three design approaches. Detailed attention is devoted to: - the selection of the characteristic value of the pile resistance, accounting for spatial variability and stiffness of the structure; - the reliability of the prediction of the pile resistance using analytical or semi-empirical methods which may be accounted for through a "model factor". The results of a large test campaign on screw piles in OC Clay and a calculation example illustrate the proposed procedure when calculation rules using CPT results are used.

Jan 1, 2002

By J. Palarski

In the Polish coal mining industry, the use of mine waste in underground backfill has been the most common means of providing ground support to minimize surface subsidence, increasing extraction ratios, and reducing the quantity of waste for surface disposal. Over the last decade attention has been focused on the use of different waste as filling material of underground workings and grouting of roof fall rocks in caving area. In the paper, a brief history of the development of fill technology in Polish coal mining industry is presented. Next, the paper discusses various criteria that should be taken under consideration in the preparation process of a fill slurry and grout, fill distribution systems, mining geometry and placement methods. Moreover, in the paper evaluation of the potential of utilizing coarse and fine waste as a resource material in the production of a backfill slurry and grout for filling and injection in abandoned mines is presented.

May 1, 2007

By Andrew Baxter

This paper focuses on the design of steel bearing plates to transfer load from tiebacks and tiedowns to a concrete mass. It lists and describes the various available procedures for design of bearing plates as well as explains the design procedure recommended by the authors, which incorporates the Post Tensioning Institute (PTI) recommendations. The paper includes a step-by-step design example following the recommended procedure that captures the most important aspects of plate design. The dimensions of the plate calculated from this example are compared to the design dimensions obtained from various other procedures, including those by American Association of State Highway and Transportation Officials (AASHTO) and VSL International, Ltd. (VSL). The paper also includes the results of numerical modeling of the plate that will help the reader understand important aspects of plate-concrete interaction. The authors envision that this paper will serve to create an understanding in the geo-industry of suitable design methods and help improve procurement of bearing plates for tiebacks and tiedowns.

By Satish Kate

Mining of Iron Ore in India is done by Surface Mining methods and most of the deposits are massive and are occurring in Hills, surrounded by green forest cover. While majority of iron ore produced are from mechanized mining systems, some quantities are also produced from semimechanised mines. In mechanized mines, apart from state-of-the-art level of mechanization, the Run-off-Mine ore is subjected to multi-stage crushing, screening and washing/beneficiation, for improving the grade and ensure segregating of different size range. The steel plants within the country have been operating their own captive mines, where both lumps and fines are used in their furnaces. In case of mines, which exclusively supply ores to export market, the lumps produced yield very high price and thus efforts are being made to maximize lumps recovery. The mine, where the author had been associated, is an export-oriented mine which supplies iron-ore to Japanese steel plants.

Jan 1, 2004

By David J. Puller

As part of the value engineering process on a major Design Build highway project, instrumented trial pile load tests were used to achieve savings in cost and time on the foundations for a major river crossing. Two trial piles were tested close to failure load at 25MN. Following the interpretation of the pile load test results which included the determination of the ultimate shaft and base capacity, the mobilisation of the shaft and base resistance with pile displacement, and correlations with vertical effective stress and SPT profile, a revised design methodology was proposed. A 25% enhancement on commonly assumed ultimate shaft friction in Chalk was adopted. In addition a significant reduction in the Factor of Safety on end-bearing capacity generally used was also implemented. The revised design resulted in a significant cost and time saving on the piling operation with the pile length reduced by up to 6m (approx. 20%) for the river piers.

Jan 1, 2002

By Eddie Woods, Jon Hurt, Roger May, Paul Watson

The Channel Tunnel Rail Link (CTRL) will be Britain’s first major new railway for over a century—a high-speed line running for 109km (68 miles) between St. Pancras station in London and the Channel Tunnel. The new line has been under construction since October 1998 and the first phase will open in October 2003. The project includes22km of twin 7.15m ID TBM bored tunnels under London and the River Thames, and the 3km North Downs Tunnel, the first major NATM tunnel to be constructed in the United Kingdom since the collapse of the Heathrow Express Tunnels in 1994. This paper will discuss the design of these tunnels and describe the construction progress to date. The discussion will include details of segmental lining design, TBM specification, and sprayed concrete lining design.

