Search Documents

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks currently capable of hauling payloads in excess of 290t. Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Since truck haulage costs can account for 10%-50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, vehicle operating and maintenance costs would also increase prohibitively. There is thus a need for improved design technologies encompassing the construction and management techniques of mine haul roads, appropriate for the wheel loads of vehicles now in use. The aim of the paper is to present the different components of a mine haul road design and management system and to demonstrate the value of its application through case studies. The system has been applied at several South-African surface mines and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and also provided better service, whilst the optimal selection and management of wearing-course materials provided better functionality at lower total transportation operating costs.

Jan 1, 1999

By Michael E. Karmis

New and developing communication systems en-able underground miners to, not only connect to the surface from an increased communication coverage area, but also to be discovered in the event of an emergency. Communication and tracking systems are required by the U.S. Mine Safety and Health Ad-ministration (MSHA) regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broad-cast devices results in a reliable communication network that can better withstand disruption in daily operation and during a time of emergencies. Research on wireless communication in mines has been ongoing since 1922, when the U.S. Bureau of Mines performed experiments in its experimental mine in Bruceton, PA (Schiffbauer & Brune, 2006a). Ac cording to Dobroski and Stolarczyk (1982), ?as early as 1922, Bureau of Mines experiments showed that radio propagation in mines was possible but not practical.? In 2006, the underground communication technologies available to the mining industry had inherent problems that limited communication capabilities. Because harsh underground mine environments significantly reduce line of sight and propagation range and introduce power and safety concerns, the overall effectiveness of underground communication technologies were limited. After several coal mining accidents in early 2006, the U.S. Congress responded with the Mine Improvement and New Emergency Response (MINER) Act, enacted

Jun 1, 2010

By K. R. Griffin

New and developing communication systems enable underground miners to not only connect to the surface from an increased communication coverage area but also to be discovered in the event of an emergency. Communication and tracking systems are required by MSHA regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broadcast devices results in a reliable communication network that can better withstand disruption in both daily operation and emergencies. This paper will discuss recent regulatory developments in underground coal communication systems, the implementation of these new technologies, and how communication system?s networks can be modeled and analyzed using computer simulations.

Jan 1, 2010

For effective backfilling, a system with the 13 features covered under the section: effective backfill systems, is required. Effective backfilling cannot be done with systems that are badly designed, outdated or overextended. But in cases where the requirements for effective backfilling are overlooked, the shortcomings of such systems may wrongly come to be regarded as limitations to the capabilities of backfilling per se. Mining is currently done to depths of 3500 m, and is to go deeper since the gold-bearing reef extends down to 4000 m and 5000 m below surface. Effective backfilling systems will be required at such depths, and with suitable design this can be achieved. Mining the narrow tabular orebody of a typical South African gold mine is described at the start of this paper, then cycloned backfilling is discussed in general, and its effectiveness (most of the fill placed in South Africa is cycloned backfill or ædeslimed tailingsÆ).

Jan 1, 1998

Process engineering principles are used to analyse the features of leaching processes for large masses of low grade, unprocessed ore. Different performance characteristics are related to the numerous variants of these processes. The variant for which reagent enters a heap only via the input solution is further subdivided into three modes of operation. The three modes may occur in testwork and full-scale operations; the effects of process variables on the rate of the process are completely different in each mode. The mode can be identified by the time at which reagent first appears in the pregnant solution. It is related to the ratio of the height of the heap and the thickness of a band of ore in which the reactions are localised. Synthesis of the phenomena occurring within a heap via a computer program has produced a quantitative relation for the reaction band thickness. The program has been validated for several different systems. The overall achievement is that the mode of operation and the rate of the process can be forecast before column testwork is commenced. Some applications of the outcomes to testwork, process design and operational tactics are described.

Jan 1, 1994

The mineral processing industry is in boom times. The focus on mill availability and therefore profitability has never been greater, as grinding mill maintenance often dictates the entire plant shut down duration. Advances in mill systemsÆ quality and reliability and the faster, safer relining afforded by RMEÆs Mill Relining Systems have significantly enhanced grinding plant availability and utilisation. Yet relining performance is still affected by the design and planning by a team of stakeholders long before the maintenance team set foot in the mill. For a greenfield grinding plant project, these team players include: 1. project owner, 2. project manager, 3. mill supplier, 4. liner supplier, 5. plant operating personnel, 6. plant maintenance personnel, 7. mill relining crew, and  8. mill reline system supplier (RME). The complex and sometimes competing design demands of mill construction and operation together with the pressure of tight timelines can result in even simple maintenance requirements being overlooked let alone optimising plant design and planning for maintenance. This paper identifies all the involved stakeholders in an effective mill relining 'team' and gives principles and considerations for each to more effectively achieve the goals within their vital roles. This paper is aimed to be a practical guide for grinding mill designers and planners to more fully exploit the advances in Mill Relining Systems and improve their mill profitability.