Jan 1, 2003

By D. R. Miller

The use of fully grouted cables for ground reinforcement in underground mining is becoming widespread. Reinforcement design for this application has tended to be empirical although some two- dimensional design techniques have been developed. This paper describes a technique based on a model of the behaviour of cables placed across planes moving in shear. The model is three- dimensional and includes a simple model of the 'dowel' effect which arises from the bending of the cables. The model determines the shear resistance developed at a particular shear displacement assuming joint friction and cable parameters. Using data for twin 15.2mm dim. steel strand cables, and a concept of reinforcement efficiency, the application of the model to design wall support in open stopes is demonstrated. The examples consider the cases where major planar structures are known in location and orientation and where, as is more common is open stope development, mapping has indicated that a distribution of potential shear failure structures may be present. The actual location and orientation of potential shear planes is not known. These two cases highlight the underdesign of reinforcement that may arise if the distribution of orientation of potential shear planes is not considered.

Jan 1, 1984

By Robert H. Merrill

INTRODUCTION In most cases, the design of an underground mine is based upon the premise that the ground either will cave or will be stable. This chapter concerns the design of a mine in ground that will cave readily or with some as¬sistance, such as by long-hole drilling and blasting. Some of the more widely used caving systems of mining are panel caving, block caving, sublevel caving, and large pillar recovery. Some of the less widely used systems are glory-hole, top slicing, and induction caving. Al¬though the common practice of pillar robbing is not usually considered to be a caving system, this subject will be treated as a part of this chapter. BASICS OF CAVING Caving systems are most successful in ground that will cave in sizes that will flow through openings and grizzlies, and will easily load in cars or on belts for haul¬age. The ground most likely to cave well is highly frac¬tured and contains breaks, flaws, or other discontinui¬ties that form planes of weakness. Also, caving action can be greatly enhanced if the host rock itself is low in compressive, shear, and tensile strength. Ideally, a cav¬ing system of mining is best employed when the criteria for caving is a feature of the ore body and the develop¬ment drifts, haulageways, and drawpoints can be mined in a highly competent rock beneath the mineralized zone. However, the development is often in the same, or similar, fractured rock and the openings require sub¬stantial artificial support to assure stability. Several clues can be assembled to identify potential caving ground; however, for borderline cases, no sure method has been devised to date. The diamond-drill cores taken for exploration can provide an excellent clue provided drilling is performed carefully by experienced drillers. For example, if the ground is cored in such a manner that the breaks in the core are caused more by failure of the rock than by whipping core barrels, plugged drill bits, or other drilling causes, and the intact core lengths are consistently long [say, 0.6 to 3 m (2 to 10 ft) of unbroken core], there is little reason to believe the ground will cave without considerable as¬sistance. This is especially true for rocks with compres¬sive strengths above 34.5 MPa (5000 psi) and tensile strengths above 2.1 MPa (300 psi). On the other hand, if core recovery is low (below 80%) and the recovered ore is broken in small pieces and the breaks are along obvious weaknesses in the rock, the chances are excel¬lent that the ground will cave. This is true even when the rock between the defects has high compressive and tensile strength. Another clue has already been mentioned, that is, the measurement of the physical properties of the rock and the natural planes of weakness or defects in the rock. The planes of weakness in the rock can often be detected from outcrops, cores, or other exposures of the rock under consideration. Some rock types are known to be strong and will sustain large, unsupported open¬ings and would be difficult to cave intentionally. Yet the same rock type can also contain unbonded or weak planes of weakness or fractures, and in these locations the rock would undoubtedly cave with little assistance. Therefore, although the inherent strength of the rock is a factor in caving, the natural defects in the rock are more often the deciding factor. DESIGN CONCEPTS For the most part, the design of openings for caving ground is a problem of the interaction of openings over a relatively large area of the mine. To illustrate, Fig. 1 is a simplified section of a series of openings along the grizzly level or draw level of a block caving or panel caving development, and above this opening is a simpli¬fied section of a room-and-pillar arrangement on the undercut level. At this stage of the development, the stresses around the openings on the grizzly level are only moderately influenced by the openings on the undercut level and vice versa. Therefore, the stresses around the openings are approximated by the stresses around single or multiple openings in rock, the values of which are de¬scribed in the literature (Obert, Duvall, and Merrill, 1960; Obert and Duvall, 1967). Once the pillars on the undercut level are blasted (Fig. 2), the situation changes abruptly. The undercut opening (prior to caving) now can be approximated as an ovaloidal opening above the grizzly drifts and this opening tends to shield the vertical stress field. As the caved stage is drawn the stope approximates a much larger rectangular or square opening filled with rock, and if the rock is not sustaining a major portion of the stress field, this opening can be considered (for en¬gineering purposes) to be empty and the stresses that interact between the larger and the smaller openings take on a totally new perspective (see Fig. 3). Next, let the material cave to the surface, and let the caving ma¬terial sustain some stress, but much less than if the ma¬terial were intact. This condition is similar to a soft inclusion in a rigid body and has been treated in the literature (for example, Donnell, 1941). At this point in time, the grizzly drifts are subjected to the stress con-

Jan 1, 1982

By Mark E. Smith, Gerald J. Gierszewski

Introduction The purpose of this paper is to present a procedure used by the authors for evaluating and designing soil liner systems. This method is particularly valuable in evaluating various treatment schemes for chemically amended soil liners. A tabulation of laboratory test results on various soil types are presented to quantify the effectiveness of certain treatments. A typical liner design program includes developing and proving soil borrow sources, designing the cross-section of the liner system, developing construction specifications, and providing construction services to ensure the intended product is achieved. Material Source Development The first step in designing a soil liner is to identify and evaluate suitable borrow sources within an economical haulage range. This is best done in a two step approach: a reconnaissance level investigation to identify target areas and a detailed evaluation of those targets. Reconnaissance: The goal of the preliminary investigation is to locate potential borrow sources for liner quality soils. This includes all natural materials which can be compacted, chemically treated, or otherwise amended to yield an installed permeability at or below some target value. This requires utilization of all available data sources: Soil Conservation Service, BLM, aerial photos, USGS geologic maps, and project geologist records. The goal at this stage is to locate shallow deposits of favorable soil types. The Unified Soil Classification System provides an excellent first pass grouping. Clays, clayey sands and silts are the most favorable soil types, although silty sands and occasionally clayey gravels can make excellent liners, and are often amenable to chemical modification. The lowest permeabilities are generally achieved with CH, CL and MH soils. Once preliminary targets have been identified using visual examination, laboratory classification tests should be performed to further refine the selection. Testing at this stage should include gradation, plasticity and hydrometer analyses. Additionally, "preg-rob" testing should be done as early as practical. Preg-rob is a phenomenon where gold or silver ions in solution associate with the clay, or other, minerals. When this occurs, a portion of the gold or silver leached from the ore is actually tied-up by the clay and thus a reduces recovery. Testing for this consists of agitating a small sample of the soil in a solution containing dissolved gold or silver, preferably of similar chemical make-up as the solution which will contact the actual liner. The solution and soil are assayed before and after agitation to determine loss to the clay. A reliable estimate of the hydraulic conductivity, commonly referred to as permeability, can be developed from the D10 value by the use of Hezen's formula: K = 100 (D1012 This relationship is limited to soils where the finer particles do not move due to the force of flowing water (i.e.: "hydrodynamic stabilitym)(1). Additionally, the effect of platty particles on permeability is not as predictable as the effect of equidimensional particles. D10 is the sieve opening size at which 10% of the material is finer. Plasticity is also important from several standpoints. Constructability is directly related to plasticity. Very plastic clays and non-plastic silts both tend to be difficult soils, while medium plastic clays and clayey sands are generally very desirable. Post construction performance is also related to plasticity (e.g. swelling, shrinkage cracking, frost heave, etc.). Additionally, low plasticity silts and silty sands generally do not respond well to chemical amendment. Source Development: The result of the reconnaissance evaluation should be an estimate of the relative probability of developing a suitable borrow source within an economical haul distance. Of course, "economical distance" depends on the degree of handling and treatment the borrow material requires, as well as the cost of synthetic alternatives. The purpose of the detailed investigation is to prove out quantity and quality of material sources, and determine design parameters such as degree of compaction, mixing, treatment and thickness of liner. The emphasis of the testing program should be permeability and strength. Strength becomes increasingly important as the slope of the liner and the height of the heap increase. Permeability testing should evaluate the effects of compaction, water content, mixing and chemical treatment where appropriate. The effects compaction and water content during compaction have on