Jan 1, 2008

By Calvin J. Konya

When blasts are designed, we normally assume the best case situation. We assume that all burdens and spacings will be properly drilled, holes will be properly loaded, initiators will fire at the nominal time and the explosives will release their full energy. This type of precision can be obtained at a machine shop where precision equipment is available to do machining, however, in the field, no matter how well a blast is designed on paper, it most likely will not be done in the exact manner in the field.

Jan 1, 1990

By Dean Workman

Located in downtown New York City, this project necessitated an innovative conveyor design for successful muck removal. This paper will discuss the technical challenges and engineering solutions of the muck transport system which consists of every commonly recognized version of a belt conveyor. The elaborate system includes a TBM conveyor integral to the back-up system, a wall-mounted extensible conveyor, a crown-mounted transfer conveyor, a floor-mounted fixed-length conveyor, a pocket-belt vertical conveyor, three cascading overland conveyors, and one radial stacker. The most challenging design element was an over-land conveyor featuring a box truss for muck transportation over Northern Boulevard while simultaneously going under the Queens Plaza railroad viaduct. An overview of the project is provided along with the following topics: developing final plans from the proposal concept, interfacing with existing works, communication with the joint venture, and complying with local regulations.

Jan 1, 2008

By S. Banisi, A. Ghasemi, A. Fazeli, M. Rezaei, M. Maleki-Moghaddam

The efficiency of high capacity SAG mills which consume large amounts of energy depends on the grinding and slurry discharge systems. A 9.7 m × 4.8 m SAG mill with radial pulp lifters is used at the Sarcheshmeh copper complex grinding circuit. The process audit indicated that the pulp discharge system was not efficient, judging by the amount of slurry flow back and carry over. These events limited the discharge rate and increased the wear rate of the lifters and grates. With the objective of finding a new design for pulp lifters, a 3D DEM software (KMPCDEM ©), along with the plant operational data and photographic evidence was used. The KMPCDEM © software was used to compare the efficiency of the radial and curved pulp lifter design based on the material flow. The slurry flow was analysed in terms of ease of discharge and lifter wear rate. It was found that changing the radial pulp lifters to curved pulp lifters could improve the discharge efficiency,and decrease wear rate of the pulp lifter in particular at the base of the pulp lifters. The simulation results showed that if curved lifters with a radius of 0.3×mill radius are used, the amount of slurry flow back and carry over will be negligible. It is predicted that by installing the curved pulp lifters, the capacity of the mill increases by 10% and the pulp lifter service life improves by at least 20%. Keywords: SAG mill, radial pulp lifter, DEM,curved pulp lifter, Sarcheshmeh

Jan 1, 2020

By P Crittenden

Thiess Pty LtdÆs Australian Mining business unit used 7.6 PJ of energy in the 2007/2008 financial year. This represented more than 85 per cent of Thiess Pty LtdÆs total energy use and therefore meant that the Australian Mining business unit is required to conduct energy efficiency assessments and report publicly on the outcomes by December 2008 under the Federal GovernmentÆs Energy Efficiency Opportunities (EEO) Act. Thiess Pty Ltd has a policy commitment to sustainable development throughout its operations. This includes minimisation of its carbon footprint and the Australian Mining business unit has a strong focus on efficiency in all of its operations. It approached the energy efficiency assessment as an opportunity to further improve and build on its energy efficiency and greenhouse gas reduction focus in the business. As a mine contractor, Thiess faced a number of challenges in designing an assessment process that would be both effective and efficient to deliver. For example, unlike most other companies involved in the Energy Efficiency Opportunities program, the energy use associated with the Australian Mining business unit is not fixed to any single geographic location in Australia. Mining vehicles are moved from site to site according to the specific requirements of mine owners and the timing associated with the commencement and completion of contracts. Thiess departed from a traditional æsite by siteÆ based assessment and designed a ærepresentative assessmentÆ approach that involved detailed investigation of data across all sites and a focused assessment on a single site.Data and analysis was an essential part of the assessment and indicators at company, mine and site level were essential in identifying opportunities and tracking progress. Forty-six potential energy saving opportunities were identified and four of these are currently being implemented. The projects being implemented are: payload management, automating mobile lighting equipment, plant idle time management, and turbo idle downtime. The potential savings from the four major projects that have been identified are approximately 150 800 GJ/annum, equivalent to 10 600 tonnes of CO2-e/annum with a simple payback period of less than two years. Beyond the fuel savings however, there are a number of other benefits from the assessment, including operational efficiency, reduced maintenance costs and even a potential reduction in the number of vehicles required to complete the work. The EEO assessment has significantly increased the importance and urgency of energy efficiency and facilitated the sharing of good practice across all Thiess operations. Not only have four projects been adopted for immediate implementation but a further pipeline of projects is available for future possible implementation. This case study describes: how Thiess conducted its assessment including the use of energy data and indicators, the opportunities identified that are currently being implemented, and the lessons learnt and how other organisations can use these to improve their approach to energy efficiency assessments. This case study is a more comprehensive version of a case study developed for the Commonwealth Department of Resources, Energy and Tourism. The assessment results reported in this case study are drawn from the Thiess Energy Efficiency Opportunities Report 2008.