Jan 1, 1987

By W. Wan, R. V. Ramani, J. M. Mutmansky

"Diesel particulate matter (DPM) emitted from diesel engines is currently considered to be a health problem in underground mines. As a result, attempts have been made to control DPM both by reducing emission rates and by managing the DPM that gets into the mine atmosphere. This paper presents a method for modeling the generation, transfer, and distribution of DPM in coal mining sections through the use of a convection-based computer model so that controls for emitted DPM can be evaluated. A variety of ventilation strategies and diesel deployment schemes for room-and-pillar development sections were simulated to compare their effects on average DPM concentrations at several fixed and mobile personnel locations in the section. Input data for the model was gathered from actual diesel development sections and derived from experimental study results provided by other researchers. Analyzed using the model were ventilation schemes using vent tubing and brattice, exhaust location strategies on the vehicles, and the direction of ventilation at the feeder-breaker location. A summary of results from this study is presented.With diesel equipment holding an important place in underground coal mining and growing in use over time, it is important to develop and improve controls of the exhaust emissions, especially diesel particulate matter (DPM), to further reduce potential health hazards. The proper design and maintenance of diesel engines and on¬board control procedures are paramount requirements for controlling DPM successfully. There is also, however, a significant reduction potential in terms of personal exposure that can be realized by managing the DPM that gets into the airstream. Strategic design of the mining, ventilation, and equipment implementation systems remain essential for efficiently reducing the DPM concentrations.Modeling the effect of diesel exhaust contaminants upon the mine atmospheric quality will permit improved health and safety design of the overall mining and ventilation systems. Numerous studies have been performed to model the distribution/transport of gaseous and particulate emissions in the underground mine atmosphere and some very sophisticated convection/diffusion models have been developed (Skobunov, 1974; Thakur, 1974; Stefanko and Ramani, 1975; Wala, 1980; Bandopadhyay and Ramani, 1983). Most of these models were developed for a single airway or based on the assumption that the ventilation network of a mining section can be approximately represented by a single intake and a single return. The complexity of most models of the convection/diffusion type and the mobility aspect of diesel haulage units made a detailed emissions model very difficult to develop.The current model is an attempt to fill the need for a more generic tool applicable to mining sections employing multiple mobile diesel units by simplifying the convection-diffusion model to a convection-only model. The simplification is based on the fact that the diffusion coefficient will affect only the transient environmental contaminant concentrations with little or no affect on the time-weighted-average concentrations over a relatively long period such as a working shift (Lee et al., 1994). In view of the difficulties involved in mathematical modeling, the approach here is developing and using a computer simulation model. A PC-based FORTRAN 77 simulation model for the analysis of mining systems with multiple diesel sources and any ventilation network configuration was developed to study the distribution/transport of DPM in mine airways, evaluate methods of reducing DPM concentrations, and explore modifications to existing mining practice."

Dec 1, 1996

By M. J. Laurila

Utilizing data compiled from a drilling program and bulk samples taken from a coal reserve, flowsheet performance for a coal preparation plant can be calculated using a desktop computer. Sets of equations defining material balances involving coal preparation plant unit operations are employed to depict plant performance. Techniques are discussed for interpolating washability data and extrapolating size distributions and other critical data to expand on oftentimes limited sets of quality data to a useable data base from which projections can be made. Simulation of flowsheets can be done for a number of different conditions and configurations while still remaining in a limited working memory capacity of 32,000 bytes. Presented within this paper are several pertinent examples.

Jan 1, 1982

By Richard Collins

The projected depletion and the increasing costs of petroleum and natural gas along with the public and governmental resistance to nuclear energy have caused coal to emerge as one of today's answers to both our short term and long term energy needs in power generation. In order to satisfy this need, major increases in coal production are mandatory, thus requiring more and higher capacity coal transfer terminals. The logic for selecting coal as the major fuel for power generation is based on many different reports on the existing and potential energy sources, which include petroleum, natural gas, hydropower, solar, geothermal, and nuclear. The following is a brief synopsis of these reports for each type of energy.

Jan 1, 1978

By Samson Adeosun, Sanmbo Balogun, David Esezobor

"In a typical year, approximately 1.7 million tons of residues and wastes are expected from Ajaokuta integrated steel plant, Nigeria. They will be generated mainly from sinter plant, blast furnace (BF), and basic oxygen furnace (BOF) operations and during rolling and finishing. The residues and wastes include slag, dust, sludge and slurries from gas cleaning, waste water, mill scales and other associated scraps. In this paper concepts for the utilization of residues and wastes in Ajaokuta Steel Plant where no reclamation routines have been provided for in the first and second phases of its project implementation is designed. The paper analyses the sources of the iron oxide wastes and evaluates the quantities expected from the main production facilities of the plant which include the two 312 m2 capacity sintering machines, the two 2000 m3 blast furnaces and two 130-T BOF (of the 2nd phase expansion of the Steel Plant). A reclamation routine designed for Ajaokuta residues and wastes is presented.IntroductionIn the steel industry, approximately 550kg of residues per ton of crude steel arise from the production processes and from pollution control facilities [1- 4]. These residues consist of slag, dusts and sludge, mill scale, spent pickle liquor, and other iron bearing materials. The main by – products generated in the steel industry are listed in Table I.Although major progress has been made in the recycling and use of some of these residues, particularly flue dust, blast furnace and steel making slag, yet a significant quantity are land filled or stockpiled. These unsightly stockpiles occupy valuable real estate and may become a source of environmental pollution if not otherwise disposed. In any case, the dumping option has become quite costly. For instance, one ton of iron ore costs between 28 and 34 US dollar, whereas as much as $20 per ton of steel produced is required to meet environmental compliance obligation in the USA [5, 6]."

Jan 1, 2008

By A. C. Backeberg

There is no South African code for the design of reinforced concrete headframes, and all those erected have been designed on a uniform basis which, up to the present, has tended to be conservative. With certain exceptions designs have generally conformed with British Standard Code of Practice C.P. 114. In the design of reinforced concrete headframes the following loads are taken into account:

Jan 11, 1961

By W. Lum

In the U.S., flexible metal pipe culverts are designed by ring compression theory because the pipes are capable of deflecting and deriving side support from surrounding ground. For economy, tunnel liners are often designed as flexible structures that depend on the lateral pressure of the surrounding ground to maintain stability. In this paper, simple formulas are presented to determine the maximum deflection a concrete tunnel liner may assume and the ring compressive strength of the deflected liner. A tunnel can then be constructed to work within these limits. Similar techniques may be used to design concrete pipes.

Jan 1, 2010

By Osama Safaqah

The new Cooper River Bridge will replace two existing bridges along U.S. Highway 17. The cable-stayed bridge will be one of the largest in the U.S and will connect the City of Charleston and the town of Mount Pleasant, South Carolina. The 1,546-foot long main span over Cooper River is supported by two diamond-shaped towers and will allow for 1000-foot wide navigation channel. The Charleston high-level approach is approximately 4351-foot long and will provide 250-foot wide navigation channel over Town Creek, while the Mount Pleasant high-level approach is 2090-foot long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. Among various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against lateral loading. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies coastal sediments of interbedded clays and sands. The main towers will be supported on a group of 11 shafts and protected from ship collision by a rock island. The High Level Approach piers will be supported on a pair of 2 shafts. The shaft tip elevation is up to 230 feet below water line. An elaborate geotechnical investigation has been conducted on the site including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2005

By I. Mc Dougall, H. Joubert, G. de Villiers

The use of sidewall copper cooling systems to prolong furnace campaign life is becoming an accepted technology solution in the base metals industry. Tenova Pyromet has designed and installed a number of sidewall copper cooling systems in base metals furnaces, including the platinum industry. Apart from increasing the furnace campaign life through the formation of a stable freeze lining, a well-designed copper cooling system enables the plant operator to focus more on optimizing the process to achieve throughput and recovery targets, and to accommodate more varied and available concentrate feed blends. The paper discusses the design of sidewall copper cooling systems for copper smelting and converting furnaces to achieve the above objectives. More specifically, the design of copper cooling systems for top submerged lance furnaces are discussed. An overall increase in furnace heat losses has been raised as a concern for intensively cooled sidewalls. The paper explores the overall heat loss expectations for copper cooled furnaces versus traditional refractory lined furnaces. In addition, the potential use of alternative cooling media is discussed. INTRODUCTION Base metal smelting and converting furnace technologies have been evolving continuously over the past century to satisfy the need for higher throughput, improved efficiency, and longer campaign life. To accommodate these demands, in particular higher smelting intensity and throughput, furnace bath containment systems had to improve. The use of pure refractory lining systems has slowly made room for the use of more intensively cooled lining systems (Joubert, Nikolic, Bakker & Mc Dougall, 2016). These cooling systems evolved from external shell cooling, such as shower or film cooling, to copper plate coolers extending into the furnace refractory lining, and high intensity stave or panel coolers (Verscheure, Kyllo, Filzwieser, Blanpain & Wollants, 2006). Consequently, an increasing number of base metal smelting and converting furnaces are equipped with copper cooling systems, including flash furnaces (Bryk, Ryselin, Honkasalo, & Malmstrom, 1958; Yasuda, Motomura & Kawasaki, 2014; Marx, Shapiro & Henning, 2010), top submerged lance primary smelting and fuming furnaces (Bhappu, Larson & Tunis, 1994; Kim, Lee & Lee, 2000; MacRae & Steinborn, 2018), top submerged lance converting furnaces (Viviers & Hines, 2005; Nikolic, Hogg & Voigt, 2018), primary platinum smelting electric furnaces (Nelson, Stober, Ndlovu, De Villiers & Wanblad, 2005; Jones, 2005; Hundermark, De Villiers & Ndlovu, 2006; Mc Dougall, 2013), and electric slag cleaning furnaces (Joubert, Nourse, Masters & Hundermark, 2005).

Jan 1, 2019