Jan 1, 2009

By R. Chryst, R. Kus

In the Integrated IT Systems proposed by Przedsie? biorstwo Robót Geologiczno-Wiertniczych—Geological and Drilling Company (PRGW) a network connects a database with all of the departments of a mining division. A key element thereof is the common graphics environment—Micro Station supplied by the firm, Bentley. PRGW’s SoftMine software and GMSI’s CadsMine that are used to design and schedule mining operate in this environment. The digital form of the design project facilitates the verification of information and the integration of technical solutions with SAP R/3 type financial—accounting systems. The system has been successfully implemented in the Brown Coal Mine in Poland.

Jan 1, 2003

In the current climate, there is a real need to bridge the gap between theory and the real world mining considerations, and develop viable, cost-effective, high performance thickeners. With a greater need to extract profits from both difficult-to-process ores and lower grade orebodies, coupled with the necessity to produce 'greener', less water intensive technologies, suppliers need to take current thickener designs to the next level and into the 21st century. The complexity of 'getting it right' within a thickenerÆs feedwell, the 'nerve centre' of the thickener, is no small task. Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, minimising unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ù all of these need to occur in the right order and in the right proportions within the feedwell. This paper discusses the genesis and evolution of a new feedwell design, the first major innovation in the thickening industry in over 15 years.

Jan 1, 2008

By T Niitti, J Turunen, P B, A Rinne

In todayÆs marketplace, with high metals prices, many operations are faced with the challenge of improving recovery in the particle size ranges which are normally difficult to recover. This presentation focuses on the various methods used to alter the flow dynamics in a mechanical flotation cell, thereby improving metallurgical results. Modern computational fluid dynamics (CFD) tools have been used in the design phase, with subsequent validation at the plant. Some of the validated variables include mixing profile, power draw and local air hold-up. This presentation underlines how modern CFD analysis can be used to screen and select different approaches before commencing costly trial-and-error experiments at plant scale. Two methods of affecting flow dynamics are discussed û firstly, by altering the geometry of the rotor-stator area and, secondly, by fitting additional features in the tank. The rotor-stator area can be modified to provide more concentrated turbulent kinetic energy or, respectively, to provide more pumping efficiency with less attrition. The tank can be fitted with various additional features, aimed to create different particle suspension profiles. The benefit of both methods is that they can be applied not only to newly installed flotation technology, but also to existing plant cells, thus enabling potential improvement in the mixing profiles, solids suspension, tank sanding and metallurgical performance. Results of several sitesÆ tests are discussed in terms of flow variables measurement as well as metallurgy. This paper demonstrates the effects of different flow dynamics on the mixing profiles and metallurgical results of existing mechanical flotation cells.

Jan 1, 2006

By D C. Curry, M F. Young

Many flotation operations need to improve liberation to increase recovery, yet often plant operators are concerned that finer grinding will produce æslimesÆ with low flotation recovery. Yet simple circuits can be designed to give good liberation and excellent fines recovery. The economics of fine grinding has changed fundamentally with new stirred milling processes like the IsaMill. This has also transformed flotation design due to the clean surfaces produced in the inert grinding environment and the narrow size distribution produced by the IsaMill. Past poor experiences with æovergrindingÆ in flotation circuits was often due to the wide size distribution and the degradation of mineral surfaces produced by conventional devices using steel media, like ball mills and tower mills. The correct practice is to design both grinding and flotation together to suit the liberation characteristics of the ore. This may result in several stages of grinding and flotation, recovering mineral as soon as it is liberated, then applying further grinding energy only to those particles that still need liberation. Flotation then occurs in relatively narrow size bands and with minerals with similar liberation characteristics. Though the circuit may look more complex on paper, in reality it is far simpler to operate since each section performs predicably. Circuit design also needs to address materials handling. Finer particles affect froth handling and dewatering, but can still be easily handled by standard products with careful attention to design of launders, pumps and pumpboxes, and de-aeration before thickening and filtering. Excellent examples of designing circuits to include ultrafine grinding include Mt Isa and McArthur River (MRM). In the last decade these operations have produced over ten million tonnes of concentrate with an average grain size below 10 ¦m and above 80 per cent recovery. At Mt Isa, zinc recovery was increased by ten per cent by applying fine grinding to existing poorly liberated streams. In fact, grinding finer in the IsaMill actually improved the recovery of fine particles by ten per cent, and maximum particle flotation recovery occurs for 10 ¦m particles. A more recent example is the flotation of Platinum Group Metals (PGMs). The use of conventional ball or tower milling to improve liberation is severely limited by the impact of commonly associated chromite on classification, and degradation of flotation performance by the steel grinding environment. The ability of open circuit IsaMills to deliver a narrowly sized ultrafine product with clean mineral surfaces is transforming the design of platinum flotation circuits. The science and practice of fine-grained flotation is now thoroughly proven. The availability of the 2.6 MW IsaMill has made ultra fine grinding a practical tool for flotation plant design. It is expected to become a standard choice for future applications of both fine-grained ores and for minerals with difficult flotation characteristics.

Jan 1, 2005

By L. Lorig

"Two types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudo-static analyses. The acceptance criteria are often promulgated by governments despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems than earthquakes. Two types of problem are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare. This paper will discuss the mechanisms for rainfall-induced slope instability, as well as analysis methods. Examples will be discussed and analysis methods are proposed. IntroductionTwo types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudostatic analyses. The acceptance criteria are often promulgated by governments (e.g., Peru, Chile) despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems when compared to earthquakes. Two types of problems are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare, but do exist. In Peru, for example, slopes are required by law to be designed for a 100-year storm."

Jan 1, 2016

In many mining operations, the truck and loader equipment represents the bulk of the invested capital and the majority of the mine operating cost. The profitability of these mines is therefore critically linked to the efficiency of the truck and loader operations. The various factors which affect the productivity of trucks and loaders are analysed by computer simulation, and the results presented in a form allowing assessment of the importance of each factor on overall productivity.

Jan 1, 1983

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986

By Sam Spearing

Free-standing supports are commonly used in coal mines in the USA, particularly when longwalling. A recent trend has been the development of prop supports. Prop supports have many advantages over bulky, crib-type secondary standing supports, particularly in regard to material handling and installation. The challenge in prop design has been to develop load capacities that can compete with crib type systems and to develop reliable (stable) yielding capability. This paper will focus on the design aspects of steel prop supports, specifically, and evaluate the various concepts that have been developed to provide easy height adjustment and sustainable stable yielding under load. The design and resulting improvement provided by recent support developments called the Quik Stik and Ball Buster are discussed in detail. Performance areas that still need improvement in the design and usage of free standing supports in general are identified and possible solutions outlined.

Jan 1, 2008

By R Ahola, M D. Henschel, M A. McParland

With the introduction in recent years of third-generation interferometric synthetic aperture radar (InSAR) techniques, monitoring of mine slopes, benches and surrounding areas has benefitted from increased accuracy and coverage. Fundamental research into point and distributed scattering techniques has pushed the use of InSAR to provide higher spatial and height resolution. In this paper we discuss the operationalisation of third-generation InSAR techniques and show its application to active mining operations.This paper will discuss the use of multiple independent measurements of ground movement obtained from operationally-derived InSAR products over a wide variety of deformation areas within an active open pit mining operation (ie pit slopes, dewatering depressions, tailings containment and waste dumps). A technique that shortens the time between observations (increased observation frequency) and provides ongoing estimates of measurement accuracy will be described. The methodology exploits available satellite data by using multiple satellites and multiple beams. The paper will also examine factors in the design of a mine survey with third-generation InSAR and illustrate some of the necessary engineering trade-offs to efficiently monitor a mine from space.Overall, this paper aims to demonstrate the capabilities and advantages of operational third-generation InSAR techniques for ground movement monitoring of mining operations and provide a framework for proper design of a mine InSAR survey.CITATION:Henschel, M D, Sato, S, Ahola, R and McParland, M A, 2014. Designing interferometric synthetic aperture radar surveys for mine monitoring with accuracy assessment, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 233–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014